Samsung DVD P241 - Progressive-Scan DVD Player User manual

DVD PLAYER
Chassis : Trino
DVD-P241
SERVICE
1. Precautions
2. Alignment and Adjustment
3. Exploded Views and Parts List
4. Electrical Parts List
5. Block Diagram
6. Schematic Diagrams
Manual
DVD PLAYER CONTENTS
SERVICE MANUAL DVD-P241
STANDBY/ON EZVIEW LOADING
ELECTRONICS
© Samsung Electronics Co., Ltd. DEC. 2003
Printed in Korea
AK82-00418A
If you want to know additional information which is not included on this Service Manual, please refer to the
DVD-P241 Training Manual (AK82-00419A).
This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
international and/or domestic law.

Samsung Electronics 1-1
1. Precautions
1-1 Safety Precautions
1) Before returning an instrument to the customer,
always make a safety check of the entire instrument,
including, but not limited to, the following items:
(1) Be sure that no built-in protective devices are
defective or have been defeated during servicing.
(1)Protective shields are provided to protect both
the technician and the customer. Correctly replace
all missing protective shields, including any
removed for servicing convenience.
(2)When reinstalling the chassis and/or other as-
sembly in the cabinet, be sure to put back in place
all protective devices, including, but not limited to,
nonmetallic control knobs, insulating fish papers,
adjustment and compartment covers/shields, and
isolation resistor/capacitor networks. Do not oper-
ate this instrument or permit it to be operated with-
out all protective devices correctly installed and
functioning.
(2) Be sure that there are no cabinet openings through
which adults or children might be able to insert
their fingers and contact a hazardous voltage. Such
openings include, but are not limited to, excessive-
ly wide cabinet ventilation slots, and an improper-
ly fitted and/or incorrectly secured cabinet back
cover.
(3) Leakage Current Hot Check-With the instrument
completely reassembled, plug the AC line cord
directly into a 120V AC outlet. (Do not use an iso-
lation transformer during this test.) Use a leakage
current tester or a metering system that complies
with American National Standards institute (ANSI)
C101.1 Leakage Current for Appliances and
Underwriters Laboratories (UL) 1270 (40.7). With
the instrument’s AC switch first in the ON position
and then in the OFF position, measure from a
known earth ground (metal water pipe, conduit,
etc.) to all exposed metal parts of the instrument
(antennas, handle brackets, metal cabinets, screw-
heads, metallic overlays, control shafts, etc.), espe-
cially any exposed metal parts that offer an electri-
cal return path to the chassis.
Any current measured must not exceed 0.5mA.
Reverse the instrument power cord plug in the out-
let and repeat the test. See Fig. 1-1.
Any measurements not within the limits specified
herein indicate a potential shock hazard that must
be eliminated before returning the instrument to
the customer.
Fig. 1-1 AC Leakage Test
(4) Insulation Resistance Test Cold Check-(1) Unplug
the power supply cord and connect a jumper wire
between the two prongs of the plug. (2) Turn on the
power switch of the instrument. (3) Measure the
resistance with an ohmmeter between the
jumpered AC plug and all exposed metallic cabinet
parts on the instrument, such as screwheads,
antenna, control shafts, handle brackets, etc. When
an exposed metallic part has a return path to the
chassis, the reading should be between 1 and 5.2
megohm. When there is no return path to the chas-
sis, the reading must be infinite. If the reading is
not within the limits specified, there is the possibil-
ity of a shock hazard, and the instrument must be
repaired and rechecked before it is returned to the
customer. See Fig. 1-2.
Fig. 1-2 Insulation Resistance Test
DEVICE
UNDER
TEST
(READING SHOULD
NOT BE ABOVE
0.5mA)
LEAKAGE
CURRENT
TESTER
EARTH
GROUND
TEST ALL
EXPOSED METER
SURFACES
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
2-WIRE CORD
Antenna
Terminal
Exposed
Metal Part
ohm ohmmeter

Precautions
1-2 Samsung Electronics
2) Read and comply with all caution and safety re-
lated notes on or inside the cabinet, or on the chas-
sis.
3) Design Alteration Warning-Do not alter or add to
the mechanical or electrical design of this instru-
ment. Design alterations and additions, including
but not limited to, circuit modifications and the
addition of items such as auxiliary audio output
connections, might alter the safety characteristics of
this instrument and create a hazard to the user. Any
design alterations or additions will make you, the
servicer, responsible for personal injury or property
damage resulting therefrom.
4) Observe original lead dress. Take extra care to
assure correct lead dress in the following areas:
(1) near sharp edges, (2) near thermally hot parts (be
sure that leads and components do not touch ther-
mally hot parts), (3) the AC supply, (4) high voltage,
and (5) antenna wiring. Always inspect in all areas
for pinched, out-of-place, or frayed wiring, Do not
change spacing between a component and the
printed-circuit board. Check the AC power cord for
damage.
5) Components, parts, and/or wiring that appear to
have overheated or that are otherwise damaged
should be replaced with components, parts and/ or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
6) Product Safety Notice-Some electrical and mechani-
cal parts have special safety-related characteristics
which are often not evident from visual inspection,
nor can the protection they give necessarily be
obtained by replacing them with components rated
for higher voltage, wattage, etc. Parts that have spe-
cial safety characteristics are identified by shading,
an ( )or a ( )on schematics and parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire and/or
other hazards. Product safety is under review con-
tinuously and new instructions are issued whenev-
er appropriate.

