Samsung SMC-210 User manual

CCTV COLOR MONITOR
SMC-210/210N/210P (21-INCH)
SMC-144/144N/144P (14-INCH)
SMC-142/142N/142P (14-INCH)
SMC-140/140N/140P (14-INCH)
SMC-102/102N/102P (10-INCH)
SMC-100/100N/100P (10-INCH)
SMP-152/152N/152P (15-INCH)
SMP-150/150N/150P (15-INCH)
SERVICE
1. Precautions
2. Alignment and Adjustment
3. Exploded View and Parts List
4. Electrical Parts List
5. Schematic Diagrams
Manual
CCTV COLOR MONITOR CONTENTS
JUN. 1999
Printed in Korea
AB68-00060A
SERVICE MANUAL SMC-210/144/142/140/102/100/SMP-152/150

1-1
1. Precautions
Follow these safety,servicing and ESD precautions to prevent damage and protect against potential hazards such
as electrical shock and X-rays.
1-1 Safety Precautions
1) Be sure that all of the built-in protective devices are
replaced. Restore any missing protective shields.
2) When reinstalling the chassis and its assemblies, be
sure to restore all protective devices, including :
nonmetallic control knobs and compartment cov-
ers.
3) Make sure that there are no cabinet openings
through which people-particularly children-might
insert fingers and contact dangerous voltages.
Such openings include the spacing between the
picture tube and the cabinet mask, excessively
wide cabinet ventilation slots, and improperly
fitted back covers.
If the measured resistance is less than 1.0 megohm
or greater than 5.2 megohms, an abnormality exists
that must be corrected before the unit is returned
to the customer.
4) Leakage Current Hot Check(Fig. 1-1):Warning:Do
not use an isolation transformer during this test.
Use a leakage-current tester or a metering system
that complies with American National Standards
Institute(ANSI C101.1, Leakage Current for
Appliances),and Underwriters Laboratories(UL
Publication Ul1410, 59.7).
DEVICE
UNDER
TEST
TESTALL
EXPOSED METAL
SURFACES
3-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
LEAKAGE
CURRENT
TESTER
(READING SHOULD
NOT BE ABOVE
0.5mA)
EARTH
GROUND
Fig. 1-1 Leakage Test
5) With the unit completely reassembled, plug the AC
line cord directly the power outlet. With the unit’s
AC switch first in the ON position and the OFF,
measure the current between a known earth
ground(metal water pipe,conduit,etc.)and all
exposed metal parts, including:antennas, handle
brackets,metal cabinets,screwheads and control
shafts. The current measured should not exceed
0.5milliamp. Reverse the power-plug prongs in the
AC outlet and repeat the test.
6) Antenna Cold Check:
With the unit’s AC plug disconnected from the AC
source, connect an electrical jumper across the two
AC prongs. Connect one lead of the ohmmeter to
an AC prong. Connect the other lead to the coaxial
connector.
7) X-ray Limits:
The picture tube is especially designed to prohibit
X-ray emissions. To ensure continued X-ray protec-
tion, replace the picture tube only with the one that
is the same type as the original. carefully reinstall
the picture tube shields and mounting
hardware;these also provide X-ray protection.
8) High Voltage Limits:
High voltage must be measured each time servic-
ing is done on the B+,horizontal deflection or high
voltage circuits. Correct operation of the x-ray pro-
tection circuits must be reconfirmed whenever they
are serviced. (X-ray protection circuits also may be
called “horizontal disable” or “hold-down”.)
Heed the high voltage limits. These include the X-
ray protection Specifications Label, and the
Product Safety and X-ray Warning Note on the ser
vice data schematic.
9) High voltage is maintained within specified limits
by close tolerance, safety-related components and
adjustments. If the high voltage exceeds the speci-
fied limits, check each of the special components.

Precautions
1-2
10) Design Alteration Warning:
Never alter or add to the mechanical or electrical
design of this unit. Example:Do not add auxiliary
audio or video connectors Such alterations might
create a safety hazard. Also, any design changes
or additions will void the manufacturer’s warran-
ty.
11) Hot Chassis Warning:
Some TV receiver chassis are electrically connect-
ed directly to one conductor of the AC power
cord. If an isolation transformer is not used, these
units may be safely serviced only if the AC power
plug is inserted so that the chassis is connected to
the ground side of the AC source.
To confirm that the AC power plug is inserted
correctly, do the following:Using an AC voltmeter,
measure the voltage between the chassis and a
known earth ground. If the reading is greater
than 1.0V, remove the AC power plug, reverse its
polarity and reinsert. Re-measure the voltage
between the chassis and ground.
12) Some TV chassis are designed to operate with 85
volts AC between chassis and ground, regardless
of the AC plug polarity.
These units can be safely serviced only if an isola-
tion transformer inserted between the receiver
and the power source.
13) Some TV chassis have a secondary ground system
in addition to the main chassis ground. This sec-
ondary ground system is not isolated from the
AC power line. The two ground systems are elec-
trically separated by insulating material that must
not be defeated or altered.
14) Components, parts and wiring that appear to
have overheated or that are otherwise damaged
should be replaced with parts that meet the origi-
nal specifications. Always determine the cause of
damage or overheating, and correct any potential
hazards.
15) Observe the original lead dress, especially near
the following areas: Antenna wiring, sharp edges,
and especially the AC and high voltage power
supplies. Always inspect for pinched, out-of-
place, or frayed wiring. Do not change the spac-
ing between components and the printed circuit
board. Check the AC power cord for damage.
Make sure that leads and components do not
touch thermally hot parts.
16) Picture Tube Implosion Warning:
The picture tube in this receiver employs “inte-
gral implosion” protection. To ensure continued
implosion protection, make sure that the replace-
ment picture tube is the same as the original.
17) Do not remove, install or handle the picture tube
without first putting on shatterproof goggles
equipped with side shields. Never handle the pic-
ture tube by its neck. Some “in-line” picture tubes
are equipped with a permanently attached deflec-
tion yoke; do not try to remove such “permanent-
ly attached” yokes from the picture tube.
18) Product Safety Notice:
Some electrical and mechanical parts have special
safety-related characteristics which might not be
obvious from visual inspection. These safety fea-
tures and the protection they give might be lost if
the replacement component differs from the origi-
nal-even if the replacement is rated for higher
voltage, wattage, etc.
Components that are critical for safety are indicat-
ed in the circuit diagram by shading, ( ) or ( ).
Use replacement components that have the same
ratings, especially for flame resistance and dielec-
tric strength specifications. A replacement part
that does not have the same safety characteristics
as the original might create shock, fire or other
hazards.

