Samsung DV45H6300EG Installation and operation manual

Gas and Electric
Usermanual Dryer
Imagine the possibilities
^j_,/\6 ¢F¢
\ ,_._arnsung.corn,rejb_er
1-._,,31Z.I-SAi\,iSLING/T2L!,-:,:'64;

I Content
Safety instructions
What you need to know about safety instructions ..................................................... 4
Important safety symbols and precautions .............................................................. 4
Important safety instructions ......................................................................... 6
Installing your dryer
Unpacking your dryer ................................................................................ 8
What's included ...................................................................................... 8
Accessories ............................................................................................. 8
Important to installer ................................................................................. 9
Basic requirements ................................................................................... 9
Grounding ........................................................................................... 9
Gas models ............................................................................................. 9
Electric models .......................................................................................... 9
Location considerations ............................................................................. 10
Alcove or closet installations ......................................................................... 10
Ducting requirements ............................................................................... 12
Exhausting ............................................................................................ 13
Dryer exhaust tips ..................................................................................... 14
Gas requirements .................................................................................... 15
Commonwealth of massachusetts installation instructions ............................................ 15
Electrical requirements .............................................................................. 16
Electrical connections ................................................................................. 16
Connecting the inlet hose ........................................................................... 18
Replacement parts and accessories .................................................................. 19
Installation .......................................................................................... 19
Door reversal ........................................................................................ 20
Final installation checklist ............................................................................ 21
,}
Operating instructions, tips ,,
Overview of the control panel ........................................................................ 22
Load the dryer properly ............................................................................... 26
Getting started ........................................................................................ 26
Rack dry .............................................................................................. 28
Child Lock............................................................................................. 29
Drum Light ........................................................................................... 29
English -2

Sound Off............................................................................................. 29
My Cycle .............................................................................................. 30
Smart Care............................................................................................ 30
VentSensor ........................................................................................... 31
Care and cleaning
Control panel ......................................................................................... 32
Tumbler ............................................................................................... 32
Stainless steel tumbler ................................................................................ 32
Dryer exterior ......................................................................................... 32
Dryer exhaust system ................................................................................. 32
Clean the lint filter .................................................................................... 32
?
Special laundry tips .....,,,})
Special laundry tips .................................................................................. 33
Troubleshooting
Check these points if your dryer ...................................................................... 34
Information codes ................................................................................... 35
Appendix
Fabric care chart ..................................................................................... 36
Protecting the environment .......................................................................... 37
Declaration of conformity ............................................................................ 37
Specifications ....................................................................................... 37
Enalish -3

I Safety instructions
Congratulations on your new Samsung Dryer. This manual contains important information on the installation, use,
and care of your appliance. Please take the time to read this manual to take full advantage of your dryer's many
benefits and features.
What you need to know about safety instructions
Please read this manual thoroughly to ensure that you know how to operate the extensive features and functions
of your new appliance safely and efficiently. Retain the manual in a safe place near the appliance for future
reference. Use this appliance only for its intended purpose as described in this instruction manual. The Warnings
and Important Safety Instructions in this manual do not cover all possible conditions and situations that may
occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, or operating
your dryer.
Always contact your manufacturer about problems or conditions you do not understand.
Important safety sgmbols and precautions
WARNING: Hazards or unsafe practices that may result in severe physical injury, death and/or
_ roperty damage.
Follow the information in this manual to minimize the risk of fire or explosion or to prevent property
damage, personal injury, or death.
A CAUTION: Hazards or unsafe practices that may result in physical injury and/or property damage.
NOTE
These warning signs are here to prevent injury to you and others,
Please follow them explicitly.
After reading this section, keep it in a safe place for future reference.
SAVETHESE INSTRUCTIONS
Enalish _4

