Salamander Designs Strut 170 User manual

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 1 of 8
Use leveler feet to level the unit.
Loosen nut with supplied wrench
and tighten to the locked position.
Mark the wall.
1. Set Strut 170 in Place
A
B
LIMITED WARRANTY 
Salamander is proud to stand behind our products with industry-leading
warranties. Should you ever encounter any problem with your Salamander
product, let us know. We are here to make it right. 1.800.535.5659.
Full warranty including limitations and warranty claim information may be
found at www.salamanderdesigns.com/commercial/warranty
Strut 170 Wall Stand Designed for
Microsoft Surface 2S 50”
ASSEMBLY INSTRUCTIONS (STR170/MS50/FH1)

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 2 of 8
2. Consider Display Position
Display mount panel can be positioned along posts to desired height.
Reference center-line of screen specs below.
.
Lift-o panels can be positioned
above the display mount panel
and then the display mount panel
can be lowered further.
There are a total of 10 dierent
height positions within 16.4”
adjustments and a center display
height ranging from 48” to 64”.
Drop-down access door
30.25in
768.4mm
SCREEN CENTER
SEE TABLE
71.13in
1806.7mm
23.25in
590.6mm
HINGED ACCESS DOOR
4.00in
101.6mm
45°
MAX OPENING
DISPLAY CAPACITY
SIZE 42"-98"
WEIGHT 225 LBS
STANDARD SCREEN CENTER HEIGHT
MIN. 48"
MAX. 64"
DISPLAY MOUNT (VESA COMPLIANT)
HORIZONTAL(MM)
200, 250, 300,
350, 400, 450,
500, 550, 600
VERTICAL(MM)
100, 200, 300,
350, 400
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
A
1 OF 1
SHEET
SCALE
HEAT TREATMENT
CHECKED BY
SURFACE TREATMENT
DATE
ENGINEER
DRAWN BY
MATERIAL
REV DRAWING NUMBER
B
SIZE
TITLE:
811 BLUE HILLS AVE.
BLOOMFIELD, CT 06002
/T/ 860.313.0525 /F/ 860.313.0526
UNLESS OTHERWISE SPECIFIED:
- ALL THREADS TO BE CLASS 2
- COUNTERSINK ALL TAPPED HOLES
- DEBURR HOLES AND BREAK SHARP EDGES
- STAMP, ETCH, OR MARK DRAWING
NUMBER AND REVISION LETTER ON
A NON-CRITICAL SURFACE.
- SURFACE FINISH TO BE 63 RMS
- TOLERANCES:
3rd ANGLE PROJECTION
APPLICATION
NEXT ASSEMBLY
QTY
PROPRIETARY INFORMATION: THIS MATERIAL AND THE CONTENTS THEREOF
ARE CONSIDERED THE PROPERTY OF SALAMANDER DESIGNS, AND THE DISCLOSURE
TO UNAUTHORIZED INDIVIDUALS OR DISSEMINATION, PUBLICATION, OR
COPYING THEREOF IS PROHIBITED WITHOUT PRIOR WRITTEN CONSENT BY
SALAMANDER DESIGNS OF BLOOMFIELD, CONNECTICUT.
CAD
Solidworks
1/64
.015
.005
.0005
.5°
FRACTIONS =
.X=
.XX =
.XXX =
ANGLES =
T.Broderick
STRUT WALL HINGED DOOR
STR170/FH1
3/2/2022
STR170_FH1
1:12
30.25in
768.4mm
SCREEN CENTER
SEE TABLE
71.13in
1806.7mm
23.25in
590.6mm
HINGED ACCESS DOOR
4.00in
101.6mm
45°
MAX OPENING
DISPLAY CAPACITY
SIZE 42"-98"
WEIGHT 225 LBS
STANDARD SCREEN CENTER HEIGHT
MIN. 48"
MAX. 64"
DISPLAY MOUNT (VESA COMPLIANT)
HORIZONTAL(MM)
200, 250, 300,
350, 400, 450,
500, 550, 600
VERTICAL(MM)
100, 200, 300,
350, 400
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
A
1 OF 1
SHEET
SCALE
HEAT TREATMENT
CHECKED BY
SURFACE TREATMENT
DATE
ENGINEER
DRAWN BY
MATERIAL
REV DRAWING NUMBER
B
SIZE
TITLE:
811 BLUE HILLS AVE.
BLOOMFIELD, CT 06002
/T/ 860.313.0525 /F/ 860.313.0526
UNLESS OTHERWISE SPECIFIED:
- ALL THREADS TO BE CLASS 2
- COUNTERSINK ALL TAPPED HOLES
- DEBURR HOLES AND BREAK SHARP EDGES
- STAMP, ETCH, OR MARK DRAWING
NUMBER AND REVISION LETTER ON
A NON-CRITICAL SURFACE.
- SURFACE FINISH TO BE 63 RMS
- TOLERANCES:
3rd ANGLE PROJECTION
APPLICATION
NEXT ASSEMBLY
QTY
PROPRIETARY INFORMATION: THIS MATERIAL AND THE CONTENTS THEREOF
ARE CONSIDERED THE PROPERTY OF SALAMANDER DESIGNS, AND THE DISCLOSURE
TO UNAUTHORIZED INDIVIDUALS OR DISSEMINATION, PUBLICATION, OR
COPYING THEREOF IS PROHIBITED WITHOUT PRIOR WRITTEN CONSENT BY
SALAMANDER DESIGNS OF BLOOMFIELD, CONNECTICUT.
CAD
Solidworks
1/64
.015
.005
.0005
.5°
FRACTIONS =
.X=
.XX =
.XXX =
ANGLES =
T.Broderick
STRUT WALL HINGED DOOR
STR170/FH1
3/2/2022
STR170_FH1
1:12