Precautions
Samsung Electronics 1-3
1-2 Servicing Precautions
CAUTION : Before servicing units covered by this
service manual and its supplements, read and follow
the Safety Precautions section of this manual.
Note : If unforseen circumstances create conflict
between the following servicing precautions and any
of the safety precautions, always follow the safety pre-
cautions. Remember: Safety First.
1-2-1 General Servicing Precautions
(1) a. Always unplug the instrument’s AC power cord
from the AC power source before (1) re-moving
or reinstalling any component, circuit board,
module or any other instrument assembly, (2)
disconnecting any instrument electrical plug or
other electrical connection, (3) connecting a test
substitute in parallel with an electrolytic capaci-
tor in the instrument.
b. Do not defeat any plug/socket B+ voltage inter-
locks with which instruments covered by this
service manual might be equipped.
c. Do not apply AC power to this instrument and
/or any of its electrical assemblies unless all
solid-state device heat sinks are correctly in-
stalled.
d. Always connect a test instrument’s ground lead
to the instrument chassis ground before connect-
ing the test instrument positive lead. Always
remove the test instrument ground lead last.
Note : Refer to the Safety Precautions section ground
lead last.
(2) The service precautions are indicated or printed on
the cabinet, chassis or components. When servic-
ing, follow the printed or indicated service precau-
tions and service materials.
(3) The components used in the unit have a specified
flame resistance and dielectric strength.
When replacing components, use components
which have the same ratings. Components identi-
fied by shading, by( ) or by ( ) in the circuit dia-
gram are important for safety or for the characteris-
tics of the unit. Always replace them with the exact
replacement components.
(4) An insulation tube or tape is sometimes used and
some components are raised above the printed
wiring board for safety. The internal wiring is
sometimes clamped to prevent contact with heat-
ing components. Install such elements as they
were.
(5) After servicing, always check that the removed
screws, components, and wiring have been in-
stalled correctly and that the portion around the
serviced part has not been damaged and so on.
Further, check the insulation between the blades of
the attachment plug and accessible conductive
parts.
1-2-2 Insulation Checking Procedure
Disconnect the attachment plug from the AC outlet
and turn the power ON. Connect the insulation resi-
stance meter (500V) to the blades of the attachment
plug. The insulation resistance between each blade of
the attachment plug and accessible conductive
parts(see note) should be more than 1 Megohm.
Note : Accessible conductive parts include metal pan-
els, input terminals, earphone jacks, etc.

Precautions
1-4 Samsung Electronics
1-3 ESD Precautions
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be dam-
aged easily by static electricity.
Such components commonly are called Electrostati-
cally Sensitive Devices(ESD). Examples of typical ESD
devices are integrated circuits and some field-effect
transistors and semiconductor chip components. The
following techniques should be used to help reduce
the incidence of component damage caused by static
electricity.
(1) Immediately before handling any semiconductor
component or semiconductor-equipped assembly,
drain off any electrostatic charge on your body by
touching a known earth ground. Alternatively,
obtain and wear a commercially available dis-
charging wrist strap device, which should be
removed for potential shock reasons prior to apply-
ing power to the unit under test.
(2) After removing an electrical assembly equipped
with ESD devices, place the assembly on a conduc-
tive surface such as aluminum foil, to prevent elec-
trostatic charge buildup or exposure of the assem-
bly.
(3) Use only a grounded-tip soldering iron to solder or
unsolder ESD devices.
(4) Use only an anti-static solder removal devices.
Some solder removal devices not classified as
“anti-static” can generate electrical charges suffi-
cient to damage ESD devices.
(5) Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESD devices.
(6) Do not remove a replacement ESD device from its
protective package until immediately before your
are ready to install it.(Most replacement ESD
devices are packaged with leads electrically short-
ed together by conductive foam, aluminum foil or
comparable conductive materials).
(7) Immediately before removing the protective ma-
terials from the leads of a replacement ESD device,
touch the protective material to the chassis or cir-
cuit assembly into which the device will be
installed.
CAUTION : Be sure no power is applied to the ch-
assis or circuit, and observe all other safety precau-
tions.
(8) Minimize bodily motions when handling unpack-
aged replacement ESD devices. (Otherwise harm-
less motion such as the brushing together of your
clothes fabric or the lifting of your foot from a car-
peted floor can generate static electricity sufficient
to damage an ESD device).

