Samsung QB43R User manual

SERVICE Manual
LFD Monitor
Refer to the service manual in the GSPN (see the rear cover) for the more information.
Contents
LFD Monitor
Chassis Model
FT90 QB43R / QB49R / QB55R /
QB65R / QB75R / QB98R
FS90 QM43R / QM49R / QM55R /
QM65R / QM75R
1. Precautions
2. Product specifications
3. Disassembly and Reassembly
4. Troubleshooting
5. Wiring Diagram

Contents
1. Precautions
1-1. Safety Precautions.........................................................................................................................1-1
1-1-1. Servicing the Product.........................................................................................................1-1
1-1-2. Fire and Shock Hazard ......................................................................................................1-1
1-1-3. Product Safety Notices.......................................................................................................1-2
1-2. Servicing Precautions ....................................................................................................................1-3
1-2-1. General Servicing Precautions...........................................................................................1-3
1-3. Static Electricity Precautions..........................................................................................................1-4
1-4. Installation Precautions..................................................................................................................1-5
2. Product specifications
2-1. Model Comparison.........................................................................................................................2-1
2-2. Feature & Specifications ................................................................................................................2-2
2-3. Detail Factory Option .....................................................................................................................2-8
2-4. Accessories....................................................................................................................................2-10
2-5. What Is Different About the Product...............................................................................................2-12
2-5-1. Remote Control (of up to 100 devices) through the Built-in RJ45 and RS-232C Ports......2-12
2-5-2. Optimum Picture Quality and Afterimage Burn-in Prevention ............................................2-13
2-5-3. HDCP Operation ................................................................................................................2-15
3. Disassembly and Reassemble
3-1. Product Disassembly [43" ~ 75"]....................................................................................................3-1
3-2. Product Disassembly [98"] .............................................................................................................3-6
4. Troubleshooting
4-1. Previous check...............................................................................................................................4-1
4-2. How to check fault symptom ..........................................................................................................4-6
4-2-1. When the product is not powered on (43"~75") .................................................................4-6
4-2-2. When the product is not powered on (98").........................................................................4-8
4-2-3. When a blank screen is displayed (HDMI-Digital signal) ...................................................4-10
4-2-4. When a blank screen is displayed (HDMI-Digital signal) (98")...........................................4-12
4-2-5. When no sound is output (Speaker) (43"~75") ..................................................................4-14
4-2-6. When no sound is output (Speaker) (98")..........................................................................4-16
4-3. Troubleshooting Guide...................................................................................................................4-18
4-3-1. Requirements Before Contacting Samsung Customer Service Center .............................4-18
4-4. Error Examples and Actions...........................................................................................................4-24
4-5. Factory Mode Adjustments ............................................................................................................4-25
4-5-1. Entering the Service Mode.................................................................................................4-25
4-5-2. Factory Data.......................................................................................................................4-26
4-5-3. EDID settings .....................................................................................................................4-53

4-6. Cable..............................................................................................................................................4-54
4-6-1. RS-232C cable...................................................................................................................4-54
4-6-2. LAN cable...........................................................................................................................4-56
4-7. White Balance................................................................................................................................4-58
4-7-1. Calibration..........................................................................................................................4-58
4-7-2. White Balance Adjustment .................................................................................................4-60
4-8. Software Upgrade ..........................................................................................................................4-61
4-8-1. How to check the Software Version ...................................................................................4-61
4-8-2. How to upgrade Software...................................................................................................4-63
4-9. How to get the debug logs - Serial debug......................................................................................4-67
4-9-1. USB Log saving Function guide.........................................................................................4-70
4-10. Service Item Code .........................................................................................................................4-73
5. Wiring Diagram
5-1. Wiring Diagram ..............................................................................................................................5-1
5-2. Block Diagram................................................................................................................................5-2
5-3. Board Connection ..........................................................................................................................5-3
5-4. Connector Functions......................................................................................................................5-15
5-5. Cables............................................................................................................................................5-16

