SAAS MUSCLE DIGITAL Series User manual

Installation Instructions
Wiring Guide:
Typical Layout
Wiring Diagram
Wire colour
Wire Function
Wire Connection Location
White
Vehicle body
Battery 12V+
Ground 12V-
Black
Yellow
Illumination 12V+
Park light circuit (do NOT connect to a dimmer)
Ignition harness / Fuse box
Red
Ignition 12V+
Orange
Ignition harness / Fuse box
Mounting studs for U bracket.
Fitting U bracket: Fit supplied stud
spacers to threads before using the
supplied U bracket.
Programming
switch
Battery 12V+
Ground 12V-
Ignition 12V+
Illumination 12V+
VSS signal input
Connector pinout
Rear of gauge
SAAS Automotive PTY LTD
25 Metrolink Circuit West, Campbellfield,
Victoria 3061 Australia
ABN: 48166279670
ACN: 166279670
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.shopsaas.com
SINCE 1954
SINCE 1954
Page 1/4
Warranty Terms & Conditions:
SAAS Automotive Pty Ltd warrants this product against defects in factory workmanship and materials for a
period of twelve (12) months from the date of original purchase. This warranty applies to the first retail
purchaser, is non-transferable and covers only where the product has been subjected to normal use or
service. Provision of this warranty shall not apply to any SAAS Automotive product that has been used for a
purpose for which it is not designed, or which has been altered in any way that would be detrimental to the
performance or life of the product, or misapplication, misuse, negligence or accident. Warranty claims to the
manufacturer must be transportation prepaid and accompanied with dated proof of purchase. On any part or
product found to be defective after examination by SAAS Automotive Pty Ltd, SAAS Automotive Pty Ltd will
only repair or replace the merchandise through the original selling dealer or on a direct basis. SAAS
Automotive Pty Ltd assumes no responsibility for diagnosis, removal and/or installation labour, loss of vehicle
use, loss of time, inconvenience or any other consequential expenses. The warranties herein are in lieu of any
other expressed or implied warranties, including any implied warranty of suitability, and any other obligation
on the part of SAAS Automotive Pty Ltd, or the selling dealer.
For further assistance email: [e-mail]
Contents:
In The Box
Qty
Speedometer gauge
Wiring connector
Mounting U bracket
Mounting U bracket studs (M4x0.7 thread)
Mounting U bracket nuts
Fitting instructions
1
1
2
2
Notes
1
Part No.
1
Programming switch
1
v20220531
Not used
Part No. SG41263
Specifications
GAUGE INFORMATION
Gauge operating range
Gauge lighting type
Gauge lighting colours
Gauge operating voltage
10v > 15v
Mounting depth required for gauge
55mm (minimum)
Mounting hole size for gauge
80mm / 3 1/4”
Gauge dimensions
88mm x 70mm
Programming switch cable length
1.1mt
Wiring harness length
2mt
red - green - blue - purple - white - amber - pink -
ice blue - orange - aqua - OFF - cycle mode
10 colour LED with 5 levels of brightness
IN-DASH SPEEDOMETER (90mm)
VSS input
Dash cluster/ gearbox / PCM module
0 > 220 km/h
Speed unit type
KM/H > MPH
Recommended signal locations
Dash cluster, ECU VSS output, SAAS GPS sensor: SG31650
Important notes before installing:
- Installing this product to your vehicle may require an adaptor. SAAS make a large range of
adaptors and installation parts, please check with your SAAS dealer for available adaptors.
- This product is designed for 12volt systems ONLY!
-All installation work should be done by a qualified professional to avoid damage to this product.
- SAAS RECOMMENDS all products be tested prior to installation. This will save time and speed up
the troubleshooting process if you encounter any issues.
- BEFORE installing, please check our website (shopsaas.com) for the latest fitting instructions.
If the top left corner (v) number is different to website, please use instructions from website.
