SACKit WOOFit User manual

S
WOOFit
User Manual

1
UK
Box Contents
- WOOFit S speaker
- User manual
- 2-in-1 charging cable
Thank you!
Thank you for purchasing this
WOOFit S speaker from SACKit.
Please read this manual carefully before
use. We are not responsible for any
person or property damage caused by
improper use of this product. We hope
you enjoy the louder, richer sound, and
features from your WOOFit S device.
Please save this user manual for later
supervision and guidance securing
correct use of the product.
Embrace life with your new SACKit
product!
Remember
Remember to register your new
SACKit product on our website:
www.SACKit.eu/reg

Quick Start Guide
2
UK
1. Charge the WOOFit S Speaker using
the included micro USB charging
cable for no less than 2 hours
2. Turn on WOOFit S
3. Turn on Bluetooth on the device you
wish to connect with
4. Choose SACKit in the Bluetooth
settings on your device
5. Start playing music from your device
6. Enjoy the music and dance

3
UK
Micro USB
input
Micro SD PlayerMini Jack
input/
AUX out
Power button
- Micro USB input
- Mini jack input
- AUX out
- Micro SD player
- Power button
- Light indicator
- Microphone
- M (Mode) button
- Play/Pause button
- Volume (-) button
- Volume (+) button
Mode
Play/Pause Volume +
Volume -
Light indicator
Microphone

4
UK
Power button
This button must be slided right to turn
on the WOOFit S speaker, and to the
left to turn the device off.
M (mode) knap
Push the Mode button to switch
between micro SD player, AUX OUT
and Bluetooth mode. If there is no
Micro SD card in the WOOFit S speaker,
this mode will automatically be skipped.
Play/Pause
When the device is in Bluetooth mode
a push on the Play/Pause button will
either play or pause the music.
Volume buttons (-/ +)
These buttons makes it possible to
adjust the sound level. When WOOFit S
is in Bluetooth mode a ”bip” sound will
be given when the sound level reaches
maximum. This warning sound will not
occur when the speaker is in AUX OUT
mode.
Buttons

5
UK
To charge the WOOFit S speaker, the
included Micro USB charging cable
must be inserted in the Micro USB input
on WOOFit S and be connected to a
computer or an adapter.
The charging begins automatically
whether the system is on or off. The
charging status can be seen on the
light indicator. During charging the
light indicator will light up red. When
the battery is fully charged the light
indicator will light up green. A full charge
of WOOFit S takes approximately two
hours.
Charging
Bluetooth
1. WOOFit S is turned on by sliding the
power button to the right. When the
light indicator alternately ashed blue
and red, WOOFit S is ready for pairing
with desired device. Please notice that
pairing mode automatically will voided
after 5 minutes if not paired. If this
happens, the WOOFit S speaker will
have to be restarted.
2. Perform the connection procedure
on your Bluetooth device to nd the
WOOFit S speaker. This system is
indicated as ”SACKit”.
Connections

6
UK
If ”SACKit” does not appear on the
list of found devices, the connection
process must be started over. Note
that the two units should be in one
meter radius of each other during the
connection.
3. Choose the ”SACKit” connection on
your Bluetooth device.
4. When the connection is established
the light indicator will ash slowly in
the colour blue. Next time the WOOFit
S speaker get turned on, a connection
will automatically be made with the last
paired device.
5.Notice: If passcode* input is
demanded on your Bluetooth device
enter ”0000”. Passcode may also appear
under the synonyms as; ” Passkey ”, ”Pin
Number” or ”Password”
Phone call
If music is playing when in the Bluetooth
mode and you have an incoming call,
WOOFit S will automatically switch to
hands-free mode. Press the Play/Pause
button to accept the call. To hang up
press the Play/Pause button again. Two
short pushes on the Play/Pause button
will make WOOFit S redial.

7
UK
AUX connection
Press one time on the Mode button
to choose ”AUX OUT” as mode. The
Light indicator will now light up green.
To adjust the sound level the volume
buttons +/- has to be pressed and hold
down. A short push on the +/- buttons
works as Play/Pause buttons in this
mode.
Mini jack input
This input enables to connect
headphone to WOOFit S. When the
headphones is connected, the sound
level will be down adjusted immediately,
but within two seconds the level will
gradually increase to protect the user
from hearing damage.
Micro USB input
This input is used for charging with the
included Micro USB charging cable. This
input can also be used for playing music
from your computer via jack input.
Micro SD player
This input enables the function of playing
your music directly from a Micro SD
card. Insert the Micro SD card and press
the mode button to choose the correct
mode. The light indicator will now ash
green and blue to indicate the correct
mode. The sound level is adjusted by
holding the volume buttons down. One
short push on the volume button will
work as Play/Pause buttons in this mode.