GSPN (GLOBAL SERVICE PARTNER NETWORK)
Area Web Site
Europe, MENA, CIS,
Africa https://gspn1.samsungcsportal.com
E.Asia, W.Asia,
China, Japan https://gspn2.samsungcsportal.com
N.America, S.America https://gspn3.samsungcsportal.com
This Service Manual is a property of Samsung Electronics
Co.,Ltd.
Any unauthorized use of Manual can be punished under
applicable International and/or domestic law.
© 2019 Samsung Electronics Co.,Ltd.
All rights reserved.
Printed in Korea

1. Precautions
1-1. Safety Precautions
• Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
Warning
• For continued safety, do not attempt to modify the circuit board.
• Disconnect the AC power and DC power jack before servicing.
1-1-1. Servicing the Product
1. When servicing the Product, Disconnect the AC line cord from the AC outlet.
2. It is essential that service technicians have an accurate voltage meter available at all times. Check the calibration of this
meter periodically.
1-1-2. Fire and Shock Hazard
• Before returning the product to the user, perform the following safety checks:
1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis
and other metal parts in the product.
2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and
compartment covers or shields, isolation resistorcapacitor networks, mechanical insulators, etc.
3. Leakage Current Hot Check:
Warning
• Do not use an isolation transformer during
this test.
• Use a leakage current tester or a metering
system that complies with American
National Standards Institute (ANSI C101.1,
Leakage Current for Appliances), and
Underwriters Laboratories (UL Publication
UL1410, 59.7).
4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit’s AC switch first in
the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets, screwheads and control shafts.
The current measured should not exceed 0.5 milliamp.
Reverse the power-plug prongs in the AC outlet and repeat the test.
1-1
Precautions
DEVICE
UNDER
TEST
(READING SHOULD)
NOT BE ABOVE 0.5mA
LEAKAGE
CURRENT
TESTER
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND

1-1-3. Product Safety Notices
• Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual
inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage,
wattage, etc. Parts that have special safety characteristics are identified by on schematics and parts lists.
A substitute replacement that does not have the same safety characteristics as the recommended replacement part might
create shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued
whenever appropriate.
1-2
Precautions

1-2. Servicing Precautions
Warning
• An electrolytic capacitor installed with the wrong polarity might explode.
Caution
• Before servicing units covered by this service manual, read and follow the Safety Precautions section of
this manual.
Note
• If unforeseen circumstances create conflict between the following servicing precautions and any of the
safety precautions, always follow the safety precautions.
[For QM98N]
CAUTION
DOUBLE POLE/NEUTRAL FUSING
1-2-1. General Servicing Precautions
1. Always unplug the unit’s AC power cord from the AC power source and disconnect the DC Power Jack before attempting to:
(a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test component
in parallel with an electrolytic capacitor.
2. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used.
The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to
their original position.
3. After servicing, always check that the screws, components and wiring have been correctly reinstalled.
Make sure that the area around the serviced part has not been damaged.
4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input
terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON.
Connect an insulation resistance meter (500V) to theblades of the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater
than 1 megohm.
6. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead;
always remove the instrument’s ground lead last.
1-3
Precautions

1-3. Static Electricity Precautions
• Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect
transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body
by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to the product.
2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation
of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.
4. Use only a grounded-tip soldering iron to solder or desolder ESDs.
5. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate
electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective package until you are ready to install it.
Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or
other conductive materials.
7. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to
the chassis or circuit assembly into which the device will be installed.
Caution
• Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting
your foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
Precautions

