SafeCom Nuance Mx User manual

Nuance Mx Proximity Reader
Reference Manual
D60829-07
February 2015

D60829-07
2
Trademarks: Nuance, the Nuance logo, SafeCom, SafeCom Go, SafeCom P:Go,
SafeCom ePay and the SafeCom logo are trademarks of Nuance
Communications, Inc. or its affiliates in the United States and/or other
countries. All other trademarks referred to herein are the property of their
respective owners. Nuance Communications, Inc. cannot be held responsible for
any technical or typographical errors and reserves the right to make changes to
products and documentation without prior notification.
Third Party Software: This software may contain third party software which
requires notices and/or additional terms and conditions. Such required third
party software notices and/or additional terms and conditions are located in
the SafeCom Third Party Notice document.
Patent: Nuance Communications, Inc. has received the following British patent
GB 2350 713 B, US patent US 6,952,780 B2 and Europe EUR EP1 120 701.
© Copyright 1995 - 2015 Nuance Communications, Inc. All rights reserved

D60829-07
3
Table of contents
1Introduction ............................................................................................4
1.1 Audience.....................................................................................4
1.2 Nuance Mx Proximity Reader series.....................................................4
1.3 Requirements ...............................................................................6
1.4 Available documentation .................................................................7
1.5 About this manual..........................................................................7
1.6 Document history ..........................................................................8
2Planning your SafeCom solution ...................................................................9
2.1 Overview.....................................................................................9
2.2 Card reader compatibility .............................................................. 10
2.3 Supported protocols ..................................................................... 11
2.4 Devices and reader types ............................................................... 12
2.5 Card testing ............................................................................... 13
2.5.1 Introduction ............................................................... 13
2.5.2 Card test in SafeCom Administrator .................................. 14
2.5.3 Card test in Notepad (keyboard emulation) ......................... 14
2.5.4 Card test with tracer firmware loaded in reader................... 15
2.6 Hardware details ......................................................................... 15
2.6.1 Electrostatic Discharge (ESD) Handling Procedures ................ 15
2.6.2 HP hardware integration pocket (HIP)................................ 16
2.6.3 SafeCom Color Front-ends .............................................. 17
2.6.4 Serial connected Nuance Mx Proximity Readers .................... 18
2.6.5 Product label details..................................................... 19
3AppBlaster ............................................................................................ 20
3.1 Introduction ............................................................................... 20
3.2 Requirements ............................................................................. 20
3.3 Install AppBlaster ........................................................................ 20
3.4 Start AppBlaster .......................................................................... 21
3.5 Configure selective card reading ...................................................... 21
3.5.1 Save Project............................................................... 23
3.5.2 Create a production image ............................................. 23
3.5.3 Loading a production image ............................................ 24
3.6 Advanced configuration ................................................................. 24
3.7 Loading firmware images ............................................................... 25
3.7.1 Loading non-keyboard emulation firmware ......................... 25
3.7.2 Loading keyboard emulation firmware ............................... 25
3.7.3 Loading tracer firmware ................................................ 26
3.8 Install USB driver ......................................................................... 26
4Troubleshooting ..................................................................................... 27
4.1 Reader does not work with a computer.............................................. 27
4.2 Reader does not work with the SafeCom Administrator .......................... 27
4.3 Reader does not work with a device.................................................. 27
4.4 Reader does not work with a particular card ....................................... 27
4.5 Same card results in different ID codes .............................................. 28
4.6 The ID code appear different in SafeCom Administrator and Notepad ......... 28
4.7 Reader behaves differently after RMA process ..................................... 28
5Index ................................................................................................... 29