WARNING =RiSKOF FiRE
= • Clothes dryer installation must be performed by a qualified installer.
, • Install the clothes dryer according to the manufacturer's instructions and local codes.
• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is
installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with
clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint.These
conditions will obstruct clothes dryer airflow and increase the risk of fire.
, . To reduce the risk of severe injury or death, BIIow all installation instructions.
TO REDUCE THE RISK OF FIRE OR EXPLOSION:
Do not dry items that have beer] previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning
solvents, or other flammable or explosive substances.They emit vapors that could ignite or explode. Any
material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed
in the dryer until all traces of these flammable liquids or solids and their fumes have been removed.
There are many highly flammable items used in homes, such as acetone, denatured alcohol, gasoline,
kerosene, some liquid household cleaners, some spot removers, turpentine, waxes, and wax removers.
Do not dry items containing foam rubber (may be labeled latex Barn) or similarly textured rubber-like
materials on a heat setting. Heated foam rubber materials can, under certain circumstances, produce fire by
spontaneous combustion.
,A WHATTO DOIF YOUSMELL GAS:
I_)onot try to light any appliance.
Do not turn on the appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Clear the room, building or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
SAVETHESEINSTRUCTIONS
English _5

Important safety instructions
,d_ WARNING
To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic
precautions, including the following:
1. Read all instructions before using this appliance.
2. Do not use the dryer to dry clothes which have traces of any flammable substance, such asvegetable oil,
cooking oil, machine oil, flammable chemicals, thinner, etc., or anything containing wax or chemicals, such as
mops and cleaning cloths. Flammable substances may cause the fabric to catch fire by itself.
3. Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance.
4. Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when
the appliance is used near children and pets.
5. Before the appliance is removed from service or discarded, remove the door to the drying compartment to
prevent children or animals from becoming trapped inside.
6. Do not reach into the appliance when the drum is moving.
7. Do not install or store this appliance where it will be exposed to the weather.
8. Do not tamper with the internal controls.
9. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended
in the user-maintenance instructions or published in the user-repair instructions that you understand and
have the skills to carry out.
10. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the
fabric softener or product.
11. Clean the lint screen before or after each load.
12. Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
13. Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt.
14. The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel.
15. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a load to catch fire.
16. This appliance must be grounded. See"Electrical requirements"and "Grounding'in the"lnstalling your dryer"
section.
17. This appliance must be properly grounded. Never plug the power cord into a receptacle that is not grounded
adequately and in accordance with local and national codes. Refer to installation instructions for grounding
this appliance.
18. Ensure pockets are free from small irregularly shaped hard objects and foreign material, i.e. coins, knives, pins,
etc.These objects could damage your dryer.
19. Gas leaks may occur in your system, resulting in a dangerous situation.
20. Gas leaks may not be detected by smell alone.
21. Gas suppliers recommend you purchase and install a Ubapproved gas detector.
SAVETHESE INSTRUCTIONS
English _6

_, WARNING
GasAppliances;
WARNING:This product contains chemicals known to the State of California to cause cancer and reproductive
toxicity.
Gasappliances can cause Iowqevel exposure to Proposition 65 listed substances, including but not limited to,
benzene, carbon monoxide, formaldehyde and soot, substances resulting from the incomplete combustion of
natural gas or LPfuels.
iB, CAUTION
1. Do not sit on top of the dryer.
2. Because of continuing product improvements, Samsung reserves the right to change specifications without
notice. For complete details, see the Installation Instructions packed with your product before selecting
cabinetry, making cutouts, or beginning installation.
3. Do not wash clothing with large buckles, buttons, or other heavy metal or solid things.
4. Install and use in accordance with the manufacturer's instructions.
5. All washed and unwashed fabrics that contain vegetable oil or cooking oil can be dangerous. Washing these
items in hot water with extra detergent will reduce, but not eliminate, the hazard. Always use the Cool Down
cycle for these items to reduce their temperature. Never remove these items from the dryer hot or interrupt
the drying cycle until the items have run through the Cool Down cycle. Never pile or stack these items when
they are hot.
6. Take care that children's fingers are not caught in the door when closing it. This may result in injury.
SAVETHESEINSTRUCTIONS

I ZnstaJJingyour dpyer
Unpackingyour dnyep
Unpack your Dryer and inspect it for shipping damage. Make sure you have received all the items shown below, if
your Dryer was damaged during shipping, or you do not have all the items, contact 1-800-SAMSUNG (726-7864).
,_ WARNING
The packing materials can be dangerous to children. Keep all packaging material (plastic bags,
polystyrene, etc.) well out of the reach of children.
To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.
What's included
8} @
1jTo_stvs_ j-S-j _!!!_ ,
Son!!o!_sns! s W'S!s!!n!s! j
Accessories
"Y"-con nector
English-8