1-4. Installation Precautions
1. For safety reasons, more than a people are required for carrying the product.
2. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock.
3. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature
may cause fire.
4. Bend the external antenna cable when connecting it to the product. This is a measure to protect it from being exposed to
moisture. Otherwise, it may cause a fire or electric shock.
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product.
Also check the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or
electric shock.
6. Keep the antenna far away from any high-voltage cables and install it firmly. Contact with the highvoltage cable or the
antenna falling over may cause fire or electric shock.
7. When installing the product, leave enough space (0.4 m) between the product and the wall for ventilation purposes.
A rise in temperature within the product may cause fire.
8. If an equipment is provided with a replaceable battery, and if replacement by an incorrect type could result in an explosion
(for example, with some lithium batteries), the following applies:
Caution
• Risk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the
instructions.
• Do not dispose of batteries in a fire.
• Do not short circuit, disassemble or overheat the batteries.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Do not be exposed to excessive heat such as sunshine, fire or the like.
1-5
Precautions

2-1
Product specifications
2. Product specifications
2-1. Model Comparison
Front View
W
D
* W : Width H : Height D : Depth
H
Front Color Black
Dimensions
(W x H x D)
(Non-NETWORK)
/
Weight
(Non-NETWORK)
43"
Set 967.5 x 557.7 x 48.3mm / 10.0Kg
Package 1095 x 676 x 151mm / 13.3Kg
49"
Set 1099.2 x 631.5 x 46.3mm / 13.5Kg
Package 1247 x 772 x 152mm / 18.0Kg
55"
Set 1235.1 x 707.9 x 46.3mm / 18.1Kg
Package 1402 x 858 x 163mm / 23.6Kg
65"
Set 1453.9 x 831.0 x 46.3mm / 24.9kg
Package 1611 x 973 x 185mm / 33.3kg
75"
Set 1681.1 x 960.1 x 49.7mm / 38.3kg
Package 1871 x 1127 x 223mm / 49.0kg
98
Set 2194.2 x 1249.8 x 75.3mm / 77.1 Kg
Package 2500 x 1618 x 815mm / 149.4 Kg
Panel Type LCM / LED
Feature
QMR / QB98R HDMI IN 1, HDMI IN 2, HDMI OUT, DP IN
QBR HDMI IN 1, HDMI IN 2

2-2
Product specifications
2-2. Feature & Specifications
Model Name QM43R / QM49R / QM55R /QM65R / QM75R
Feature
• 24/7 , IT Standard, Pivot mode support, EMI Class A
• 500nit, Edge Type, Non-glare Panel
• Tizen Platform with Enhanced Security
• Kant-M2e platform
• Tizen 4.0
• Connectivity : HDMI2.0(In x2, Out x1), DVI-D(1), DP1.2(1),
USB(2), RJ45, RS232C(In/Out), Audio(In/Out)
• WiFi
• IP5x
• W/M : WMN4070SE (43”~55”) WMN6575SE(65”~75”)
Model Name QB43R / QB49R / QB55R /QB65R / QB75R
Feature
• 16/7 , IT Standard, Pivot mode support, EMI Class B
• 350nit, Edge Type, Glare Panel
• Tizen Platform with Enhanced Security
• Kant-M2e platform
• Tizen 4.0
• Connectivity : HDMI2.0(In x2), DVI-D(1), USB(2), RJ45,
RS232C(In/Out), Audio(In/Out)
• WiFi
• IP5x
• W/M : WMN4070SE (43”~55”) WMN6575SE(65”~75”)
Model Name QB98R
Feature
• 24/7 , IT Standard, Pivot mode support
• 350nit, Non-glare Panel
• Kant-M2e platform
• Tizen 4.0
• Connectivity : HDMI2.0(In x2, Out x1), DVI-D(1), DP1.2(1),
USB(2), RJ45, RS232C(In/Out), Audio(In/Out), IR IN
• WiFi
• W/M : WMN9500SD