Precautions
Samsung Electronics 1-5
1-4 Handling the optical pick-up
The laser diode in the optical pick up may suffer elec-
trostatic breakdown because of potential static elec-
tricity from clothing and your body.
The following method is recommended.
(1) Place a conductive sheet on the work bench (The
black sheet used for wrapping repair parts.)
(2) Place the set on the conductive sheet so that the
chassis is grounded to the sheet.
(3) Place your hands on the conductive sheet(This
gives them the same ground as the sheet.)
(4) Remove the optical pick up block
(5) Perform work on top of the conductive sheet. Be
careful not to let your clothes or any other static
sources to touch the unit.
◆Be sure to put on a wrist strap grounded to the
sheet.
◆Be sure to lay a conductive sheet made of copper
etc. Which is grounded to the table.
Fig.1-3
(6) Short the short terminal on the PCB, which is in-
side the Pick-Up ASS’Y, before replacing the Pick-
Up. (The short terminal is shorted when the Pick-
Up Ass’y is being lifted or moved.)
(7) After replacing the Pick-up, open the short termi-
nal on the PCB.
THE UNIT
WRIST-STRAP
FOR GROUNDING
1M
1M CONDUCTIVE SHEET

Precautions
1-6 Samsung Electronics
1-5 Pick-up disassembly and reassembly
1-5-1 Disassembly
1) Remove the power cord.
2) Disassemble the Deck-Assy.
3) Make solder land 2 points short on Pick-up.
(See Fig. 1-4)
4) Disassemble the Pick-up.
1-5-2 Assembly
1) Replace the Pick-up.
2) Remove the soldering 2 points on Pick-up.
3) Reassemble the Deck-Assy.
PICK-UP ASS'Y
SOLDER LAND 2 POINTS SHORT
Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged.
Fig. 1-4

Samsung Electronics 2-1
2. Alignment and Adjustment
2-1 Location of Test Point
Fig. 2-1 Location of Test Point
Pin 29 of RIC1

Alignment and Adjustment
2-2 Samsung Electronics
2-2-1 Adjustment Spec. and Test Point
2-2 Skew Adjustment
Test Disc Adjustment Spec. Test Point Adjustment Location
TDV-533 “Pin 29 of RIC1” Screw A / B
Chapter 14 Flat Waveform (Main PCB - Component Side) Ass’y Deck - Top Side
(See Fig. 2-1) (See Fig. 2-2)
Fig. 2-2 Ass’y Deck (Top Side)
◆Test Disc ; Service not Available
<Table 2-1>

Alignment and Adjustment
Samsung Electronics 2-3
2-2-2 SKEW Adjustment Method
Needed to minimize the variations in Skew of the Pickup unit and to provide optimum match with the recorded
signal on the Disc.
1) Connect an Oscilloscope to the “Pin 29 of RIC1” Test Point (See Fig. 2-1).
2) Connect Power, Open the Tray and Play the TDV-533 Disc, Chapter 14.
◆Set the Oscilloscope Range as follows :
(Voltage ; 20mV/Div., Frequency ; 10m Sec.)
3) Adjust the Screws “A” and “B” (See Fig. 2-2) using a Hex screwdriver until you obtain a Flat Waveform and
the picture is stable.
Then, go to Chapter 1 and make sure the Waveform is Flat here as well.
If not, you have to go back to Chapter 14 and adjust again.
If you cannot obtain a Flat waveform, then the unit is defective.
Note : The Deck must be in a horizontal position. Use both “A” and “B” screws to adjust.
   
    
Typical Waveform before Adjustment Waveform after Correct Adjustment
Fig. 2-3 Envelope Waveform

Samsung Electronics 3-1
3. Exploded View and Parts List
3-1 Cabinet Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-2 Deck Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Page
3-2
3-4

Exploded Views and Parts List
3-2 Samsung Electronics
3-1 Cabinet Assembly
P025
C015
W001
P001
C001
A001
C002
W005
W005

Exploded Views and Parts List
3-3
Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
A001 AK59-00011K REMOCON-ASSY;DVD-P240/XAA,XAA,-,-,36,-,-
C001 AK97-00660B ASSY CABINET-FRONT;HIPS 94 V2,DVD-P240/X
C002 AK64-00503B DOOR-TRAY;DVD-P240/XAA,TSEC,ABS 94HB,T2.
C015 AK64-00500C CABINET-TOP;DVD-P142/XEL,SECC,T0.5,W429.
P001 AK92-00339A ASSY PCB-MAIN;DVD-P241,MAIN ASSY
P025 AC39-10200N CBF POWER CORD;EP2,SPT-2,AWG#18,1.8MT,WA
W001 6003-000275 SCREW-TAPTITE;BH,+,B,M3,L10,BLK ,SWCH101
W005 6003-000117 SCREW-TAPTITE;BH,+,B,M3,L6,ZPC(YEL),SWRC

Exploded Views and Parts List
3-4 Samsung Electronics
3-2 Deck Assembly
H212
H205
H210
H209
H903
H104
H109
H106
H105
H107
H207
H206
H904 H904
H211
H206
H203
H103
H108
H204
H903
H903
H241
H102
H202
H900