1 Introduction
D60829-07
4
1Introduction
1.1 Audience
This manual is intended for certified SafeCom professionals involved in
deployment of SafeCom Smart Printing solutions.
1.2 Nuance Mx Proximity Reader series
Nuance Mx Proximity Reader series consists of multiprotocol proximity ID
devices that works with SafeCom products and allow users to authenticate
themselves by presenting their contactless ID card, tag or key fob to the
proximity reader.
The Nuance Mx Proximity Reader series uses Radio Frequency Identification
(RFID) technology. The series supports low frequency (125kHz) and high
frequency (13.56MHz) and multiple protocols within those frequencies,
including, but not limited to popular ones like: Mifare, HID Prox, EM, Hitag,
iClass, Indala, Legic and many more. Complete list is in (2.3).
The Nuance Mx Proximity Reader series consists of:
Nuance Mx Proximity Reader
This variant is the most popular.
Nuance Mx Legic Proximity Reader
The Legic variant has different print circuit
board, is used primarily in Europe and is more
expensive.
Readers are available in the color black with 2.0 meter cable with either a USB
or Serial (PS2) connector.
A module (print circuit board without casing) with mini-
USB connector is also available and is primarily intended
for mounting inside HP device’s hardware integration
pocket (2.6.2).

1 Introduction
D60829-07
5
Readers can be ordered as keyboard (KBD) emulating and non-keyboard
emulating. It is possible to swap emulation by changing the firmware (3.7) and
it is also possible to get selective card readings by enabling/disabling protocols
(3.5).
Nuance Mx
P/N
Nuance Mx Proximity Reader, USB
SC0970920
Nuance Mx Proximity Reader, USB, KBD
SC0970930
Nuance Mx Proximity Reader Module
SC0970940
Nuance Mx Proximity Reader, Serial
SC0970910
Nuance Mx Legic
P/N
Nuance Mx Legic Proximity Reader, USB
SC0976920
Nuance Mx Legic Proximity Reader, USB, KBD
SC0976930
Nuance Mx Legic Proximity Reader Module
SC0976940
Nuance Mx Legic Proximity Reader, Serial
SC0976910
Pricing and part numbers are available in SafeCom G4 price list version 7.3 or
newer. Details about the Nuance Mx product labels can be found in (2.6.5).
The Nuance Mx Proximity Reader series is available as SafeCom Color Front-
ends also.
SafeCom Color Front-ends
P/N
SafeCom Color Front-end, Mx
SC0970900
SafeCom Color Front-end, Mx Legic
SC0976900

1 Introduction
D60829-07
6
1.3 Requirements
In order to use the Nuance Mx Proximity Reader series the following
requirements apply:
For use with MFPs and printers, the SafeCom device product (SafeCom
Go, SafeCom Controller or SafeCom ID Controller) must be updated to a
version listed below or newer.
For using SafeCom Administrator with Mx card readers connected to a
computer, you must run SafeCom G4 Server version S82 070.520*03 from
February 5, 2014 or later. Earlier versions of SafeCom G4 Server and
SafeCom G3 Server (versions S82 070.440*04 to S82 070.440*08 inclusive)
can be updated to support the Nuance Mx Proximity Readers by installing
an updated version of the SafeCom Administrator.
Table 1 Supported SafeCom products
SafeCom Device
Products
Version
Date
SafeCom Device Server
Fuji Xerox,
HP, HP Sx, HP Pro1,
Sharp,
Xerox
S82 060.090*04
2014-02-05
SafeCom Go Canon
S88 010.020*14
2013-11-18
SafeCom Go HP FutureSmart
S95 nnn.050*24
2013-11-20
SafeCom Go HP
S89 nnn.050*24
2014-01-27
SafeCom Go Kyocera
S96 020.060*02
2014-11-14
SafeCom Go Lexmark
S93 041.030*15
2013-01-20
SafeCom Go Ricoh
S87 nnn.030*03
2014-12
SafeCom Go Samsung
S94 010.010*15
2014-04-25
SafeCom Controller
S80 508.780*68
2013-08-13
SafeCom ID Controller
S80 602.102*87
2014-02-07
SafeCom Server
Products
Version
Date
SafeCom G4 Server
S82 070.520*03
2014-02-05
S82 070.520*022
2013-11-19
1
HP printer firmware update may be required for HP Officejet Pro.
2
SafeCom G4 Server version S82 070.520*02 and above support the Nuance Mx
Proximity Reader in non-keyboard emulation mode. SafeCom G4 Server version S82
070.510*02 and earlier require SafeCom Administrator (10.52.3.3) patch for keyboard
emulation mode support.