Precautions
1-3
1-2 Servicing Precautions
1) Servicing precautions are printed on the cabinet.
Follow them.
2) Always unplug the unit’s AC power cord from the
AC power source before attempting to:(a) Remove
or reinstall any component or assembly, (b)
Disconnect an electrical plug or connector, (c)
Connect a test component in parallel with an elec-
trolytic capacitor.
3) Some components are raised above the printed cir-
cuit board for safety. An insulation tube or tape is
sometimes used. The internal wiring is sometimes
clamped to prevent contact with thermally hot
components. Reinstall all such elements to their
original position.
4) After servicing, always check that the screws, com-
ponents and wiring have been correctly reinstalled.
Make sure that the portion around the serviced part
has not been damaged.
Warning 1 : First read the “Safety Precautions”section of this manual. If some unforeseen circumstance creates a conflict
between the servicing and safety precautions, always follow the safety precautions.
Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.
5) Check the insulation between the blades of the AC
plug and accessible conductive parts(examples :
metal panels, input terminals and earphone jacks).
6) Insulation Checking Procedure:Disconnect the
power cord from the AC source and turn the
power switch ON. Connect an insulation resistance
meter(500V) to the blades of the AC plug.
The insulation resistance between each blade of the
AC plug and accessible conductive parts(see
above) should be greater than 1 megohm.
7) Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit(or any of its
assemblies) unless all solid-state heat sinks are cor-
rectly installed.
8) Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrument’s
ground lead last.
1-3 Precautions for Electrostatically Sensitive Devices (ESDS)
1) Some semiconductor(“solid state”) devices are easily
damaged by static electricity.
Such components are called Electrostatically
Sensitive Devices(ESD); examples include integrated
circuits and some field-effect transistors. The follow-
ing techniques will reduce the occurrence of compo-
nent damage caused by static electricity.
2) Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-
strap device.(Be sure to remove it prior to applying
power-this is an electric shock precaution.)
3) After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of electrostatic charge.
4) Do not use freon-propelled chemicals.
These can generate electrical charges that damage
ESDs.
5) Use only a grounded-tip soldering iron when
soldering or unsoldering ESDs.
6) Use only an anti-static solder removal device.
Many solder removal devices are not rated as “anti-
static”; these can accumulate sufficient electrical
charge to damage ESDs.
7) Do not remove a replacement ESD from its protec-
tive package until you are ready to install it. Most
replacement ESDs are packaged with leads that are
electrically shorted together by conductive foam,
aluminum foil or other conductive materials.
8) Immediately before removing the protective materi-
al from the leads of a replacement ESD, touch the
protective material to the chassis or circuit assembly
into which the device will be installed.
9) Minimize body motions when handling unpackaged
replacement ESDs. Motions such as brushing clothes
together, or lifting a foot from a carpeted floor can
generate enough static electricity to damage an ESD.

2-1
ŒLion Head Pattern Generator.
´Color Bar, White, Cross Pattern Generator.
ˇColor Analyzer.
¨Oscilloscope Scope.
2. Alignment and Adjustment
2-1 Measuring Instruments
2-2 Connection Status and Aging
ŒInput Color Bar in CAMERA 1 (Video A).
´Input Lion Head in CAMERA 2 (Video B).
ˇAging for 30minutes before Adjustment.
2-3 Focus Adjustment
ŒInput a Cross Signal.
´Adjust focus VR (FBT) to obtain the clearest display at CRT center.
2-4 Screen Adjustment
ŒInput any pattern in CAMERA 1 (Video A).
´Adjust screen VR (FBT) to obtain normal display without Blooming or Filback line.
2-5 Adjustment for Factory and Service Mode
Œ´ˇ¨ˆØ∏”’˝Ô
Models Factory Mode Menu UP Menu Down Menu Select Menu Select Sub Menu Factory
& Data Up & Data Down Exit Mode Exit
SMC-102 ¨ ” Œ ´ ∏ Ø Ø
The Other ” ∏ Œ ´ Ø ˆ ˆ
Models
ˇ ˆ ∏ ∏
∏ ” ” ”
ˇ ¨ Ø Ø
Ø ∏ ∏ ∏

2-2
Alignment and Adjustment
2-5-1 Adjustment Mode
Set the data as table using control key.
MAIN ADJUSTMENT PARAMETER
FUNCTION OSD RANGE ADJUST DATA REMARK
SUB BRIGHT SBT 0 ~ 13 STEP 7
SUB CONTRAST SCT 0 ~ 13 STEP 7
SUB COLOR SCR 0 ~ 23 STEP 11
S-CORRECTION SC 0 ~ 63 STEP 10
RED CUTOFF RG 0 ~ 63 STEP 31
GREEN CUTOFF GG 0 ~ 63 STEP 31
BULE CUTOFF BG 0 ~ 63 STEP 31
PAL VERTICAL SLOPE PSL 0 ~ 63 STEP 25
PAL VERTICAL SHIFT PVS 0 ~ 63 STEP 32
PAL VERTICAL AMP PVA 0 ~ 63 STEP 32
PAL HORIZONTAL SHIFT PHS 0 ~ 63 STEP 32
NTSC VERTICAL SLOPE NSL 0 ~ 63 STEP 25
NTSC VERTICAL SHIFT NVS 0 ~ 63 STEP 32
NTSSC VERTICAL AMP NVA 0 ~ 63 STEP 32
NTSC HORIZONTAL SHIFT NHS 0 ~ 63 STEP 32
It is possible to choose PSL, PVS, PVA, PVH when PAL signal inputted.
It is possible to choose NSL, NVS, NVA, NVH when NTSC signal inputted.
Note
2-5-2 Test Pattern (Aging Mode)
ΠThese test pattern are used in Service and Aging.
 RED
 GREEN
 BLUE
 WHITE
´Choose White at Aging.
ˇChoose R.G.B at Purity Adjustment.
2-5-3 Option Byte
ΠAdjust option byte as right Byte 0 : 00
Byte 1 : 00
2-5-4 Data Save and Exit
ΠPress Factory Mode Exit Key Twice to exit from factory mode.