Exploded Views and Parts List
3-5
Samsung Electronics
Loc. No Parts No. Description ; Specification Remark
H102 AH66-00111B CLAMPER-ASSY;DP-5,POM,-,-,-,-,BLK,-
H103 AK66-00042A GEAR-PULLEY;DP-15,POM,-,-,-,WHT,-,-,-
H104 AK97-00608A ASSY-MOTOR LOAD;-,DP-15,-
H105 6602-001076 BELT-RECTANGULAR;CR,T1.2,4.3%,1.2X25.1,B
H106 AK66-00041A GEAR-TRAY;DP-15,POM,-,-,-,WHT,-,-,-
H107 AK66-00045A SLIDER HOUSING;DP-15,POM,-,W17.8,L90,WHT
H108 AK63-00101A TRAY-DISC;DP-15,ABS,-,W120,L186.3,-,BLK,
H109 AK92-00328A ASSY PCB-DECK;DP-15,-
H202 AK73-00005B RUBBER-INSULATOR;DP-15,BUTYL,•’12,HS30,H
H203 AH61-50327A SHAFT-P/U;DP-3,SUS,L84.7,OD3,-,-,-
H204 AK66-00043A GEAR-FEED A;DP-15,POM,-,-,-,-,-,-,-
H205 AK66-00044A GEAR-FEED B;DP-15,POM,-,-,-,-,-,-,-
H206 AK61-00032A HOLDER-CAM SKEW;DP-9,POM,-,-,-,BLACK,-
H207 AK31-00014A MOTOR SPINDLE;DP-15,3000RPM,-,-,-,-
H209 AK64-00491A CHASSIS SUB;DP-15,POM,-,-,-,-,-
H210 AK31-00005A MOTOR-FEED ASSY;-,DP-9,-,-,-,-,-,-,-,-,-
H211 AK97-00638A ASSY-PICK UP;-,SOH-DT2,TRINO ASSY PICK U
H212 AK61-00253A HOLDER-CHUCK;DP-15,POM,-,-,-,-,-
H241 AK41-00156A FFC-P U;DP-15,-,FFC,24,T0.3,LEFT
H900 6003-001157 SCREW-TAPTITE;PWH,+,B,M2,L6,ZPC(YEL),SWR
H903 6001-001370 SCREW-MACHINE;CH,+,M1.7,L3.0,ZPC(YEL),SW
H904 6002-001086 SCREW-TAPPING;PH,+,B,M1.7,L5.0,ZPC(YEL),

This Document can not be used without Samsung’s authorization.
Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark
Samsung Electronics 4-1
P001 AK92-00339A ASSY PCB-MAIN;DVD-P241,MAIN ASSY
AC100 2203-000426 C-CER,CHIP;0.018NF,5%,50V,C0G,TP,1608
AC18 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
AC19 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
AC20 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
AC21 2203-000315 C-CER,CHIP;0.12NF,5%,50V,C0G,TP,1608
AC22 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
AC23 2203-000125 C-CER,CHIP;1.2nF,10%,50V,X7R,TP,1608,-
AC24 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
AC25 2203-000315 C-CER,CHIP;0.12NF,5%,50V,C0G,TP,1608
AC26 2203-000125 C-CER,CHIP;1.2nF,10%,50V,X7R,TP,1608,-
AC27 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
AD1 0407-000114 DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOT-
AD2 0407-000114 DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOT-
AD3 0407-000114 DIODE-ARRAY;DAN202K,80V,100mA,CA2-3,SOT-
AD4 0401-000008 DIODE-SWITCHING;DAN217,80V,100mA,SOT-23,
AE10 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
AE11 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
AE12 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
AE13 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
AE14 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
AE15 2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5
AE16 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
AE3 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
AE5 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
AE8 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
AE9 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
AIC2 1002-001294 IC-D/A CONVERTER;PCM1742KE,24BIT,TSSOP,1
AIC4 1201-000163 IC-OP AMP;4560,SOP,8P,173MIL,DUAL,100V/m
AL1 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
AL2 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
AQ1 0504-000128 TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP
AQ2 0504-000156 TR-DIGITAL;KSR2103,PNP,200MW,22K/22K,SOT
AQ3 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
AQ4 0504-000128 TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP
AQ5 0504-000156 TR-DIGITAL;KSR2103,PNP,200MW,22K/22K,SOT
AQ6 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
AQ7 0504-000128 TR-DIGITAL;-,NPN,200MW,22K/22K,SOT-23,TP
AQ8 0504-000156 TR-DIGITAL;KSR2103,PNP,200MW,22K/22K,SOT
AQ9 0501-000314 TR-SMALL SIGNAL;KSA812,PNP,150mW,SOT-23,
AR100 2007-000113 R-CHIP;33ohm,5%,1/10W,TP,1608
AR14 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
AR15 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608
AR16 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608
AR17 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
AR28 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
AR29 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608
AR30 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608
AR31 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
AR41 2007-001179 R-CHIP;8.2Kohm,5%,1/10W,TP,1608
AR42 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
AR43 2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608
AR44 2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608
AR45 2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608
AR46 2007-001179 R-CHIP;8.2Kohm,5%,1/10W,TP,1608
AR47 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
AR48 2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608
AR49 2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608
AR50 2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608
AR52 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
AR54 2007-000102 R-CHIP;100Kohm,5%,1/10W,TP,1608
AR55 2007-000077 R-CHIP;470ohm,5%,1/10W,TP,1608
DCN1 3708-001696 CONNECTOR-FPC/FFC/PIC;24P,1MM,STRAIGHT,S
DCN2 3708-001266 CONNECTOR-FPC/FFC/PIC;11P,1MM,STRAIGHT,S
DOC1 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608
DOC2 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
DOC3 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
DOC4 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
DOE1 2401-000598 C-AL;1uF,20%,50V,GP,TP,4x7,5
DOIC1 AH14-10004R IC;M74HCU04,SOP,TAPE 14P
DOL1 2901-001125 FILTER-EMI ON BOARD;50V,0.5A,-,220pF,7x2
DOL2 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
DOL3 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
DOR1 2007-000076 R-CHIP;330ohm,5%,1/10W,TP,1608
DOR2 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
DOR3 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608
DQ1 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
DQ2 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
DQ3 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
DR1 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
DR2 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
DR3 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
DR4 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
DR5 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
DR6 2007-000075 R-CHIP;220ohm,5%,1/10W,TP,1608
FC1 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608
FC10 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
FC11 2203-001607 C-CER,CHIP;0.22nF,5%,50V,NP0,TP,1608
FC12 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
FC2 2203-001607 C-CER,CHIP;0.22nF,5%,50V,NP0,TP,1608
FC3 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608
FC4 2203-000669 C-CER,CHIP;27nF,10%,25V,X7R,TP,1608,-
FC5 2203-000140 C-CER,CHIP;1.5nF,10%,50V,X7R,TP,1608,-
FC6 2203-000669 C-CER,CHIP;27nF,10%,25V,X7R,TP,1608,-
FC8 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
FC9 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608
FE1 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
FE2 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
FE3 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
FIC1 1003-001661 IC-MOTOR DRIVER;FAN8004,HQFP,48P,13.2x13
FR1 2007-000100 R-CHIP;68Kohm,5%,1/10W,TP,1608
FR10 2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608
FR11 2007-000093 R-CHIP;20Kohm,5%,1/10W,TP,1608
FR12 2007-000329 R-CHIP;11Kohm,5%,1/10W,TP,1608
FR13 2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608
FR14 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
FR15 2007-000655 R-CHIP;27Kohm,5%,1/10W,TP,1608
FR16 2007-007277 R-CHIP;392ohm,1%,1/10W,TP,1608
FR17 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
FR18 2007-000127 R-CHIP;9.1Kohm,5%,1/10W,TP,1608
FR19 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
FR2 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
FR20 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
FR21 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
FR22 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
FR23 2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608
FR24 2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608
FR25 2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608
FR26 2007-000094 R-CHIP;22Kohm,5%,1/10W,TP,1608
FR28 2007-007277 R-CHIP;392ohm,1%,1/10W,TP,1608
FR3 2007-000100 R-CHIP;68Kohm,5%,1/10W,TP,1608
FR30 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
4. Electrical Parts List

