Safe Fleet PRIME DESIGN CSU-3001 User manual

CSU-3001–3002
Page 2 Packaging Contents
Page 3 Requirements & Assembly Instructions
Pages 3–5 Assembly Instructions
Cantilever Shelving Upright Assembly

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
2
CSU-3001–3002 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
1—Cantilever Shelving Upright ............................. (Qty 1)
Part numbers and height specications:
CSU-3001: 74” SUPPORT (HIGH ROOF CARGO VAN)
CSU-3002: 65” SUPPORT (MID ROOF CARGO VAN)
* Check your vehicle layout configuration and OEM for correct product.
2—HKT-0204 ........................................................ (Qty 1)
NOTE: Reserve the following Hardware
from HKT-0204 for installing your Upright
into your Cantiliever Mounting System
(sold separately).
M8 x 25MM (2X)
M8 x 25MM
M8 x 70MM (2X)
Nut Rivet (1X)
Mounting Leg Bracket (2X)
Lock Washer (2X)
Lock Washer
Flat Washer (4X)
Flat Washer
1X 1X (1X)
Locknut (1X)
Hinge Pin (4X)
Retain Ring (8X)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
3
ASSEMBLY REQUIREMENTS
CSU-3001-3002 ASSEMBLY INSTRUCTIONS–REQUIREMENTS
SHELVING ASSEMBLY SEQUENCE
Install a Retain Ring on one side of each
Hinge Pin (4 total per Upright).
1
Install a Hinge Pin and Retain Ring in the holes
shown below.
2
• These instructions are subject to change if the manufacturer revises
the parts and/or production of the subsystems and accessories used in
the brand’s vehicles. Following the instructions for assembly will ensure
proper installation of the product. The manufacturer will not be held
liable if these instructions are not followed.
• The addition of parts and/or components not original to this Cantilever
Shelving are discouraged. Use only OEM supplied parts.
• Consultaion of the OEM vehicle may be required during assembly to
avoid vehicle damage. Ensure bolt locations will not damage any
critical parts of the vehicle–i.e. gas tank, wiring harnesses, or
hoses-before drilling.
INSTALLER NOTE: It is important to correctly follow
these assembly instructions. These instructions for
assembly are provided by the manufacturer at time of
Cantilever Shelving delivery, and reect the technical
specications applicable at the time of writing.
Torque Wrench w/13MM Socket
“E-Style” Retaining Ring Applicator Tool
Plus Nut Applicator Tool
REQUIRED
RECOMMENDED

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
4Attach upper Shelving to the supports as shown.
3
Align holes
Install Hinge Pin and
Retain Ring as shown.
4
CSU-3001-3002 ASSEMBLY INSTRUCTIONS
Repeat Steps 3–5 to install the
lower Shelf.
6
The Shelving Lock
is engaged when
shelving is open.
To disengage and
close shelving,
pull lock out and
down as shown in
Figure 2.
Close the shelving
in preparation for
the next steps.
5
Figure 1
Figure 2

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪
TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
5
CSU-3001-3002 ASSEMBLY INSTRUCTIONS
M8 x 25M Bolt
Lock Washer
Flat Washer
Plus Nut
Vehicle Floor
When installing shelving, note the
mounting feet on the uprights are
adjustable and may be switched
to the other side of the upright if
required. Install shelving unit per
vehicle/OEM instructions.
8
M8 x 75M Bolt
Flat Washer
Flat Washer
Locknut
Mounting Leg
Bracket
If not pre-installed: attach the Mounting Leg
Bracket to your Upright as shown according to your
conguration and torque to 90 in-lbs.
NOTES: Mounting Leg Bracket construction varies
per conguration. The view below is for illustrative
purposes only. Install per your vehicle/OEM
instructions and layout needs.
7
WARNING: Before drilling, ensure
the bolt location will not damage any
critical parts of the vehicle–i.e. gas tank,
wiring harnesses, or hoses.
Cantilever Shelving is now ready
to install into your Vehicle. Refer to
your Cantilever Shelving Mounting
Assembly Manual to mount Cantilever
Shelving to your Vehicle interior wall.
Proceed to Step 8 to Install Upright
Mounting Feet to your Vehicle oor.

Page Intentionally Left Blank

Page Intentionally Left Blank

USAM-CSU3001-3002-US01 Rev-A 0621