2-3
Product specifications
QMR
Specifications
Item QM43R QM49R QM55R QM65R QM75R
Introduction Area Worldwide
Panel
Panel CY-
NR043HGAVYH
CY-
NR049HGLVYH
CY-
NR055HGLVYH
CY-
NR065HGLVYH
CY-
NR075HGAVYH
Vendor AUO SDC SDC SDC AUO
Optimum
resolution 3840 x 2160 @60Hz 3840 x 2160 @60Hz 3840 x 2160 @60Hz 3840 x 2160 @60Hz 3840 x 2160 @60Hz
Display area(mm)
941.184(H) x 529.416(V) 1073.78(H) x 604.00(V) 1209.6(H) x 680.4(V) 1428.48(H) x 803.52(V) 1650.24(H) x 928.26(V)
Pixel Pitch(mm) 0.2451(H) x 0.2451(V) 0.093(H) x 0.279(V) 0.105(H) X 0.315(W) 0.124(H) x 0.372 (W) 0.42975(H) x 0.42975 (W)
Display rate 16:9
Contrast rate 4000:1 4000:1 4000:1 4700:1 6000:1
Luminance(cd/
m2 ) 500
Response time (ms) 8
View angle (H/V) 178/178
Glare Panel Non-glare
(Haze=44%)
Non-glare
(Haze=25%)
Non-glare
(Haze=25%)
Non-glare
(Haze=25%)
Non-glare
(Haze=44%)
Mecha
Design Signage New Design
Depth 48.3mm 46.3mm 46.3mm 46.3mm 49.7mm
C/Rear Signage New Design
Stand STN-L4355F STN-L4355F STN-L4355F - -
Wall Mount WMN4070SE WMN4070SE WMN4070SE WMN4277SE WMN6575SE
Produce
Measurement
Vesa (mm*mm) 200mm * 200mm 200mm * 200mm 200mm * 200mm 400mm * 400mm 400mm * 400mm
Vesa screw
standard
M8, L45
+HOLDER-WALL RING
4EA
M8, L45
+HOLDER-WALL RING
4EA
M8, L45
+HOLDER-WALL RING
4EA
M8, L71
+HOLDER WALL
+HOLDER-WALL RING
4EA
M8, L71
+HOLDER WALL
+HOLDER-WALL RING
4EA
Elec
Platform Kant-M2e
PC/Video signal input DVI-D, HDMI(2), DP(1)
PC/Video signal output
HDMI(1)
Daisy chain Support(HDMI IN 2, DP IN)
Daisy chain spec. HDCP2.2(4ea) HDCP 1.4(7ea) Without HDCP(9ea)
HDMI Ver. 2
USB Support
Speaker Support
Media player Support
Network Support (SBB)
TCO standard NONE
About TV TV(Tuner) Not Support
PIP/PBP support Not Support
Resolution DVI 1920x1080
HDMI/DP 3840x2160

2-4
Product specifications
Specifications
Item QM43R QM49R QM55R QM65R QM75R
Power
Consumption
Voltage AC 100 to 240(60Hz/50Hz)
Max Power
Consumption 121 132 143 176 220
Typical power
Consumption 76 91 96 125 159
Rating power
Consumption 110 120 130 160 200
DPMS ≤ 0.5W (DVI, HDMI mode )
Exterior color
Stand
high glossy Not Support
Bezel
high glossy Not Support
Product
Exterior color Black
Pivot Support
Tilt/Swivel Not Support
Video Wall NONE
Special
• 500 nit, 24 / 7
• Remote Control by using RJ45 / RS-232C
QBR
Specifications
Item QB43R QB49R QB55R QB65R QB75R
Introduction Area Worldwide
Panel
Panel
CY-
NR043HGAVZH
CY-
NR049HGLVZH
CY-
NR055HGLVZH
CY-
NR065HGLVZH
CY-
NR075HGLVZH
Vendor AUO SDC SDC SDC SDC
Optimum
resolution
3840 x 2160 @60Hz 3840 x 2160 @60Hz 3840 x 2160 @60Hz 3840 x 2160 @60Hz 3840 x 2160 @60Hz
Display
area(mm)
941.184(H) x 529.416(V) 1073.78(H) x 604.00(V) 1209.6(H) x 680.4(V) 1428.48(H) x 803.52(V) 1650.24(H) x 928.26(V)
Pixel Pitch(mm) 0.2451(H) x 0.2451(V) 0.093(H) x 0.279(V) 0.105(H) X 0.315(W) 0.124(H) x 0.372 (W) 0.42975(H) x 0.42975 (W)
Display rate 16:9
Contrast rate 5000:1 4700:1 4700:1 4000:1 4000:1
Luminance(cd/m2)
350
Response time (ms) 8
View angle (H/V) 178/178
Glare Panel Glare (Haze=2%)
Mecha
Design Signage New Design
Depth 48.3mm 46.3mm 46.3mm 46.3mm 49.7mm
C/Rear Signage New Design
Stand STN-L4355F STN-L4355F STN-L4355F - -
Wall Mount WMN4070SE WMN4070SE WMN4070SE WMN4277SE WMN6575SE