This Document can not be used without Samsung’s authorization.
Loc.No Part No Description ; Specification RemarkLoc.No Part No Description ; Specification Remark
4-2 Samsung Electronics
Electrical Parts List
FR31 2007-000134 R-CHIP;33Kohm,5%,1/10W,TP,1608
FR32 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
FR33 2007-000091 R-CHIP;12Kohm,5%,1/10W,TP,1608
FR34 2007-000134 R-CHIP;33Kohm,5%,1/10W,TP,1608
FR35 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
FR36 2007-000091 R-CHIP;12Kohm,5%,1/10W,TP,1608
FR37 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
FR39 2007-000087 R-CHIP;6.8Kohm,5%,1/10W,TP,1608
FR4 2007-000094 R-CHIP;22Kohm,5%,1/10W,TP,1608
FR41 2007-000082 R-CHIP;3.3Kohm,5%,1/10W,TP,1608
FR5 2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608
FR7 2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608
FR8 2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608
FR9 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
JACK2 3722-002097 JACK-PIN;7P+4P,Ni,BLK,ANGLE
KC1 2203-000440 C-CER,CHIP;1nF,10%,50V,X7R,TP,1608,-
KC2 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
KD1 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
KE1 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
KE2 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
KIC1 1203-001252 IC-VOL. DETECTOR;7545,TO-92,3P,-,PLASTIC
KIR1 AD32-00010A MODULE REMOCON;PIC-2604 SM1,37.9KHz,940n
KQ1 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
KQ2 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
KQ3 0501-000341 TR-SMALL SIGNAL;KSC1623-L,NPN,200mW,SOT-
KR1 2007-000077 R-CHIP;470ohm,5%,1/10W,TP,1608
KR10 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
KR11 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
KR12 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
KR13 2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608
KR2 2007-000102 R-CHIP;100Kohm,5%,1/10W,TP,1608
KR4 2007-000072 R-CHIP;47ohm,5%,1/10W,TP,1608
KR5 2007-000072 R-CHIP;47ohm,5%,1/10W,TP,1608
KR6 2007-000072 R-CHIP;47ohm,5%,1/10W,TP,1608
KR8 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
KR9 2007-000072 R-CHIP;47ohm,5%,1/10W,TP,1608
KSW1 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
KSW2 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
KSW3 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
KSW5 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
KSW6 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
KSW7 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
KSW8 3404-001164 SWITCH-TACT;12V DC,50MA,100GF,7X7X6.7MM,
LED1 0601-001587 LED;ROUND,RED,3.1MM,635NM
LED2 0601-000497 LED;ROUND,GRN,3.1mm,565nm
LED3 0601-000402 LED;ROUND,YEL,3X4.0MM,585NM,-
PBR11 3301-000297 BEAD-AXIAL;25ohm,3.6x1.2x5.7mm,,TP,,,
PBS01 AC27-92001M COIL-INDUCTOR;RH3.5X6.5RS,BEAD(RADIAL),-
PC1 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
PC3 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
PC4 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
PC5 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
PC6 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
PC8 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
PCD04 2201-000987 C-CERAMIC,DISC;2.2NF,20%,400V,Y5U,BK,12.
PCD05 2201-000987 C-CERAMIC,DISC;2.2NF,20%,400V,Y5U,BK,12.
PCD06 2201-000987 C-CERAMIC,DISC;2.2NF,20%,400V,Y5U,BK,12.
PCD07 2201-000987 C-CERAMIC,DISC;2.2NF,20%,400V,Y5U,BK,12.
PCD12 2201-000129 C-CERAMIC,DISC;0.1NF,10%,1KV,Y5P,TP,7X4M
PCF01 2305-001021 C-FILM,LEAD-PEF;100nF,20%,275V,TP,17.5x7
PCF02 2305-001021 C-FILM,LEAD-PEF;100nF,20%,275V,TP,17.5x7
PCNS2 3711-000178 CONNECTOR-HEADER;1WALL,2P,1R,3.96mm,STRA
PCR13 2301-000180 C-FILM,LEAD-PEF;18nF,0.05,100V,TP,7.2x4.
PCR14 2301-000417 C-FILM,LEAD-PEF;24nF,5%,50V,TP,6.5x10.5x
PCR15 2301-000423 C-FILM,LEAD-PEF;3.3nF,5%,100V,TP,7x10x4.
PCS32 2301-000129 C-FILM,LEAD-PEF;100nF,5%,50V,TP,10X9X4.3
