S2H STEP User manual

Set the Time
and Date on
your STEP
1Activate your
STEP at
S2H.COM
2
Wear your
STEP and
Start Walking
3Upload your
Reward Code
at S2H.COM
4
Accumulate
Points on
S2H.COM
5
Redeem your
Reward at
S2H.COM
6
Quick Start Guide
Using Your Product

Table of Contents
Must Read
Turning On Your STEP
Setting the TIME
Setting the DATE
How to Wear Your STEP
Getting to 10,000 Steps
Viewing Your Reward Code
Storing Your Reward Code
Uploading Your Reward Code at S2H.COM
Taking Care of Your STEP
Warranty and Getting in Touch with S2H
FCC Regulations
1
2
3
4
5
6
7
8
9
10
11
12

English 1
Must Read
• Don’t lose the Serial Number on the back of this booklet;
you will need it to activate your STEP on S2H.COM
• The STEP is not waterproof; so please don’t get it wet.
• The battery inside your STEP can be replaced with a 1.5V
LR-43 button cell battery.
• The STEP is a pedometer, it measures only walking. Some
activities like running may not register properly.
• For a basic account at S2H.COM, you are allowed only
one upload per day.

MODE BUTTON
SET BUTTON
LCD SCREEN
PULL TAB
English 2
Turning On Your STEP
Your STEP comes turned off from the factory; to turn it on, you will
need to pull the plastic tab located on the side of the STEP. Once
you pull the tab, you will see the letters S2H displayed on the
screen. You’re now ready to set the TIME and DATE.

English 3
Setting the TIME
Press the MODE button until you see the word TIME displayed. Now
press and hold the SET button until you see the number 12 or 24
flashing. Use the MODE button to choose between 24 hour and 12
hour then use the SET button to select.
Continue to use the SET button to cycle through the remaining
settings (HOURS, MINUTES & SECONDS) and use the MODE button
to adjust the appropriate number. Once you set SECONDS you will
move on to setting the DATE. If you do nothing for 10 seconds, you
will exit the TIME & DATE setup mode.

English 4
Setting the DATE
Press the MODE button until you see the word TIME displayed. Now
press and hold the SET button until you see the number 12 or 24
flashing. Press the SET button four times until you see the
Month and Day flashing.
Use the MODE button to cycle between Month/Day and Day/Month,
and the SET button to select the date display format. Now you can
set the date; use the MODE button to set the Month or Day, depending
on your display format. Press the SET button to move on to the next
selection. Once you’re done press SET again to exit.

30° 30°
30° 30°
English 5
How to Wear Your STEP
To properly wear your STEP, simply clip it onto your belt. The closer it
is to your body the better. Don’t clip it to loose clothes or sleeves.
Make sure the STEP is mounted in a vertical position to your body
and that it stays relatively vertical in both axes.

English 6
Getting to 10,000 Steps
Your STEP will count even if it’s in TIME, DATE, and CODE mode. If
you want to clear out the step count, simply press the MODE and
SET buttons for 4seconds.
Your STEP needs to accumulate 10,000 steps in order to reveal a
Reward Code. To see the steps that you have walked, press the
MODE button until the word STEPS appears. The display will count
from 0to 10,000.

English 7
Viewing Your Reward Code
When you have earned 10,000 steps, your STEP will generate a
Reward Code. Your 12 digit Reward Code will be revealed in four
parts as shown below.
At this point you can do one of two things; (1) you can clear the
earned Reward Code by pressing MODE and SET for 4seconds or
(2) you can store the Reward Code in CODE mode. You can also
clear the Reward Code in CODE mode by pressing MODE and SET
for 4 seconds.

English 8
Storing Your Reward Code
If you earn a Reward Code in STEPS mode while one is stored in
CODE mode, you will have to either (1) clear out the Reward Code in
STEPS mode or (2) clear out the stored code in CODE mode and
push the recently earned Reward Code into CODE mode; this will
allow you to start counting more steps.
When you earn a Reward Code in STEPS mode, you can store it in
CODE mode simply by pressing SET. The Reward Code will be
pushed into CODE mode, and your step count will be reset to zero.
You can earn a new Reward Code while one is stored in CODE mode.

