Samsung XPR Series User manual

Outdoor LED Installation Manual
- XPR Series -
Standard Cabinet
LH080XPRZAS/PZ
Rev.0.9

Contents
2
Installation Precautions
1. Product Information
. Specification, Standard Cabinet, Package, Screen Configuration, Fan installation
2. Installation
. Overview, Unboxing, Accessary Assembly, Fan Assembly, Handling Cabinet, Mounting Cabinet,
Y8, Signal B’d Assembly, Cable Connections, Power Connections,
Waterproof/ Bezel Accessary Assembly
3. Accessory Kit
. Tools & Materials
4. Control Room Setting
. System configuration, System Matrix

Installation Precautions –Important Guidelines to Follow
3
•Precautions prior to Installation
- Ensure that all personnel at the site of installation wear personal protection equipment, such as safety helmets, safety
glasses, safety gloves and other appropriate safety equipment.
- Ensure that at least two persons work together to move or transport the product so as to ensure safety.
- Ensure that the power cord is not close to any heat sources. The cord sheath may melt and cause a fire or electric shock.
- Do not install the product in a confined space with poor ventilation. The internal temperature may increase and cause a
fire.
- Make sure you remove the power cord before transporting the product. Transporting the product with the cord connected
may cause a fire or electric shock.
- Make sure you ground the display screens before connecting the power source. Contacting a display that is not
grounded may result in death or severe injuries.

Installation Precautions –Important Guidelines to Follow
4
◇Installation precautions for prevention of damage to LED
Precautions Images
[Be careful to prevent external impact or dropping]
①
After removing the Cover-
Corner from the product prior to installation, exercise caution to
ensure that the LED surface is not exposed to physical impact and the product is not
dropped onto the floor.
②
Do not place the product on a vibrating object. Make sure the LED surface does not face
down onto the floor.
③
Exercise caution to ensure that the corners of the LED module are not damaged due to
contact with external factors.
④
Make sure the number of loaded rows does not exceed two.
①
②
③
④
[Be careful to prevent LED damage due to electric shock]
▶
Do not touch the LED surface with bare hands without wearing anti-static gloves.
[Be careful to prevent LED damage due to chemicals]
▶
Ensure that the product does not contact water, liquids containing alcohol, solvent or
surfactant, or chemicals such as wax, benzene, thinner, mosquitocide, air freshener,
lubricator or cleaning agent.

◇XPR-S Series
. CREE LED
1. Product Information: Specification
5
SPECIFICATIONS XPR-S
Pitch P6 P8 P10 P16TH
Diode CREE CLY6C CREE C4SMM
Max Brightness Nits 8000
Black Uniformity L10 +/- 0.15 (TBD)
Video Processing 24 Bit
Color Capacity 16 Bit
Color Temp 4,500 –9,000K
Refresh Rate (spec 4,800Hz) 7,680Hz 7,680Hz 7,680Hz 7,680Hz
Horizontal Viewing Angle 160
Vertical Viewing Angle
(Top/Bottom) +20 / -65
Contrast Ratio 8,000:1 ↑
Typ. Weight (Kg/sqm) 40 kg ↓
IP Rating (Front/Rear) IP67 / IP66
EMC Class A
Cabinet Material Aluminum
Service Front & Rear

◇XPR-E Series
. NS/XD LED
1. Product Information: Specification
6
SPECIFICATIONS XPR-E
Pitch P6 P8 P10 P16TH P20TH
Diode NS FM2727 XDL-305J
Max Brightness Nits 7000 7500
Black Uniformity L10 +/- 0.15 (TBD)
Video Processing 24 Bit
Color Capacity 16 Bit
Color Temp 4,500 –9,000K
Refresh Rate (spec 4,800Hz) 7,680Hz 7,680Hz 7,680Hz 7,680Hz 7,680Hz
Horizontal Viewing Angle 160
Vertical Viewing Angle
(Top/Bottom) +20 / -65
Contrast Ratio 8,000:1 ↑
Typ. Weight (Kg/sqm) 40 kg ↓
IP Rating (Front/Rear) IP67 / IP65
EMC Class A
Cabinet Material Aluminum
Service Front & Rear

◇Standard Cabinet
- Outside
1. Product Information: Standard Cabinet
7
Front Rear

◇Standard Cabinet
- Product Size
1. Product Information: Standard Cabinet
8
Item Spec
Cabinet Size (W x H) 1000 mm x 1000 mm
Module Size (A x B) 250 mm x 250 mm
Set depth (D) 264.3 mm
Weight [kg] 38 kg

Y8 PDS
SMPS
SMPS
SMPS
SMPS
◇Standard Cabinet (+ Y8)
- Product Inside
1. Product Information: Standard Cabinet
9
①
②
②
②
②
③
④ ⑤
⑥ ⑥
⑦
①
PDS
②
SMPS
③
AC Filter
④
Power In
⑤
Power Out
⑥
External Fan position
⑦
Y8 (1
Y8 for 1 block)

1. Product Information: Package
10
1265
1225
387
◇Outdoor Cabinet Box
- Read the label to make sure it is the right cabinet.
Read the information in the attached label to check
the Model Code and Project No.