Important to installer
Please read the following instructions carefully before installing the dryer.These instructions should be kept for
future reference.
,_. WARNING: Remove the door from all discarded appliances to avoid the danger of a child being trapped
and suffocating.
Basic requirements
Make sure you have everything necessary for the proper installation
A GROUNDED ELECTRICALOUTLET is required.
A POWER CORD electric dryer (except for Canada).
GAS LINES (ifa gas dryer) must meet national and local codes.
The EXHAUST SYSTEM must be made of rigid metal or flexible stiff-walled metal exhaust ducting.
Grounding
This dryer must be grounded. In the event of a malfunction or breakdown, grounding the product will reduce the
risk of electrical shock by providing a path of least resistance for the electrical current.
Gas models
Your dryer has a cord with an equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided with your dryer if it doesn't fit the outlet, have a proper outlet installed by
a qualified electrician.
Never connect the ground wire to the plastic plumbing lines, gas lines, or hot water pipes.
Electricmodels
Your dryer has an optional cord with an equipment-grounding conductor and a grounding plug, which is sold
separately.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Do not modify the plug provided with your dryer if it doesn't fit the outlet, have a proper outlet installed by
a qualified electrician.
If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to
a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the
circuit conductors and connected to the equipment grounding terminal or lead on the dryer.
Enq[ish _9

Location considerations
The dryer should be located where there is enough space at the front for loading the dryer, and enough space
behind for the exhaust system.This dryer is factory-ready for the rear exhaust option.To exhaust out the bottom,
right or the left, use the accessory exhaust kit. Instructions are included with the kit. Make sure the room in which
the dryer is located has enough fresh air.The dryer must be located where there are no air-flow obstructions.
For gas dryers, adequate clearance must be maintained as noted on the data plate to ensure adequate air for
combustion and the proper dryer operation.
The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.The dryer
area must be kept clear of combustible materials, gasoline, and other flammable vapors and liquids. A dryer
produces combustible lint.The area around the dryer should be kept lint-free.
Alcove or closet installations
WARNING
The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or
closet.
No other fuePburning appliance should be installed in the same closet as the dryer.
Minimum clearances between the dryer and adjacent walls or other surfaces:
js_a--es n!_mm! i%ar _ n!!_Omm! i
Top !_!n!_ ra!! iaoie;iront1_!n!.s?ra!! j
L
q )}(( )}
o il. o Vi' E _
Ain. (25 mm)
R 27 in. (686 ram)
C 17 in. (432 mm)
D 2 in. (50 mm)
F 32.4 in. (823 ram)
F 5 in.(127 mm)
Recessedarea Sideview
(closetor confined area)
English _10

Installation with pedesta!
_1
A
C
D
i' '1
E
A 38.7in.(984mm)
B .53.3in. (1S55 mm)
C 27 in. (686 ram)
53 in. (1345 mm) to
Dclear open door
t
J E 32.4in.(823 ram)
F 5 in.(127 mm)
Znsta[lation wRh stacked washing machine and dpgep
_:__::rrrrrrr
i_ A 3 in.(76 mm)
B 48 in.2(3100 m m2)
C 24 in.2(15.50mm 2)
÷
D 3 in. (76 ram)
E 6 in.(152 mm) _
F 773 in. (1968 mm)
G 1 in. (25 ram)
H 27 in. (686 ram)
[I 5 in.@27 mm)
J , 1 in.(25 mm)
K 32.4 in. (823 ram)
L , 8in.(203 mm)
4
The front of the closet must have two unobstructed air openings (B, C) for a combined minimum total2 2
area of 72 in (465 cm )with a minimum clearance of 3 in. (7.6 cm) at the top (A) and bottom (D).
External exhaust elbow requires additional space (L).
Stacking (MODEL NO: SK-SA)
Samsung's Washer and Dryer can be stacked to maximize usable space.
The dryer legs need to be removed to stack the Washer and Dryer. You can purchase an optional stacking
kit from your Samsung retailer.
English _11