1 Introduction
D60829-07
7
SafeCom G3 Server
Patch required3
2013-01-31
SafeCom G2 Server
Not supported
Not supported
1.4 Available documentation
SafeCom Smart Printing
SafeCom Smart Printing Administrator’s Quick Guide D10600
How to install a SafeCom Smart Printing solution.
SafeCom G4
SafeCom G4 Administrator’s Manual D60650
A comprehensive Manual that the administrator should consult to make a
successful SafeCom solution. Includes information about SafeCom
Tracking, SafeCom Rule Based Printing, SafeCom Client Billing, and
SafeCom Pay.
1.5 About this manual
This manual applies to Nuance SafeCom G4 Server version S82 070.520*07.
This manual is organized as follows:
Chapter 1 Introduction lists the supplied SafeCom documentation,
introduces system requirements, and describes how this manual is
organized.
Chapter 2 Planning your SafeCom solution describes what considerations
should be taken when deploying the Nuance Mx proximity readers in
existing and new SafeCom solutions.
Chapter 3 AppBlaster describes how to install the AppBlaster application
and use it to update the firmware and change the configuration of the
Nuance Mx Proximity Readers.
Chapter 4 Troubleshooting contains hints for troubleshooting.
3
SafeCom G3 Servers (S82 070.440*04 to S82 070.440*08 versions inclusive) require
SafeCom Administrator (9.44.4.4) patch. Previous G3 versions require an upgrade to a
minimum of S82 070.440*04 to support Mx card readers, connected to a computer,
running SafeCom Administrator.

1 Introduction
D60829-07
8
1.6 Document history
Revision D60829-07
Updated Appblaster version to 1.49 (3).
Revision D60829-06
Updated Requirements with information on patching the SafeCom
Administrator (1.3).
Updated requirements for SafeCom Go Kyocera to version S96 020.050*02.
Revision D60829-05
Updated requirements for SafeCom Go Samsung to version S94
010.010*15, as the previous version S94 010.010*14 cannot be installed
after May 19, 2014, due to expired certificate (1.3).
Cotag is disabled by default (2.3).
Inserted recommendation to always save configuration as project (3.5).
Added: Reader behaves differently after RMA process (4.7).
Revision D60829-04
Updated Requirements (1.3).
Added introduction to card testing (2.5.1).
Added section on product label details (2.6.5).
Removed support for TIRIS/HDX protocol operating at 134.2 kHz.
Revision D60829-03
Updated Requirements (1.3).
Added section on Electrostatic Discharge (ESD) Handling Procedures
(2.6.1). Added hardware details for SafeCom Color Front-ends (2.6.3) and
Serial readers (2.6.4).
Revision D60829-02
Minor corrections. Updated Requirements (1.3).
Revision D60829-01
Initial version.

2 Planning your SafeCom solution
D60829-07
9
2Planning your SafeCom solution
2.1 Overview
The Nuance Mx proximity readers come with preloaded firmware with all
supported protocols enabled. This means that in most cases the readers can be
deployed as is. However, there are some scenarios that require some planning:
User behavior:
Presenting multiple cards at a time
If a user is storing multiple proximity cards in a wallet and is placing the
wallet on top of the card reader, it will vary which card is read. The same
applies if the user has multiple key fobs chained together.
Users should present only one card (or key fob) at a time.
General considerations:
Security policies
Organizations’ security policies may allow users to only authenticate by
means of their provided ID card. Configuring the Nuance Mx Proximity
Reader to only support that particular protocol limits the risk of other
cards being used. Also the SafeCom solution can be configured to allow
only one ID code per user.
Self-service
Users are allowed to have multiple ID codes and they can register these
themselves at the device. This allows the users to authenticate with ID
cards that are not necessarily provided by administration.
ID cards with multiprotocol support
If the ID card support multiple protocols, then it will vary which protocol
will be returned. The card reader should be configured for selective card
reading so only one of the card’s supported protocols are enabled.
Existing solutions:
Existing SafeCom Proximity Readers are in use
Please refer to (2.2) for information on compatibility. It is good practice
to do some card testing (2.5) to get additional details.
ID code conversion
Existing filtercard.dll is installed to perform on-the-fly ID code
conversion.