SG31015
SG4163
SG4106
Page 4/4

Vehicle Pulse Rate Set Up:
User Functions:
Page 3/4
Page 2/4
For further assistance email: [e-mail]
Note: The programming button must be connected to the back of the gauge and mounted in a location
that is easy to reach to access all functions.
Park Lights OFF
Day Brightness (D)
Night Brightness (N)
Day Color (D)
Peak readings are cleared.
Red
Blue
Green
Amber
Park Lights OFF
Night Color (N)
Park Lights ON
Park Lights ON
1 2 3 4 5
Dark Bright
1 2 3 4 5
Dark Bright
Buzzer
Fast beep
Slow beep
User Functions
Exit
Gauge will exit after 5 seconds of no activity.
Ignition ON
cl8
Press Button
Hold Button
Press Button
Hold Button
Press Button
Press Button
Hold Button
Hold Button
Press Button
Press Button
Cycle
Purple
White
Aqua
Ice Blue
Colors
bp
Brightness
Buzzer type
hb
Buzzer levels
ob
Buzzer high
Buzzer low
Buzzer off
Hold Button
VO - (0)
VO - (1)
VO - (2)
VO - (3)
Buzzer medium
Press Button
ac
Release button and press again to set display type for gauge start up and
shutdown.
Hold Button
AC - (1)
AC - (2)
AC - (3)
Open/close type
Speed Warning
Hold Button
Release button then press and hold to set Speed warning value.
(Speed warning range - 40 > 211 km/h)
Press Button
Hold Button
O
Peak
Od Display
Hold Button
88
Release and press button again to choose from 3 odometer display types.
Press Button
Pink
Orange
Off
Red
Blue
Green
Amber
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Use Free mode (F00) if vehicle pulse rate is unknown. Setting Free mode: Select (F00) > Press
and hold button until display shows (FrE) > Drive vehicle to 60km/h and press button once > Speed
pulse has been set.
km/h
PULSE SET
Hold Button
Release Button
Gauge will return to main
window after 5 seconds.
km/h
Ignition ON
To adjust Vehicle
Pulse Rate.
Press button once to
select pulse rate.
2
4
8
16
Pulse Set
-use free pulse setting if all other settings
are out of range
- Additional troubleshooting notes:
Problem: “Free pulse setting used but speed reading is still out”
- If your speed reading is still out, instead of pressing the programming button at 60 KM/H, try
pressing it a 58 KM/H or 62 KM/H. This method will help fine tune your speed reading but may not
work on some vehicles.
Problem
Possible Cause
Solution
Troubleshooting:
-gauge not reading
-reading erratically
-bad connection on gauge
-test for power at the back of the gauge
-no back lighting
-incorrect wiring
-refer to fitting instructions
Please note: If you are having problems with the installation of this product, please do not
contact your retailer or SAAS until you have read ALL the troubleshooting notes below.
-gauge reading is out
-wrong pulse setting
-change pulse setting and retry
-wrong VSS wire
-refer to vehicles workshop manual for
correct wire
-wrong pulse setting
WARNING! SAAS strongly recommends that you have help with this part of the setup!
⚠
Scale Type
s8
Release and press button again to choose from 3 types of display scales.
So - (1)
So - (2)
So - (3)
Trip A - (1)
Trip B - (2)
Odometer - (3)
0
f00
F00 (Free mode)
0
Unit Set: km/h - MPH
Setting speed unit: Press and hold programming button > turn ignition on > release button and
press again to change speed unit from km/h to MPH > gauge will return to main screen after 5
seconds > programming done.
Odometer Input Setting:
Resetting Trip A/B meter: Press and hold programming button for 3
seconds to reset trip meter from the main screen.
Setting odometer: Press and release programming button until (od) is displayed > press and
hold button until (odo) is displayed > release button then press and hold until first digit flashes >
release button and press again to change first digit > press and hold button to move to next digit
and repeat steps > gauge will exit after 5 seconds of no activity.