Ducdng pequbements
Recommended Use only for short-run installation
i
i Rigid Metallic Flexible _ Rigid Metallic Flexible _
i 0 24.4 m (80 ft.) 12.4 m (41 ft.) 22.6 m (74 ft.) 10.1 m (33 ft.)
i
i t 20.7 m (68 ft.) 11.2 m (37 ft.) 18.9 m (62 ft.) 8.8 m (29 ft.)
i
i 2 17.4 m (57 ft.) 10.1 m (33 ft.) 15.5 m (51 ft.) 7.6 m (25 ft.)
3 14.3 m (47 ft.) '9.0 m (29 ft.) ' 12.5 m (41 ft.) 6..5m (2 ] ft.)
_ non-metallic flexible ducts.
Do not use
Use a 4 inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct.
Do not use a smaller duct.
Ducts larger than 4 inches (10.2 cm) in diameter can result in increased accumulation of lint.
Lint should be removed regularly.
If a flexible metal duct must be used, use the type with a stiff sheet metal wall. Do not use a flexible duct with
a thin foil wall. A serious blockage can result if the flexible metal duct is bent too sharply.
Never install any type of flexible duct in walls, ceilings, or other concealed spaces.
Keep the exhaust duct as straight and short as possible.
Secure joints with duct tape. Do not use screws.
Plastic flexible ducts can kink, sag, be punctured, reduce airflow, extend drying times, and affect the dryer
operation.
Exhaust systems longer than recommended can extend drying times, affect machine operations, and collect
lint.
The exhaust duct should end with an exhaust hood with a swing-out damper to prevent back drafts and
entry of wildlife. Never use an exhaust hood with a magnetic damper.
The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and the
ground or other obstruction.The hood opening should point down.
Never install a screen over the exhaust outlet.
To avoid lint buildup, do not exhaust the dryer directly into a window well. Do not exhaust under a house or
porch.
If the exhaust duct must run through an unheated area, the duct should be insulated and slope slightly down
towards the exhaust hood to reduce condensation and lint buildup.
Inspect and clean the interior of the exhaust system at least once a year. Unplug the power cord before
cleaning.
Check frequently to make sure the exhaust hood damper opens and closes freely.
Check once per month, and clean at least once per year. Note: If your clothes are not getting dry, then check
the duct for obstructions.
Do not exhaust the dryer into a wall, ceiling, crawl space, or concealed space of a building, gas vent, or any
other common duct or chimney.This could create a fire hazard from the lint expelled by the dryer.
English - 12

If the new dryer is installed into an existing exhaust system you must make sure:
The exhaust system meets all local, state, and national codes.
That a flexible plastic duct is not used.
To inspect and clean all lint buildup from inside the existing duct.
The duct is not dented or crushed.
The exhaust hood damper opens and closes freely.
The static pressure in any exhaust system must not exceed 0.83 inches of water column, or be less than 0.
This can be measured with the dryer running with a manometer at the point where the exhaust duct
connects to the dryer. A no-heat setting should be used.The dryer tumbler should be empty and the lint filter
clean.
Exhausting
The dryer shall not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a
building.
Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the
room.
• All dryers must be exhausted to the outside.
Do not assemble the duct with screws or other fastening means that extend into the duct and catch
lint.
The exhaust duct should be 4 inches (102 mm) in diameter.
The total length of flexible metal duct shall not exceed 2.4 m (7.8 ft.).
In the United States:
Use only those foiPtype flexible ducts, if any, specifically identified for use with the appliance by the manufacturer
and that comply with the OutEine for Clothes DryerTransition Ducts, Subject 21S8A.
In Canada:
Use only those foiPtype flexible ducts, if any, specifically identified for use with the appliance by the manufacturer.
Outside the U.S and Canada:
Refer to the local codes.
WARNING
The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or
closet.
NEVERUSEA PLASTICOR NON-METAL FLEXIBLEDUCT.
If your existing ductwork is plastic, non-metal, or combustible, replace it with metal.
Use only a metal exhaust duct that is non-flammable to ensure containment of the exhaust air, heat,
and lint.
English - 13

