
3
English
3 ĮΧʪϩ˵ʪɇθ˙ϩʪθɵцΧЇϑ˵˝ϩ˵ʪߣࣄťƸƊ²ࣅϑ˝ϑࢋ
4 ťʪθ˙ͱθиθ˝ɵʪϩиʪʪϩ˵ʪʒͱͱθЇϩɇʒϩ˵ʪΧɇʪࡠ
• Ƹ˙ɇϑϩʪϩ˵ʪߤϑʀθʪиϑ˙θͱϩ˵ʪʪʪʀϩθʀɇΧɇθϩࡡɇʒ
then remove the electrical part.
• Connect the connectors on the panel to the connectors
ͱϩ˵ʪʒͱͱθЇϩťA9ࡠ
– Connect the connectors of the swing motor, remote
control sensor, and humidity sensor on the panel to
their respective connectors on the indoor unit PCB.
– đɇʪϑЇθʪϩ˵ɇϩϩ˵ʪʀͱͱЇθϑͱ˙ϩ˵ʪʀͱʪʀϩͱθϑɇϩʀ˵
each other.
• Reassemble the electrical part.
• Close the air filter.
²Їʒϩцϑʪϑͱθ
NOTE
• If any connector is not connected or is connected to a
different colour connector, both the air conditioner and
the remote control will not operate.
5 Check whether the panel is firmly fixed to the indoor
unit.
• đɇʪϑЇθʪϩ˵ɇϩϩ˵ʪϑʀθʪиϑɇθʪ˙ɇϑϩʪʪʒϩ˝˵ϩцЇϩ
there is no gap between the ceiling and the panel, and
that the panel is installed in parallel with the ceiling
ɇʒϩ˵ʪʀʪ˝ͱϩϑࡠ
– If there is a gap between the ceiling and the panel,
adjust the height of the indoor unit.
CAUTION
• If the panel is installed incorrectly onto the cassette,
air may leak out.
đɇʪϑЇθʪϩ˵ɇϩϩ˵ʪθʪϑͱ˝ɇΧ˵ʪθʪࢋ
đɇʪϑЇθʪϩ˵ɇϩϩ˵ʪθʪϑͱ˝ɇΧ˵ʪθʪࢋ
Condensation and drops
Air leaks
Dust
accumulates
Air leaks
from ceiling
ÃʀͱΧʪϩʪϑϩɇɇϩͱ࣍˙ɇϑϩʪ˝࣎ΧθͱʒЇʀʪϑϩ˵ʪΧθͱɵʪϑ
as shown in the figure. Be sure to check again after the
installation.
• When installing the panel, if there are any gaps
between the panel and the indoor unit due
ϩͱʀͱΧʪϩʪϑϩɇɇϩͱ࣍˙ɇϑϩʪ˝࣎ࡡɇθɇʒ
condensation water may leak into the room. Be sure
to remove gaps by using the indoor unit installation
˝ɇЇ˝ʪϑ࣍ͱϩ˵ʪΧɇϩϩʪθϑ˵ʪʪϩ˙ͱθϑϩɇɇϩͱ࣎ࢋ
– For detailed specifications, refer to the installation
manual for the product.