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 3 of 8
Slide display mount panel along the posts in
incremental height positions of 1.82”.
See Step 3C to place display mount panel
further down the posts.
Position display mount panel to the desired height
by aligning the two top screws to the appropriate
holes in the post and tighten all four screws.
Loosen two bottom screws TWO full rotations and two top panel screws about SEVEN rotations.
Do not completely remove the screws from the flat nuts.
PRO TIP: This process is done easier by
laying the Strut 170 on a horizontal surface
3. Adjust Display Mount Position
A
Top Screw
Bottom Screw
B

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 4 of 8
Slide the display mount panel into the desired height position. Remove lift-panels necessary, see below.
Position display mount panel to the desired height by aligning the two top screws to the appropriate
holes in the post and tighten all four screws.
3. Adjust Display Mount Position
C
Remove the panel lock thumb screws on the lift-o
panels from the backside of unit.
Lift panels up and o, leaving the lift o panel screws.
Removing Lift-O Panels

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 5 of 8
Depending on lift-o panel positions, screws may need to be repositioned.
See diagram to locate appropriate position.
4. Reinstall Lift-O Panels

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 6 of 8
Open the door by pushing door inward
until it clicks, release and it will pop
outward. The door can be pulled open.
1U Vertical Rack Mounting Bracket
Max. Capacity: 19.5”H x 17.75”W x 2.25”D
Mount 1U rack mount component
to the 1U Bracket.
5. Install Rack Mounted Component
A
B
NOTE: Installation of a Tech Shelf or Tech Bracket can be above or below the screen and/or can be used
together. If using 2 peripherals, with one above and below, use a combination of 1 and 2 post mounts
as shown. These can be either 1 post over 2 , or 2 posts over 1.
6. Install Optional Tech Shelf or Tech Bracket
Door
Tech Shelf
Tech Bracket

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 7 of 8
7. Attach to Strut 170 to Wall
Drill 1/2” diameter hole. Hold metal
channel flat alongside plastic straps
and slide channel through hole.
Hold ends of straps between thumb
and forefinger and pull toward you
until channel rests flush behind wall.
Slide plastic cap along straps with either
hand with flange of cap is flush with wall.
Snap straps at wall by pushing side
to side,snapping of straps level with
flange of cap.
Move Strut 170 to wall and attach
bracket. Insert bolt through Bracket
and tighten until snug against wall.
A B
C D
Install wall fasteners
to marked locations
and fasten.
NOTE: Alternate fasteners
provided for wood studs.

Strut 170 Wall Stand Designed for Microsoft Surface 2S 50” 501760MS v1.23 page 8 of 8
Insert the four shoulder washers on the brackets through the keyhole openings
and rest washers at the bottom of the openings.
Attach display mount brackets in locations shown using the 4 M6x14 screws.
8. Attach Brackets to Display
9. Install Display
Attach display mount brackets in locations shown using the 4M6x14 screws
Attach display mount brackets in locations shown using the 4M6x14 screws