-weak VSS or bad VSS signal
-VSS signal wire may need a resistor or
diode to rectify voltage or pulse

Vehicle Pulse Rate Set Up:
User Functions:
Page 3/4
Page 2/4
For further assistance email: [email protected]
Note: The programming button must be connected to the back of the gauge and mounted in a location
that is easy to reach to access all functions.
Park Lights OFF
Day Brightness (D)
Night Brightness (N)
Day Color (D)
Peak readings are cleared.
Red
Blue
Green
Amber
Park Lights OFF
Night Color (N)
Park Lights ON
Park Lights ON
1 2 3 4 5
Dark Bright
1 2 3 4 5
Dark Bright
Buzzer
Fast beep
Slow beep
User Functions
Exit
Gauge will exit after 5 seconds of no activity.
Ignition ON
cl8
Press Button
Hold Button
Press Button
Hold Button
Press Button
Press Button
Hold Button
Hold Button
Press Button
Press Button
Cycle
Purple
White
Aqua
Ice Blue
Colors
bp
Brightness
Buzzer type
hb
Buzzer levels
ob
Buzzer high
Buzzer low
Buzzer off
Hold Button
VO - (0)
VO - (1)
VO - (2)
VO - (3)
Buzzer medium
Press Button
ac
Release button and press again to set display type for gauge start up and
shutdown.
Hold Button
AC - (1)
AC - (2)
AC - (3)
Open/close type
Speed Warning
Hold Button
Release button then press and hold to set Speed warning value.
(Speed warning range - 40 > 211 km/h)
Press Button
Hold Button
O
Peak
Od Display
Hold Button
88
Release and press button again to choose from 3 odometer display types.
Press Button
Pink
Orange
Off
Red
Blue
Green
Amber
Cycle
Purple
White
Aqua
Ice Blue
Pink
Orange
Off
Use Free mode (F00) if vehicle pulse rate is unknown. Setting Free mode: Select (F00) > Press
and hold button until display shows (FrE) > Drive vehicle to 60km/h and press button once > Speed
pulse has been set.
km/h
PULSE SET
Hold Button
Release Button
Gauge will return to main
window after 5 seconds.
km/h
Ignition ON
To adjust Vehicle
Pulse Rate.
Press button once to
select pulse rate.
2
4
8
16
Pulse Set
-use free pulse setting if all other settings
are out of range
- Additional troubleshooting notes:
Problem: “Free pulse setting used but speed reading is still out”
- If your speed reading is still out, instead of pressing the programming button at 60 KM/H, try
pressing it a 58 KM/H or 62 KM/H. This method will help fine tune your speed reading but may not
work on some vehicles.
Problem
Possible Cause
Solution
Troubleshooting:
-gauge not reading
-reading erratically
-bad connection on gauge
-test for power at the back of the gauge
-no back lighting
-incorrect wiring
-refer to fitting instructions
Please note: If you are having problems with the installation of this product, please do not
contact your retailer or SAAS until you have read ALL the troubleshooting notes below.
-gauge reading is out
-wrong pulse setting
-change pulse setting and retry
-wrong VSS wire
-refer to vehicles workshop manual for
correct wire
-wrong pulse setting
WARNING! SAAS strongly recommends that you have help with this part of the setup!
⚠
Scale Type
s8
Release and press button again to choose from 3 types of display scales.
So - (1)
So - (2)
So - (3)
Trip A - (1)
Trip B - (2)
Odometer - (3)
0
f00
F00 (Free mode)
0
Unit Set: km/h - MPH
Setting speed unit: Press and hold programming button > turn ignition on > release button and
press again to change speed unit from km/h to MPH > gauge will return to main screen after 5
seconds > programming done.
Odometer Input Setting:
Resetting Trip A/B meter: Press and hold programming button for 3
seconds to reset trip meter from the main screen.
Setting odometer: Press and release programming button until (od) is displayed > press and
hold button until (odo) is displayed > release button then press and hold until first digit flashes >
release button and press again to change first digit > press and hold button to move to next digit
and repeat steps > gauge will exit after 5 seconds of no activity.
