Safety Vision SV-830 User manual
Main: 713.896.6600
Toll Free: 800.880.8855 www.safetyvision.com
6100 W. Sam Houston Pkwy. N.
Houston, TX 77041-5113
Copyright © 2015 Safety Vision, LLC All Rights Reserved.
830 SERIES QUICK INSTALLATION GUIDE GUIDE
Installation Guide
The customer should thoroughly read this guide before
operating this product.
Safety Precautions
• To reduce the risk of electrical shock, disconnect the battery
from the electrical system of the vehicle before starting the
installation.
• Before inserting fasteners into the mounting surface, ensure
that the underside of the mounting surface is clear of
equipment that might be damaged by the screws.
Installation
1. Use the selector switch located on the small printed circuit
board (PCB) to select if the red LED will blink or remain o
when the camera receives power.
2. Using the base as a template, tap or otherwise mark four
screw holes in the desired mounting location.
3. Drill a 0.875 inch hole in the approximate center of the four
marked screw holes to thread the cables through.
4. Thread the cables through the drilled hole and use self-
tapping screws or rivets to secure the base to the desired
mounting location.
5. Connect the cables to the MDVR unit.
6. Loosen the security screws on the camera gimbal to adjust
the camera angle to the desired eld of view. This might
require the use of an optional external monitor connected to
the MDVR unit. Once completed, tighten the security screws
in place.
7. Connect the LED/Microphone cable in the enclosure to the
PCB on the base.
8. Secure the enclosure over the camera and base with the
four included tamper-resistant screws with a size T10 TORX™
screwdriver.
Notice to Users: This document is condential and contains proprietary informa-
tion belonging to Safety Vision, L.P. This document and the information contained
herein cannot be distributed, communicated, reproduced, altered, or dissemi-
nated by any means, in whole or in part, without the express written consent of
Safety Vision, L.P. Possession of this document constitutes the user’s acceptance
of these nondisclosure covenants. The information in this document is believed
to be accurate in all respects. However, Safety Vision cannot assume responsibility
for any consequences resulting from the use thereof. The information contained
herein is subject to change without notice. Revisions or new editions to this publi-
cation may be issued to incorporate such changes.
Dome Enclosure
Wedge Enclosure
The SV-830 dome and wedge cameras are compact mobile-rated cameras that mount easily in a variety of
orientations. High-intensity IRs and 420 TV lines of resolution allow for high quality images in multiple light conditions.
Use the following procedure to install the SV-830 Series Day/Night Camera.
Main: 713.896.6600
Toll Free: 800.880.8855 www.safetyvision.com
6100 W. Sam Houston Pkwy. N.
Houston, TX 77041-5113
Copyright © 2015 Safety Vision, LLC All Rights Reserved.
830 SERIES QUICK INSTALLATION GUIDE GUIDE
Limited Warranty
LIMITED 1-YEAR NEW PRODUCT WARRANTY
Safety Vision, LLC (“SV”) makes the following limited warranty,
which is eective at the time of the original end-user purchase.
Note - Optional warranty products are available for all SV products
and may be purchased at the time of the original end-user purchase
or any time during the original Limited 1-Year New Product Warranty
period.
SV warrants this product against defects in materials for a period
of 1 year after the date of purchase. During this period, SV will
repair or replace a defective product or part without charge to
the customer. The customer must send the defective product
or part to SV or an authorized SV dealer. The customer must pay
for all transportation and insurance charges for sending the unit
to be repaired. SV’s total liability is limited to the original product
cost.
Installation Guide
The customer should thoroughly read this guide before
operating this product.
Customer’s Responsibility
The above warranty is subject to the following conditions:
• Customer must notify SV within 10 days of discovering the
defective product or part and provide a description of the
defect and complete information about the manner of its
discovery.
• All warranty servicing of this product must be performed by
SV or an authorized servicing agent.
• Warranty extends only to defects in materials as limited
above. Warranty does not extend to any product or part
that has been lost or discarded by the customer; to damage
to products or parts caused by misuse, accident, improper
installation, improper maintenance, or use in violation of
instructions furnished with the product; to units that have
been altered or modied without authorization of SV; to
damage to products or parts thereof that have had the serial
number removed, altered, defaced, or rendered illegible; or
to any failure of the product to function caused by burglary,
re, ood, war, riot, civil commotion, Acts of God, or any other
condition beyond the control of SV.
Obtaining Warranty Service
To obtain warranty service, the customer must contact the SV
Service and Warranty Manager at 713.896.6600 or 800.880.8855
to report a defective product. (The customer must report the
model number and serial number if available.) The Service and
Warranty Manager will assist in troubleshooting the problem
and, if necessary, issue a return material authorization (RMA)
number. The customer must include this number on the
outside of each package shipped to SV.
Packing and Shipping Instructions
When a product requires service, only the aected component
must be returned. The customer must use proper packing
material to ensure against damage during shipping. Any
shipping damage caused by improper packing is not covered
under this warranty. In addition, the customer must include a
return material authorization (RMA) number on the outside of
each package shipped to SV and a letter explaining the defect
with the product.
How to Reach Us
If you have exhausted the information in this document yet
require further assistance or information, please contact Safety
Vision toll-free at 1-800-880-8855 or send an e-mail message
requesting assistance to: email@safetyvision.com.
SPECIFICATIONS
Image Sensor Standard: 1/4-inch color Sony® CCD
Standard (CMOS): 1/4-inch color Micron® CMOS
High Resolution: 1/3-inch color Sony® CCD
Signal Format NTSC Standard / PAL
Lens Focal Length 2.6 / 4 / 6 / 8 mm
Minimum Illumination 0 Lux (0.5 Lux CMOS)
IR Illumination High-intensity IRs
Synchronization Internal
Resolution Standard: 500 TV Lines
High Resolution: 600 TV Lines
Picture Elements
NTSC/PAL
Standard: 510 (H) x 492 (V) / 500 (H) x 582 (V)
Standard (CMOS): 656 (H) x 492 (V)
High Resolution: 768 (H) x 494 (V) / 768 (H) x 582 (V)
Signal-to-Noise Ratio > 48 dB
IP Rating Standard / High Resolution (Dome): IP65
Standard / High Resolution (Wedge): IP68
Power Supply 12V DC
Power Consumption 2.5W
Operating Temperature -22°F ~ 158°F (-30°C ~ 70°C)
Audio 2V Peak to Peak at 94 dBA
Other Safety Vision Security Camera manuals