Alignment and Adjustment
2-3
2-6 White Balance Adjustment
2-6-1 High-Light Adjustment
ŒInput Lion Head and White Pattern.
´Aging over 30 minutes.
ˇCheck a data in factory mode.
¨Cheak whether RG, GG and BG are 31 or not.
ˆAdjust RG, BG to obtain X=290, Y=300.
2-6-2 Low-Light Adjustment
ΠIt is not necessary to adjust Low-Light.
When High-Light is adjusted, Low-Light is simultaneously adjusted.
2-7 Geometry Adjustment (When NTSC Signal Inputted)
(SC NVL NVS NVA NHS)
ŒInput Lion Head Pattern.
´Set SC data 10 or 11 at factory mode.
ˇAdjust NSL to be round a lower side like a upper side.
¨Adjust NVS until the display is located at vertical center.
30
30
30
30
30
2
531 135
1
3
5
1
3
5
20
25
325
575
525 LINE
50
20
25
30
35
300
10
65
4
4
54 5
5
4
7
7
6
7
6
6
7
5
6
7
8
02
3
3
3
4
5
543
30
35
35
30
25
20
25
20
35
30
VERTICAL CENTER
ˆAdjust NVA until the Top and Bottom of the display ro be 4.
30
30
30
30
30
2
531 135
1
3
5
1
3
5
20
25
325
575
525 LINE
50
20
25
30
35
300
10
65
4
4
54 5
5
4
7
7
6
7
6
6
7
5
6
7
8
02
3
3
3
4
5
543
30
35
35
30
25
20
25
20
35
30
4

2-4
Alignment and Adjustment
ØAdjust NVS until the display is located at horizontal center.
HORIZONTAL CENTER
30
30
30
30
30
2
531 135
1
3
5
1
3
5
20
25
325
575
525 LINE
50
20
25
30
35
300
10
65
4
4
54 5
5
4
7
7
6
7
6
6
7
5
6
7
8
02
3
3
3
4
5
543
30
35
35
30
25
20
25
20
35
30
∏Adjust H-Size (LW01) at Main Board until the right and left of the display to be 5. (SMP-152/150 Only)
30
30
30
30
30
2
531 135
1
3
5
1
3
5
20
25
325
575
525 LINE
50
20
25
30
35
300
10
65
4
4
54 5
5
4
7
7
6
7
6
6
7
5
6
7
8
02
3
3
3
4
5
543
30
35
35
30
25
20
25
20
35
30
5
RE. : Adjust PSL, PVS, PVA and PHS when input PAL signal.

3-1
3. Exploded View and Parts List
3-1 SMC-210/210N/210P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-2 SMC-144/144N/144P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-3 SMC-142/142N/142P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-4 SMC-140/140N/140P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-5 SMC-102/102N/102P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-6 SMC-100/100N/100P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-7 SMP-152/152N/152P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3-8 SMP-150/150N/150P - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Page
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9

Exploded Views and Parts List
3-2
3-1 SMC-210/210N/210P
S.N.A.
¨
∏
S.N.A.
S.N.A.
S.N.A.
∏

Ò
∏S.N.A.
S.N.A.
S.N.A. ˆ
Œ
´
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
∏
S.N.A.
Ô
’
˝
S.N.A.
∏
Ø
∏
Ø
S.N.A.
”
ˇ
S.N.A. : Service Not Available
S.N.A.
1 AB92-90601B ASSY-CRT;SCM-21MK,A51KQJ63X01(U),21’ 2 AB91-00547A ASSY-MAIN 3 3001-001071 SPEAKER;5W,8ohm 90dB,180Hz 4 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 AB60-10601E SCREW-SPEUAL;BH,+,B,M3,L19,ZPC(YEL) 9 AB60-10601C SCREW-ASSY TAPP;RWH,+,2,M4 12,ZPC(YEL),S 10 AB91-00550A ASSY-FUNCTION;SCM-21MK,FUNCTION 11 AB39-30601E LEAD-CONNECTOR ASS'Y;YFH800-03,DIA-3 12 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 13 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1

Exploded Views and Parts List
3-3
3-2 SMC-144/144N/144P
S.N.A.

Ò
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
˝
ˇ
∏
∏
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A. ˆ
∏
∏
∏
¨
’
∏
∏
Ø
Ø
Ô
S.N.A. : Service Not Available
S.N.A.
1 AB92-90604F ASSY-CRT;A34KQV42X,14’,ITC,MINI,AA94-50 2 AB91-00013A ASSY-MAIN 3 3001-001056 SPEAKER;3W,16ohm,89dB,250Hz 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 AB91-00014A ASSY-SUB;SMC-144,SUB,INPUT 9 6003-000282 SCREW-TAPTITE;BH,+,B,M3,L8,ZPC(BLK),SWCH 10 AB91-90602X ASSY-SUB;SMC-140,PWR S/W 11 AB39-30601Z LEAD-CONNECTOR ASS'Y;YFH800-03,3P,300 12 AB39-10601J CBF-POWER/CORD;ATT,VCTFK0.75,125V/7A,BLK 13 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1
”

Exploded Views and Parts List
3-4
3-3 SMC-142/142N/142P
S.N.A.