8
UK
Home Systems
It is possible to connect WOOFit S to a
home system. To do this, use a standard
stereo mini-jack (3.5 mm.).
No light: WOOFit S speaker is turned
off.
Green light: WOOFit S is fully charged
or WOOFit is turned on.
Blue and green ash: Micro SD Player
is active.
Red and blue ash: WOOFit S is
searching for Bluetooth device.
Red light: WOOFit S is charging.
Blue ash slowly: Connection
between WOOFit S and Bluetooth
device has failed.
Fast blinking green: Music is playing
from Bluetooth device.
Light Indicator

9
UK
Connection problems
WOOFit S Bluetooth locks on the last
connected device, which
requires the connection to be
disconnected before a new unit to
be connected to WOOFit S. This can
be done on the connected device (in
Bluetooth settings) or by resetting the
speaker. WOOFit speaker is reset by
holding the mode button down for 3
seconds and disconnect the Bluetooth
signal. The speaker is now ready to
connect with a new Bluetooth device.
Audio quality problems
If the audio quality is poor, a reason
might be low battery level. Therefor
always try to fully charge WOOFit S to
secure the absolutely best audio quality.
Warning
To prevent damage, re or electric
shock, it is strictly forbidden to remove
or replace parts of the unit. Always
consult a professional workshop or a
qualied service center if the unit has
been damaged.
Troubleshooting

10
UK
Safety Precautions
Please read and follow these
instructions to ensure correct and safe
use of WOOFit S loudspeaker.
Charge WOOFit S minimum of 2 hours
using the supplied USB cable before you
use the speaker for the rst time.
Do not expose WOOFit S to rain, water
or store it in humid environments.
Do not place WOOFit S in or near any
sort of liquids.
Do not place WOOFit S in or near
sources of re. (E.g.: Candles, replaces
or other places with open re.)
Avoid placing WOOFit S on surfaces that
are hot, dusty, or emit vibrations.
WOOFit S must only be placed on stable,
at and horizontal surfaces.
Do not place objects on top of WOOFit S.
Do not use excessive force or violence
when operating the speaker buttons.
Use and store only the USB cable properly
and safely, both during and after use.
If cleaning of the speaker is needed, use
only a dry, clean and soft cloth without
corrosive solvents or detergents.

UK
11
Operation Voltage: 3.7 V
Charging Voltage: 5V
Output Power: 3 W
Speaker Spec.: 40 mm 2.6 Ω 3 W
Frequency Response: 60Hz – 18 KHz
Lithium Battery Capacity: 430 mA/H
THD: ≤ 0.5%
SNR: ≥ 95 dB
Dimensions: D: 60 mm. H: 54 mm.
Technical Specications

UK
12
Notice
The Bluetooth function has rst priority,
so when you play music from another
Bluetooth device the audio from
another mode (AUX OUT or Micro SD
Player) stops.
When playing from a Bluetooth device
stops, WOOFit S automatically returns
to the previous mode after 3 seconds.
The battery level of WOOFit S will
only show on Iphone and Ipad device.
Other Bluetooth devices will not give
information on the battery level.

www.SACKit.eu

WOOFit

S
WOOFit
Brugermanual

Tak!
Tak fordi du har valgt WOOFit S
højttaleren fra SACKit!
Vi beder dig læse denne manual
grundigt, før du tager din nye højttaler
i brug. Vi er ikke ansvarlige for person-
eller produktskader forårsaget af forkert
eller uansvarlig brug af produktet. Vi
håber, at du kommer til at nyde den
kraftige krystalklare lyd og de smarte
funktioner i din nye WOOFit S højttaler.
Gem altid manualen, således du kan slå
op i den senere for kyndig vejledning til
korrekt brug.
God fornøjelse med dit nye SACKit
produkt!
Indhold
- WOOFit S højtaler
- Brugermanual (EN, DK, DE)
- 2-i-1 opladerkabel
17
DK
Husk
Husk at registrere dit nye SACKit
produkt på vores hjemmeside:
www.SACKit.dk/reg

Quick Start Guide
1. Oplad WOOFit S højttaleren med
vedlagte micro USB kabel i minimum
2 timer.
2. Tænd WOOFit S
3. Tænd Bluetooth på den enhed, du
ønsker at tilslutte
4. Vælg SACKit under Bluetooth-
indstillinger på din enhed
5. Start afspilning af musik på din enhed
6. Nyd musikken og dans
DK
18

Micro USB
indgang
Micro SD PlayerMini Jack
indgang/
AUX out
Tænd/Sluk
- Micro USB indgang
- Mini jack indgang
- AUX out
- Micro SD player
- Tænd/sluk
- Lysindikator
- Mikrofon
- Mode knap
- Play/Pause knap
- Volume (-) knap
- Volume (+) knap
19
DK
Mode
Play/Pause Volume +
Volume -
Lysindikator
Mikrofon