Samsung 241MP - SyncMaster 241 MP User manual

LCD TV/MONITOR
SyncMaster211MP
SyncMaster241MP
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PC DISPLAY
PICTURE IN PICTURE (PIP)
PICTURE BY PICTURE (PBP)
TELETEXT

English-2
Information in this document is subject to change without notice.
© 2002 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung
Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the furnishing, performance, or
use of this material.
The Samsung logo is the registered trademarks of Samsung Electronics Co., Ltd.;
Microsoft, Windows®and Windows®NT are registered trademark of Microsoft
Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics
Standard Association. All other product names mentioned herein may be the trademarks
or registered trademarks of their respective owners.
Plug and Play
The adoption of the new VESA®Plug and Play solution eliminates complicated and time
consuming setup. It allows you to install your set in a Plug and Play compatible system
without the usual hassles and confusion. Your computer system can easily identify and
configure itself for use with your set.
Your set automatically tells the computer system its Extended Display Identification Data
(EDID) using Display Data Channel (DDC) protocols so the computer system can
automatically configure itself to use your set. If your PC system needs a monitor driver,
install monitor driver contained on the accompanied CD according to the operating
system your computer uses. For more information, refer to the driver installation
instructions included with your CD package.
PowerSaver
This set is EPA ENERGY STAR®compliant and NUTEK compliant when used with a
computer equipped with VESA DPMS functionality. For energy conservation, turn your set
Off when you are not using it or when leaving it unattended for long periods.

English-3
Caution
CAUTION:TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION The lightning flash and arrow head
within the triangle is a warning
sign alerting you of “dangerous
voltage” inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
WARNING: TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
☛The main voltage is indicated on the rear of your set and the frequency is 50 or 60 Hz.
Safety Instructions
These illustrations represent precautions concerning your set.
5°
10%
HH
40°
75%
Do NOT expose your set to
extreme temperature or
humidity conditions.
Do NOT expose your set to
direct sunlight.
Do NOT expose your set to
any liquids.
If your set is broken, do not try
to repair it yourself. Contact
qualified service personnel.
During storm conditions
(especially when there is
lightning) unplug your set from
the mains socket and aerial.
If the remote control is not
used for a long period of time,
remove the batteries and store
it in a cool, dry place.
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS

English-4
Contents
◆FOREWORD
■Safety Instructions .......................................................................................... 3
■Caution .......................................................................................................... 3
◆CONNECTING AND PREPARING YOUR TV/Monitor
■Viewing the Control Panel.............................................................................. 6
■Installing on the Wall ..................................................................................... 7
■Viewing the Connection Panel ....................................................................... 8
- Connecting an Aerial or Cable Television Network..................................... 9
- Connecting Computer................................................................................. 9
- Connecting DTV Set-Top Box, VCR, or DVD .............................................. 10
- Connecting External A/V Devices ............................................................... 10
- Connecting External Speakers ..................................................................... 10
- Connecting Speakers................................................................................... 10
■Viewing Pictures From External Sources ......................................................... 11
■Viewing the Remote Control (All Functions Except Teletext)........................... 12
■Viewing the Remote Control (Teletext Functions) ........................................... 13
■Inserting the Batteries in the Remote Control.................................................. 14
■Switching On and Off .................................................................................... 14
■Becoming Familiar with the Remote Control.................................................. 15
■Choosing Your Language ................................................................................ 16
◆SETTING THE CHANNELS
■Storing Channels Automatically...................................................................... 17
■Storing Channels Manually............................................................................. 18
■Giving Channels Names................................................................................. 19
■Skipping Unwanted Channels ........................................................................ 20
■Fine Tuning Channel Reception...................................................................... 20
■Sorting the Stored Channels ........................................................................... 21
◆USING THE VARIOUS FUNCTIONS
■Changing the Picture Standard ....................................................................... 22
■Adjusting the Picture Settings ......................................................................... 22
■Selecting the Picture Format........................................................................... 23
■Freezing the Current Picture........................................................................... 23
■Changing the Sound Standard ........................................................................ 24
■Adjusting the Sound Settings .......................................................................... 24
■Enjoying the Dolby Sound.............................................................................. 25

