Safety Vision 60-220003 User manual

60-220003
USER GUIDE

Important Notices
Title: 60-220003 User Guide
Document Version 1
Revision 0
Safety Vision attempts to provide information contained in
this manual based on the latest product information available
at the time of publication. However, because of Safety Vision’s
policy of continual product improvement, Safety Vision
reserves the right to amend the information in this document
at any time without prior notice.
This material is condential and the property of Safety Vision.
It is shared with your company for the sole purpose of helping
you with the operation of the described equipment.
Safety Vision makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties
of merchantability and tness for a particular purpose. Safety
Vision shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
Safety Vision expressly disclaims all responsibility and liability
for the installation, use, performance, maintenance, and
support of third-party products. Customers are advised to
make their independent evaluation of such products.
No part of this document may be photocopied, reproduced,
or translated to another language without the prior written
consent of Safety Vision.
Safety Vision® is a registered trademark of Safety Vision, LLC. All
other products or name brands mentioned in this document are
trademarks of their respective
owners. For more information about Safety Vision and its
products, go to www.safetyvision.com or call 800-880-8855.
60220003 USER GUIDE

Table of Contents
Components 2
Installation 3
Conguration 4
Connecting 4
Audio Adjustment 5
Live View and Image Adjustment 6
Appendix A: Specications 7
Appendix B: Dimensions 8
60220003 USER GUIDE

Components
Exterior
1 - Dome - Shields the camera lens while providing a wide
viewing angle.
2 - Unit Cover - Protects the camera module from
environmental hazards.
Interior
3 - Camera Lens - Captures images.
4 - IR Illuminators - Provide clear images in low light
conditions.
5 - Gimbal - Adjusts the camera lens angle for the optimal
eld of view.
260-220003 USER GUIDE

Installation
Use the following procedure to install the 60-220003:
1. Clean the area where the camera is to be installed.
2. Apply the included adhesive template, or use it to mark two
screw holes and cable hole in the desired mounting location.
3. Use a hole saw or appropriate drill bit to drill a 1.181 inch hole
where marked for the cable and apply a grommet.
4. Drill two screw holes where marked if not using self-tapping
screws.
5. Thread the cable through the hole and secure the camera
base to the mounting surface. Do not use larger than a size #6
fastener to avoid damage to the camera housing.
6. Connect the 60-220003 to one of the camera inputs on front
of the NVR.
7. Using a laptop, access the camera’s live view as described in
the Live View and Image Adjustment section.
8. Use a small Phillips head screw driver to loosen the security
screws on the camera gimbal to adjust the camera angle to
the desired eld of view. Once completed, tighten the security
screws in place.
9. Secure the enclosure over the camera and base with the
supplied tamper-resistant screws with a size T10 TORX™
wrench. Ensure the urethane washers are in place to ensure a
waterproof seal.
10. Apply silicone sealant around the base to ensure a waterproof
seal.
11. Refer to the NVR User Guide to properly congure the camera
parameters.
12. (Optional) Connect the co-axial cable to an external monitor
to display a live video feed from the camera without the use of
a decoder.
Warnings:
• To reduce the risk of electrical shock,
disconnect the battery from the electrical
system of the vehicle before starting the
installation.
• Before inserting fasteners into the
mounting surface, ensure that the
underside of the mounting surface is clear
of equipment that might be damaged by
the screws.
60-220003 USER GUIDE 3

Conguration
The 60-220003 can be congured through the on-board web
interface, which must be accessed with a PC and web browser.
The interface can be accessed through a RoadRecorder®series
NVR.
Connecting
Use the following procedure to access the 60-220003’s
conguration web server while connected to a RoadRecorder
NVR:
1. Connect the PC to the NVR’s Ethernet LAN RJ-45 port
with a standard Ethernet cable.
2. Ensure the NVR and PC are receiving power and have
started up.
3. Open the Internet Protocol (TCP/IP) Properties window
for the LAN connection you are using.
In Windows, open Network Connections. Right-click the LAN
connection and select Properties. In the list of items, select
Internet Protocol (TCP/IP) and then click Properties.
4. Select the Use the following IP address option.
5. Enter 192.168.8.80 in the IP address eld.
6. Enter 255.255.0.0 in the Subnet mask eld.
This eld normally defaults to 255.255.255.0. Ensure the
correct 255.255.0.0 subnet is
entered.
7. Leave all other elds blank.
8. Click OK on the Internet Protocol
(TCP/IP) Properties window and
then click OK on the Local Area
Connection Properties window.
Your PC’s IP address and subnet mask
are now congured.
9. On a web browser, navigate to
192.168.8.70.
10. Enter the user name and password
and login.
11. Click the Live View tab.
12. Select the camera(s) you want to
view and/or congure and click
View Selected Device(s).
13. After a short period the selected
cameras display. Adjust the
camera image, or click on the
camera name at the bottom of the
image to access the conguration
page.
460-220003 USER GUIDE