PDR11 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
PDR12 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
PDS01 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
PDS02 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
PDS03 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
PDS04 0402-001196 DIODE-RECTIFIER;1T5,600V,1A,TS-1,TP
PDS11 0402-000012 DIODE-RECTIFIER;UF4007,1KV,1A,DO-41,TP
PDS31 0402-001195 DIODE-RECTIFIER;F1T4,400V,1.0A,TS-1,TP
PDS33 0402-001194 DIODE-RECTIFIER;UG2D,200V,2A,DO-204AC,TP
PDS34 0402-001438 DIODE-RECTIFIER;SHK55-65,60V,3A,AXIAL,BK
PDS51 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
PDS60 0401-000101 DIODE-SWITCHING;1N4148,100V,200mA,DO-35,
PE1 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
PE2 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
PE3 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
PE4 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
PE6 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
PEF10 2401-001681 C-AL;82uF,20%,200V,GP,TP,16x26,7.5m
PER12 2401-000905 C-AL;22UF,20%,16V,BP,-,6X11,5
PER13 2401-001235 C-AL;4.7uF,20%,250V,WT,TP,10x12.5,5
PES31 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
PES33 2401-003059 C-AL;1000UF,20%,16V,WT,TP,10X16,5
PES34 2401-000118 C-AL;1000uF,20%,10V,GP,TP,10x12.5,5
PES51 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
PES52 2401-000598 C-AL;1uF,20%,50V,GP,TP,4x7,5
PES54 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
PES57 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
PES58 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
PES59 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
PES60 2401-001254 C-AL;4.7uF,20%,35V,GP,TP,4x7,5
PES61 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
PFD01 3601-000194 FUSE-CARTRIDGE;250V,1A,FAST-ACTING,GLASS
PIC1 1203-002779 IC-VOLTAGE REGULATOR;G952T63U,SOT-223,3P
PICS1 0604-001028 PHOTO-COUPLER;TR,50-600%,250mW,DIP-4,ST
PICS2 AC14-12006D IC;KA431Z,TO-92,TAPING
PICS5 1203-002185 IC-VOLTAGE REGULATOR;3RD13,TO-220,4P,402
PL1 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
PL2 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
PL3 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
PLS01 AC29-00003A FILTER LINE NOISE;-,20mH MIN,-,-,-
PLS31 AC27-12001N COIL CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,-
PQR11 0502-000405 TR-POWER;KSC5039,NPN,70000MW,TO-220,BK,
PQR12 0501-000442 TR-SMALL SIGNAL;KTC3203-Y,NPN,400mW,T0-9
PQS58 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
PQS59 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
PQS60 0504-000142 TR-DIGITAL;KSR2001,PNP,300MW,4.7K/4.7K,T
PQS61 0501-000442 TR-SMALL SIGNAL;KTC3203-Y,NPN,400mW,T0-9
PQS62 0504-000118 TR-DIGITAL;KSR1003,NPN,300MW,22K/22K,TO-
PQS63 0501-000616 TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L
PR1 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
PRD11 2003-000119 R-METAL OXIDE;0.68ohm,5%,2W,AE,TP,6x16mm
PRD31 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
PRD32 2007-001157 R-CHIP;750ohm,5%,1/10W,TP,1608
PRR11 2003-002117 R-METAL OXIDE(S);330Kohm,5%,1W,AA,TP,3.3
PRR12 2003-000314 R-METAL OXIDE;47ohm,5%,2W,AE,TP,6x16mm
PRR13 2003-000314 R-METAL OXIDE;47ohm,5%,2W,AE,TP,6x16mm
PRR14 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
PRR15 2001-000003 R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm
PRR17 2001-000734 R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M
PRS12 2003-000994 R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x
PRS32 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
PRS33 2007-000259 R-CHIP;1.6Kohm,5%,1/10W,TP,1608
PRS34 2007-000491 R-CHIP;2.2KOHM,1%,1/10W,DA,TP,1608
PRS52 2001-000325 R-CARBON;120OHM,5%,1/8W,AA,TP,1.8X3.2MM
PRS55 2001-000062 R-CARBON;470OHM,5%,1/4W,AA,TP,2.4X6.4MM
PRS56 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

