SAL PIXIE SMFR/BTAS User manual

SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474
Co yright SAL V16 JUL 2021 | www.sal.net.au | Page 1 of 2
IMPORTANT: IN THE INTEREST OF PRODUCT PERFORMANCE AND SAFETY PLEASE READ THESE INSTALLATION AND WARRANTY INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
SAL roducts are designed in accordance with all mandatory International and Australian Standards, which require installation in
accordance with AS/NZS3000 by a qualified installer and regular cleaning and maintenance of the equi ment. Products are sold
in accordance with the following instructions and SAL standard terms and conditions of sale, available via www.sal.net.au.
Due to continued roduct and information u dates, roduct data sourced from sal.net.au shall not form art of any contract and or technical erformance
guarantee unless ex ressly confirmed in writing by SAL at the time of order.
PIXIE MULTIFUNCTION ROTARY CONTROL electrical and installation s ecification effective 15/11/2021.
Model No. Input (V)/(H ) Min / Max loads(A) Colour Dimension L x W x H (mm) Wireless
SMFR/BTAS 240/50 NA Blue 54 x 24 x 24 Bluetooth Mesh Technology
Nominal frequency (Hz) 50 Product installation orientation Horizontal wall mount
O erating ambient min/max (°C) 0 to 40 Product a lication Interior residential or commercial
O erating humidity 10% to 85% RH, NC Pixie connectivity Yes
Storage ambient limit (°C) 0 to 40
IP rating* 20
Storage humidity 10% to 85% RH, NC Attachment ty e N/A
IP rating for interior roducts: The designated IP rating is “from below the ceiling” unless otherwise s ecified.
IP rating ALL roducts: Termination of the roduct must be made in accordance with the IP rating.
Brief Description:
The PIXIE Multifunction Rotary Control comes with a dial to enhance the interaction in the PIXIE smart home control. It’s a secondary device in PIXIE system, and
can air with a PIXIE master device, a grou , or scenes to achieve intuitive remote control.
Features:
1. An advanced multifunction control device in PIXIE system
2. Need active and neutral wire only
3. Rotary dial for intuitive interactions
4. Fits into most Australian wall lates, max. 6 gang installation
5. Com lementary long neck dial for other wall lates like PIXIE Ambience wall lates
6. Can air and control every PIXIE master device
7. Can air and control u to 2 scenes in PIXIE a
8. Can air and control u to 6 scenes in PIXIE PLUS a
Specific installation procedures (if any):
Installation guide
1. Switch off the mains ower
2. Wire it with active and neutral according to the cable color and wiring diagram. Blue
cable for neutral, red cable for active.
3. Energize the roduct
4. Pair it with a master device, a grou , or scenes
5. Start to use
Operations
LED Indicator
-The color of LED indicator is blue.
-The LED indicator is low light blue when standby
-The LED indicator flashes to highlight blue when the dial is ressed once
-The LED indicator kee s highlight blue when the dial is ressed and hold, or rotated
DIAL operation
General operation
Device operations Function Description LED Indicator Remark
4 clicks
Enter airing mode, to finalise
the airing rocess with a PIXIE
master device, a grou or a
scene
Quickly flash in blue for 10
seconds
Can air with a PIXIE master device, a grou or a scene.
After a successful airing, airing mode will end. Pressing
any button on this roduct during airing mode will cancel
and exit airing mode.
7 Clicks Turn on/off the standby LED
indicator - Can toggle LED indicator on/off at standby mode
9 clicks Reset the roduct to factory
default Flash in blue for 3 seconds All the revious airing will lost after reset

SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474
Co yright SAL V16 JUL 2021 | www.sal.net.au | Page 2 of 2
DIAL operation continued …
Operations when paired with dimmable master products
Paired Device
Operations
PIXIE
Smart Dimmer
PIXIE
Smart RGB Strip, RGB Strip Controller
PIXIE
Smart Single Color Strip, Single Color
Strip Controller
1 Click
Turn ON/OFF.
When turning the light on, it will work
on the last used brightness setting
Turn ON/OFF.
When turning the light on, it will work
on the last used brightness setting.
Turn ON/OFF.
When turning the light on, it will work
on the last used brightness setting.
2 Clicks Shortcut to the maximum brightness Shortcut to the maximum brightness Shortcut to the maximum brightness
3 Clicks
Switch to the next color
tem erature, which circulates in
Warm White->Cool White->Daylight.
For S9842 downlight only.
Switch to the next color. Color
circulates in White->Red->Green->Blue. NA
Long Press
When the light is on, long ress the
button to dim u or down, release
the button to sto .
When the light is off, long ress the
button to turn on the light at
minimum brightness and increase
brightness, release the button to
sto .
