Sainlogic WS0835 User manual

1
SAINLOGIC WS-0835 Professional Wireless
Weather Station User Manual
1. Introduction
Thank you for your purchase of the WS-0835 Professional Wireless
Weather station. The following user guide provides step by step
instructions for installation, operation and troubleshooting.
2. Warnings
Warning: Any metal object may attract a lightning strike, including
your weather station mounting pole. Never install the weather station in
a storm.
Warning: Installing your weather station in an elevated location
may result in injury or death. Safety goes first. Make sure your setup
and preparation is secure, and take no risks.
3. Getting Started
The WS-0835 weather station consists of a display console (receiver),
a sensor array with Integrated Outdoor Transmitter and mounting
hardware
3.1 Parts List
The WS-0835 weather station consists of the following parts (as
referenced in Figure 1 ).
QTY
Item
Image
1
Display Console
Frame Dimensions (LxHxW):
5.3X 1 X 3.7in
LCD Dimensions (LxW):
4.3 x 3in

2
1
Integrated Outdoor
Transmitter
Dimensions (LxHxW)：
13 x 6 x 11in
1
Foot Mounting (with pole
insert)
Dimensions: 3 x 4 x 1 ½”
1
Mounting Bracket Back Plate
(pole mount)
Dimensions:3 x 3 x 1 ”
1
Mounting Pole
Dimensions: 12 x 1½ x 1”
2
Pole mounting nuts (M3) /
bolts Ø3)
4
Pole mounting nuts (M5) /
bolts ( Ø5)

3
Figure 1
3.2 Recommend Tools
Precision screwdriver (for small Phillips screws)
Compass or GPS (for wind direction calibration)
Adjustable Wrench
Hammer and nail for Foot Mounting.
3.3 Sensor Assembly Set Up
The following illustration shows the full segment for Thermo-
Hygrometer ,WIND and RAIN transmitter .purposes only ,as shown in
Figure 2.
4
Tapping screws
1
Manual
1
Power Adapter

4
Figure 2
3.3.1 Insert batteries into the transmitter. Locate the
battery door on the transmitter, push and open the battery compartment,
as show in Figure 3.
Figure 3

5
Remove the battery door on the back of the sensor by removing the set
screw, as shown in Figure 4.
Figure 4
Inserting 3xAA batteries in the battery compartment, as show in Figure
5.
Figure 5

6
Close the battery cover. Make sure the gasket (around the battery
compartment) is properly seated in its place prior to closing the door.
Tighten the set screw.
Note: Do not install the batteries backwards. You can permanently
damage the sensors. The solar panel does not charge the batteries, so
rechargeable batteries are not needed or recommended.
Note: We recommend installing Lithium AA batteries for sensors.
The sensor LED indicator will light for 3 seconds, and then flash once
per 16 seconds thereafter. Each time it flashes, the sensor is
transmitting data.
Place the battery cover and push it to close the compartment.
Note: If the sensor does not power up after inserting the batteries,
press the reset button shown in Figure 6.
Figure 6
3.4 Display Console
3.4.1 Display Console Layout
The display console layout is shown in Figure 7
Note: The following illustration shows the full segment LCD display
for description purposes only and will not appear like this during normal
operation.

7
Figure 7
1.Indoor humidity change
indication
2.Indoor humidity HI/LO alarm icon
3.Indoor temperature change
indication
4.Temperature units (°F or °C)
5.Indoor temperature HI/LO alarm
icon
6.Outdoor humidity HI/LO alarm
icon
7.Battery low voltage prompt
8.Moon phase
9.Reception icon
10.Outdoor temperature mode
11.Daylight Saving Time
12.Time
13.Weather tendency indicator
14.Time Alarm 1
15.Time Alarm 2
16. DATE
17. Wind direction
18. Wind speed units of measure
19.Wind speed Gust display
20.Wind speed average display
21.Wind speed average HI alarm
icon
22. Rainfall display (1h, 24h, week,
month, total)
23.Pressure (REL and ABS) display
24. Rainfall units of measure
25.Pressure units of measure
26. 24hour for clear
27. Indoor humidity display

8
3.4.2 Display Console Set Up
It is recommended to plug in the power supply to reduce the
battery consumption and extend the service life.
Note: The sensor array must be powered and updating before
powering up the console, or the
console will time out searching for the sensors. Power the console last.
Make certain the weather station sensor array is at least 10’ away from
the console and within
100’ of the console. If the weather station is too close or too far away, it
may not receive a proper signal.
Remove the battery door on the back of the display, as shown in Figure
8. Insert three AAA (alkaline or lithium)) batteries in the back of the
display console. The display will beep once and all of the LCD
segments will light up for a few seconds to verify all segments are
operating properly.
Note: The character contrast is best from a slightly elevated viewing
angle.
Figure 8

9
Replace the battery door, and fold out the desk stand and place the
console in the upright position.
The unit will instantly display indoor temperature, humidity, pressure,
tendency, moon phase, and time. The wind speed, wind gust, wind
direction, rain, outdoor temperature and humidity will update on the
display within a few minutes. Do not Press any menu buttons until the
outside transmitter report in, otherwise the outdoor sensor search mode
will be terminated. When the outdoor transmitter data has been
received, the console will automatically switch to the normal mode from
which all further settings can be performed.
While in the search mode, the remote search icon will be constantly
displayed.
Note: The power adapter is intended to be correctly oriented in a
vertical or floor mounted position. The prongs are not designed to hold
the plug in place if it is plugged into a ceiling, under-the-table or cabinet
outlet.
Figure 9
1: Fold out the desk stand and see DC jack on the left ; as shown in
Figure 10

10
Figure 10
2: Insert the DC plug correctly ; as shown in Figure 11
Figure 11
3: If you want to put it on a table or cabinet, opened the desk stand and
turn the DC plug up until 90 degrees; as shown in Figure 12.