English 9
Uploading Your Reward Code at S2H.COM
Always remember to write down your Reward Code because once
you clear the Reward Code from your STEP, it cannot be retrieved!
Congratulations, you are now one step away from earning your S2H
POINTS. Login to S2H.COM and click on the Upload Reward Code
link in the MY ACCOUNT section, then enter the 12 digit Reward
Code that is displayed on your LCD Screen.
Sample Code
UPLOAD
C1AFHZITU3YL

BATTERY
English 10
Taking Care of Your STEP
If the display begins to fade after approximately two years, you can
simply replace the battery by removing the screw on the back cover.
You can replace it with a 1.5V LR-43 button cell battery.
Cleaning your STEP is simple; just wipe it down with a soft damp
cloth. If there are any tough stains, you can use a little bit of soap to
get them out. Do not use any harsh chemicals such as acetone or
alcohol, as they may damage the product.

English 11
Warranty & Getting in Touch with S2H
If you have any questions about your STEP, please visit S2H.COM
and click on the Contact Us link on the bottom of the web page. One
of our S2H representatives will always get back to you to answer
any questions that you may have.
Switch2Health guarantees its products for 30 days from date of
purchase. If you are unhappy for any reason with your STEP, S2H will
refund you the purchase price of the STEP. The product must be in
its original package and it must have been purchased from S2H.COM

English 12
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) Reorient or relocate the
receiving antenna. (2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for
help.
CAUTION: Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
NOTE: Manufactured April 2011

Programa la
FECHA / HORA
en tu STEP
1Activa tu
STEP en
S2H.COM
2
Usa tu STEP
y Empieza a
Caminar
3Sube tus
Códigos a
S2H.COM
4
Acumula
Puntos en
S2H.COM
5
Canjea tus
Puntos en
S2H.COM
6
Guía Rápida
Utilizar el Producto

Contenidos
Importante
Enciende tu STEP
Programa la HORA
Programa la FECHA
Como Utilizar tu STEP
Conseguir 10.000 pasos
Cómo Visualizar tu Código
Almacena tu Código
Sube tu Código a S2H.COM
Mantenimiento de tu STEP
Garantía y Contacto S2H
1
2
3
4
5
6
7
8
9
10
11

Español 1
Importante
• No pierdas el Número de Serie situado en el dorso de este
libro. Lo necesitarás para activar tu STEP en S2H.COM
• El STEP no es resistente al agua. Por favor mantenlo
alejado del agua.
• La batería del STEP puede ser remplazada por una
batería LR-43 de 1,5V.
• El STEP es un podómetro, sólo registra pasos al andar.
Algunas actividades como correr pueden no ser registradas
correctamente.
• Utilizando una cuenta SH2 básica sólo podrás subir un
código por día.

BOTÓN MODE
BOTÓN SET
PANTALLA
ETIQUETA
Español 2
Enciende tu STEP
El STEP viene apagado de fábrica. Para encenderlo deberás tirar de
la tira plástica situada en el lateral del aparato. Una vez extraída la
etiqueta plástica, verás las letras S2H en la pantalla. Ahora ya estás
listo para configurar la HORA y la FECHA.

Español 3
Programa la HORA
Aprieta el botón MODE hasta que veas la palabra TIME en la parte
inferior de la pantalla. A continuación mantén apretado el botón SET
hasta que veas el número 12 o 24 parpadeando. Utiliza el botón
MODE para elegir entre el modo de 12 o 24 horas y aprieta el
botón SET para seleccionar.
Presione repetidas veces el botón SET para navegar por el menú
(HORA, MINUTOS y SEGUNDOS) y utiliza el botón MODE para ajustar
cada parámetro. Una vez programados los SEGUNDOS serás redirigido
a la configuración de la FECHA. Si no hace nada durante 10 segundos
saldrás del modo de configuración de FECHA y HORA.