When the light is on, long ress the
button to dim u or down, release the
button to sto .
When the light is off, long ress the
button to turn on the light at minimum
brightness and increase brightness,
release the button to sto .
When the light is on, long ress the
button to dim u or down, release the
button to sto .
When the light is off, long ress the
button to turn on the light at minimum
brightness and increase brightness,
release the button to sto .
Rotate
When
the light is on, rotate the dial
clockwise to dim u , anticlockwise
to dim down
When the light is off, rotate the dial
clockwise to turn on the light at
minimum brightness and increase
brightness
When the light is on, rotate the dial
clockwise to dim u , anticlockwise to
dim down
When the light is off, rotate the dial
clockwise to turn on the light at
minimum brightness and increase
brightness
When the light is on, rotate the dial
clockwise to dim u , anticlockwise to
dim down
When the light is off, rotate the dial
clockwise to turn on the light at
minimum brightness and increase
brightness
Operations when paired with scenes
Operations Result Remark
1 Click Activate Scene 1 Available in both PIXIE and PIXIE PLUS A
2 Clicks Activate Scene 2 Available in both PIXIE and PIXIE PLUS A
Rotate clockwise Activate Scene 3 Available with PIXIE PLUS A only, gateway is required
Rotate anticlockwise Activate Scene 4 Available with PIXIE PLUS A only, gateway is required
Press, hold and rotate
clockwise Activate Scene 5 Available with PIXIE PLUS A only, gateway is required
Press, hold and rotate
anticlockwise Activate Scene 6 Available with PIXIE PLUS A only, gateway is required
Operations when paired with a group
Operations Result Remark
1 Click Turn ON/OFF the Grou NA
2 Clicks Shortcut to the maximum brightness Dimmable roduct grou only
3 Clicks Switch colour/colour tem erature Subject to the roduct grou functionality
Long press Grou dimming Dimmable roduct grou only
Rotate clockwise Grou dimming u Dimmable roduct grou only
Rotate anticlockwise Grou dimming down Dimmable roduct grou only

SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474
Co yright SAL V16 JUL 2021 | www.sal.net.au | Page 3 of 2
Pairing Instructions
How to pair with a PIXIE master device – without phone
1. Make sure the PIXIE master device enters airing mode. For most PIXIE master devices, quickly ress the button 4 times will make it into airing mode. For PIXIE smart
stri kits, long ress the “Power button” on the remote will let it enter airing mode.
2. Quickly ress the dial of PIXIE Multifunction Remote Control 4 times within 30 seconds, when the LED indicator flashes twice and kee s solid for 2 seconds, the airing
is successful
How to pair with a PIXIE master device – with phone (Recommended)
3. Make sure the PIXIE master device is added into the A , either PIXIE or PIXIE PLUS
4. Stand close to the PIXIE Multifunction Rotary Control
5. Launch the A , navigate to “Devices”, then find the PIXIE master device that needs to be aired, go to device detail age by ressing its icon
6. Ta to right three dots, then ta “Pairing” in the o -out list
7. Quickly ress the dial of PIXIE Multifunction Remote Control 4 times within 30 seconds, when the LED indicator flashes twice and kee s solid for 2 seconds, the airing
is successful.
How to pair with a group – with phone only
8. Stand close to the PIXIE Multifunction Remote Control
9. Launch the A , navigate to “Grou ”, then select the grou that needs to be aired, go to grou detail age by ressing its icon
10. Ta to right three dots, then ta “Pairing” in the o -out list
11. Quickly ress the dial of PIXIE Multifunction Control 4 times within 30 seconds, when the LED indicator flashes twice and kee s solid for 2 seconds, the airing is
successful
How to pair with a scene – with phone only
12. Stand close to the PIXIE Multifunction Rotary Control
13. Launch the A , navigate to “Scene”, ta to right three dots, then ta “Pairing” in the o -out list, follow the guide in the a and select the referred scenes,
then ress “Confirm and Start Pairing” to start airing
14. Quickly ress the dial of PIXIE Multifunction Rotary Control 4 times within 30 seconds, when the LED indicator flashes twice and kee s solid for 2 seconds, the airing is
successful
Trouble Shooting
Case Issue Suggestions
The LED indicator doesn’t light up -Please check the wiring and make sure the wiring is correct
-Press the button 7 times see if the standby LED indicator was turned off
The LED indicator flashes after quickly pressing
the button 4 times, but it doesn’t pair, and
finally times out
-Please check if the PIXIE Multifunction Rotary Control is within the wireless signal range of the PIXIE
master device
-Make sure there is at least the PIXIE master device is in airing mode rior to ressing the dial of PIXIE
Multifunction Rotary Control 4 times
The LED indicator shows it’s paired successfully,
but it doesn’t control
-Make sure the PIXIE Multifunction Rotary Control is within wireless signal coverage of the aired PIXIE
master devices (within 15 meters in o en s ace, may require closer roximity de ending on installation
environment)
-If it has to be beyond wireless coverage, lease de loy PIXIE signal boosters between PIXIE
Multifunction Rotary Control and PIXIE master devices
 Scan QR code or go to A store (IOS) or Google Play (Android) to download the free PIXIE
a to your smart hone. IOS: Requires IOS
 6.0 or later. Com atible with iPhone, iPad and iPad touch Android: Requires Android 4.4 or
above, devices must su ort Bluetooth 4.0
 S ecifications above are for reference only and may vary without rior notice

SAL National Pty Ltd. 40 Biloela Street Villawood NSW 2163 ABN 21 633 189 474
Co yright SAL V16 JUL 2021 | www.sal.net.au | Page 4 of 2
General product application requirements (if applicable):
1. Recycling – SAL encourages recycling, lease consider the environment when dis osing of ackaging, batteries & com onents.