1. Product Information: Screen configuration
11
◇Screen configuration (for P8)
The screen is divided by size of the FHD and the size covered by the Y8(T’con) board:
- FHD Zone (15 x 8 Cabinet)
: configuration which is the maximum configuration that can display content with a resolution of FHD or lower
- Y8 Block (3 x 4 Cabinet)
: configuration which is the maximum configuration that can be covered by the Y8 board
FHD ZONE
Y8 Block
Cabinet

1. Product Information: Screen configuration
12
S
F
B
: Signal B’d
: Forward Y8 B’d
: Backward Y8 B’d
◇Note: Zone configuration by screen
Signal B’d
Forward Y8 B’d
Backward Y8 B’d
The location depends on the
cabinet configuration you
want to install.
See LED configurator.
※This zone configuration differs by pitch. Note that the zone configuration diagram below is applicable to P8.
30m
24m
P8 ZONE1 P8 ZONE2
P8 ZONE3 P8 ZONE4
P8 ZONE5 P8 ZONE6

1. Product Information: Screen Configuration
13
◇Note: Zone configuration by screen
The number of cabinets forming the FHD Zone varies depending on the Pitch, and the quantity and location of the
Y8,Signal B'd are also different.
※Zone is the basic control unit of System
※The location of the Redundancy Signal Board is installed in the cabinet where the data ends.
[ XPR060-S/XPR060-E ]
. Cabinet Configuration : 12 x 6
. Resolution : 1920 x 960
. # of Y8 : 12 (24 for redundancy)
. # of Signal : 2
[ XPR080-S/XPR080-E ]
. Cabinet Configuration : 15 x 8
. Resolution : 1800 x 960
. # of Y8 : 10 (20 for redundancy)
. # of Signal : 2
[ XPR100-S/XPR100-E ]
. Cabinet Configuration : 20 x 11
. Resolution : 1920 x 1056
. # of Y8 : 15 (30 for redundancy)
. # of Signal : 2

1. Product Information: Screen Configuration
14
◇Note: Zone configuration by screen
※Zone is the basic control unit of System
※The location of the Redundancy Signal Board is installed in the cabinet where the data ends.
[ XPR160-S/XPR160-E ]
. Cabinet Configuration : 30 x 16
. Resolution : 1800 x 960
. # of Y8 : 12 (24 for redundancy)
. # of Signal : 2
[ XPR200-E ]
. Cabinet Configuration : 40 x 20
. Resolution : 1920 x 960
. # of Y8 : 20 (40 for redundancy)
. # of Signal : 4 (Serial B’d/Box 2 + Serial server only 2)

1. Product Information: Fan installation location
◇Fan installation location
- Fan type : 2 External fan (Intake/Exhaust), 1 Internal fan
- Repeat configuration for 5 Cabinet rows as shown below
Intake fan/ Internal fan
Exhaust fan
Exhaust fan
Intake fan/ Internal fan [External Fan]
[Internal Fan]
5 Columns
Air inlet
Air outlet
Air inlet
Air outlet

2. Installation : Overview
16
Unboxing Cabinets & Accessories
Fan Assembly
Handling Cabinets
Mounting Cabinets
Y8/Signal B’d Assembly
Cable Connection
Power Connection
Control Room Setting
Pre-Working Before Cabinet Hang
Accessories Assembly
SW set up
◇Installation Overview
- The installation follows the below order.
- Prior to the assembly, clearly identify the pre-work.
On-site HW Installation
On-site SW Setup Operation

3. Installation
17
◇Accessories that need to be installed separately before and after the Cabinet assembly are as follows.
EXHAUST FAN
SIGNAL B’d
EXHAUST FAN
EXHAUST FAN
Y8
Y8
(Redundancy)
INTAKE FAN
INTERNAL FA
N
INTAKE FAN
INTERNAL
FAN
INTAKE FAN
INTERNAL
FAN
◇Ex) Total Screen 3x4 Cabinet
1) Pre-Cabinet Installation Accessories
. EXHAUST FAN, INTAKE FAN, INTERNAL FAN
2) Installation Accessories After Cabinet installation
. Y8, Y8(Redundancy), SIGNAL B’d,
COVER ACCESSARY, BEZEL
COVER ACCESSATRY, BEZEL

◇Pre-Installation Work - All Cabinet
Do the following for all cabinets:.
Ex) FHD Zone Screen : 1 cabinet : Work
2. Installation : Unboxing Cabinets & Accessories

Open the box and remove the cushions.
Then, with the handles on the left and right sides of the cabinet,
Lift the cabinet out and peel off the pe bag.
◇Unboxing
①
②②
2. Installation : Unboxing Cabinets & Accessories
* When unboxing the package or moving the product, do not hold the
handles in the middle of the rear door or the plastic covers on both
corners of the top.
Use Handle when
move cabinet
Don’t hold this plastic
part when move cabinet
19
①
①
Squeeze the winged
handles together
and pull them out.

Remove the Cover Corner (x4) on the four corners of the cabinet
◇Unboxing
2. Installation : Accessory Assembly
Attach the Eye Nut (x2) to the brackets at both ends on top of the
cabinet.
Screw point
①
①
①
②③
②
③
②
③
Bolt
Ring
Ring
Eye
Nut
. 1 by 1 installation : Every cabinets
. Section installation : Only Top cabinets of Section block
①
①
①
20