SAAS MUSCLE 3 Series User manual

Installation Instructions
CLOCK
Part No: SG32294
2 inch-52mm
Important notes before installing:
- Installing this product to your vehicle may require an adaptor. SAAS offer a large range of
adaptors and installation parts; please check with your SAAS dealer for available adaptors.
- SAAS Muscle series gauges are designed for 12volt systems ONLY!
-All installation work should be done by a qualified professional to avoid damage to this product.
- SAAS RECOMMENDS all products be tested prior to installation. This will save time and speed up
the troubleshooting process if you encounter any issues.
- BEFORE installing, please check our website (shopsaas.com) for the latest fitting instructions.
If the top left corner (v) number is different to website, please use instructions from website.
SAAS Automotive PTY LTD
25 Metrolink Circuit West, Campbellfield,
Victoria 3061 Australia
ABN: 48166279670
ACN: 166279670
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.shopsaas.com
SINCE 1954
SINCE 1954
Page 4/4
v20230530
Page 1/4
Wiring Guide:
Wire colour
Wire Function
Wire Connection Location
Vehicle body
Ground 12V-
Yellow
Park lights 12V+
Park light circuit (do NOT connect to a dimmer)
Red
Typical Layout
Wiring Diagram
Ground 12V-
Park lights 12V+
Ignition 12V+
Battery 12V+
White
Black
Ignition 12V+
Ignition harness / Fuse box
Ignition harness / Fuse box
Battery 12V+
Remote programming
button. Fit under dash
for easier programming.
(Installation optional)
Programming button
Fitting U bracket:
Remove nuts and add
stud spacers before fitting
U bracket if required.
X
Not used.
Power and link connector pinout.
Use any connector to power the
gauge and for less wiring use the
other connector with the supplied
link cable to power a second Muscle
Series 3 gauge ONLY!
Warranty Terms & Conditions:
SAAS Automotive Pty Ltd warrants this product against defects in factory workmanship and
materials for a period of twelve (12) months from the date of original purchase. This warranty
applies to the first retail purchaser, is non-transferable and covers only where the product has
been subjected to normal use or service. Provision of this warranty shall not apply to any SAAS
Automotive product that has been used for a purpose for which it is not designed, or which has
been altered in any way that would be detrimental to the performance or life of the product, or
misapplication, misuse, negligence or accident. Warranty claims to the manufacturer must be
transportation prepaid and accompanied with dated proof of purchase. On any part or product
found to be defective after examination by SAAS Automotive Pty Ltd, SAAS Automotive Pty Ltd will
only repair or replace the merchandise through the original selling dealer or on a direct basis.
SAAS Automotive Pty Ltd assumes no responsibility for diagnosis, removal and/or installation
labour, loss of vehicle use, loss of time, inconvenience or any other consequential expenses. The
warranties herein are in lieu of any other expressed or implied warranties, including any implied
warranty of suitability, and any other obligation on the part of SAAS Automotive Pty Ltd, or the
selling dealer.
For further assistance email: [e-mail]

Specifications
GAUGE INFORMATION
Problem
Possible Cause
Solution
Troubleshooting:
Contents:
In The Box
Qty
Clock gauge
Mounting U bracket
Mounting U bracket studs (M4x0.7 thread)
Mounting U bracket nuts
Fitting instructions
1
1
1
2
2
Notes
1
Operating range
8V+ to 18V+
Gauge lighting type
50mm (minimum)
Total depth of gauge
55mm (including bezel)
Mounting hole size (52mm gauges)
52mm
Gauge lighting colours
-gauge not reading
-bad connection
-check wiring for bad connections or wire
gauge directly to a battery to test
-gauge has been dropped
-replace gauge
-no back lighting
-incorrect wiring
-connected to a dimmer
-refer to fitting instructions
-refer to fitting instructions
Part No.
Mounting depth required for gauge
Please note: If you are having problems with the installation of this product, please do not
contact your retailer or SAAS until you have read ALL the troubleshooting notes below.
Page 2/4
Page 3/4
User Functions:
1
Programming button
Programming button length
1 meter
-clock won’t adjust
-incorrect wiring
-refer to fitting instructions
-programming button not
connected or damaged
-connect button or check button for
normal operation with a multimeter
red - green - blue - purple - white - amber - pink -
ice blue - orange - aqua - OFF - cycle mode
For further assistance email: [e-mail]
Current draw
0.02A - standby mode (ignition off)
Day Colour
Red
Blue
Green
Amber
Park Lights OFF
Night Colour
Park Lights ON
User Functions
Gauge will exit after 5 seconds of no activity.
Ignition ON
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Red
Blue
Green
Amber
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Note: Use the remote programming button or the button on the back of the gauge to set the below
functions.
Exit
Hold button until gauge beeps > release
button and press to set colour
Colour
setting
Press Button x1
Press Button x2
Night Brightness
Day Brightness
Park Lights OFF
Park Lights ON
1 2 3 4 5
Dark Bright
1 2 3 4 5
Dark Bright
Brightness
setting
Hold button until gauge beeps > release
button and press to set colour
Press Button x3
Clock adjust
setting
Hold button until gauge beeps > release
button and press to set clock
-back light colour is set to off
-refer to user functions
SG4106
Gauge power connector
Gauge link connector
SG5100
SG9101
SG61005
1
Gauge power harness length
Gauge link harness length
1 metre
300mm
10 colour LED with 5 levels of brightness