2 Planning your SafeCom solution
D60829-07
10
2.2 Card reader compatibility
The Nuance Mx Proximity Series compatibility with existing SafeCom Proximity
Readers falls into 1 of 4 categories:
1
Protocol supported, card number format is the same
2
Protocol supported, card number format may differ
3
Protocol supported, card number format is different
4
Protocol not supported
Table 2 Card reader compatibility
SafeCom
Nuance Mx
Proximity Reader
Format
Format
Compatibility
SafeCom AWID Reader, [R]
Dec
Hex
3
SafeCom Casi-Rusco Reader, [R]
Dec
Hex
3
SafeCom Cotag Reader
Hex
Hex
3
SafeCom EM Reader, [E]
Hex
Hex
1
SafeCom EM Reader, [R]
Hex
Hex
2
SafeCom Felica Reader, [R]
Hex
Hex
2
SafeCom HID Prox Reader, [E]
Dec
Dec4
1
SafeCom HID Prox Reader, [R]
Dec
Dec
2
SafeCom HID Prox Reader 37 bit, [E]
Dec
Dec
1
SafeCom iCLASS Reader, [E]
Dec
Hex5
2
SafeCom iCLASS Reader, [R]
Dec
Hex
2
SafeCom Indala Reader, [R]
Dec
Hex
3
SafeCom Indala Reader, 29 bit [R]
Dec
Hex
3
SafeCom Inditag Reader, [E]
Hex
Hex
1
SafeCom IoProx Reader, [R]
Dec
Hex
3
SafeCom Legic Reader, [E]
Hex
Hex
1
SafeCom Mifare Reader, [E]
Hex
Hex
1
SafeCom Mifare Reader, [R]
Hex
Hex
2
SafeCom MultiISO Reader, [E]
Hex
Hex
1
SafeCom NexWatch Reader, [R]
Dec
Hex
3
SafeCom Nedap Reader
4
[E]: Elatec is the manufacturer of the proximity reader.
[R]: RFIdeas is the manufacturer of the proximity reader.
4
For HID Prox the ID code is written in decimal format. If the number of bits is 32 or
less the parity bits at the start and end are not written. If the number of bits is
between 33 and 44 the parity bit at the start is not written. Otherwise all bits are
written.
5
Only the UID is read. If the ID code consists of 32 or more bits there is a big likelihood,
that the ID code is different.

2 Planning your SafeCom solution
D60829-07
11
2.3 Supported protocols
Table 3 and Table 4 in this section listed the supported protocols for the low
and high frequency ranges.
Notes
1) UID only
2) UID only, read/write depending on demand
4) On request depending on demand
5) Only manchester f/64; sequence terminator off
6) Only emulation of 4100, 4102
7) Cotag is disabled by default
Table 3 Supported protocols (High frequency)
Nuance Mx
Proximity Reader
Nuance Mx Legic
Proximity Reader
13.56 MHz
IS014443A
Mifare Classic
✓
✓
2)
Mifare Mini
✓
✓
2)
Mifare DESFIRE EV1
✓
✓
Mifare Plus S,X
✓
2)
✓
2)
Mifare Pro X
✓
2)
✓
2)
Mifare SmartMX
✓
2)
✓
2)
Mifare Ultralight
✓
✓
Mifare Ultralight C
✓
✓
SLE44R35
✓
✓
2)
SLE66Rxx (my-d move)
✓
2)
✓
2)
Legic Prime
✓
Legic Advant
✓
1)
✓
Pay Pass
✓
2)
✓
2)
IS014443B
Calypso
✓
2)
CEPAS
✓
2)
Moneo
✓
2)
Pico Pass
✓
2)
✓
2)
SRI512, SRT512
✓
SRI4K, SRIX4K
✓
IS018092/ECMA-340
Sony Felica
✓
1)
✓
1)
NFC Forum Tag 2-4
✓
✓
IS015693
EM4x33
✓
2)
EM4x35
✓
2)
✓
2)
HID iClass
✓
1)
✓
1)
ICODE SLI
✓
✓
M24LR16/64
✓
✓
MB89R118/119
Pico Pass
✓
2)
✓
2)
Tag-it
✓
✓
SRF55Vxx (my-d vcinity)
✓
2)
✓
2)

