Salus RM-16A User manual

www.salus-controls.eu
Relay module
RM-16A
SALUS distributor:
OL Controls Sp. z o.o. Sp. k.
43-262 Kobielice, 4 Rolna St.
tel: [phone],
e-mail: [e-mail], www.salus-controls.eu
The declaration of compliance is on www.salus-controls.pl site
Relay module SALUS Controls
RM-16A
Symbol meaning selecting electric
electronic gear. Putting used gear with
other waste products is strictly forbid-
den. The declaration of compliance is on
www.salus-controls.pl site
Made in Poland
mounting in
a box Ø60
mounting only
inside buldings
Made in Poland
Relay module SALUS Controls
Product code: RM-16A
Relay module RM-16A opens and closes the circuit in order to aect the work of other devices. Some uses
of the module RM-16A with other Salus products are shown below:
1. Connection of the thermostat with the high voltage relay 230V (e.g. VS30/RT200/ERT20/ERT30/ERT50/
VS10) with a gas boiler which requires free-voltage output NO/COM or NC/COM
2. Connection of the SALUS temperature regulator with the NO/COM relay (e.g. 091FL) with the boiler con-
trol which requires NC/COM output (NC/COM output is normally required in the solid fuel boiler controls )
3. Connection of the receiver transmitting power higher than it is allowed by the relay in a regulator. The
maximum electricity consumption of the receiver cannot exeed 16A
4. Connection of the devices other than electro thermal actuators with the wiring centre ( KL06-M/
KL08NSB /KL08RF/KL10/KL10RF) e.g. if you want to connect a pump or an electric heating mat instead
of a electro thermal actuator.

Before connecting the relay module with a dierent device make sure that its parame-
ters are consistent with the RM-16A module specication. Incorrect connection may
cause undesirable action, excessive overheating and combustion hazard. To avert the
hazard make sure that the relay module RM-16A is correctly connected. The connection
of the device can be done only by a qualied installer who has up-to-date eligibility.
SL
N
L
NO
COM
NOCOM
VOLTAGE
FREE
INPUT
NC
μ 16
A / 250 V AC
4000 VA
RM-16A
INPUT
230
V AC
POWER SUPPLY
230
V AC / 50 Hz
SAFETY INFORMATION VISUAL ASPECT
Power: 16A / 250V AC, 4000VA
INPUT NO/COM: Connection of a regulator with the free
voltage relay NO/COM
OUTPUT NC/COM/NO: Output receiver
INPUT SL: Connection of the regulator with the
voltage relay 230V
POWER SUPPLY N/L: Power of 230V AC/50Hz
Measurements: 47x47x21
relay output (NO, COM, NC)
INTRODUCTION
Relay module RM-16A opens and closes the circuit in order to aect the work of other
devices. Some uses of the module RM-16A with other Salus products are shown below:
1. Connection of the thermostat with the voltage relay 230V (e.g. VS30/RT200/ERT20/
ERT30/ERT50/VS10) with a gas-red boiler which requires free-voltage output NO/COM
or NC/COM
2. Connection of the SALUS thermostat with the NO/COM relay (e.g. 091FL) with the
boiler control which needs NC/COM output (NC/COM output is normally required in
the solid fuel boiler controls)
3. Connection of the receiver transmitting power higher than it is allowed by the relay
in a regulator. The maximum electricity consumption of the receiver cannot exeed 16A
4. Connection of the devices other than electro thermal actuators with the wiring
centre ( KL06-M/KL08NSB /KL08RF/KL10/KL10RF) e.g. if you want to connect a pump or
an electric heating mat instead of a electro thermal actuator.
PRODUCT SPECIFICATION
Power supply of the modul RM-16A-230V AC
Control input with the voltage output 230V
Control input with free-voltage output
LED signalling short circuitof the relay output

1. Connection of the thermostat with a voltage relay 230V (e.g. VS30/RT200/ERT20/ERT30/
ERT50/VS10) to a gas boiler which requires free-voltage output NO/COM.
CONNECTION DIAGRAMS
2. Connection of the SALUS temperature regulator with NO/COM relay (e.g. 091FL) with a
boiler control which requires NC/COM output ( NC/COM output is normally required in solid
fuel boilers controls).
CONNECTION DIAGRAMS
A boiler with a free-A boiler with a free-
-voltage relay-voltage relay
ermostat 230Vermostat 230V
ermostat with aermostat with a
free-voltage relayfree-voltage relay
A boiler with NC/A boiler with NC/
COM inputCOM input

CONNECTION DIAGRAMS CONNECTION DIAGRAMS
3. Connection of the receiver transmitting power higher than it is allowed by the relay in a
regulator. The maximuml electricity consumption of the receiver cannot exeed 16A
4. Connection of the devices other than electro thermal actuators with the wiring centre (
KL06-M / KL08NSB / KL08RF / KL10 / KL10RF) e.g. if you want to connect a pump or an electric
heating mat instead of a electro thermal actuator.
A ermostat with aA ermostat with a
free-voltage relayfree-voltage relay
A thermostat with aA thermostat with a
high voltage relayhigh voltage relay
Heating mat max.16AHeating mat max.16A
Wiring centre: KL06-M / KL08NSB / KL08RF / KL10 / KL10RFWiring centre: KL06-M / KL08NSB / KL08RF / KL10 / KL10RF
PowerPower
SupplySupply
и т. д.и т. д.
Pump -> max 16AmpsPump -> max 16Amps
oror
Heating mat -> maxHeating mat -> max
16Amps16Amps
oror
Actuators -> max 16 AmpsActuators -> max 16 Amps
zone 1zone 1 zone 2zone 2 zone 3zone 3 etcetc
max.16Amax.16A