Safety Vision SV-CLCD56B User manual

SV-CLCD56B/70B Quick Installation Guide March 007
Copyright © 007 Safety Vision, L.P.
Safety Vision and the Safety Vision logo are trademarks of Safety Vision, L.P.
Notice to Users: This document is confidential and contains proprietary information belonging to Safety Vision, L.P. This document and the information
contained herein cannot be distributed, communicated, reproduced, altered, or disseminated by any means, in whole or in part, without the express
written consent of Safety Vision, L.P. Possession of this document constitutes the user’s acceptance of these nondisclosure covenants. The information
in this document is believed to be accurate in all respects. However, Safety Vision cannot assume responsibility for any consequences resulting from the
use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to
incorporate such changes.
Safety Vision ▪ 6100 West Sam Houston Parkway North ▪ Houston, Te as 77041 ▪ USA
SV-CLCD56B_70B QIG Ver.1.0.doc 1
Safety Vision SV-CLCD56B
Safety Vision SV-CLCD70B
Color TFT LCD Collision Avoidance System
Quick Installation Guide
Overview
The Safety Vision SV-CLCD56B and SV-CLCD70B Color
TFT LCD Collision Avoidance Systems are designed for
rugged, mobile environments and turn on automatically
when the vehicle transmission is in reverse gear. Each
system includes a monitor, camera, and control box. (The
SV-CLCD56B system includes a 5.6-inch monitor, and
the and SV-CLCD70B system includes a 7.0-inch
monitor.) The system monitor has an integrated speaker,
and the system camera has an integrated microphone,
permitting the driver to both see and hear activity within
the camera’s range. Although two cameras can be
connected to the SV-CLCD56B/70B system, only one
camera is provided with the system.
Components of the SV-CLCD56B/70B system include:
 Safety Vision SV-LCD56B or SV-LCD70B Monitor,
which features:
 Either a 5.6-inch or 7-0-inch TFT LCD screen
 Wide field of view
 Integrated speaker
 Safety Vision SV-6 5B-KIT, which includes the
camera (Part Number SV-6 5B) and a 65-foot
extension cable (Part Number SV-5 3B) and has the
following features:
 Rugged, water-resistant housing
 CCD image sensor for improved image quality
 Wide field of view (135° diagonal, 108° horizontal)
 LEDs that generate infrared light for improved
image quality in low-light situations
 Integrated microphone
 Safety Vision SV-CBB-56-70 Control Box, which
provides DC power to the monitor and camera(s) and
features:
 audio/video inputs
 1 audio/video output
Important Safety Precautions
Install and operate the SV-CLCD56B/70B system with
the following safety precautions in mind:
 The ground (black) wire of the control box system
power cable must be connected directly to the vehicle
chassis.
 Use only the correct voltage (1 to 4 VDC).
 To reduce the risk of electrical shock, disconnect the
battery from the electrical system of the vehicle before
starting the installation.
 Do not expose the monitor or control box to water or
other liquids.
 To avoid the risk of electric shock, do not disassemble
the system components, and keep cables away from
sharp objects.
 Do not block the ventilation holes in the monitor
housing.
 This system is designed to assist the vehicle driver
with rear vision only. Do not attempt to view the
monitor while driving forward. Do not attempt to
operate the control box while driving.
 Select inconspicuous cable routes that do not interfere
with normal driver or passenger mobility.

SV-CLCD56B/70B Quick Installation Guide March 007
SV-CLCD56B_70B QIG Ver.1.0.doc 2
Supplied Hardware
The following hardware is supplied for installation with
each SV-CLCD56B/70B system:
Hardware Item Quantity
SV-LCD56B/70B Monitor 1
Monitor Cable 1
Monitor Mounting Bracket 1
Monitor Screw Kit 1
SV-CBB-56-70 Control Box 1
Control Box System Power Cable 1
Control Box Screw Kit 1
SV-6 5B Camera 1
Camera Extension Cable (65-foot) 1
Camera Sun Visor 1
Camera Mounting Bracket 1
Camera Screw Kit 1
System Components
SV-LCD56B/70B Monitor
A POWER LED—indicates that the monitor has power
B DAY/NIGHT SENSOR—senses available light and
adjusts monitor brightness accordingly
C
MENU BUTTON—initiates display of onscreen user
controls for image contrast and brightness and
speaker volume
D
+ BUTTON—UP button—increases the value for
Setup menu items, such as Volume
E
– BUTTON—DOWN button—decreases the value
for Setup menu items, such as Volume
F
POWER/CAM SELECT BUTTON—when pressed
and held for 1 second, turns the monitor ON or OFF;
when pressed briefly, switches image input)
G
NORMAL/MIRROR SWITCH—switches image
display to Normal or Reverse (as it would appear in
a rear-view mirror)
H
MONITOR CABLE—receives power and camera
images from the control box
I BRACKET SLOT—accepts the adjustable mounting
bracket
SV-625B Camera
A Infrared LEDs—generate light to compensate for
low-light situations
B
INTEGRATED MICROPHONE

SV-CLCD56B/70B Quick Installation Guide March 007
SV-CLCD56B_70B QIG Ver.1.0.doc 3
SV-CBB-56-70 Control Bo
A
MAX-MIN AUTO TIME KNOB—used with an
optional remote control device to set camera dwell
time in Scan mode (not typically used in
SV-CLCD56B/70B system installations)
B
AUX OUT—accepts the connector of an optional
audio/video output device (yellow/video, red/right,
white/left)
C
AUX IN—accepts the connector of an optional
audio/video input device (yellow/video, red/right,
white/left)
D
POWER OUT—provides power to an optional
peripheral device
E REMOCON—accepts the connector of an optional
remote control device
F MONITOR—accepts the connector of the monitor
cable
G
MIR/NOR SWITCHES—control the mirror/normal
image setting for the corresponding cameras
H
CAM2—accepts the cable connector for an optional
second camera and supplies power to the camera
I CAM1—accepts the connector for the supplied
camera extension cable and supplies power to the
camera
J POWER IN—accepts the barrel-type connector of
an optional power cable (not typically used in
SV-CLCD56B/70B system installations)
K
POWER IN—accepts the 4-pin Molex connector of
the control box system power cable
Optional Components
Optional components for the SV-CLCD56B/70B system
include a remote control device (Part Number SV-LCDB-
CP) for the monitor. In addition, devices other than the
components supplied with the SV-CLCD56B/70B system
(such as an additional camera) can be connected to the
system.
Typical Installation
 SV-LCD56B/70B Monitor
1. Select a mounting surface for the monitor, which can
be mounted overhead or elsewhere in the vehicle
cabin (including on the floor or console).
The mounting surface should:
 Be level, waterproof, ventilated adequately, and
capable of supporting the weight of the monitor and
mounting bracket
 Not be close to a vehicle speaker (to prevent
interference from the speaker’s magnetic field)
 Not be extremely hot or humid
. Affix the monitor bracket to the mounting surface with
the supplied screws.
 Installing the Monitor Bracket
3. Position the monitor in the monitor mounting bracket,
adjust the angle as necessary, and tighten the handle
screw.
 Installing the Monitor in the Bracket

SV-CLCD56B/70B Quick Installation Guide March 007
SV-CLCD56B_70B QIG Ver.1.0.doc 4
 SV-625B Camera
1. Select an appropriate mounting location for the
camera, which should be mounted on a solid, flat
surface at the highest possible point on the vehicle.
. With the provided hardware, affix the camera
mounting bracket to the mounting surface, and secure
the camera and sun visor in the bracket.
 Installing the Camera
3. Connect the male connector of the camera pigtail to
the female connector of the provided 65-foot extension
cable. Align the arrows on both cable connectors, and
then hand-tighten, as follows:
 Connecting the Camera Pigtail to the Extension Cable
 SV-CBB-56-70 Control Bo
1. Select a discreet location for the control box, such as
under the vehicle dashboard. Use the provided screws
to secure the control box to the mounting surface.
 Installing the Control Box
. Route the camera extension cable to the control box
and insert the connector in the CAM1 receptacle.
3. Route the monitor cable to the control box and insert
the connector in the MONITOR receptacle
4. Route the control box system power cable from the
control box to the vehicle battery, and connect the
unterminated wires as follows:
Wire Color Vehicle Location
Red Vehicle wire that has 1 VDC when
the vehicle ignition is on
Black
(Ground)
Vehicle chassis
Green
(Trigger 1)
Vehicle wire that has 1 VDC when
the vehicle transmission is in reverse
gear (typically the wire for the backup
lights). (When this wire has 1 VDC,
the monitor receives input from
Camera 1.)
White
(Trigger )
(Optional)
Vehicle wire that has 1 VDC when a
separate event (such as activating a
turn signal) occurs. (When this wire
has 1 VDC, the monitor receives
input from an optional Camera .
Camera 1 input takes priority over
Camera input.)
5. Insert the 4-pin Molex connector of the system power
cable into the POWER IN receptacle on the rear panel
of the control box.

SV-CLCD56B/70B Quick Installation Guide March 007
SV-CLCD56B_70B QIG Ver.1.0.doc 5
System Operation
 Initial Setup
To initiate display of the main menu, press the MENU
button on the front panel of the monitor. Use the UP and
DOWN buttons to increase and decrease values for
menu items.
NOTE:
After several seconds of inactivity, the menu is no
longer displayed, and the MENU button must be
pressed again to initiate display of the main menu
again.
Menu items can be changed as follows:
Menu Item Function
CONTRAST Adjusts the contrast level between dark
and light images
BRIGHT Adjusts the brightness intensity level
VOLUME Adjusts the volume of the integrated
speaker
 System Power
In typical installations, the system is placed into Standby
mode automatically when the sensor wire for the vehicle
ignition is activated, and the monitor automatically
displays camera input when the sensor wire for the
vehicle backup lights is activated. The system can also
be powered ON and OFF manually with the POWER
button on the front panel of the monitor.
 Cleaning
Turn the system off and disconnect components from
power before cleaning. Use a damp cloth for cleaning. Do
not use harsh cleaners.
Specifications
 SV-LCD56B/70B Monitor
Item Specification
LCD Panel Size 5.6-inch or 7.0-inch (diagonal)
Video System NTSC standard signal
Power Input 1 VDC (with control box 1 / 4 VDC)
Power Consumption Maximum 5 watts
Sync System Internal
Resolution 336,960 pixels
Power Connector 4-pin wire S-video connector
Speaker Impedance 16 ohms, 0.5 watt maximum
Impact Rating 4 G
LCD Profile Wide-
Screen Ratio
5.6-inch: 4:3
7.0-inch: 16:9
Response Time 30 ms (at 5°C)
View Angle (CR>10) 40/65/65/65 (up/down/left/right)
Field of View 135° diagonal, 108° horizontal
Brightness 500 cd/m
Contrast Ratio 300:1
Automatic Brightness
Control
Light sensor, Day/Night switch
On-Screen Display
Controls
Brightness, Contrast, Volume Color,
Languages
Operating Temperature 5°F to 149°F (-15°C to 65°C)
Storage Temperature -13°F to 185°F (- 5°C to 85°C)
Weight 5.6-inch: 0.75 pounds (0.34 kg)
7.0-inch: 0.88 pounds (0.40 kg)
Dimensions
Width x Height x Depth
5.6-inch: 6.5 x 4.5 x 1.1 inch
(165 x 115 x 9 mm)
7.0-inch: 7.9 x 4.5 x 1.1 inch
( 00 x 115 x 9 mm)
Supplied Accessories  Adjustable mounting bracket
 Extension cable
 Screw kit
 SV-625B Camera
Item Specification
Image Type Color CCD
Horizontal Resolution 4 0 TV lines
Vertical Resolution 390 TV lines
Number of Pixels EIA 70,000
Power Supply 1 VDC
Power Consumption 1.5 watts
Signal-to-Noise Ratio Better than 48 db
Sync System Internal
Scanning System :1 interface
Scanning Frequency 1/60 ~ 1/1 0,000 seconds
Field of View 110°
Impact Rating 10 G
Operating Temperature - °F to +149°F (-30°C to 65°C)
Storage Temperature -4 °F to +185°F (-40°C to 85°C)
Dimensions
(Width x Height x Depth)
3. x .9 x .3 inches
(8 x 73 x 58 mm)
Weight 0.84 pounds (0.38 kg) (including
bracket)
