Sailrite 100102 User manual

103550*1
Binder Installation
Stationary & Swing Binders
#100102, #100103, #100104,
#100105, #102582
Watch video tutorials on installing &
using your Sailrite binder at Sailrite.com

Installing a Stationary Binder
1. Attach the binder to the sewing machine by inserting the two screws (each
with a washer) Dthrough the binder slot Cinto the two holes in the bed of
the machine F. Angle the binder slightly toward the presser foot to better
feed the binding under the foot. Screw placement in the binder slot will vary
from machine to machine.
2. Position the narrow end of the binder Gas close as possible to the foot
assembly without touching the foot or the feed dog using the two screws
next to the feeder mouth A. Typically, the narrow end of the feeder mouth is
right at the front edge of the needle plate slot opening H. The binder should
not come into contact with the foot or feed dog when sewing.
3. If using an Ultrafeed LSZ-1, set the needle position lever in the “Right”
position.
4. J Feed proper-sized binding into the wide end of the feeder mouth and use
a screwdriver blade to pull the binding completely through the slot. Sew off
a small portion of binding to test stitch position.
If presser foot rubs against feeder ledge Bto get the correct stitch position,
remove the feeder ledge with a dremel tool or hack saw.
5. KInsert the raw fabric edge that needs binding into the crease of the
binding as it exits the binder mouth. Feed the material tightly into the crease
of the binding and sew for a perfectly nished edge.
A
B
C
D
Afeeder mouth
Bfeeder ledge
Cbinder slot
Dscrews & washer
F
H
G
J
K
#100104#100105
3/4"
1"

Installing a Swing Binder
1. Attach the binder to the sewing machine by inserting the two screws with
the washer Dthrough the binder slot C (not the 3 holes above the slot) into
the two holes in the bed of the machine F. Screw placement in the binder
slot will vary from machine to machine.
2. Adjust the feeder mouth A from left to right using the large thumb screw
Eand from front to back using the two screws next to the feeder mouth.
Position the binder as close as possible to the foot assembly without
touching the foot or the feed dog G. Typically, the narrow end of the feeder
mouth is right at the front edge of the needle plate slot opening H. The
binder should not come into contact with the foot or the feed dog when
sewing.
3. If using an Ultrafeed LSZ-1, set the needle position lever in the “Right”
position.
4. J Feed proper-sized binding into the wide end of the feeder mouth and use
a screwdriver blade to pull the binding completely through the slot. Sew off
a small portion of binding to test stitch position.
If presser foot rubs against feeder ledge Bto get the correct stitch position,
remove the feeder ledge with a dremel tool or hack saw.
5. K Insert the raw fabric edge that needs binding into the crease of the
binding as it exits the feeder mouth. Feed the material tightly into the crease
of the binding and sew for a perfectly nished edge.
F
H
G
B
E
D
C
Afeeder mouth
Bfeeder ledge
Cbinder slot
Dscrews & washer
Ethumb screw
J
K
#100103 #100102
3/4"
1"
A

Installing a 2" Swing Binder #102582
1. Attach the binder to the sewing machine by inserting the two screws with
the washer Dthrough the binder slot C(not the 3 holes above the slot) into
the two holes in the bed of the machine. Screw placement in the binder slot
will vary from machine to machine.
2. Adjust the feeder mouth Afrom front to back using the two screws next to
the feeder mouth. Position the binder as close as possible to the front of
the presser foot without touching the foot or feed dog F. The binder should
not come into contact with the foot or the feed dog when sewing. Adjust the
stitch position close to the inside edge of the binding by moving the feeder
mouth from left to right using the large thumb screw E.
3. G Feed proper-sized binding into the wide end of the feeder mouth and use
a screwdriver blade to pull the binding completely through the slot. Sew off
a small portion of binding to test stitch position.
4. Insert the raw fabric edge that needs binding into the crease of the binding
as it exits the feeder mouth. Feed the material tightly into the crease of the
binding and sew for a perfectly nished edge.
TIP: For lighter fabrics like Dacron tape, hold your nger in front of the binder to
help keep the fabric from creeping H.
A
B
C
E
D
Afeeder mouth
Bfeeder ledge
Cbinder slot
Dscrews & washer
Ethumb screw
F
G
H