English-5
Contents
◆USING THE VARIOUS FUNCTIONS
■Switching the Internal Speakers On/Off.......................................................... 25
■Choosing the MTS (Multichannel Television Stereo) ....................................... 26
■Viewing the Picture In Picture (PIP) ................................................................ 27
■Viewing the Picture By Picture (PBP; Double Screen)..................................... 28
■Switching Off Automatically........................................................................... 29
■Displaying Information................................................................................... 29
◆USING THE PC FUNCTIONS
■Adjusting the Brightness and Contrast ............................................................ 30
■Selecting the Image Size................................................................................. 30
■Adjusting the Image Quality........................................................................... 31
■Changing the Image Position.......................................................................... 31
■Adjusting the Color ........................................................................................ 32
■Initializing the Image Settings......................................................................... 32
■Display Modes ............................................................................................... 33
■PowerSaver .................................................................................................... 33
◆USING THE TELETEXT FEATURE
■Teletext Feature .............................................................................................. 34
■Displaying the Teletext Information ................................................................ 34
■Selecting a Page by Number .......................................................................... 35
■Using FLOF to Select a Page .......................................................................... 36
■Storing Teletext Pages ..................................................................................... 36
◆RECOMMENDATIONS FOR USE
■Troubleshooting: Before Contacting Service Personnel ................................... 37
■Technical and Environmental Specifications................................................... 38
■Wiring the Mains Power Supply Plug (UK Only) ............................................ 39
☛➢
Press Important Note
Symbols

English-6
Viewing the Control Panel
ŒSource
Displays a menu of all of the available input
sources (TV/Video/S-Video/DVD/DTV/PC).
´PIP
Activates PIP (Picture-In-Picture)
ˇPBP
Activates PBP (Picture-By-Picture).
¨Menu
Opens the OSD and selects the function.
ˆExit
Exit from the on-screen menu.
Ø -
CH ❷❷+
Moves the selector up or down on the OSD.
Increases or decreases the channel number.
∏ -
❿❿VOL ➛➛+
Moves the selector left or right on the OSD.
Increases or decreases the level of audio volume
and the values of the selected function.
”Auto
Allows you experience the quality of displayed
picture. The values of fine, coarse and position are
adjusted automatically. (It works PC mode only.)
’(Power)
Turns ON/OFF your set.
Remote Control Sensor
Power Indicator

English-7
Installing on the Wall
1 Removing the Stand
Using a hexagonal wrench, remove the stand.
2 Removing Rubbers
Remove the four rubbers from the edges.
3 Mounting on the Wall
Mount the stand on the wall using screws or nails.
4 Fixing the Set
Using a hexagonal wrench, fix your set into the stand.
☛Installation Notes
◆Do not install your set on any place other than vertical
walls.
◆To protect the performance of your set and prevent
troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high
voltage.
- Do not install in the wall.
- Do not install near or around any heating apparatus.
◆Use only recommended parts and components.

English-8
Viewing the Connection Panel
S-VIDEO
VIDEO AUDIO (L) AUDIO (R)
AV JACK
SPK (R)
LR
AUDIO OUT
SPK (L)
AUDIO (ST)
VIDEO
PC
DC POWER SCART RF
1
2
3
4
5
6
6
7
☛Whenever you connect an audio or video system to your set,
ensure that all elements are switched off. Refer to the
documentation supplied with your equipment for detailed
connection instructions and associated safety precautions.
Power Input

English-9
Viewing the Connection Panel (continued)
ŒConnecting an Aerial or Cable Television Network (depending on the model)
To view television channels correctly, a signal must be received by the set from one of the following sources:
- An outdoor aerial
- A cable television network
- A satellite network
´Connecting Computer
- Connect the 15 Pin D-SUB connector to the PC video connector.
- Connect the stereo audio cable to ”Audio (ST)” on the rear of your set and the other end to “Audio Out” of
the sound card on your computer.
- If necessary, please install monitor driver contained on the accompanied CD. For more information, refer to
the driver installation instructions included with your CD package.
➣15 Pin D-SUB connector
Pin Separate H/V Composite H/V Sync-on-green
1 Red (R) Red (R) Red (R)
2 Green (G) Green (G) Green (G) + Horizontal/Vertical sync.
3 Blue (B) Blue (B) Blue (B)
4 Grounding Grounding Grounding
5 Grounding (DDC) Grounding (DDC) Grounding (DDC)
6 Red (R) Grounding Red (R) Grounding Red (R) Grounding
7 Green (G) Grounding Green (G) Grounding Green (G) Grounding
8 Blue (B) Grounding Blue (B) Grounding Blue (B) Grounding
9 No connection No connection Not used
10 Sync Grounding Sync Grounding Sync Grounding
11 Grounding Grounding Grounding
12 Data (DDC) Data (DDC) Data (DDC)
13 Horizontal sync. Horizontal/Vertical sync. Not used
14 Vertical sync. Not used Not used
15 Clock (DDC) Clock (DDC) Clock (DDC)