2. Switching or test intervals – For o timum roduct erformance, good design ractice does not encourage 24/7 o eration of lighting roducts without the rovision
of a routine switching or regulatory test cycle. As a guide for continual o eration installations, a twelve (12) hour duration for Industrial and Commercial a lications
and a six (6) hour duration for Residential a lications should be considered.
3. Product maintenance – In line with the relevant design standards and to rotect your investment, it is im ortant to have in lace a routine cleaning rogram that
reflects the installation environment and maintains the roduct in a clean and functional condition.
IMPORTANT - The su ly must be isolated before any roduct maintenance or cleaning is conducted. In addition, damage to ANY cable or cord su lied with the
roduct must be addressed as follows; For attachment ty e X having a s ecially re ared cable, if the external flexible cable is damaged, it must be re laced by an
equivalent cable exclusively available from the manufacturer or authorised installer. For attachment ty e Y, if the external flexible cable is damaged, it must be
exclusively re laced by an equivalent cable by the manufacturer or authorised installer. For attachment ty e Z, if the external flexible cable is damaged, the cable
cannot be re laced and the luminaire must be destroyed.
4. Adverse, corrosive and coastal installation environments – Unless the roduct is s ecifically designated for such a lications in these installation instructions, which is
su orted by a rofessional maintenance rogram; installation of equi ment in such environments is not recommended.
5. Warranty – In accordance with SAL’s standard terms and conditions of sale, SAL warrant this roduct to be free from defects in materials and or workmanshi for a
eriod as stated below for goods not subject to incorrect installation, maintenance, o eration, mishandling, environmental, unauthorised modifications or electrical
o erating conditions outside the nominated roduct s ecification as detailed in these installation instructions. The benefits to you given by this warranty are in addition
to other rights and remedies you have under law. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to
a re lacement or refund for a major failure and com ensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods re aired
or re laced if the goods fail to be of acce table quality and the failure does not amount to a major failure.
Warranty term – Residential usage (12) months, Commercial usage (12) months, Re laceable lam s (where su lied) (12) months and batteries where su lied (12)
months from date of urchase.
How to make a claim?
Step # 1 – Within 30 days of the fault discovery, lease contact the original lace of the SAL roduct urchase during standard (local) business hours, with the following
information (a) roof of urchase (b) descri tion and quantity of the claimed fault (c) address of installation. (d) o erating hours of the roduct.
Step # 2 – It is then the res onsibility of the original lace of roduct urchase to re ort the matter to SAL aftersales;
NSW | ACT - SAL National Pty Ltd, 40 Biloela Street Villawood NSW 2163 | P # 02 9723 3099
QLD
-
SAL
National
Pty
Ltd,
36
Whitelaw
Place
Richlands
QLD
4077
|
P
#
07
3879
5999
VICT |
TAS
| SA |
NT
-
SAL
National
Pty
Ltd,
46
-
48
Keys
Road
Moorabbin
Victoria
3189
|
P
#
03
9532
3168
WA
-
SAL
National
Pty
Ltd,
29
Beringarra
Av
Malaga
WA
6090
|
P
#
08
9248
7458
Step # 3 - U on review of your claim and if the roduct is required to be returned to SAL for technical evaluation, then at the owners ex ense the roduct must be
returned to SAL as er the above nominated locations.
Step # 4 - Pending the evaluation, the claim will be validated resulting in the roduct being re aired or re laced with the same or best equivalent roduct at the
discretion of SAL, or rejected if the roduct fault was found to be caused by conditions beyond the res onsibility of SAL warranty obligations. Consideration of
installation, roduct removal, return freight and or testing fees are not the res onsibility of SAL.