Ò
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
˝
ˇ
”
∏
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A. ˆ
∏
∏
∏
¨
’
∏
∏
Ø
Ø
Ô
S.N.A.
S.N.A. : Service Not Available
1 AB92-90604F ASSY-CRT;A34KQV42X,14’,ITC,MINI,AA94-50 2 AB91-00538A ASSY-MAIN 3 3001-001056 SPEAKER;3W,16ohm,89dB,250Hz 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 9 6003-000282 SCREW-TAPTITE;BH,+,B,M3,L8,ZPC(BLK),SWCH 10 AB91-90602X ASSY-SUB;SMC-140,PWR S/W 11 AB39-30601X LEAD-CONNECTOR ASS'Y;YFH800-03,3P,300 12 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 13 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1

Exploded Views and Parts List
3-5
3-4 SMC-140/140N/140P
S.N.A.

Ò
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
˝
ˇ
”
∏
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A. ˆ
∏
∏
∏
¨
S.N.A. ’
∏
∏
Ø
Ø
Ô
S.N.A.
S.N.A. : Service Not Available
1 AB92-90604F ASSY-CRT;A34KQV42X,14’,ITC,MINI,AA94-50
2 AB91-90603R ASSY-MAIN 3 3001-001056 SPEAKER;3W,16ohm,89dB,250Hz 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 9 6003-000282 SCREW-TAPTITE;BH,+,B,M3,L8,ZPC(BLK),SWCH 10 AB91-90602X ASSY-SUB;SMC-140,PWR S/W 11 AB39-30601X LEAD-CONNECTOR ASS'Y;YFH800-03,3P,300 12 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 13 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1

Exploded Views and Parts List
3-6
3-5 SMC-102/102N/102P
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
ˇ
”
∏
Ø
∏
Ø
∏
∏
∏
∏
¨
’
˝
ˆS.N.A.
S.N.A. : Service Not Available
1 AB03-10601F CRT-COLOR;A23KQU22X01,10INCH,90DEG,-,ITC 2 AB91-00537A ASSY-MAIN 3 AB92-90604S ASSY-SPEAKER;SPEAKER,AB39-30602Q,SG03A01 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 AB60-10601P SCREW-SPECIAL;BH,+,B,M2.6 18,ZPC(YEL),SW 9 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 10 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1

Exploded Views and Parts List
3-7
3-6 SMC-100/100N/100P
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
ˇ
”
∏
Ø
∏
Ø
∏
∏
∏
∏
¨
’
˝
ˆ
S.N.A. : Service Not Available
S.N.A.
1 AB03-10601F CRT-COLOR;A23KQU22X01, 10INCH,90DEG 2 AB91-90602Y ASSY-MAIN 3 AB92-90604S ASSY-SPEAKER;SPEAKER,AB39-30602Q,SG03A01 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 AB60-10601P SCREW-SPECIAL;BH,+,B,M2.6 18,ZPC(YEL),SW 9 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 10 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1

Exploded Views and Parts List
3-8
3-7 SMP-152/152N/152P
S.N.A.

Ò
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
˝
ˇ
∏
∏
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A. ˆ
∏
∏
∏
¨
S.N.A. ’
∏
∏
Ø
Ø
Ô
S.N.A. : Service Not Available
S.N.A.
1 AB03-10601C CRT-COLOR;M36KUQ35X11,15INCH,90deg,57%,I 2 AB91-00002A ASSY-MAIN 3 3001-001056 SPEAKER;3W,16ohm,89dB,250Hz 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 AB91-00015A ASSY-SUB;SMP-152,SUB,PAL-COMB FILTER 9 6003-000282 SCREW-TAPTITE;BH,+,B,M3,L8,ZPC(BLK),SWCH 10 AB91-90601W ASSY-SUB;SMP-150,PWR S/W 11 AB39-30601X LEAD-CONNECTOR ASS'Y;YFH800-03,3P,300 12 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 13 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1
”

Exploded Views and Parts List
3-9
3-8 SMP-150/150N/150P
S.N.A.

Ò
S.N.A.
S.N.A.
S.N.A.
S.N.A.
Œ
´
˝
ˇ
”
∏
S.N.A.
S.N.A.
S.N.A.
S.N.A.
S.N.A. S.N.A.
S.N.A.
S.N.A.
S.N.A. ˆ
∏
∏
∏
¨
S.N.A. ’
∏
∏
Ø
Ø
Ô
S.N.A. : Service Not Available
S.N.A.
1 AB03-10601C CRT-COLOR;M36KUQ35X11,15INCH,90deg,57%,I 2 AB91-90601Z ASSY-MAIN 3 3001-001056 SPEAKER;3W,16ohm,89dB,250Hz 4 6003-001086 SCREW-TAPTITE;BH,+,B,M3,L12,ZPC(BLK),SWR 5 AB60-10601N SCREW-ASSY;SMC-140,SWRCH18,M5X1.59X28,-, 6 AB60-10601B SCREW-ASSY TAPT;BH,+,S,M4 8,ZPC(YEL) ,SW 7 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 8 6003-001003 SCREW-TAPTITE;BH,+,B,M4,L12,ZPC(BLK),SWR 9 6003-000282 SCREW-TAPTITE;BH,+,B,M3,L8,ZPC(BLK),SWCH 10 AB91-90601W ASSY-SUB;SMP-150,PWR S/W 11 AB39-30601X LEAD-CONNECTOR ASS'Y;YFH800-03,3P,300 12 AB39-10601F CBF-POWER/CORD;DET,SJT 18AWG 3C,125V/10A 13 AB39-10601G CBF-POWER/CORD;DET,H05VV-F,250V/6A,BLK,1

Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark
4-1
2 AB91-00547A ASSY-MAIN
C102 2202-000781 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C103 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C105 2202-000781 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C106 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C107 2202-000781 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C108 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C109 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C111 2202-000781 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP
C112 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C113 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C114 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C115 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C116 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C120 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C121 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C203 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C204 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm
C205 2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5
C206 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C207 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C209 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C211 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C216 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C217 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C218 2201-000139 C-CERAMIC,DISC;100pF,2%,50V,CH,TP,8x3,5
C219 2201-000273 C-CERAMIC,DISC;18pF,5%,50V,CH,TP,5x3mm,5
C220 2301-000264 C-FILM,PEF;4.7nF,5%,50V,TP,6.5X5.5X3.0X5
C221 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C222 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C223 2401-001271 C-AL;4.7UF,20%,50V,GP,TP,4X7,5MM
C224 2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm,
C225 2301-000264 C-FILM,PEF;4.7nF,5%,50V,TP,6.5X5.5X3.0X5
C226 2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5
C227 2202-000109 C-CERAMIC,MLC-AXIAL;100NF,+80-20%,50V,Y5
C228 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C231 2202-000173 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,1
C232 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C233 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C234 2401-001495 C-AL;47uF,20%,16V,GP,5x11mm,5mm,TP
C250 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C252 2202-000173 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,1
C255 2202-000161 C-CERAMIC,MLC-AXIAL;15pF,5%,50V,NPO,TP,2
C256 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C257 2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5
C258 2305-000355 C-FILM,MPEF;330nF,5%,63V,TP,-,5mm
C259 2401-001271 C-AL;4.7UF,20%,50V,GP,TP,4X7,5MM
C260 2201-000139 C-CERAMIC,DISC;100pF,2%,50V,CH,TP,8x3,5
C261 2401-001271 C-AL;4.7UF,20%,50V,GP,TP,4X7,5MM
C262 2201-000139 C-CERAMIC,DISC;100pF,2%,50V,CH,TP,8x3,5
C263 2201-000139 C-CERAMIC,DISC;100pF,2%,50V,CH,TP,8x3,5
C264 2201-000139 C-CERAMIC,DISC;100pF,2%,50V,CH,TP,8x3,5
C265 2201-000471 C-CERAMIC,DISC;.33NF,10%,50V,Y5P,TP,4X3M
C266 2201-000375 C-CERAMIC,DISC;220pF,5%,50V,RH,TP,9.5x3.
C267 2201-000375 C-CERAMIC,DISC;220pF,5%,50V,RH,TP,9.5x3.
C301 2305-000149 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5
C302 2305-000149 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5
C303 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C304 2401-002459 C-AL;220uF,20%,25V,LZ,TP,10x16,5
C305 2401-001662 C-AL;68uF,20%,100V,GP,TP,10x16mm,5m
C401 2301-000380 C-FILM,PEF;10nF,5%,50V,TP,6.5x3mm,5mm
C402 2401-002619 C-AL;47uF,20%,25V,GP,TP,5x11,5
C403 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4
C404 2401-001662 C-AL;68uF,20%,100V,GP,TP,10x16mm,5m
C405 2201-000600 C-CERAMIC,DISC;560pF,10%,50V,Y5P,TP,5x3,
C406 2401-000927 C-AL;22UF,20%,250V,GP,TP,13X20MM,5M
C407 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4
C408 2401-001778 C-AL;470uF,20%,25V,GP,TP,10x16,5
C409 2201-000991 C-CERAMIC,DISC;560pF,10%,2KV,Y5P,TP,13x7
C410 2305-000154 C-FILM,MPEF;100nF,5%,400V,TP,21.5x6.5x11
C411 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4
C413 2306-000328 C-FILM,MPPF;6.8nF,5%,1.6KV,TP,28.5x18x10
C415 2306-000205 C-FILM,MPPF;430nF,5%,400V,BK,26x21.5x14.
C416 2401-002267 C-AL;2.2uF,20%,250V,GP,TP,8x11.5,5
C418 2201-000984 C-CERAMIC,DISC;680pF,10%,2KV,Y5P,TP,11x6
C420 2305-000382 C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mm
C501 2301-000285 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m
C503 2401-001998 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm
C504 2202-000205 C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C505 2202-000205 C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C506 2202-000205 C-CERAMIC,MLC-AXIAL;22pF,5%,50V,SL,TP,1.
C507 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4
C508 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4
C509 2201-000556 C-CERAMIC,DISC;470pF,10%,500V,Y5P,TP,7x4
C510 2401-001232 C-AL;4.7uF,20%,250V,GP,TP,10x12.5mm
C511 2401-000832 C-AL;220uF,20%,25V,GP,TP,8x11.5,5
C513 2301-000213 C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5
C514 2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm
C515 2401-000430 C-AL;10uF,20%,250V,GP,TP,10x16mm,5m
C516 2301-000213 C-FILM,PEF;220nF,5%,250V,TP,21.5x11,7.5
C517 2201-000158 C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,BK,-
C519 2401-000832 C-AL;220uF,20%,25V,GP,TP,8x11.5,5
C601 2202-000263 C-CERAMIC,MLC-AXIAL;470pF,10%,50V,Y5P,TP
C602 2202-000263 C-CERAMIC,MLC-AXIAL;470pF,10%,50V,Y5P,TP
C603 2202-000263 C-CERAMIC,MLC-AXIAL;470pF,10%,50V,Y5P,TP
C604 2401-000481 C-AL;10uF,20%,50V,WT,TP,5x11mm,5mm
C605 2401-000481 C-AL;10uF,20%,50V,WT,TP,5x11mm,5mm
C606 2401-000481 C-AL;10uF,20%,50V,WT,TP,5x11mm,5mm
C607 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C608 2301-000380 C-FILM,PEF;10nF,5%,50V,TP,6.5x3mm,5mm
C609 2301-000342 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm,
C610 2401-000481 C-AL;10uF,20%,50V,WT,TP,5x11mm,5mm
C611 2305-000149 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5
C612 2401-001778 C-AL;470uF,20%,25V,GP,TP,10x16,5
C613 2301-000380 C-FILM,PEF;10nF,5%,50V,TP,6.5x3mm,5mm
C614 2401-000151 C-AL;1000uF,20%,25V,GP,TP,12.5x20,5
C801 2306-000321 C-FILM,MPPF;470nF,5%,250V,TP,-,22.5mm
C802 2306-000321 C-FILM,MPPF;470nF,5%,250V,TP,-,22.5mm
C804 2201-000332 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,1
C805 2201-000332 C-CERAMIC,DISC;2.2nF,20%,250VAC,Y5U,TP,1
C806 2401-000052 C-AL;220uF,20%,400V,GP,BK,30x35mm,1
C807 2306-000323 C-FILM,MPPF;2.2nF,5%,1.6KV,TP,28.5x15.5x
C808 2401-002289 C-AL;470uF,20%,35V,WT,TP,10x20,5
C809 2401-000851 C-AL;220uF,20%,35V,HR,TP,13x25,5
C810 2201-000990 C-CERAMIC,DISC;4.7nF,20%,400V,Y5U,BK,7x1
C811 2401-001507 C-AL;47uF,20%,16V,GP,TP,6.3x5,5
C812 2201-000991 C-CERAMIC,DISC;560pF,10%,2KV,Y5P,TP,13x7
C813 2401-000293 C-AL;100uF,+30-10%,200V,HR,TP,16x25
C816 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4
C817 2401-002211 C-AL;1000UF,20%,35V,LZ,TP,13X25,5
4. Electrical Parts List
SMC-210/210N/210P

