Safety Vision SV-500A User manual

Main: 713.896.6600
Toll Free: 800.880.8855 www.safetyvision.com
6100 W. Sam Houston Pkwy. N.
Houston, TX 77041-5113
Copyright © 2015 Safety Vision, LLC All Rights Reserved.
500A/620A QUICK INSTALLATION GUIDE GUIDE
Installation Guide
The customer should thoroughly read this guide before
operating this product.
Safety Precautions
• To reduce the risk of electrical shock, disconnect the battery
from the electrical system of the vehicle before starting the
installation.
• Before inserting fasteners into the mounting surface, ensure
that the underside of the mounting surface is clear of
equipment that might be damaged by the screws.
Installation
1. Use a at-head screwdriver to insert the magnetic screw in
either the NOR (Normal) or MIR (Mirror) hole on the rear of
the camera housing to specify how the image is displayed
on a monitor.
Normal is typically used when the camera is mounted facing
forward, and Mirror is typically used when the camera is
mounted facing backward.
2. Using the base as a template, tap or otherwise mark four
screw holes in the desired mounting location.
3. Drill a 0.875 inch hole near the four marked screw holes to
thread the camera cable through.
4. Thread the cable through the drilled hole and use self-
tapping screws or rivets to secure the base to the desired
mounting location.
5. Connect the cable to an appropriate extension cable,
connected to the collision avoidance system control box.
6. Insert the camera, and then the visor, into the camera base
and secure them with the four provided screws loosely.
7. Using the collision avoidance system monitor, adjust the
camera and visor at an angle that produces the desired
image and tighten the four screws securely with a 3 mm hex-
head screwdriver.
Notice to Users: This document is condential and contains proprietary
information belonging to Safety Vision, LLC. This document and the information
contained herein cannot be distributed, communicated, reproduced, altered,
or disseminated by any means, in whole or in part, without the express written
consent of Safety Vision, LLC. Possession of this document constitutes the user’s
acceptance of these nondisclosure covenants. The information in this document
is believed to be accurate in all respects. However, Safety Vision cannot assume
responsibility for any consequences resulting from the use thereof. The informa-
tion contained herein is subject to change without notice. Revisions or new
editions to this publication may be issued to incorporate such changes.
Base Installation
Camera and Visor Adjustment
The SV-500A/620A collision avoidance cameras are compact mobile-rated cameras that mount easily in a variety of
orientations. The camera’s infrared illuminators automatically activate as needed providing you with optimal image
quality. Use the following procedure to install the SV-500A/620A Day/Night Cameras.

Main: 713.896.6600
Toll Free: 800.880.8855 www.safetyvision.com
6100 W. Sam Houston Pkwy. N.
Houston, TX 77041-5113
Copyright © 2015 Safety Vision, LLC All Rights Reserved.
500A/620A QUICK INSTALLATION GUIDE GUIDE
Limited Warranty
LIMITED 1-YEAR NEW PRODUCT WARRANTY
Safety Vision, LLC (“SV”) makes the following limited warranty,
which is eective at the time of the original end-user purchase.
Note - Optional warranty products are available for all SV products
and may be purchased at the time of the original end-user purchase
or any time during the original Limited 1-Year New Product Warranty
period.
SV warrants this product against defects in materials for a period
of 1 year after the date of purchase. During this period, SV will
repair or replace a defective product or part without charge to
the customer. The customer must send the defective product
or part to SV or an authorized SV dealer. The customer must pay
for all transportation and insurance charges for sending the unit
to be repaired. SV’s total liability is limited to the original product
cost.
Installation Guide
The customer should thoroughly read this guide before
operating this product.
Customer’s Responsibility
The above warranty is subject to the following conditions:
• Customer must notify SV within 10 days of discovering the
defective product or part and provide a description of the
defect and complete information about the manner of its
discovery.
• All warranty servicing of this product must be performed by
SV or an authorized servicing agent.
• Warranty extends only to defects in materials as limited
above. Warranty does not extend to any product or part
that has been lost or discarded by the customer; to damage
to products or parts caused by misuse, accident, improper
installation, improper maintenance, or use in violation of
instructions furnished with the product; to units that have
been altered or modied without authorization of SV; to
damage to products or parts thereof that have had the serial
number removed, altered, defaced, or rendered illegible; or
to any failure of the product to function caused by burglary,
re, ood, war, riot, civil commotion, Acts of God, or any other
condition beyond the control of SV.
Obtaining Warranty Service
To obtain warranty service, the customer must contact the SV
Service and Warranty Manager at 713.896.6600 or 800.880.8855
to report a defective product. (The customer must report the
model number and serial number if available.) The Service and
Warranty Manager will assist in troubleshooting the problem
and, if necessary, issue a return material authorization (RMA)
number. The customer must include this number on the
outside of each package shipped to SV.
Packing and Shipping Instructions
When a product requires service, only the aected component
must be returned. The customer must use proper packing
material to ensure against damage during shipping. Any
shipping damage caused by improper packing is not covered
under this warranty. In addition, the customer must include a
return material authorization (RMA) number on the outside of
each package shipped to SV and a letter explaining the defect
with the product.
How to Reach Us
If you have exhausted the information in this document yet
require further assistance or information, please contact Safety
Vision toll-free at 1-800-880-8855 or send an e-mail message
requesting assistance to: [e-mail].
SPECIFICATIONS
SV-620A (Color) and
SV-500A (Black and White) Cameras
Image Sensor 1/3-inch Interline transfer CCD
Signal Format NTSC
Lens Focal Length 2.5 mm
Synchronization Internal
Horizontal Resolution 480 TV lines (color) / 380 TV lines (black and white)
Minimum Illumination 0 Lux
Signal-to-Noise Ratio > 50 dB (color) > 47 dB (black and white)
Power Requirement 12 VDC
Operating Temperature -22°F ~ 122°F
Dimensions (w x h x d) 2.7 in. × 1.7 in. × 2.0 in.