Salamander Designs EZ Series User manual

Salamander Interactive Wall Mounts 501-518 [04.21] page 1 of 10
user manuAl
ez-lift SERIES interactive
wall mounts
EZ1/ML145
Consists of:
EZ1/MB16/152
EZ1/MA1
Displays up to 39-83 lbs (18-38 kg)
VESA Mounting: 200 x 200 – 800 x 670
Mount Body
VESA Bracket
EZ1/ML209
Consists of:
EZ1/MB16/209
EZ1/MA1
Displays up to 135-197 lbs (61-90 kg)
VESA Mounting: 200 x 200 - 800 x 670
Mount Body
VESA Bracket
EZ1/ML095
Consists of:
EZ1/MB16/095
EZ1/MA5
Displays up to 41.4-85 lbs (18-38 kg)
VESA Mounting: 200 x 100 - 800 x 440
Mount Body
VESA Bracket

Salamander Interactive Wall Mounts 501-518 [04.21] page 2 of 10
PARTS - EZ1/ML145 / EZ1/ML209 / EZ1/ML095
ML095
M4 x 12mm (10x)
M6 x 12mm (10x)
M8 x 10mm (10x)
M8 x 12mm (10x)
2x
2x
B
A
C
M4 x 12mm (10x)
M6 x 12mm (10x)
M8 x 10mm (10x)
M8 x 12mm (10x)
2x
2x
B
A
C

Salamander Interactive Wall Mounts 501-518 [04.21] page 3 of 10
How to use this manual
1 Read manual carefully before you install the mount
2 Carry out the actions fully and in the given sequence
3 The mount guarantee is voided if the product is not correctly installed
 ormodiedinanyway
Warning symbols used
A Sharp edges
B Wear glove
C Physical load
D Twopeoplerequired
E Entanglement hazard
F Warning: Can cause personal
injury or equipment damage
Intended use
The EZ-Lift Mount is a system that compensates the mass of vertically moving displays
to ease vertical movement of the display.
General warning
ThedisplaymayonlybeattachedtoorremovedfromtheEZ-Liftwhenthe
EZ-Lift is in closed position. The EZ-Lift is under strong spring force. Only operate
theEZ-Liftwithanadequatelybalanceddisplayattachedtothedisplayframe.Donot
removeanypartsoftheEZ-Lift.Onlythenishingcovercanberemoved.
Mounting fasteners
Mountingfastenersarenotincludedwiththeproduct.Obtainadvicefromaspecialist.
Setting the springs
Adjust only the outer springs:
• Adjusttheheightoftheouterspringsequally
• Makesurethattheheightofthedisplayisbalanced
• Increasethespringtensionasmuchaspossible
• Makesurethatthedisplaydoesnotmoveup
Never adjust the inner springs
Disposal of the EZ-Lift
Springs should be unattached before disposal of the EZ-Lift. Sort the EZ-Lift,
theaccessoriesandthepackagingfortheenvironmentallyfriendlyrecycling.
A
D E F
B C
Never adjust the inner springs!

Salamander Interactive Wall Mounts 501-518 [04.21] page 4 of 10
Mounting EZ-LIFT Mount Body to Wall
 UnpacktheEZ-Liftandremovetheplasticcoverandtwofoamblocks.
Locating your mount
WOOD CONSTRUCTION:locatetwoframingstuds(minimumof
16”(405mm)apart)atthedesiredlocationusingastudnderdevice.
MASONRY:
aminimumwidthof16”(405mm)isrequiredbetweenfasteners.
Installation of EZ1/MB16/152 Mount Body
Prepare Mounting Site
TheEZ-Liftwasdesignedtobeinstalledona16”oncenter2”x4”woodstud,or
metalstuds,usinghigh-qualityhollowwallanchorinstalledinthecenterofthestud
orasolidconcretewall.
WARNING: INSTALLING THE MOUNT IN UNDERRATED OR DAMAGED CONCRETE
CAN LEAD TO SERIOUS INJURY OR DAMAGE TO PRODUCT! When installing into
concreteonlyinstallthemountinasolidconcretewallmadeof2500PSI(17.3MPa)
orstrongerconcrete.Neverinstallthemountintocracked,chippedorakingconcrete.
WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING
SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers
responsibilitytomakesurethestructuretowhichtheEZ-Liftisbeinginstalledis
capableofsupportingthreetimesthecombinedweightoftheEZ-Liftandall
attachedequipmentisnottoexceedthefollowingweightcapacities:
EZ1/MB16/152:90-152lbs/40-69kg

Salamander Interactive Wall Mounts 501-518 [04.21] page 5 of 10
Determine mounting height
Seebelowforrecommendedmountingheightfor55”Display.Otherdisplayscanbecalculated
byaddinghalftheheightdierencetothetopandhalftheheightdierencetothebottomofthe
exampleshown
79.5”
[2020]
84”
[2134]
16”
[406]
41.25”
[1048] Approx. Lowest Screen Position
Adjustable Range
Mounting
Bracket
Hole Position
Mounting bracket level to wall
 UnpacktheEZ-LiftTakethewallbracketout(A)ofthebox.Notethe
 slotted/slantedholesforlevelwallmounting.
406
16”
300
11.8"
LOCK SCREW HOLE
19
3/4"
31.5”

Salamander Interactive Wall Mounts 501-518 [04.21] page 6 of 10
Make sure screws are unlocked
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Lift the mount onto bracket
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm

Salamander Interactive Wall Mounts 501-518 [04.21] page 7 of 10
Lock mount with screws
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Level vertically with feet at the bottom

Salamander Interactive Wall Mounts 501-518 [04.21] page 8 of 10
Insert plastic cover

Salamander Interactive Wall Mounts 501-518 [04.21] page 9 of 10
Attach brackets to mount and display
OR
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)
Hang display onto horizontal bracket and level
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)

Salamander Interactive Wall Mounts 501-518 [04.21] page 10 of 10
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Set balance
Never adjust the inner springs!
Balancing:Springsarealwaysfullytightenedforsafety.Useadrilldriverand1/2”(13mm)socket,
rotatecounterclockwise(loosen)evenly.Dothreesecondsleftandthreesecondsrightuntilthemount
isevenlybalancedtosupportdisplayweightlessly.
It may be necessary to tighten if balanced
point is exceeded.
SALAMANDER WARRANTY
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS
Salamanderwarrantsagainstmanufacturingdefectsfortwo(2)yearsfromthedateofpurchase.Salamanderwillrepairorreplace,atouroption,any
productdefectiveinmaterialsorcraftsmanship.Batteriesarenotcoveredbythewarranty.
Fullwarrantyincludinglimitationsandwarrantyclaiminformationmaybefoundatwww.salamandercommercial.com
Subject to printing errors and technical amendments.
Lock display with safety lock screws from the bottom
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)