Loc.No Part No Description ; Specification RemarkLoc.No Part No Description ; Specification Remark
4-2
Electrical Parts List
C818 2201-000599 C-CERAMIC,DISC;560pF,10%,500V,Y5P,TP,7x4
C819 2401-002211 C-AL;1000UF,20%,35V,LZ,TP,13X25,5
C820 2305-000412 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm
C821 2401-003026 C-AL;330uF,20%,200V,GP,ST,22x35,10
C822 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C823 2401-000832 C-AL;220uF,20%,25V,GP,TP,8x11.5,5
C824 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C825 2401-000399 C-AL;10uF,20%,160V,HR,TP,10x20,5mm
C828 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C829 2401-000553 C-AL;1uF,10%,50V,GP,TP,5x11,5
C831 2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5
C834 2401-001552 C-AL;47uF,20%,35V,GP,TP,6.3x11,2.5
C901 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C903 2202-000109 C-CERAMIC,MLC-AXIAL;100NF,+80-20%,50V,Y5
C909 2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm
C910 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
C911 2202-000173 C-CERAMIC,MLC-AXIAL;1nF,10%,50V,Y5P,TP,1
C912 2201-000257 C-CERAMIC,DISC;16pF,5%,50V,CH,TP,5x3,5
C913 2201-000257 C-CERAMIC,DISC;16pF,5%,50V,CH,TP,5x3,5
C915 2306-000122 C-FILM,MPPF;100nF,5%,50V,TP,7.3x4.0x5.0m
C916 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
C917 2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5
C923 2301-000246 C-FILM,PEF;33nF,5%,100V,TP,7x5.0x9.5mm,5
C924 2301-000264 C-FILM,PEF;4.7nF,5%,50V,TP,6.5X5.5X3.0X5
C925 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5
CN04A 3711-002646 CONNECTOR-HEADER;BOX,7P,1R,2.5mm,STRAIGH
CN07A AB39-30601F LEAD-CONNECTOR,ASS’Y:YBNH-250-07,S,7P,50
CN08A AB39-30601J LEAD-CONNECTOR,ASS’Y:YBNH-250-05,S,5P,50
CN09A 3711-002644 CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGH
CN601 3711-002642 CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGH
CZ901 2201-000257 C-CERAMIC,DISC;16pF,5%,50V,CH,TP,5x3,5
CZ902 2201-000257 C-CERAMIC,DISC;16pF,5%,50V,CH,TP,5x3,5
D201 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D202 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D203 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D205 0402-000129 DIODE-RECTIFIER;1N4003,200V,1A,DO-41,TP
D207 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D208 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D209 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D401 0402-000129 DIODE-RECTIFIER;1N4003,200V,1A,DO-41,TP
D402 0402-000129 DIODE-RECTIFIER;1N4003,200V,1A,DO-41,TP
D403 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-
D404 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-
D405 0402-000010 DIODE-RECTIFIER;RGP15G,400V,1.5A,DO-204A
D407 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D408 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41
D501 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D503 0402-000129 DIODE-RECTIFIER;1N4003,200V,1A,DO-41,TP
D504 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D801 0402-000116 DIODE-BRIDGE;RBV606,600V,6A,-,ST
D802 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L
D803 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41
D804 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41
D805 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41
D806 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-
D808 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-
D809 0402-000564 DIODE-RECTIFIER;FML-G22S,200V,10A,TO-220
D810 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41
D811 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D812 0402-000213 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41
D815 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41
D901 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D903 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D904 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
D905 0401-000005 DIODE-SWITCHING;1N4148,75V,300mA,DO-35,T