Dryer exhaust tips
WARNING: A plastic or non-metal flexible duct presents a potential fire hazard.
Make sure your dryer is installed properly so it exhausts air easily.
Use a 4"diameter rigid metal duct.Tape alljoints, including at the dryer.
Never use lint-trapping screws.
Keep ducts asstraight as possible.
Clean all old ducts before installing your new dryer.
Be sure the vent flap opens and closes freely.
inspect and clean the exhaust system annually.
Don't let a poor exhaust sustain slow the drying process bg:
Restricting your dryer with a poor exhaust system. "-...................................................................................................................................................
Using a plastic, thin foil, or non-metal flexible duct.
Unnecessarily using long ducts that have many elbows.
Allowing dented or clogged ducts and vent.
\
English _14

Gas pequipements
THE INSTALLATION MUST CONFORM WITH LOCAL CODES, OR IN THE ABSENCE OF LOCAL CODES, WITH
THE NATIONAL FUEL GAS CODE ANSIIZ223.1, LATEST REVISION (FOR THE UNITED STATES), OR WITH THE
CANICGA-B149 INSTALLATION CODES (FOR CANADA).
Use only natural or LP(liquid propane) gases.
This dryer designed for use with natural gas. If you plan to use your dryer with LP gas (liquid propane), the
conversion must be done by a qualified service technician in order to achieve safe and proper performance.
A 1/2 inch (1.27 cm) gas supply line is recommended and must be reduced to connect to the 3/8 inch (l cm)
gas line on your dryer:The National Fuel Gas Code requires that an accessible, approved manual gas shut-off
valve be installed within 6 inches of your dryer.
Gas dryers installed in residential garages must be raised 18 inches (46 cm) above the floor.
Additionally, a 1/8 inch (0.3 cm) N.RT. (National PipeThread) plugged tapping, accessible for test gauge
connection, must be installed immediately upstream of your dryer's gas supply connection.
Your dryer must be disconnected from the gas supply pipe system during any pressure testing of the system.
DO NOT reuse old flexible metal gas lines. Flexible gas lines must be design certified by the American Gas
Association (CGA in Canada).
• Any pipe joint compound used must be resistant to the action of any liquefied petroleum gas.
As a courtesy, most local gas utilities will inspect a gas appliance installation.
GAS IGNITION -Your dryer uses an automatic ignition system to ignite the burner. There is no constant
burning pilot.
Commonwealth of massachusetts installation instructions
Your dryer must be installed by a licensed plumber or gas fitter. A'T" handle manual gas valve must be installed in
the gas supply line to your dryer. If a flexible gas connector is used to install your dryer, the connector may not be
longer than 3 feet (36 inches).
WARNING
Gas leaks may occur in your system, creating a dangerous situation.
Gas leaks may not be detected by smell alone.
Gas suppliers recommend that you purchase and install a UL-approved gas detector.
Install and use it in accordance with the manufacturer's instructions.
English - 15