2 Planning your SafeCom solution
D60829-07
12
Table 4 Supported protocols (Low frequency)
Nuance Mx
Proximity Reader
Nuance Mx Legic
Proximity Reader
125 kHz
AWID
✓
✓
Casi Rusco
✓
✓
Cotag
✓
7)
✓
7)
EM4100, 4102, 42006)
✓
✓
EM4150
EM4305
✓
4)
✓
4)
FDX-B
✓
✓
G-Prox
✓
✓
HID Prox
✓
✓
Hitag 1,2, S
✓
✓
Indala
✓
✓
IoProx
✓
✓
Keri
✓
✓
Miro
✓
✓
Nexwatch
✓
✓
Pyramid
✓
✓
Q5
T5557
✓
4)
✓
4)
T5567
✓
4)
✓
4)
TITAN
✓
4)
✓
4)
UNIQUE
✓
✓
ZOODIAC
✓
4)
✓
4)
2.4 Devices and reader types
Table 5 Devices and supported connections/emulations
Devices
USB
USB KBD6
Serial
Canon
USB
-
-
Fuji Xerox
-
-
Serial
HP, Chai
USB
-
-
HP, FS
USB
-
-
HP, DS
USB
-
-
HP Sx, DS
-
USB KBD
-
HP Pro, DS
USB7
-
-
Konica Minolta
USB8
-
-
Kyocera
-
USB KBD
-
Lexmark
USB
-
-
Ricoh
USB
-
-
Samsung
USB
-
-
Sharp
-
USB KBD
-
Xerox
-
USB KBD
-
Controller
USB
USB KBD
Serial
ID Controller
USB
USB KBD
-
6
Keyboard emulation.
7
HP printer firmware update required for HP Officejet Pro (planned for August 2014).
8
Konica Minolta only works with Konica Minolta supplied ID devices.

2 Planning your SafeCom solution
D60829-07
13
2.5 Card testing
2.5.1 Introduction
If you suspect, that the card to be tested is a multiprotocol card, it is always
good to present the card in two different ways to the reader:
Move the card slowly towards the reader.
Drop the card quickly and directly onto the top of the reader.
The reader will give two beeps if it supports two protocols.
The reader should be ready to read (the red LED is solid on) before the card is
presented. Presenting a multiprotocol card that support for example two
protocols will result two beeps.
If for example the card support both HID iClass and HID Prox. Dropping the card
quickly will result in two beeps and reading of both ID codes. Presenting the
card slowly will return only the HID Prox ID code (as it has a better reading
range).

2 Planning your SafeCom solution
D60829-07
14
2.5.2 Card test in SafeCom Administrator
Connect the reader to the USB port of a Windows computer running SafeCom
Administrator.
1. Open and login to SafeCom Administrator.
2. On the Actions menu click Options…
3. In the Options dialog click on the Card reader tab.
4. Click Test USB reader.
5. Present the card to the reader.
The ID code and its length is written.
2.5.3 Card test in Notepad (keyboard emulation)
Connect the reader to the USB port of a Windows computer.
1. Open Notepad.
2. Present the card to the reader.
The ID code is written if the reader is setup for keyboard emulation.
Otherwise it will not write anything.

2 Planning your SafeCom solution
D60829-07
15
2.5.4 Card test with tracer firmware loaded in reader
The Nuance Mx Proximity Reader can run firmware that will write out
information about the protocol of the presented card and the read ID code.
Section (3.7.3) describes how to use AppBlaster to load the tracer firmware.
Note: The written ID code for HID Prox cards is different from when SafeCom
software is loaded on the reader.
1. Open Notepad.
2. Present the card to the reader.
The ID code is written together with information about the protocol.
Presenting a multiprotocol card that support for example two protocols
will result in two lines being written and two beeps.
2.6 Hardware details
In most cases Nuance Mx Proximity Reader is the one with a USB male
connector, which is straight forward to connect to a computer to update or
configure using the AppBlaster application covered in Chapter 3. However,
special steps may be required if worknig with:
Nuance Mx Proximity Reader Module (2.6.2).
SafeCom Color Front-end (2.6.3).
Nuance Mx Proximity Reader, Serial (2.6.4).
2.6.1 Electrostatic Discharge (ESD) Handling Procedures
When handling print circuit boards and opening products you are cautioned to
follow Electrostatic Discharge (ESD) Handling Procedures. A Google search will
yield many excellent articles explaining these procedures.
Warning: Failure to follow these procedures could lead to immediate, or
longer term, permanent failure and/or damage to the products being handled.