DZ101 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DZ102 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DZ103 0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DZ104 0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m
DZ201 0403-000667 DIODE-ZENER;MTZ6.8A,6.8V,6.29-6.63V,500m
DZ401 0403-000668 DIODE-ZENER;MTZ8.2B,8.2V,7.78-8.19V,500m
DZ501 0403-000655 DIODE-ZENER;MTZ13A,13V,12.11-12.75V,500m
DZ601 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DZ602 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DZ603 0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m
DZ801 1405-000152 VARISTOR;560V,2500A,14x8.5mm,TP
DZ803 0403-000355 DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500
DZ804 0403-000704 DIODE-ZENER;TZP7.5B,7.5V,7.5-8.4V,1W,DO-
DZ805 0403-000656 DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m
DZ806 0403-000355 DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500
DZ901 0403-000355 DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500
DZ902 0403-000297 DIODE-ZENER;MTZ6.2B,6.2V,5.96-6.27V,500m
F801 3601-000279 FUSE-FERRULE;250V,4A,SLOW BLOW,GLASS,5x2
HIC501 AB13-20601A IC-HYBRID:SPK101T,SIP,6P,M-MONITOR
IC101 1001-000205 IC-ANALOG SWITCH;TC4053BP,CMOS 2-CHANNEL
IC102 AB29-90601A FILTER-COM:CFM102,NTSC,3.58MHz,ST
IC201 1204-000467 IC-CHROMA;TDA8374A,DIP,56P,-,PLASTIC,8V,
IC202 1209-000214 IC-DELAY LINE;TDA4665,DIP,16P,300MIL,PLA
IC203 1201-001253 IC-VIDEO AMP;14576,DIP,8P,250MIL,DUAL,-,
IC204 1204-000636 IC-PICTURE PROCESS;TDA4566,DIP,18P,300MI
IC301 1204-000441 IC-IF CIRCUIT;TDA8356,SIP,9P,-,PLASTIC,4
IC501 1201-000539 IC-VIDEO AMP;6101,ZIP,9P,-,SINGLE,-,PLAS
IC502 1201-000539 IC-VIDEO AMP;6101,ZIP,9P,-,SINGLE,-,PLAS
IC503 1201-000539 IC-VIDEO AMP;6101,ZIP,9P,-,SINGLE,-,PLAS
IC601 1001-000211 IC-VIDEO SWITCH;NJM2235D,-,DIP,8P,300MIL
IC602 1201-001360 IC-AUDIO AMP;1013,SIP,9P,-,SINGLE,-,PLAS
IC801 AB13-20601C IC-HYBRID:STR6707,SIP,9P,SMPS CONTROL
IC802 1203-000575 IC-POSI.ADJUST.REG;8133,SIP,9P,-,PLASTIC
IC803 AB13-20601D IC-HYBRID:SE125N,SIP,3P,ERROM AMP
IC901 AB09-00001A IC-MICOM;KS88P8324,SDIP,42PINS,COLOR TV
IC902 1103-000156 IC-EEPROM;24C04,512X8BIT,DIP,8P,300MIL,1
JA601 3722-000200 JACK-RCA;6P,3.4mm,SN,BLACK,-
JA101 3705-001076 CONNECTOR-COAXIAL:BNC,JACK,20mohm,-,-
JA102 3705-001077 CONNECTOR-COAXIAL:BNC,JACK,20mohm,-,0.1N
JA103 3705-001076 CONNECTOR-COAXIAL:BNC,JACK,20mohm,-,-
JA104 3705-001077 CONNECTOR-COAXIAL:BNC,JACK,20mohm,-,0.1N
JA105 3722-001163 JACK-VHS;11P,12mm,AU,BLK,N
JA106 3722-001163 JACK-VHS;11P,12mm,AU,BLK,N
L201 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L202 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L203 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L204 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L207 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L208 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L209 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L301 2701-000116 INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
L302 2701-000116 INDUCTOR-AXIAL;10uH,10%,4.2x9.8mm
L402 AB27-30601E COIL-LINEARITY;195uH,-,-,-,-
L403 AB27-10601A COIL-CHOKE:100uH,K,Q10,700mA,T,-,-,-,-
L404 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L405 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L406 AB27-10601B COIL-CHOKE:6.8mH,K,50,150mA,ST,-,-,-,-
L601 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L602 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L603 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L801 AB29-30601J FILTER-LINE;27mH MIN,1A,AC250V,-
L802 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L803 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L804 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L805 AB29-30601K FILTER-LINE;38mH MIN,1A,AC250V,-
L806 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-
L808 AB27-10601A COIL-CHOKE:100uH,K,Q10,700mA,T,-,-,-,-