This Document can not be used without Samsung’s authorization.
Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark
Electrical Parts List
Samsung Electronics 4-3
PRS60 2001-000325 R-CARBON;120OHM,5%,1/8W,AA,TP,1.8X3.2MM
PRS61 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M
PTD1 AK26-00008A TRANS SWITCHING;EXINO,RCC,-,120V/230V,-,
PVA01 1405-000186 VARISTOR;470V,2500A,17.5x7.5mm,TP
PZR31 0403-001036 DIODE-ZENER;1N4745A,16V,5%,1W,DO-41,TP
PZS51 0403-000717 DIODE-ZENER;MTZJ5.1B,5.1V,4.94-5.2V,500m
PZS52 0403-000717 DIODE-ZENER;MTZJ5.1B,5.1V,4.94-5.2V,500m
PZS60 0403-001211 DIODE-ZENER;MTZJ12B,11.44-12.03V,500MW,D
RC10 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC11 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC12 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC13 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC14 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC15 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC16 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC17 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC18 2203-001052 C-CER,CHIP;0.56nF,10%,50V,X7R,TP,1608
RC19 2203-000815 C-CER,CHIP;0.033NF,5%,50V,C0G,TP,1608
RC2 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC20 2203-000491 C-CER,CHIP;2.2nF,10%,50V,X7R,TP,1608,-
RC21 2203-000491 C-CER,CHIP;2.2nF,10%,50V,X7R,TP,1608,-
RC22 2203-002041 C-CER,CHIP;0.47nF,10%,50V,X7R,TP,1608
RC23 2203-000491 C-CER,CHIP;2.2nF,10%,50V,X7R,TP,1608,-
RC24 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC25 2203-000491 C-CER,CHIP;2.2nF,10%,50V,X7R,TP,1608,-
RC28 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC29 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC30 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC31 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC32 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC33 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC34 2203-000440 C-CER,CHIP;1nF,10%,50V,X7R,TP,1608,-
RC35 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC36 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC37 2203-001662 C-CER,CHIP;5.6NF,10%,50V,X7R,TP,1608
RC4 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC5 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RC6 2203-001103 C-CER,CHIP;6.8nF,10%,50V,X7R,TP,1608,-
RC7 2203-001634 C-CER,CHIP;33nF,10%,50V,X7R,TP,1608,1.6m
RC8 2203-001607 C-CER,CHIP;0.22nF,5%,50V,NP0,TP,1608
RC9 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
RD1 0407-000116 DIODE-ARRAY;DAP202K,80V,100mA,CK2-3,SOT-
RE1 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
RE2 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
RE5 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
RIC1 AK13-00005B IC ASIC;SP3723CA0PM,EXINO2,64,5,+135,Q
RL1 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
RL2 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
RL3 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
RQ1 0501-000279 TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOT-
RQ2 0501-000279 TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOT-
RR1 2007-000312 R-CHIP;10ohm,5%,1/4W,TP,3216
RR10 2007-000234 R-CHIP;1.3Kohm,5%,1/10W,TP,1608
RR11 2007-000234 R-CHIP;1.3Kohm,5%,1/10W,TP,1608
RR12 2007-000234 R-CHIP;1.3Kohm,5%,1/10W,TP,1608
RR13 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
RR14 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
RR15 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
RR16 2007-000091 R-CHIP;12Kohm,5%,1/10W,TP,1608
RR17 2007-007549 R-CHIP;4.99Kohm,1%,1/10W,TP,1608
RR18 2007-000052 R-CHIP;10Kohm,1%,1/10W,TP,1608
RR2 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
RR3 2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608
RR4 2007-000312 R-CHIP;10ohm,5%,1/4W,TP,3216
RR5 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
RR7 2007-000381 R-CHIP;13Kohm,5%,1/10W,TP,1608
VC10 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC11 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC14 2203-000783 C-CER,CHIP;0.33NF,5%,50V,C0G,TP,1608
VC17 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC50 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC6 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC7 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC8 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VC9 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
VE1 2401-002165 C-AL;100uF,20%,16V,GP,TP,6.3x7,5
VE2 2401-000913 C-AL;22uF,20%,16V,GP,TP,5x11,5
VE4 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
VE5 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
VE6 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
VE7 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
VE8 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
VIC1 1204-001978 IC-VIDEO PROCESS;LA73054,-,36P,-,SSOP,7V
VJ5 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
VJ7 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
VL6 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
VR29 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
VR30 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
VR31 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
VR32 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
VR33 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
VR34 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
VR35 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZC10 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC11 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC12 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC13 2203-000426 C-CER,CHIP;0.018NF,5%,50V,C0G,TP,1608
ZC14 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC15 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC16 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC17 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC18 2203-000815 C-CER,CHIP;0.033NF,5%,50V,C0G,TP,1608
ZC19 2203-000815 C-CER,CHIP;0.033NF,5%,50V,C0G,TP,1608
ZC2 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC20 2203-000815 C-CER,CHIP;0.033NF,5%,50V,C0G,TP,1608
ZC21 2203-000815 C-CER,CHIP;0.033NF,5%,50V,C0G,TP,1608
ZC22 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC23 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC24 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC25 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC26 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC27 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC28 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC29 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC3 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC30 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC31 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC32 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC33 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC34 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC35 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC36 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC37 2203-000552 C-CER,CHIP;0.02NF,5%,50V,C0G,TP,1608
ZC39 2203-000552 C-CER,CHIP;0.02NF,5%,50V,C0G,TP,1608
ZC4 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC40 2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608
ZC41 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC42 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC43 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC44 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC45 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC46 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-