Electpical pequipements
The wiring diagram is locatedonthe plate below the control panel.
,_ WARNING
The improper connection of the equipment grounding conductor canresult in ariskofelectric
shock.Checkwith aqualified electrician or servicemanifyou arein doubt asto whether your dryeris
properly grounded.Do not modify the plug providedwith your dryer- if it doesn't fit the outlet, have
aproper outlet installed by aqualified electrician.
To prevent unnecessaryriskoffire,electrical shock,or personalinjury,allwiring andgrounding must
bedone in accordancewith local codes,or in the absenceof localcodes,with the National Electrical
Code,ANSI/NFPANo.70-LatestRevision(forthe U.S.)or the CanadianElectricalCodeCSAC22.1-
LatestRevisionsand localcodesandordinances.It isyour responsibilityto provideadequate electrical
servicesfor yourdryer.
All gasinstallations must bedone in accordancewith the national FuelCode ANSVZ2231- Latest
Revision(forthe U.S.)orCAN/CGA- B149InstallationCodes- LatestRevision(for Canada)and local
codesand ordinances.
ElectPical connections
Beforeoperating or testing, follow allgrounding instructions in the"Grounding"section on page 13.
An individual branch (or separate)circuit serving only your dryerisrecommended. DO NOTUSEAN EXTENSION
CORD.
6as models = U.S.and Canada
A120volt, 60HzA( approved electricalservice,with a 1S-amperefuseor circuit breakeris required.
Electpic models - U.S.0n!y
Most U.S.dryers requirea 120/240volt,60 HzACapproved electrical service.Some require120/208volt,60 Hz
approved electricalservice.Theelectric servicerequirementscan befound onthe datalabel located behind the
door.A30-amperefuse or circuit breakeron both sidesof the lineis required.
Ifapower cord isused,the cord shouldbe plugged into a30-amperereceptacle.
The power cordis NOTprovided with U.S.electric model dryers.
_k WARNING- RISKOFELECTRICSHOCK
When local codesallow,the dectrical supply of the dryermay beconnected by meansof anew power
supplycord kit,marked for usewith adryer,that isU.Llisted andratedat aminimum of120/240volts,
30-amperewith three No.10copper wire conductors terminated with closedloop terminals, open-end
spadelugswith turned up ends,or with tinned leads.
Do not reuseapower supply cordfrom an old dryer.Thepower cord electric supplywiring must be
retained atthe dryercabinet with asuitable Ublisted strainrelief.
Grounding through the neutral conductor is prohibited for (1)new branch-circuit installations,(2)
mobile homes,(3)recreationalvehicles,and (4)areaswhere local codesprohibit grounding through
the neutral conductor.(Usea4-prong plug for 4wire receptacles,NEMAtype 14-gOR.)
EJectpicmodels = Canada0n!y
A 120/240volt, 60Hz ACapproved electrical servicefused through a30-amperefuseor circuit breakeron
both sidesof the lineisrequired.
AllCanadianmodels areshipped with the power cord attached.The power cord should be plugged into a
30-amperereceptacle.
InCanada,you may not converta dryerto 208volts.
English _16

3-WZREsystem connections
1, Loosen or remove the center terminal block screw.
2. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw
of the terminal block.Tighten the screw.
3. Connect the other wires to the outer terminal block screws. Tighten the screws.
4. Tighten the strain reEiefscrews.
5. Insert the tab of the terminaE block cover into your dryer's rear paneEslot.
6. Secure the cover with a holddown screw.
If converting from a4-wire electrical system to a g-wire, the ground strap must be reconnected to the
terminal block support to ground the dryer frame to the neutral conductor.
4-WZREsgstem connections
1,
2.
3.
4,
S.
6.
7.
Remove the center terminal block screw.
Connect the ground wire (green or unwrapped) of the power cord to the external ground conductor screw.
Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with
yellow stripes) under the central screw of the terminal block.
Connect the other wires to the outer terminal block screws. Tighten the screws.
Tighten the strain relief screws.
Insert the tab of the terminal block cover into your dryer's rear panel slot.
Secure the cover with a holddown screw.
J f
i_ Externa ground connector i A ,--- _j_ .............
i B Greenorbarecopperwireofthepowercord l t_ ,h%i,Y %
_' B I
J_ 314 in. (1.9 cm) UL-listed strain relief j i --E
j_i Grounding wire(green/yellow) J ii _ I
J_ Neutral wire (white or center wire)
i
8. With a level, check your dryer and make the necessary adjustments to the leveling legs.
9. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete.
Plug in your dryer, and check its operation by using the checklist below.
10. (GAS MODELS ONLY)
The burner may not ignite initially due to air in the gas line. AHowing your dryer to operate on a heat setting
will purge the line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. Be sure
the gas supply to your dryer has been turned on. In order to confirm the gas ignition, check the exhaust for
heat.
English - 17

Connecting the inlet hose
The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.
1. Turn the cold water faucet off.
2. Attach the brass female end of the Y connector (A) to the cold water
faucet.
3. Attach the straight end of long hose (B) to the Y connector.
4. Using pliers, tighten the coupling with an additional two-thirds turn.
If the Y connector cannot be attached directly to the cold water
faucet, the short hose must be used.
(If space permits, please skip steps 5 to 8, and go directly to step 9.)
5,
6.
7.
8.
9.
Attach the short inlet hose (C} to the cold water faucet.
Screw on the coupling by hand until it is seated on the faucet. ___
Using the pliers, tighten the coupling with an additional two-thirds
turf].
Attach the Y connector CA)to the brass male end of the small hose. "
Screw on the coupling by hand until it is seated on the connector.
Using the pliers, tighten the coupling with an additional two4hirds
turf].
Attach the angled end of long hoses to the fill valve at the bottom of
the dryer rear frame. Screw on the coupling by hand until it is seated
on the fill valve connector.
10. Using pliers, tighten the coupling with an additional two-thirds turn.
/ / /
/
11. Attach the washer hose (D) to the other side of the Y connector CA).
Screw on the hose coupling until it istight. Using pliers, tighten the
coupling with an additional two thirds turn.
12. Check that the water faucets are on.
13. Check for leaks around the Y connector, faucets and hoses.
When you tighten the coupling with pliers, do not overtighten.This may damage the coupling.
£ndish _18