2-5
Product specifications
Specifications
Item QB43R QB49R QB55R QB65R QB75R
Produce
Measurement
Vesa (mm*mm) 200mm * 200mm 200mm * 200mm 200mm * 200mm 400mm * 400mm 400mm * 400mm
Vesa screw
standard
M8, L45
+HOLDER-WALL RING
4EA
M8, L45
+HOLDER-WALL RING
4EA
M8, L45
+HOLDER-WALL RING
4EA
M8, L71
+HOLDER WALL
+HOLDER-WALL RING
4EA
M8, L71
+HOLDER WALL
+HOLDER-WALL RING
4EA
Elec
Platform Kant-M2e
PC/Video
signal input DVI-D, HDMI(2)
PC/Video
signal output Not Support
Daisy chain Not Support
Daisy chain
spec. Not Support
HDMI Ver. 2
USB Support
Speaker Support
Media player Support
Network Support (SBB)
TCO standard NONE
About TV
TV(Tuner) Not Support
PIP/PBP
support Not Support
Resolution DVI 1920x1080
HDMI/DP 3840x2160
Power
Consumption
Voltage AC 100 to 240
(60Hz/50Hz)
Max Power
Consumption 121 132 143 176 220
Typical power
Consumption 76 91 96 125 159
Rating power
Consumption 110 120 130 160 200
DPMS ≤ 0.5W(DVI, HDMI mode )
Exterior
color
Stand
high glossy Not Support
Bezelhigh
glossy Not Support
Product
Exterior color Black
Pivot Support
Tilt/Swivel Not Support
Video Wall NONE
Special
• 50 nit, 16 / 7
• Remote Control by using RJ45 / RS-232C

2-6
Product specifications
QB98R
Specifications
Item QB98R
Introduction Area Worldwide
Panel
Panel LTI980FN01-A
Vendor SDC
Optimum resolution 3840 x 2160 @60Hz
Display area(mm) 2158.848(H) x 1214.352(V)
Pixel Pitch(mm) 0.187 x 0.562
Display rate 16:09
Contrast rate 4000:01:00
Luminance(cd/m2) 350 nit
Response time (ms) 6
View angle (H/V) 178/178
Glare Panel Non-glare(Haze=25%)
Mecha
Design Common with QM98F
Depth 71.6(w/o handle)
75.3(with handle)
C/Rear Common with QM98F
Stand -
Wall Mount WMN9500SD
Produce
Measurement
Vesa (mm*mm) 900mm * 600mm
Vesa screw standard M8, 4EA

2-7
Product specifications
Elec
Platform Kant-M2e
PC/Video signal input DVI-D, HDMI(2), DP(1)
PC/Video signal output HDMI(1)
Daisy chain Support(HDMI IN 2, DP IN)
Daisy chain spec.
HDCP2.2(4ea)
HDCP 1.4(7ea)
Without HDCP(9ea)
HDMI Ver. 2
USB Support
Speaker Support
Media player Support
Network Support (SBB)
TCO standard NONE
About TV
TV(Tuner) Not Support
PIP/PBP support Not Support
Resolution DVI
HDMI/DP
1920x1080
3840x2160
Power Consumption
Voltage AC 100 to 240(60Hz/50Hz)
Max Power Consumption 528
Typical power Consumption 372
Rating power Consumption 480
DPMS ≤ 0.5W(DVI, HDMI mode )
Exterior color
Stand high glossy Not Support
Bezel high glossy Not Support
Product Exterior color Black
Pivot Support
Tilt/Swivel Not Support
Video Wall NONE
Special
• 350 nit, 24 / 7
• Remote Control by using RJ45 / RS-232C