ZC47 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC48 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC5 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC6 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC7 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC8 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZC9 2203-005148 C-CER,CHIP;100nF,10%,16V,X7R,TP,1608,-
ZE1 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
ZE2 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
ZE3 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
ZE4 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5
ZE5 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
ZE6 2401-001479 C-AL;470uF,20%,10V,GP,TP,-,-
ZIC1 1204-002195 IC-DECODER;ZR36762,PQFP,208P,28x28mm,PLA
ZIC2 1105-001513 IC-DRAM;IS42S16400A-7T,1Mx16Bitx4Bit,T
ZIC3 1107-001369 IC-FLASH MEMORY;MBM29LV800BA-90PFTN,512K
ZIC5 1103-001204 IC-EEPROM;24C021,256x8Bit,SOP,8P,150MIL,
ZL1 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
ZL2 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
ZL3 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
ZL4 3301-001419 BEAD-SMD;-,220,-,500,TP,-,0.3
ZL5 3301-000314 BEAD-SMD;120ohm,1.6x0.8x0.8mm,150mA,,,,
ZL6 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
ZL8 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
ZL9 2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216
ZR10 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR11 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR12 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR13 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR14 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR15 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR16 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZR17 2007-007277 R-CHIP;392ohm,1%,1/10W,TP,1608
ZR18 2007-000113 R-CHIP;33ohm,5%,1/10W,TP,1608
ZR19 2007-000113 R-CHIP;33ohm,5%,1/10W,TP,1608
ZR2 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
ZR20 2007-000113 R-CHIP;33ohm,5%,1/10W,TP,1608
ZR21 2007-000113 R-CHIP;33ohm,5%,1/10W,TP,1608
ZR22 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608
ZR23 2011-000816 R-NET;100OHM,5%,1/16W,L,CHIP,8P,TP
ZR24 2007-000109 R-CHIP;1Mohm,5%,1/10W,TP,1608
ZR26 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
ZR27 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608
ZR28 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608
ZR3 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR35 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR36 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR38 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR4 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR45 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR46 2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608
ZR47 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR48 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR49 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR50 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR54 2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608
ZR7 2007-001101 R-CHIP;62ohm,5%,1/10W,TP,1608
ZR8 2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608
ZR9 2007-001164 R-CHIP;75ohm,1%,1/10W,TP,1608
ZY1 2801-003554 CRYSTAL-UNIT;27MHz,10ppm,28-AAM,12pF,40o
Loc.No Part No Description ; Specification Remark
4-4 Samsung Electronics
Electrical Parts List
Loc.No Part No Description ; Specification Remark
This Document can not be used without Samsung’s authorization.

This Document can not be used without Samsung’s authorization.Samsung Electronics 5-1
5. Block Diagram
DECK ASS'Y (DP-15)
FIC1
(FAN8004)
Actuator & Motor Driver
Spindle Motor
Pick-up & I/V Amp
Remote Control
Feed Motor
ZIC2 SDRAM
Coaxial
Yout
Cout
RIC1
(SP3723)
RF Amp & DPD
ZIC1 (Vaddis-6)
A/V Decoder
CVBS
R/Pr
B/Pb
G/Y
Lt
Rt
A/V
Decoder
AC3 &
MPEG 5.1
Video
Encoder
(4DAC)
AUDIO
DSP
CSS
INPUT
FIFO
&
DEMUX
AIC2 (PCM1742)
2-CH Audio DAC
6dB AMP
6dB AMP
Down-L/R
DTS Bitstream
Compo
Y/B/Pb
C/R/Pr
Comp/G/Y
ZIC5 2KBit EEROM
Post
Filter
Post Filter
IEC958/1937
Post Filter
VIC1
(LA73054)
Optical