Samsung LH008IWJ Series User manual

Samsung Electronics
LED Display
Installation Manual
LH008IWJ*** (P0.84)
SNOW-18010U
Ver. 1.4

Samsung Electronics
Check first before Installation (1/2)
1
•For HDBT signal stability, use the cable above CAT6 *STP, *FTP level. ( Length 15m~100m )
-Do not use “comb” or “pinstripe” cable. “CAT6 UTP can not be allowed”
•All Power cables and OCM cable must be connected firmly
•Do not mix cabinet which have different Project number, each cabinet have its own project
number.
Module Cabinet Box

Samsung Electronics
Check first before Installation (2/2)
2
•Install the device only using SNOW-1810U and its supplied IG.
※ Please check below Cabinet and S-box compatibility table information
S-Box SNOW-1810U SNOW-1703ULD SNOW-1703U
I/G BN91-20525A BN91-19993A BN91-19100A
Cabinet IF015H,
IF020H,
IF025H,
IF025H-D,
IF040H-D,
IF060H-D,
IF012J,
IW008J
IF015H,
IF020H,
IF025H,
IF025H-D,
IF040H-D,
IF060H-D,
IF012J
IF015H,
IF020H,
IF025H,
IF025H-D,
IF040H-D,
IF060H-D

Samsung Electronics
Table of Contents
1. Product Information and Precautions for Installation
2. Check Point about the Radiant Heat
3. Preparation for Cabinet Installation
4. Frame Installation
5. Cabinet + Frame Installation
6. Disassembly & Front Service
7. S-BOX Installation and Connection
8. Settings and How to Use
9. Issue and Solution
10. Cable Connection
11. Bezel Installation
3

Samsung Electronics
Fig.3 S-Box Fig.4 I/G
(Interface Gender)
◇Frame Kit Composition (Refer to Page 16)
1. Product Information and
Precautions for Installation
Frame Kit Composition Note
VG-LFJ08SWW 1x1 (1 Set) -
VG-LFJ08FWW 2x2 (4 Set) FHD Installation
VG-LFJ08TWW 3x3 (9 Set) -
VG-LFJ08UWW 4x4 (16 Set) UHD Installation
◇SBB-SNOWJAU (S-Box, I/G)
◇Cabinet Product Information
4
<1x1> <2x2> <3x3> <4x4>
※ Power system should be designed
according to Screen composition. 1 FHD
Screen should be in same power system.
(Refer to page 19 )

Samsung Electronics
◇Storage Condition
1. Product Information and
Precautions for Installation
5
◇Pre-heating Process
should be conducted before installation& operation after storage. (refer to page 18)
Condition Value Recommend
Temperature -20℃~ +45℃-20℃~ +45℃
Humidity 5~95% 5~65%
Hight 3000m 3000m
Step condition Brightness Time
1 Lighting up display with 10 gray scale 5% 2 hr
2 Lighting up display with 20 gray scale 8% 2 hr
3 Lighting up display with 30 gray scale 10% 2 hr
4 Lighting up display with 40 gray scale 15% 2 hr
5 Lighting up display with 50 gray scale 20% 2 hr
6 Lighting up display with 70 gray scale 25% 2 hr
7 Lighting up display with 90 gray scale 35% 2 hr
8 Lighting up display with 120 gray scale 45% 2 hr
9 Lighting up display with 150 gray scale 60% 2 hr
10 Lighting up display with 180 gray scale 70% 2 hr
11 Lighting up display with 200 gray scale 80% 2 hr
12 Lighting up display with 255 gray scale 100% 2 hr

Samsung Electronics
1. Product Information and
Precautions for Installation
• Precautions for Installation (LED damage)
6
Caution Image
[ Beware of Outside Impact, Fall]
①Beware not to cause any impact on the LED screen or drop the product on the floor
after the protection gets taken off for installation.
②Beware not to put the LED side headed downwards to the floor after the protection
gets taken off for installation.
③Beware not to have the corner area of LED module be damaged due to the contact
with the outside.
④
Beware not to put more than 12 layers.
①
②
③
④
[Beware of LED Damage due to Static Electricity]
▶
Beware not to touch LED screen with bare hands without putting gloves on.
[Beware of LED & Film Damage due to Metallic Substances]
▶
Beware not to have metallic substances pulled in to the surface
due to the magnetic force on the front side of the LED.
▶
If any metallic substances get drawn in on the surface, please disassemble the
module and then remove the pollutants by using a magnet.
[Beware of LED Damage due to chemicals.]
▶
Beware not to contact water, waxes, benzene, thinners, mosquito repellents,
lubricants, cleaners, solvents or surfactants on LED.
▶
When installing on the construction site, it should be installed after construction & cleaning.
▶
If the installation site requires construction work, the product is covered with a
curtain and operated 50% white or video for 2 hours every day.
MODULE
Front
LED &
Film

Samsung Electronics
1. Product Information and
Precautions for Installation
◇Caution for cleaning screen
7
- Wipe lightly with the soft cleaning cloth provided with the product
(Watch out for surface LED damage)
- Hard stuff on screen surface can damage LED chip and film during cleaning.
Clear screen surface before cleaning
- Watch out for damage when cleaning gap between Half-
Cabinets
- Watch out for damage when cleaning gap between Modules
- Do not insert any cleaning tool or spay cleaner directly into
the gap
- Do not wipe the LED surface with hard materials such as
paper towels, brushes comb or brush, acrylic or steel.
- Do not use chemicals such as wax, benzene, cinna, mosquito
repellent, air freshener, lubricant, and detergent in products
(Recommendation: Use of glass detergent for alcohol or
surfactant)
★Caution★

Samsung Electronics
1. Product Information and
Precautions for Installation
•Preparations for Installation
8
MAGNET JIG
(BN81-17114A)
(-) (+) driver
Absorber
(BN81-17124A)
Adjustment tool
(BN81-17112A) GAP-TOOL
(BN81-17113A)
Glove
(RA00400E-002539)
Hex Wrench
2mm, 6mm PLIER
(BN81-17541A)
•Provided in Frame Kit. (VG-LFJ08*WW).
•Provided in accessory kit. (CY-WJJPWP).

Samsung Electronics
2. Check Point about the Radiant Heat
9
Standard and condition for indoor installation
-Standard for using ‘SAMSUNG WALL MOUNT’ (Fulfill ADA)
∙The gap between the front of a product and a wall: 98.6mm
∙The gap between the back of a product and a wall: 26.1mm
-When sunlight enters
∙If a sunlight enters through a window or outside walls of a building,
an additional inquiry is needed.
-The effect of warm/cold air from a duct system
∙Make sure the warm/cold breeze(especially warm air) from a duct system not to affect a product.
-The measuring location for ambient temperature
∙Either right in the center of a product or Air inlet part
※ ADA(American’s with Disabilities Act
98.6mm
26.1mm
wall
Measuring
location for
ambient
temperature
Measuring
location for
ambient
temperature
※ Written under ‘Full white, (back light 7)’ standard
Written under ‘Video, (back light 10)’ standard
◇Ventilation Guide