English-10
Viewing the Connection Panel
ˇConnecting DTV Set-Top Box, VCR, or DVD
- Connect the DTV, VCR, or DVD SCART cable to the SCART connector of the DTV, VCR, or DVD.
- If you wish to connect both the DTV Set-Top Box and VCR (or DVD), you should connect the DTV Set-Top
Box to the VCR (or DVD) and connect the VCR (or DVD) to your set.
¨Connecting External A/V Devices
- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD, or Camcorder.
- Connect RCA audio cables to “AUDIO (L)”and “AUDIO (R)”on the rear of your set and the other ends to
corresponding audio out connectors on the A/V device.
- Headphone may be connected to the headphone output (∏) on the rear of your set. While the headphone is
connected, the sound from the built-in speakers will be disabled.
ˆConnecting External Speakers
Connect RCA audio cables to amplifier built-in speakers (to take full advantage of the Surround sound effect).
ØConnecting Speakers (depending on the model)
or

English-11
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems,
you can view the different sources by selecting the appropriate input.
1Check that all the necessary connections have been made (refer to
pages 8 and 9 for further details).
2Switch your set on and if necessary, press the SOURCE button
repeatedly. The input sources are displayed in the following order:
Ant (TV) - Scart - Video - S-Video - PC.
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
LOCATE
-/--

English-12
Viewing the Remote Control (All Functions ExceptTeletext)
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
MENU
1 2 3
4 5 6
7 8 9
0
LOCATE
-/--
P
P
Numeric buttons for
direct channel access
Sound mode selection
Picture freeze
Picture size selection
Automatic switch-off
Television On/Off
Available sources selection
One/Two-digit channel selection
Previous channel
Exit from the OSD
Temporary sound switch-off
Picture effect selection Sound effect selection
Picture-In-Picture On/Off
Virtual Dolby menu display
Volume decrease
Next channel
Volume increase
➣The performance of the remote control may be affected by bright light.
Display the setting information
Self-adjust to the incoming
video signal
Menu display and
change confirmation
Previous channel
Picture-By-Picture
(Double screen)
PIP size selection
PIP location selection

English-13
Viewing the Remote Control (Teletext Functions)
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
MENU
1 2 3
4 5 6
7 8 9
0
LOCATE
-/--
P
P
Teletext hold
Teletext reveal
Teletext display/
mix both teletext information
and the norma l broadcast
Teletext store
Teletext previous page
Teletext mode selection
(List or Flof)
Teletext cancel
Teletext next page Programme selection by name
Teletext size selection
Teletext sub-page
Fastext topic selection

English-14
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase your set
◆ Find that the remote control is no longer operating
correctly
1Remove the cover on the rear of the remote control by pressing the
symbol downwards and then pulling firmly to remove it.
2Insert two R03, UM4, “AAA”1.5V or equivalent batteries taking care to
respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3Replace the cover by aligning it with the base of the remote control
and pressing it back into place.
➣Do not mix battery types, i.e. alkaline and monganese.
Switching On and Off
The mains lead is attached to the rear of your set.
☛If you have purchased this set in the United Kingdom, refer to
page 39 for further instructions on plug wiring.
Plug the mains lead into an appropriate socket.
Result:
The screen is turned on and a green Standby indicator appears
on the front of your set.
Your set can be placed in Standby mode, in order to reduce the power
consumption.
The Standby mode can be useful when you wish to interrupt viewing
temporarily (during a meal, for example).
1Press the Power ( ) button on the remote control or the front of your
set.
Result:
The screen is turned off and a green Standby indicator
disappears on the front of your set.
2To switch your set back on, simply press the Power ( ) button again.
➣Do not leave your set in Standby mode for long periods of time
(when you are away on holiday, for example). Turn your set off by
unpluging from the mains and aerial.
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
LOCATE
-/--

English-15
Becoming Familiar with the Remote Control
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Set up your set using the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button Viewing Function Menu Function
▲ Used to display the next Used to select the previous
Pstored channel. menu option.
PUsed to display the Used to select the next menu
▼ previous stored channel. option.
PRE-CH Used to switch repeatedly between the last two channels
displayed. (PRE-CH; Previous Channel)
to Used to display the corresponding channels.
-/-- Used to select a channel numbered ten or over.
Press this button, and the “
-- ”symbol is displayed.
Enter the two-digit channel number.
Used to decrease the Used to...
volume. ◆Display a submenu containing
selections for the current
menu option.
◆Search forwards manually
for channels
◆Reduce a menu option value.
Used to increase the Used to...
volume. ◆Display a submenu containing
selections for the current
menu option.
◆Search backwards manually
for channels
◆Increase a menu option value.
MUTE Used to switch the sound off temporarily.
➣To turn the sound back on, press this button again, or
press the
- or +button.
MENU Used to display the Used to return to the previous
on-screen menu system. menu or normal viewing.
EXIT Used to exit from the menu system and return to normal
viewing directly.
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
LOCATE
-/--
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
LOCATE
-/--
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
9
LOCATE
-/--
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
0
LOCATE
-/--
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
MENU
1 2 3
4 5 6
7 8 9
0
LOCATE
-/--
P
P

English-16
Choosing Your Language
When you start using your set for the first time, you must select the
language which will be used for displaying menus and indications.
1Press the MENU button.
Result:
The main menu is displayed.
2Press the P▼or P▲button to select the Function.
Result:
The options available in the Function group are
displayed.
3Press the - or +button .
4Press the P▼or P▲button to select the Language .
5Select a particular language by pressing the - or +button
repeatedly.
6When you are satisfied with your choice, press the EXIT button to
return to normal viewing.
Function
Sleep Timer à Off ¨
PIP ¨
PBP ¨
Language à English ¨
HOLD DUAL I/II LIST/FLOF CANCEL
SLEEP SUBPAGE SIZE PIP
P.SIZE PBP
ON
TTX/MIX V.DOLBY
PRE-CH
EXITMUTE
SOURCE AUTO DISPLAY STILL
P.STD S.STD
Power
MENU
LOCATE
-/--
P
P

English-17
Storing Channels Automatically
You can scan for the frequency ranges available to you (and
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers. However you can sort numbers manually and
clear any channels you do not wish to watch.
1Press the MENU button.
Result:
The main menu is displayed.
2Press the P▼or P▲button to select the Channel.
Result:
The options available in the Channel group are displayed.
3Press the - or +button.
Result:
The Auto store is selected.
4Press the - or +button again.
Result:
The options available in the Auto store group are
displayed with the
Country is selected.
5Select your country by pressing the - or +button repeatedly.
The following countries are available:
Belgie - Deutschland - Espania - France - Italia - Nederland
- Schweiz - Sverige - UK - East Europe.
6Press the P▼or P▲button to select the Search, and then press the
- or +button.
Result:
The search will end automatically. Channels are sorted
and stored in an order which reflects their position in the
frequency range, (with lowest first and highest last). The
programme originally selected is then displayed.
➣
To stop the search before it has finished, press the EXIT button.
7When the channels have been stored, you can:
◆Change channels
◆Assign a name to the stored channels (refer to page 19)
◆Clear a channel (refer to page 20)
◆Fine tune channel reception if necessary (refer to page 20)
◆Sort them in the order required (refer to page 21)
Channel
Auto store ¨
Manual store ¨
Name ¨
Add/Erase ¨
Fine tune ¨
Channel sort ¨
Channel
Country à UK ¨
Search ¨
Channel
Country à UK ¨
Search ¨
Search
Program 1
Frequency 205MHz
Band VHF-H

English-18
Storing Channels Manually
You can store up to 100 channels, including those received via cable
networks. When storing channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The programme number of each stored channel which you
wish to identify
1Press the MENU button.
Result:
The main menu is displayed.
2Press the P▼or P▲button to select the Channel.
Result:
The options available in the Channel group are displayed.
3Press the - or +button .
4Press the P▼or P▲button to select the Manual store . Press the
- or +button.
Result:
The options available in the Manual store group are
displayed with the
Color system is selected.
5If necessary, indicate the broadcasting standard required by pressing
the
- or +button repeatedly.
Result: The color standards are displayed in the following order:
AUTO - PAL - SECAM - NT4.43.
6Press the P▼or P▲button to select the Sound system. Indicate the
sound standard required by pressing the
- or +button
repeatedly.
Result: The sound standards are displayed in the following order:
BG - DK - I - L.
7If you know the channel number to be stored, press the P▼or P▲
button to select the Channel. Indicate the required number by
pressing the
- or +button.
If you do not know the channel numbers, press the P▼or P▲button
to select the Search. Start the search by pressing the - or +
button.
Result: The tuner scans the frequency range until the first
channel or the channel that you selected is received on
your screen.
8To assign a programme number to a channel, select the Program by
pressing the P▼or P▲button. Press the
- or +button to
find the correct number.
9Press the P▼or P▲button to select the Store . Select the OK by
pressing the
- or +button .
Result: The channel and associated programme number are
stored.
10 Repeat Steps 7to 9for each channel to be stored.
Channel
Auto store ¨
Manual store ¨
Name ¨
Add/Erase ¨
Fine tune ¨
Channel sort ¨
Channel
Color system à AUTO ¨
Sound system à BG ¨
Search ¨ 0MHz
Channel C 1
Program P 1
Store ?
Channel
Color system à AUTO ¨
Sound system à BG ¨
Search ¨ 0MHz
Channel C 1
Program P 1
Store ?
Channel
Color system à AUTO ¨
Sound system à BG ¨
Search ¨ 0MHz
Channel C 1
Program P 1
Store ?
Channel
Color system à AUTO ¨
Sound system à BG ¨
Search ¨ 0MHz
Channel C 1
Program P 1
Store ?
Channel
Color system à AUTO ¨
Sound system à BG ¨
Search ¨ 0MHz
Channel C 1
Program P 1
Store ?
Channel
Color system à AUTO ¨
Sound system à BG ¨
Search ¨ 0MHz
Channel C 1
Program P 1
Store OK

English-19
Giving Channels Names
If channel name information is broadcast when you store the channels
either manually or automatically, the names are assigned to the
channels directly. You can however change these names or assign new
names as required.
1Press the MENU button.
Result:
The main menu is displayed.
2Press the P▼or P▲button to select the Channel.
Result:
The options available in the Channel group are displayed.
3Press the - or +button .
4Press the P▼or P▲button to select the Name . Press the - or
+button.
Result:
The current channels are displayed.
5If necessary, select the channel to be assigned to a new name by
pressing the P▼or P▲button.
6Press the - or +button.
7Press the P▼or P▲button to select a letter (A~Z), a number(0~9)
or a symbol (
- , space). Move on the previous or next letter by
pressing the
- or +button.
8Repeat Steps 5to 7for each channel to be assigned to a new
name.
Channel
Auto store ¨
Manual store ¨
Name ¨
Add/Erase ¨
Fine tune ¨
Channel sort ¨
Channel
P 1
P 2
P 3
P 4
Channel
P 1 A
P 2
P 3
P 4

English-20
Skipping Unwanted Channels
You can exclude the channels you chosen from the channels you
scanned. When you scan through the stored channels, those you have
chosen to skip are not displayed.
All channels that you do not specifically choose to skip are displayed
during scanning.
1Press the MENU button.
Result:
The main menu is displayed.
2Press the P▼or P▲button to select the Channel.
Result:
The options available in the Channel group are displayed.
3Press the - or +button.
4Press the P▼or P▲button to select the Add/Erase . Press the -
or +button.
Result:
The stored channels are displayed.
5Press the P▼or P▲button to select the channel to add or erase.
If necessary, select the Added or Erased by pressing the
- or
+button.
6Repeat Step 5for each channel to be added or erased.
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine-tune the channel,
as this is done automatically during the search and store operation.
If however the signal is weak or distorted, you may have to fine-tune
the channel manually.
1Press the MENU button.
Result:
The main menu is displayed.
2Press the P▼or P▲button to select the Channel.
Result:
The options available in the Channel group are displayed.
3Press the - or +button .
4Press the P▼or P▲button to select the Fine tune.
5Obtain a sharp and clear picture and good sound quality by pressing
the
- or +button.
Channel
Auto store ¨
Manual store ¨
Name ¨
Add/Erase ¨
Fine tune ¨
Channel sort ¨
Fine tune
7
Channel
Auto store ¨
Manual store ¨
Name ¨
Add/Erase ¨
Fine tune ¨
Channel sort ¨
Channel
P 1 Added
P 2 Added
P 3 Added
P 4 Added
Channel
P 1 Erased
P 2 Added
P 3 Added
P 4 Added