Specifications
GAUGE INFORMATION
Problem
Possible Cause
Solution
Troubleshooting:
Contents:
In The Box
Qty
Clock gauge
Mounting U bracket
Mounting U bracket studs (M4x0.7 thread)
Mounting U bracket nuts
Fitting instructions
1
1
1
2
2
Notes
1
Operating range
8V+ to 18V+
Gauge lighting type
50mm (minimum)
Total depth of gauge
55mm (including bezel)
Mounting hole size (52mm gauges)
52mm
Gauge lighting colours
-gauge not reading
-bad connection
-check wiring for bad connections or wire
gauge directly to a battery to test
-gauge has been dropped
-replace gauge
-no back lighting
-incorrect wiring
-connected to a dimmer
-refer to fitting instructions
-refer to fitting instructions
Part No.
Mounting depth required for gauge
Please note: If you are having problems with the installation of this product, please do not
contact your retailer or SAAS until you have read ALL the troubleshooting notes below.
Page 2/4
Page 3/4
User Functions:
1
Programming button
Programming button length
1 meter
-clock won’t adjust
-incorrect wiring
-refer to fitting instructions
-programming button not
connected or damaged
-connect button or check button for
normal operation with a multimeter
red - green - blue - purple - white - amber - pink -
ice blue - orange - aqua - OFF - cycle mode
For further assistance email: [email protected]
Current draw
0.02A - standby mode (ignition off)
Day Colour
Red
Blue
Green
Amber
Park Lights OFF
Night Colour
Park Lights ON
User Functions
Gauge will exit after 5 seconds of no activity.
Ignition ON
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Red
Blue
Green
Amber
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Note: Use the remote programming button or the button on the back of the gauge to set the below
functions.
Exit
Hold button until gauge beeps > release
button and press to set colour
Colour
setting
Press Button x1
Press Button x2
Night Brightness
Day Brightness
Park Lights OFF
Park Lights ON
1 2 3 4 5
Dark Bright
1 2 3 4 5
Dark Bright
Brightness
setting
Hold button until gauge beeps > release
button and press to set colour
Press Button x3
Clock adjust
setting
Hold button until gauge beeps > release
button and press to set clock
-back light colour is set to off
-refer to user functions
SG4106
Gauge power connector
Gauge link connector
SG5100
SG9101
SG61005
1
Gauge power harness length
Gauge link harness length
1 metre
300mm
10 colour LED with 5 levels of brightness

Installation Instructions
CLOCK
Part No: SG32294
2 inch-52mm
Important notes before installing:
- Installing this product to your vehicle may require an adaptor. SAAS offer a large range of
adaptors and installation parts; please check with your SAAS dealer for available adaptors.
- SAAS Muscle series gauges are designed for 12volt systems ONLY!
-All installation work should be done by a qualified professional to avoid damage to this product.
- SAAS RECOMMENDS all products be tested prior to installation. This will save time and speed up
the troubleshooting process if you encounter any issues.
- BEFORE installing, please check our website (shopsaas.com) for the latest fitting instructions.
If the top left corner (v) number is different to website, please use instructions from website.
SAAS Automotive PTY LTD
25 Metrolink Circuit West, Campbellfield,
Victoria 3061 Australia
ABN: 48166279670
ACN: 166279670
Phone: [phone]
Fax: [phone]
Email: [email protected]
Web: www.shopsaas.com
SINCE 1954
SINCE 1954
Page 4/4
v20230530
Page 1/4
Wiring Guide:
Wire colour
Wire Function
Wire Connection Location
Vehicle body
Ground 12V-
Yellow
Park lights 12V+
Park light circuit (do NOT connect to a dimmer)
Red
Typical Layout
Wiring Diagram
Ground 12V-
Park lights 12V+
Ignition 12V+
Battery 12V+
White
Black
Ignition 12V+
Ignition harness / Fuse box
Ignition harness / Fuse box
Battery 12V+
Remote programming
button. Fit under dash
for easier programming.
(Installation optional)
Programming button
Fitting U bracket:
Remove nuts and add
stud spacers before fitting
U bracket if required.
X
Not used.
Power and link connector pinout.
Use any connector to power the
gauge and for less wiring use the
other connector with the supplied
link cable to power a second Muscle
Series 3 gauge ONLY!
Warranty Terms & Conditions:
SAAS Automotive Pty Ltd warrants this product against defects in factory workmanship and
materials for a period of twelve (12) months from the date of original purchase. This warranty
applies to the first retail purchaser, is non-transferable and covers only where the product has
been subjected to normal use or service. Provision of this warranty shall not apply to any SAAS
Automotive product that has been used for a purpose for which it is not designed, or which has
been altered in any way that would be detrimental to the performance or life of the product, or
misapplication, misuse, negligence or accident. Warranty claims to the manufacturer must be
transportation prepaid and accompanied with dated proof of purchase. On any part or product
found to be defective after examination by SAAS Automotive Pty Ltd, SAAS Automotive Pty Ltd will
only repair or replace the merchandise through the original selling dealer or on a direct basis.
SAAS Automotive Pty Ltd assumes no responsibility for diagnosis, removal and/or installation
labour, loss of vehicle use, loss of time, inconvenience or any other consequential expenses. The
warranties herein are in lieu of any other expressed or implied warranties, including any implied
warranty of suitability, and any other obligation on the part of SAAS Automotive Pty Ltd, or the
selling dealer.
For further assistance email: [email protected]