2 Planning your SafeCom solution
D60829-07
16
2.6.2 HP hardware integration pocket (HIP)
Warning: Read (2.6.1) Electrostatic Discharge (ESD) Handling Procedures.
The Nuance Mx Module (print circuit board without casing) is fitted with a mini-
USB male connector.
The module need to be connected to a computer in order
to be firmware updated and/or configured. If the
computer does not have a mini-USB connector an
adaptor/cable is required. The adaptor/cable must have
female mini-USB and a male USB connector. See picture
of possible adaptor below.
Alternatively the Nuance SafeCom cable “E33 USB Cable, 45 cm” (p/n
SC0344020) can be used as it has a male USB connector at one end and a print
circuit board connector at the other end. The connector can fit one way only.
However this is more cumbersome, as it involves disconnecting and connecting
the cable to the connector on the print circuit board.
Note: It is recommended to label the unit to track, that it has been modified.

3 AppBlaster
D60829-07
17
2.6.3 SafeCom Color Front-ends
The SafeCom Color Front-end need to be opened and the Nuance Mx Proximity
Module inside need to be disconnected and connected temporarily with the
Nuance SafeCom cable “E33 USB Cable, 45 cm” (p/n SC0344020). Using the E33
cable’s male USB connector the module can now be connected directly to a
computer and be configured. After configurationat the original cable need to
be reconnected before the SafeCom Color Front-end is reassembled.
Warning: Read (2.6.1) Electrostatic Discharge (ESD) Handling Procedures.
Failure to follow these procedures could lead to immediate, or longer term,
permanent failure and/or damage to the SafeCom Color Front-end –failures
and damage which is not covered by warranty.
1. Place the SafeCom Color Front-end with top side down.
2. Loosen the 6 screws at the bottom (type is Philips #2).
3. Remove the bottom cover.
4. Gently disconnect the cable (Red arrow 1 on the picture).
5. Gently connect the Nuance SafeCom cable “E33 USB Cable, 45 cm” (p/n
SC0344020). The connector can fit one way only.
6. Connect the E33 cable’s male USB connector to a computer to configure
it (3.5). When done configuring it proceed to assemble the SafeCom Color
Front-end.
7. Gently disconnect the E33 cable from the module and connect the
original cable. The connector can fit one way only.
8. Put the the bottom cover back on and mount it with the 6 screews.
9. Connect the SafeCom Color Front-end to a SafeCom Controller and verify
that presenting a card results in the user holding the card is being
authenticated.
Note: It is recommended to label the unit to track, that it has been modified.

3 AppBlaster
D60829-07
18
2.6.4 Serial connected Nuance Mx Proximity Readers
The serial card readers can be connected to the computer via a SafeCom Serial
PC Cable (p/n SC0660010). The cable connects to the computer’s RS-232 DB9
connector for communication and 5 Volt power must be supplied via the PS2
keyboard pass-thru connector. The AppBlaster must be setup for serial
communucation (On the Settings tab select the appropriate Port under
Connection).
Alternatively the Nuance SafeCom cable “E33 USB Cable, 45 cm” (p/n
SC0344020) can be used as it has a male USB connector at one end and a print
circuit board connector at the other end.
However this is more cumbersome, as it involves opening the Nuance Mx
Proximity Reader and connecting the E33 cable to the connector on the print
circuit board. These are the involved steps:
Warning: Read (2.6.1) Electrostatic Discharge (ESD) Handling Procedures.
1. Place the Nuance Mx Proximity Reader with top side down.
2. Remove the four plastic feet in the corners to access the 4 screws.
3. Loosen the 4 screws.
4. Remove the bottom cover.
5. Loosen the 4 screws holding the reader module.
6. Gently disconnect the cable.
7. Gently connect the Nuance SafeCom cable “E33 USB Cable, 45 cm” (p/n
SC0344020). The connector can fit one way only.
8. Connect the E33 cable’s male USB connector to a computer to configure
it (3.5). When done configuring it proceed to assemble the Nuance Mx
Proximity Reader.
9. Gently disconnect the E33 cable from the module and connect the
original cable. The connector can fit one way only.
10. Mount the module with the 4 blank screws.
11. Put the the bottom cover back on and mount it with the 4 screews.
12. Connect the Nuance Mx Proximity Reader and verify that presenting a
card results in the user holding the card is being authenticated.
Note: It is recommended to label the unit to track, that it has been modified.