Replacement parts and accessories
If your dryer requires replacement parts or accessories, contact the dealer where you purchased your dryer or the
SAMSUNG customer care center at 1-800-SAMSUNG (726-7864).
Installation
For the proper installation, we recommend that you hire a qualified installer.
1. Move your dryer to an appropriate location for the installation.
Consider installing the dryer and washer side-by-side, to allow access
to the gas, electrical, and exhaust connections. Place two of the carton
cushion-tops on the floor.Tip your dryer on its side so it lies across
both cushion-tops.
2, Set your dryer back in an upright position.
3, To ensure that the dryer provides the optimal drying performance, it
must be level. To minimize vibrations, noise, and unwanted movement,
the floor must be a perfectly level, solid surface.
To set the dryer to the same height asthe washer, fully retract the
leveling feet CA)by turning them counterclockwise, then loosen the
legs by turning them clockwise.
Adjust the leveling feet only as much as necessary to level the
dryer. Extending the leveling feet more than necessary can
cause the dryer to vibrate.
Review the"Exhausting'section on page 13 before installing the exhaust system.
Install the ductwork from your dryer to the exhaust hood.The crimped end of the duct sections must point
away from your dryer.
DQ NOT use sheet metal screws when assembling the ducting.Thesejoints should be taped.
Never use plastic flexible exhaust material.
Tip for tight installations: install a section of the exhaust system onto your dryer before putting it in place.
Use duct tape to secure this section to your dryer, but do not cover the ventilation slots at the back of
the unit in dryer cabinet.
Review the"Electrical requirements" section on page 16.
BEFOREOPERATINGORTESTING, follow the grounding instructions in the"Grounding"section on page 9.
_IL WARNING- U.S. MODELS
RISK OF ELECTRIC SHOCK - All U.S.models are produced for a S-WIRE SYSTEM CONNECTION.
The dryer frame is grounded to the neutral conductor at the terminal block.
A4-WIRE SYSTEM CONNECTION is required for new or remodeled construction, mobile homes, or if
local codes do not permit grounding through the neutral conductor, if the 4-wire system is used, the
dryer frame cannot be grounded to the neutral conductor at the terminal block.
Refer to the following instructions lot"Electrical connections" on page 16.
Remove the terminal block cover plate.
Insert the power cord with a Ublisted strain relief through the hole provided in the cabinet near the terminal
block.
A strain must
relief be used.
Do not loosen the nuts already installed on the terminal block. Be sure they are tight.
Use a 3/8 in. (1 cm) deep well socket.
English- 19

Review the"Gas requirements" section on page 1S.
Remove the pipe thread protective cap. Apply a pipejoint compound or about 1V2wraps of Teflon tape over
all threaded connections.
The pipe joint compound must be resistant to the actions of any liquefied petroleum gas.
Connect the gas supply to your dryer. An additional fitting is required to connect the 3/4" (1.9 cm) female
thread end of a flexible connector to the 3/8" (1 cm) male threaded end on the dryer.
Securely tighten the gas line fitting over the threads.
Turn on the gas supply.
Check all gas connections for leaks using a soap solution.
If bubbles appear, tighten the connections and recheck. DO NOT use an open flame to check for gas leaks.
Doop peversaJ
1. Unplug the power cord.
2. Remove two door hinge screws.
3. Lift the door and remove it.
4. Remove two screws from the frame front.
5. Remove the two screws from the opposite side of the door hinge.
6. Remove the two screws from the holder lever.
7. Reassemble the two screws on the inside holes.
English _20