Supplied Accessories  Adjustable mounting bracket
 Extension cable
 Screw kit
Minimum Illumination 0 lux (IR on), 0.1 lux (IR off)
 SV-CBB-56-70 Control Bo
Item Specification
Power Input 1 ~ 4 VDC
Power Consumption 9 ~ 18 watts
Dimensions
Width x Height x Depth
6. x 3.0 x 1.3 inches
157 x 76 x 34 mm
Weight 0.8 pounds (3.5 kg)
Impact Rating 6G
Operating Temperature -4°F to 176°F (- 0°C to 80°C)
Storage Temperature -40°F to 185°F (-40°C to 85°C)
Audio/Video Inputs
Audio/Video Output 1
Supplied Accessories  System power cable
 Screw kit

SV-CLCD56B/70B Quick Installation Guide March 007
SV-CLCD56B_70B QIG Ver.1.0.doc 6
Warranty Information
LIMITED 1-YEAR NEW PRODUCT WARRANTY
Safety Vision, L.P. (“SV”) makes the following limited warranty,
which is effective at the time of the original end-user purchase.
NOTE:
Optional warranty products are available for all SV
products and may be purchased at the time of the original
end-user purchase or any time during the original Limited
1- ear New Product Warranty period.
SV warrants this product against defects in materials for a
period of 1 year after the date of purchase. During this period,
SV will repair or replace a defective product or part without
charge to the customer. The customer must send the defective
product or part to SV or an authorized SV dealer. The customer
must pay for all transportation and insurance charges for
sending the unit to be repaired. SV’s total liability is limited to
the original product cost.
 Quick Installation Guide
The customer should thoroughly read this guide before
operating this product.
 Customer’s Responsibility
The above warranty is subject to the following conditions:
 Customer must notify SV within 10 days of discovering
the defective product or part and provide a description
of the defect and complete information about the
manner of its discovery.
 All warranty servicing of this product must be
performed by SV or an authorized servicing agent.
 Warranty extends only to defects in materials as
limited above. Warranty does not extend to any
product or part that has been lost or discarded by the
customer; to damage to products or parts caused by
misuse, accident, improper installation, improper
maintenance, or use in violation of instructions
furnished with the product; to units that have been
altered or modified without authorization of SV; to
damage to products or parts thereof that have had the
serial number removed, altered, defaced, or rendered
illegible; or to any failure of the product to function
caused by burglary, fire, flood, war, riot, civil
commotion, Acts of God, or any other condition
beyond the control of SV.
 Obtaining Warranty Service
To obtain warranty service, the customer must contact the SV
Service and Warranty Manager at 713.896.6600 or
800.880.8855 to report a defective product. (The customer must
report the model number and serial number if available.) The
Service and Warranty Manager will assist in troubleshooting the
problem and, if necessary, issue a return material authorization
(RMA) number. The customer must include this number on the
outside of each package shipped to SV.
 Important Packing and Shipping Instructions
When a product requires service, only the affected component
must be returned. The customer must use proper packing
material to ensure against damage during shipping. Any
shipping damage caused by improper packing is not covered
under this warranty. In addition, the customer must include a
return material authorization (RMA) number on the outside of
each package shipped to SV and a letter explaining the defect
with the product.
How to Reach Us
If you have exhausted the information in this document and
require further assistance or information, please contact Safety
Vision toll-free at 1-800-880-8855 or send an e-mail message
requesting assistance to: [email protected].
Document Change Log
Version Filename Date
Changes
Made
1.0 SV-CLCD56B_70B QIG VER.1.0.DOC March
007
New
document