SafeGuard 69200 Instructions for use

1
Safeguard® Truck Ramps
Model No.
Capacity
Product Size
Gross Weight/ Pc.
69200
20 Ton
45-5/8” x 13-1/2” x 9-1/2”
136.6 Lbs.
69201
20 Ton
45-5/8” x 18-1/4” x 9-1/2”
174 Lbs.
SAFETY & WARNING INFORMATION
Operating Instructions & Parts Manual
This is the safety notification
symbol. This symbol will notify you
of any potential injury hazards.
Please follow all instructions that
follow this symbol to avoid possible
injuries or death.
Indicates a hazardous
situation. If proper steps are
not followed, death or
serious injury could result.

2
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before using these truck ramps, be sure to read all content within this manual, ensuring that you
understand the operating procedures, maintenance requirements and all safety warnings.
The owner and/or operator shall have an understanding of the product, its operating characteristics, and
safety operating instructions before operating this device. Safety information shall be emphasized and
understood. If the operator is not fluent in English, the product and safety instructions shall be read to and
discussed with the operator in the operator’s native language by the purchaser/owner or his designee,
making sure that the operator comprehends their contents.
Actions to help prevent dangerous situations
Study, understand and follow all instructions before operating this device.
Use as a matched pair only.
Maximum load capacity per matched pair shall not exceed the rated capacity of the individual
ramp.
Use only on hard, level surfaces.
Lift only on areas of the vehicle as specified by the vehicle manufacturer.
No alterations shall be made to this product.
Use ramps to support one end of a vehicle only.
Center load on the ramp.
Never use truck ramps to support both ends or one side of a vehicle.
Failure to heed these warnings may result in serious personal injury / property damage.
Inspection
This device shall be inspected immediately if the device is believed to have been subjected to an
abnormal load or shock. It is recommended that this inspection be made by a manufacturer’s or
supplier’s authorized repair facility.
Owners and/or operators should be aware that repair of this equipment may require specialized
knowledge and facilities. It is recommended that an annual inspection of the product be made by a
manufacturer’s or supplier’s authorized repair facility and that any defective parts, decals, or safety
labels or signs be replaced with manufacturer’s or supplier’s specified parts.
Damaged Equipment and add-ons
Any truck ramp that appears to be damaged, is found to be worn or operates abnormally in any way will be
removed from service and destroyed immediately.
Alterations
Because of potential hazards associated with this type of equipment, no alterations shall be made to the
product.
Attachments and Adapters
Only attachments and/or adapters supplied by the manufacturer shall be used.
Setup
Prior to each use, visual inspection (See Pg.2 ) shall be made to the device by checking for abnormal
conditions, such as cracked welds, damaged, loose or missing parts.

3
Be sure to set the vehicle in park with the emergency brake on and wheels securely chocked.
Be sure that the vehicle and the truck ramps are on a hard, level surface.
Assembly
This product comes assembled in the box and should be ready for use.
Operation
Align the truck ramps in the center of the tires you wish to support.
Ensure that the ramps are directly in front of the desired tires to be lifted.
After steps one and two have been completed, ensure that the product handle is in the lowest
position and ensure that product is in full contact with the ground.
Rubber contacts located on the base of the product will prevent the ramps from shifting while the
vehicle is being loaded.
Have a second person, referred to the spotter here after, stand away from the vehicle being loaded
and advise the driver of their position while driving the vehicles on the ramp. It is the job of the
spotter to ensure that the vehicle is as centered on the ramps as possible.
Allow the vehicle to gradually climb up the ramps, using as little of accelerating force as possible.
Once the vehicle has reached the center of the top of the ramp, apply the brakes of the vehicle to
prevent the vehicle from falling off the front. The spotter should inform the driver when they have
reached this spot.
With the manual breaks applied, place the vehicle in neutral and apply the vehicles emergency
brake system. Only once the emergency brakes have been applied should you release the manual
brakes of the vehicle.
Once the emergency brakes have been activated, you can shut the vehicle off and the driver can
safely step out of the vehicle. Please note that there will now be a drop off once someone exits the
vehicle and they should take extra precaution when exiting the vehicle.
Wheel chock the wheels of the vehicle that are not being supported by the ramps for additional
safety.
Once secured, give the supported vehicle a firm shake and ensure that the ramps and the vehicle
are all stable.
Finally, ensure that no damage has happened to the ramps while the vehicle was being loaded. If
there is any structural damage noticed, you should remove the vehicle from the ramps and
discontinue use until a new set of truck ramps can be acquired or the existing set can be repaired
by a verified repair center.
To lower a vehicle, use a spotter once more to assist the driver off of the ramps. Ensure that all
persons and property are safely away from the vehicle before you begin to offload. Remove all
wheels chocks before entering the vehicle
Once in the vehicle, turn the vehicle on and apply the manual brake system. Release the
emergency brake and shift the vehicle into reverse. Once in gear, slowly release the manual brake
system and slowly and in a controlled manner back the vehicle off of the truck ramps using the
spotter to keep the vehicle aligned during the off load process.
Once the vehicle is clear of the area, it is safe to dolly the ramps by lifting their handles to a storage
area.
Maintenance
Inspect each stand before use. Ensure all parts move freely. If rust appears, sand away the rust area and
cover with appropriate utility paint.

4
Item
Part Number
Description
Qt’y
1
XP20.1
Handle Assembly
1
2
XP20-2
Wheel Assembly
2
* Items not identified by part number are not available for replacement.
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from your purchase date, THA Hydraulics will repair or replace (at its
option), without charge, your THA product if it was purchased new and the product has failed due to a defect
in material or workmanship which you experienced during normal use of the product. This limited warranty is
your exclusive remedy.
To access the benefits of this warranty, contact THA at 1-844-364-9922 for confirmation that this
warranty applies. Thereafter, you may be advised to return the product under warranty, freight prepaid, to
the THA service department.
If this THA product is altered, abused, misused, modified or undergoes service by an unauthorized
technician, your warranty will be void. We are not responsible for damage to ornamental designs you place
on this THA product and such ornamentation should not cover any warnings or instructions or they may void
the warranty. This warranty does not cover scratches, superficial dents and other abrasions to the paint
finish that occur under normal use.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defective product as described
above.
(2) THA is not liable for any incidental damages, including but not limited to, lost profits and
unforeseeable consequences.
(3) The repair and replacement of this product under the express limited warranty described above is
your exclusive remedy and is provided in lieu of all other warranties, express or implied. All other
warranties, including implied warranties and warranties of merchantability or fitness for a particular
purpose are disclaimed and, if disclaimer is prohibited, these warranties are limited to one year from
your date of purchase of this product.
Some states’ laws do not allow limited durations on certain implied warranties and some states’ laws do not
allow limitations on incidental or consequential damages. You should consult the law in your state to
determine how your rights may vary.
THA Hydraulics
12200 N.W. Ambassador Drive, Suite 202
Kansas City, MO 64163
Toll Free Service Number 1-844-364-9922
Printed In China