-weak VSS or bad VSS signal
-VSS signal wire may need a resistor or
diode to rectify voltage or pulse

Installation Instructions
Wiring Guide:
Typical Layout
Wiring Diagram
Wire colour
Wire Function
Wire Connection Location
White
Vehicle body
Battery 12V+
Ground 12V-
Black
Yellow
Illumination 12V+
Park light circuit (do NOT connect to a dimmer)
Ignition harness / Fuse box
Red
Ignition 12V+
Orange
Ignition harness / Fuse box
Mounting studs for U bracket.
Fitting U bracket: Fit supplied stud
spacers to threads before using the
supplied U bracket.
Programming
switch
Battery 12V+
Ground 12V-
Ignition 12V+
Illumination 12V+
VSS signal input
Connector pinout
Rear of gauge
SAAS Automotive PTY LTD
25 Metrolink Circuit West, Campbellfield,
Victoria 3061 Australia
ABN: 48166279670
ACN: 166279670
Phone: [phone]
Fax: [phone]
Email: [email protected]
Web: www.shopsaas.com
SINCE 1954
SINCE 1954
Page 1/4
Warranty Terms & Conditions:
SAAS Automotive Pty Ltd warrants this product against defects in factory workmanship and materials for a
period of twelve (12) months from the date of original purchase. This warranty applies to the first retail
purchaser, is non-transferable and covers only where the product has been subjected to normal use or
service. Provision of this warranty shall not apply to any SAAS Automotive product that has been used for a
purpose for which it is not designed, or which has been altered in any way that would be detrimental to the
performance or life of the product, or misapplication, misuse, negligence or accident. Warranty claims to the
manufacturer must be transportation prepaid and accompanied with dated proof of purchase. On any part or
product found to be defective after examination by SAAS Automotive Pty Ltd, SAAS Automotive Pty Ltd will
only repair or replace the merchandise through the original selling dealer or on a direct basis. SAAS
Automotive Pty Ltd assumes no responsibility for diagnosis, removal and/or installation labour, loss of vehicle
use, loss of time, inconvenience or any other consequential expenses. The warranties herein are in lieu of any
other expressed or implied warranties, including any implied warranty of suitability, and any other obligation
on the part of SAAS Automotive Pty Ltd, or the selling dealer.
For further assistance email: [email protected]
Contents:
In The Box
Qty
Speedometer gauge
Wiring connector
Mounting U bracket
Mounting U bracket studs (M4x0.7 thread)
Mounting U bracket nuts
Fitting instructions
1
1
2
2
Notes
1
Part No.
1
Programming switch
1
v20220531
Not used
Part No. SG41263
Specifications
GAUGE INFORMATION
Gauge operating range
Gauge lighting type
Gauge lighting colours
Gauge operating voltage
10v > 15v
Mounting depth required for gauge
55mm (minimum)
Mounting hole size for gauge
80mm / 3 1/4”
Gauge dimensions
88mm x 70mm
Programming switch cable length
1.1mt
Wiring harness length
2mt
red - green - blue - purple - white - amber - pink -
ice blue - orange - aqua - OFF - cycle mode
10 colour LED with 5 levels of brightness
IN-DASH SPEEDOMETER (90mm)
VSS input
Dash cluster/ gearbox / PCM module
0 > 220 km/h
Speed unit type
KM/H > MPH
Recommended signal locations
Dash cluster, ECU VSS output, SAAS GPS sensor: SG31650
Important notes before installing:
- Installing this product to your vehicle may require an adaptor. SAAS make a large range of
adaptors and installation parts, please check with your SAAS dealer for available adaptors.
- This product is designed for 12volt systems ONLY!
-All installation work should be done by a qualified professional to avoid damage to this product.
- SAAS RECOMMENDS all products be tested prior to installation. This will save time and speed up
the troubleshooting process if you encounter any issues.
- BEFORE installing, please check our website (shopsaas.com) for the latest fitting instructions.
If the top left corner (v) number is different to website, please use instructions from website.
SG31015
SG4163
SG4106
Page 4/4