3 AppBlaster
D60829-07
19
2.6.5 Product label details
The product labels on the bottom of the Nuance Mx reader contains:
Part number (P/N SC0K… )
Manufacturer name (M/N TWN4…)
Serial number (S/N 5…)
The product labels for the Nuance Mx modules are located on the print circuit
board and in addition to the above contain an extra label on the main chip
(Mifare NFC or Legic NFC).
Table 6 Nuance Mx label details
Nuance Mx
Product label
Nuance Mx Proximity Reader, USB
Sales part number SC0970920
P/N
SC0K970920
M/N
TWN4 Mifare NFC
USB –P
S/N
52xxxxxx
Nuance Mx Proximity Reader, USB, KBD
Sales part number SC0970930
P/N
SC0K970930
M/N
TWN4 Mifare NFC
USB –P (KBD)
S/N
53xxxxxx
Nuance Mx Proximity Reader Module
Sales part number SC0970940
P/N
SC0K970940
M/N
TWN4 Mifare NFC
–P
S/N
54xxxxxx
Chip
Mifare NFC
Nuance Mx Proximity Reader, Serial
Sales part number SC0970910
P/N
SC0K970910
M/N
TWN4 Mifare NFC
–P –RS232
S/N
51xxxxxx
Table 7 Nuance Mx Legic label details
Nuance Mx Legic
Product label
Nuance Mx Legic Proximity Reader, USB
Sales part number SC0976920
P/N
SC0K976920
M/N
TWN4 Legic NFC
USB –P
S/N
56xxxxxx
Nuance Mx Legic Proximity Reader, USB, KBD
Sales part number SC0976930
P/N
SC0K976930
M/N
TWN4 Legic NFC
USB –P (KBD)
S/N
57xxxxxx
Nuance Mx Legic Proximity Reader Module
Sales part number SC0976940
P/N
SC0K976940
M/N
TWN4 Legic NFC
–P
S/N
58xxxxxx
Chip
Legic NFC
Nuance Mx Legic Proximity Reader, Serial
Sales part number SC0976910
P/N
SC0K976910
M/N
TWN4 Legic NFC
–P –RS232
S/N
55xxxxxx

3 AppBlaster
D60829-07
20
3AppBlaster
3.1 Introduction
The AppBlaster is a Windows application that is used to:
Configure, including enabling/disabling of protocols (3.5).
Update firmware (3.7).
3.2 Requirements
Windows XP SP2 or newer Windows OS (both 32-bit and 64-bit).
Microsoft .NET Framwork 3.5 SP1.
Please visit microsoft.com to download and install prior to the
installation.
2 GHz CPU and 2 GB RAM or greater.
200 MB disk space.
3.3 Install AppBlaster
1. Download the nuance_mx.zip file from the link supplied to you.
2. Extract the files to a folder.
The ZIP file contains these subfolders:
Driver –with Windows USB driver files used in (3.8).
Firmware –with *.bix firmware files.
Projects - with *.abp application files and *.bix firmware files.
Templates –with *.abp application files.
Tools –with required files needed for AppBlaster to function.
Template files provided:
Templates\TWN4_Sx149_SF100_Safecom_Standard.abp
Non-keyboard emulation application file used in (3.5).
Templates\TWN4_Kx149_SF100_Safecom_Standard.abp
Keyboard emulation application file used in (3.5).
Firmware files provided:
Firmware\TWN4_Sx149_SF100_Report_Safecom_Standard.bix
Non-keyboard emulation firmware file used in (3.7.1).
Firmware\TWN4_Kx149_SF100_Keyboard_Safecom_Standard.bix
Keyboard emulation firmware file used in (3.7.2).
Firmware\TWN4_Kx149_TRC105_Tracer.bix
Tracer firmware file used in (3.7.3).