Audio Adjustment
To adjust the stream, rst click
Streaming at the top of the
conguration page, then Audio
on the menu on the left.
Certain installations may cause
undesirable audio noise. In some
cases, adjusting the Input gain
eld down alleviates these issues.
After adjusting this eld, click
Save.
If audio problems persist, contact
Safety Vision Technical Support.
Safety Vision does not recommend adjusting
settings other than those described in this
User Guide without the advice of Safety Vision
Technical Support.
60-220003 USER GUIDE 5

Live View and Image Adjustment
After the 60-220003 is installed, the
image’s eld of view can also be
conrmed with the VLC Media Player
application.
VLC Media Player is available from the
Video LAN Organization for free.
Use the following procedure to view a
live image from the 60-220003 using VLC
Media Player:
1. Connect the PC to the NVR’s
Ethernet LAN RJ-45 port with
a standard Ethernet cable and
congure it as described in steps 1
- 8 of the Connecting procedure on
page 4.
2. On the PC, open the VLC Media
Player application.
3. In VLC Media Player, select Open
Network Stream... from the Media
menu.
The Open Media window appears.
4. In the Network URL eld, enter
rtsp://192.168.8.70:8XX/h264_2,
where XX is the NVR port the 60-220003 is connected to.
For example, if you want to view the 60-220003 connected to
port 8, you would enter rtsp://192.168.8.70:808/h264_2.
5. Click Play.
The VLC Media Player appears displaying a live image
of the camera selected.
With the live view displayed, you can adjust the image’s
eld of view by adjusting the gimbal. Remove the
enclosure from the base plate. Using an appropriate
screwdriver, loosen the screws on the gimbal and
carefully move the camera unit until satised. Retighten
the screws on the gimbal and replace the enclosure.
660-220003 USER GUIDE

SPECIFICATIONS
Image Sensor 1/2.8" Sony Progressive CMOS
Eective Pixels 2048(H) x 1536(V)
Minimum Illumiation Board 3.6 mm - 0.2 lux (Color) / 0.02 lux (B/W)
Board 2.8 mm / Vari-focal 3~6 mm - TBD
Lens Board / Vari-focal Lens
Focal Length Board - 2.8 mm / 3.6 mm
Vari-focal - 3~6 mm
FOV Board 3.6 mm - 75.3°
Board 2.8 mm - 94.36°
Vari-focal 3~6 mm - 100.8°
Interface RJ-45, 10/100mbps
Video Compression H.264 (MPEG-4 Part 10/AVC) / MJPEG
Video Resolution H.264- 2048 x 1536 (3M) / Full HD 1080P /
SXGA / HD 720P / XGA / SVGA / D1 / VGA /
CIF
MJPEG- Full HD 1080P / SXGA / HD 720P /
XGA / SVGA / D1 / VGA / CIF
Frame Rate Dual Streams : 1080p (30/25 fps) + D1 (30/25
fps)
Protocol ARP, IPv4/v6, TCP/IP, UDP, RTP, RTSP, HTTP,
HTTPS, ICMP, FTP, SMTP, DHCP, PPPoE, UPnP,
IGMP, SNMP, QoS, ONVIF
IR Yes, 24 LEDs
Power Source PoE
Operating Temperature -10°C to approx 50°C
Dimensions (w × h)4.6 in. × 3.36 in.
Appendix A: Specications
60-220003 USER GUIDE 7

Appendix B: Dimensions
860-220003 USER GUIDE