Loc.No Part No Description ; Specification Remark Loc.No Part No Description ; Specification Remark
Electrical Parts List
4-3
L809 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L810 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L811 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L812 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L813 3301-000287 CORE-FERRITE BEAD;AA,3.5x1x6mm,1500,2400
L901 2702-000181 INDUCTOR-RADIAL;680uH,5%,6x6.4mm
L902 2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-
L903 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L904 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L905 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
L906 2701-000114 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
LS01 2701-000301 INDUCTOR-AXIAL;24uH,10%,2.5x3.4mm
NT801 1404-000181 THERMISTOR-NTC;4.7ohm,20%,2900K,-,BK
P801 1404-000180 THERMISTOR-PTC;14ohm,20%,-,290V,25A,-,ST
PC801 0604-000117 PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST
Q105 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
Q106 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
Q203 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
Q205 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T
Q206 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T
Q401 0502-000295 TR-POWER;KSD5072YD,NPN,1500V,800V,5A,60
Q402 0501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,
Q601 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T
Q602 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
Q805 0503-000128 TR-DARLINGTON;TIP102,NPN,2W,TO-220,BK,10
Q908 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
Q909 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T
R107 2001-001187 R-CARBON(S);75OHM,5%,1/2W,AA,TP,2.4X6.4M
R113 2001-001187 R-CARBON(S);75OHM,5%,1/2W,AA,TP,2.4X6.4M
R115 2001-001187 R-CARBON(S);75OHM,5%,1/2W,AA,TP,2.4X6.4M
R116 2001-001187 R-CARBON(S);75OHM,5%,1/2W,AA,TP,2.4X6.4M
R118 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R119 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R120 2004-001027 R-METAL;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2m
R121 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R122 2004-001027 R-METAL;5.6Kohm,5%,1/8W,AA,TP,1.8x3.2m
R123 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R124 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R125 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R203 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R204 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R206 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R207 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM
R208 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM
R209 2001-000003 R-CARBON;330OHM,5%,1/8W,AA,TP,1.8X3.2MM
R210 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R211 2001-000548 R-CARBON;270KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R212 2001-000273 R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R214 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R215 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R216 2001-000832 R-CARBON;510OHM,5%,1/8W,AA,TP,1.8X3.2MM
R217 2001-001408 R-CARBON(S);3.3MOHM,5%,1/2W,AA,TP,2.4X6.
R218 2004-001914 R-METAL;39Kohm,2%,1/8W,AA,TP,1.8x3.5mm
R219 2001-000016 R-CARBON(S);1OHM,5%,1/2W,AA,TP,2.4X6.4MM
R224 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R225 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R227 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R234 2001-000009 R-CARBON;20KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R235 2001-000633 R-CARBON;30KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R241 2001-000508 R-CARBON;220KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R242 2004-001351 R-METAL;91Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R243 2001-000766 R-CARBON;43KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R244 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R245 2004-001990 R-METAL;62Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R246 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R247 2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R251 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R252 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R253 2001-001365 R-CARBON;15KOHM,1%,1/8W,AA,TP,1.8X3.2MM
R254 2001-000857 R-CARBON;560OHM,5%,1/8W,AA,TP,1.8X3.2MM
R255 2001-000674 R-CARBON;360OHM,5%,1/8W,AA,TP,1.8X3.2MM
R256 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R257 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R258 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R259 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R260 2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R301 2004-001983 R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.
R302 2003-001032 R-METAL OXIDE(S);220ohm,5%,1W,AF,TP,2.5x
R303 2001-000037 R-CARBON(S);330OHM,5%,1/2W,AA,TP,2.4X6.4
R304 2001-000016 R-CARBON(S);1OHM,5%,1/2W,AA,TP,2.4X6.4MM
R401 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
R402 2001-000591 R-CARBON;3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R403 2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4
R404 2003-000713 R-METAL OXIDE(S);47ohm,5%,2W,AF,TP,4x12m
R405 2001-003019 R-CARBON(S);0.39OHM,10%,1/2W,AA,TP,2.4X6
R406 2008-000262 R-FUSIBLE(S);150ohm,5%,2W,AF,TP,3.9x10mm
R407 2001-000022 R-CARBON(S);33OHM,5%,1/2W,AA,TP,2.4X6.4M
R409 2008-000206 R-FUSIBLE(S);1ohm,5%,1/2W,AF,TP,2.5x6.5m
R410 2008-000277 R-FUSIBLE;68ohm,5%,1/2W,AA,TP,4.7x11mm
R411 2008-000264 R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm
R412 2008-000204 R-FUSIBLE(S);0.22ohm,10%,1/2W,AF,TP,2.5x
R413 2003-000746 R-METAL OXIDE(S);56ohm,5%,2W,AF,TP,4x12m
R414 2004-001408 R-METAL(S);91Kohm,1%,1/2W,AA,TP,2.4x6.4m
R415 2003-000993 R-METAL OXIDE(S);3.9Kohm,5%,1W,AF,TP,2.5
R416 2003-000540 R-METAL OXIDE(S);1Kohm,5%,2W,AF,TP,4x12m
R417 2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm
R418 2003-000746 R-METAL OXIDE(S);56ohm,5%,2W,AF,TP,4x12m
R419 2004-001234 R-METAL;75Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R420 2001-000563 R-CARBON;27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R421 2004-001408 R-METAL(S);91Kohm,1%,1/2W,AA,TP,2.4x6.4m
R422 2001-000085 R-CARBON(S);100KOHM,5%,1/2W,AA,TP,2.4X6.
R423 2008-000264 R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm
R424 2003-000540 R-METAL OXIDE(S);1Kohm,5%,2W,AF,TP,4x12m
R425 2001-001410 R-CARBON(S);43OHM,5%,1/2W,AA,TP,2.4X6.4M
R426 2008-000264 R-FUSIBLE(S);1ohm,5%,1W,AF,TP,3.9x10mm
R501 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R502 2004-001402 R-METAL(S);6.8Kohm,1%,1/2W,AA,TP,2.4x6.4
R503 2004-001394 R-METAL(S);2Kohm,1%,1/2W,AA,TP,2.4x6.4mm
R504 2001-000522 R-CARBON;22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R505 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R506 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R507 2001-000449 R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R508 2004-001970 R-METAL;1.8Kohm,1%,1/2W,AA,TP,6.5x2.5m
R509 2004-001970 R-METAL;1.8Kohm,1%,1/2W,AA,TP,6.5x2.5m
R510 2004-001970 R-METAL;1.8Kohm,1%,1/2W,AA,TP,6.5x2.5m
R511 2004-001373 R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4
R512 2004-001373 R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4
R513 2004-001373 R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4
R514 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R515 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R516 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM
R517 2002-000327 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.5
R518 2002-000327 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.5
R519 2002-000327 R-COMPOSITION;2.7Kohm,10%,1/2W,AA,TP,3.5
R520 2001-000096 R-CARBON(S);1MOHM,5%,1/2W,AA,TP,2.4X6.4M
R522 2001-001107 R-CARBON(S);220ohm,5%,1/2W,AA,TP,2.4x6.4
R523 2001-000028 R-CARBON(S);100OHM,5%,1/2W,AA,TP,2.4X6.4
R601 2001-001152 R-CARBON(S);47KOHM,5%,1/2W,AA,TP,2.4X6.4
R602 2001-001152 R-CARBON(S);47KOHM,5%,1/2W,AA,TP,2.4X6.4
R603 2001-001152 R-CARBON(S);47KOHM,5%,1/2W,AA,TP,2.4X6.4
R604 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R605 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM