IMPORTER:
QL CONTROLS Sp. z o.o. Sp. k.
ul. Rolna 4, 43-262 Kobielice
PRODUCER:
Salus Limited 6/F,
Building 20E, Phase 3, Hong Kong Science
Park, 20 Science Park East Avenue, Shatin,
New Territories, Hong Kong
Web: www.salus-tech.com
Email: sales
@salus-tech.com
Sales +44 (0) 8700 766900
Technical +44 (0) 8700 766902
Maintaining a policy of continual product development Salus Controls
plc. reserve the right to change specification, design and materials of
products listed in this brochure without prior notice.
Manual Issue No. IM-RT200-001
Electronic Room THERMOSTAT
for Model No. RT200
Instruction Manual
Installation
The RT200 can be either surface mounted or flush switch box mounted.
The standard Industry back plate provides ease of wiring. The back plate has holes to
suit switch boxes and provision for surface wiring.
The RT200 must be located where it would not be subjected to extraneous heat
gain/loss (such as above radiators, direct sunlight or in draughts).
Normal household air circulation.
Wiring
& Back
Plate
Setting
Setpoint
Temperature
Specification
Terminal Name Function
N Neutral
L Live
SL Switched Live
Earth Parking
Adjust knob to
the desired
setpoint
temperature.
Key Function
Knob Setpoint Temperature
Adjustment
Keyboard:
Terminals:
Prior to installing please read the installation guide
Thank you for purchasing this Salus product - if installing for someone else, please ensure
that the instructions are handed to the householder.
Warning - Please read this manual prior to installation or use.
Shock Hazard
This unit must be installed by a competent person, in accordance with BS 7671 (the IEE
Wiring Regulations), or other relevant national regulations and codes of good practise.
Always isolate the AC Mains supply before removing the unit from the Industry
Standard Back Plate.
1) Select a suitable location noting the advice in paragraph 3 of this manual, a suitable
mounting height is 1.5m above FFL
2) Isolate AC mains supply, note this must be 230 Vac and fused at 5 amps.
3) Optimum cable size is 1.5mm CSA; wiring colour codes vary in different countries and
are not defined here.
4) Enter cable to rear of back plate.
5) Securely fix back plate to wall surface or recessed back box using holes provided.
6) Terminate conductors as per the wiring diagram on the unit, ensuring conductors are
firmly gripped beneath square brass washer.
7) This appliance is Double Insulated and must not be earthed except at the Earth
Parking terminal provided.
8) The Industry Standard back plate has 6 holes in which to fix to the surface of your
choice. Please note that some pressure downwards is required to lock the pins in the
Unit to connectors in the Back Plate, retain with the captive screws at the bottom of
the Back Plate taking care not to over tighten.
9) Restore AC mains to system when all associated items are fully installed and test for
correct operation.
This unit does
not require to be
earthed, earth
terminal provided
for safe connection
of all earth wires
only.
Switch Rating : 230V/50Hz/3A
Switch Type : Single pole, single throw (SPST)
Power Supply : 230V/50Hz
Operating Temperature : 0
o
C - 50
o
C
Temperature Setting Range : 5
o
C - 35
o
C
Storage Conditions : -20
o
C - 55
o
C to 90% RH/non condensing
Temperature Control Accuracy : +/- 1
o
C at 25
o
C
Operating Humidity : 0 to 90% RH/non condensing
Agency Approval : CE
Micro Disconnection On Operation : Type 1.B control action
Rated Impulse Voltage : 4kV
