Safety Xpress OBSL24 User manual

Page 1 of 8
OVER CAR BONNET
STORAGE LOCKER
INSTALLATION MANUAL
Contents
Product Features & Specifications …………………….Page 2
Parts Drawing……………………………….………...….Page 3
Installation Instructions……………..……………………Page 4-8

Page 2 of 8
Product Feature & Specification
* SKU: OBSL24
* Material: Cold Rolled Steel & Galvanised Sheet
* 2 people recommended for installation
* Adjustable Feet
* 3-point lock for extra security
* Dimensions: 2500(A) x (2000-2300）(B) x 1000(C) x（1000-1300）(D)mm
* Storage Capacity: 2.5 cubic metres
* Before installation measure the height of your vehicle, and take ceiling height into
consideration, to ensure that you can assemble the unit to the correct height
Parts Drawing
05
10
04
06
14
09
13
01
02
03
07
12
02
03
03
07
03
11
08
08
15

Page 3 of 8

Page 4 of 8
Installation Instructions
Step 1
①Read instructions from start to finish for assembly.
②It is recommended that you measure the height of your vehicle and take into consideration
the height of the ceiling before assembling and ensure that it is the right height for your
vehicle as it may be difficult to change the height after it is assembled.
③Assemble parts 01, 11 and 08 together using the M8 nuts provided as shown.
④Connect with M10 bolts and nuts for parts 11, 07, 01, 02.
(04) Door Plate
(08) Front Beam
(02) Adjustable leg
(11) Front right leg
(03) Height adjustable foot
(01) Front left leg
(07) Adjustable Leg B
(03) Height adjustable foot
(08) Front Beam

Page 5 of 8
Step 2
①Assemble back beams and legs using M8 nuts provided (parts 09, 10, 06, 12).
②Connect with M8 bolts and nuts for parts 12, 02, 06, 07.
Note: For most sedan vehicles, the third hole counting from bottom of feet up will be suitable height.
For higher vehicle such as four wheel drives, utes, fourth hole counting from feet up will be suitable
height. Again, please measure and double check vehicle bonnet height and ceiling height before
assembly. Black rubber feet can be twisted and give a little extra height too.
(12) Back right leg
(06) Back left leg
foot
(09) Back top beam
(02) Adjustable leg
A
(03) Height adjustable foot
(10) Back bottom beam
(07) Adjustable leg B
(03) Height adjustable foot

Page 6 of 8
Step 3
Stand the front and back assembled frames up, please have 2 people doing this, and put the 2 x
side panels on as per drawing , using the M8 nuts provide.
(05) Side Panel
(05) Side Panel

Page 7 of 8
Step 4
Install top panels (13), back panels (14) and bottom panels (15) as drawing shows below.
IMPORTANT: Please use the screws provided in the kit to fix each panel, do not use your own
screws.
(13) Top Panel
(15) Bottom Panel
(14) Back panel

Page 8 of 8
Step 5
Installation of Gas Struts
Hold door open and install the gas struts provided as per the diagram below.
Please note: Ensure that gas struts are installed onto the same holes on either side.
E.g. If you are installing the gas struts in the third hole in the door ensure that it is also in the third
hole on the hinge side, otherwise the door will not shut properly resulting in damage to the unit.
IMPORTANT: Please ensure that all parts are assembled correctly according to instructions, check
legs are levelled and unit is stable, before putting anything in the locker or drive your car under the
unit, to prevent any possible issue or damage.
Gas Strut