2-8
Product specifications
2-3. Detail Factory Option
Note
• If you replace the main board with new one, please change the factory option as well.
The options you must change are “Type”.
Model Name QM43R QM49R QM55R
Panel
Vendor AUO SDC SDC
CODE BN95-05703A BN95-05704A BN95-05705A
PANEL CY-NR043HGAVYH CY-NR049HGLVYH CY-NR055HGLVYH
POWER
Vendor Dongyang SOLU M SOLU M
Code BN44-00952B BN44-00953B BN44-00953B
1 Factory reset
2 Type 43L6AUZNR 49A6AUZNR 55A6AUZNR
3 Local set US, KOR, CHI_DTV, TAIWAN, EU, CIS_RUSSIA, …
4 SW Model LFD QMRN
5MagicInfo Support -
6WatchDog -
Model Name QM65R QM75R
Panel
Vendor SDC AUO
CODE BN95-05706A BN95-05707A
PANEL CY-NR065HGLVYH CY-NR075HGAVYH
POWER
Vendor HANSOE HANSOE
Code BN44-00954B BN44-01005A
1 Factory reset
2 Type 65A6AUZNR 75L6AUZNR
3 Local set EU, US, KOR, TAIWAN…Etc
4 Tuner X
5 MagicInfo Support Enabled
6 WatchDog Enabled

2-9
Product specifications
Model Name QB43R QB49R QB55R
Panel
Vendor AUO SDC SDC
CODE BN95-05708A BN95-05709A BN95-05710A
PANEL CY-NR043HGAVZH CY-NR049HGLVZH CY-NR055HGLVZH
POWER
Vendor Dongyang SOLU M SOLU M
Code BN44-00952B BN44-00953B BN44-00953B
1 Factory reset
2 Type 43L6AUYNR 49A6AUYNR 55A6AUYNR
3 Local set US, KOR, CHI_DTV, TAIWAN, EU, CIS_RUSSIA, …
4 SW Model LFD QBRN
5MagicInfo Support -
6WatchDog -
Model Name QB65R QB75R QB98R
Panel
Vendor SDC SDC SDC
CODE BN95-05711A BN95-05712A BN07-01557B
PANEL CY-NR065HGLVZH CY-NR075HGLVZH LTI980FN01-A
POWER
Vendor HANSOE HANSOE SOLU M
Code BN44-00954B BN44-01005A BN44-000318C
1 Factory reset
2 Type 65A6AUYNR 75A6AUYNR 98A6AUZER
3 Local set EU, US, KOR, TAIWAN…Etc…
4 Tuner X
5MagicInfo Support Enabled
6WatchDog Enabled

2-10
Product specifications
2-4. Accessories
Product Description Code. No Remark
Batteries
4301-000121(W/W)
4301-001113(TAWAN)
4301-000103(INDIA)
Samsung
Electronics Service
Center
(The part code for
some accessories
may differ
depending on your
region.)
RS232C (IN) adapter BN39-01545B
Remote Control WW - BN59-01180A
UAE - BN59-01180C
Holder-Ring BN96-43169A
(Q*49R, Q*55R, Q*65R, Q*75R)
Holder-Cable BN96-40152A
(Q*65R, Q*75R, Q*98R)
Regulatory guide
Quick Setup Guide
Power cord Next Page

2-11
Product specifications
Power cord
43" / 49" / 55 / 65“ 75“ 98”
(2pin/1500mm/Black) (2pin/3000mm/Black) (3pin/3000mm/Black)
America 3903-001117 3903-001132 3903-001116
Europe 3903-001118 3903-001130 3903-001114
United Kingdom 3903-001119 3903-001129 3903-001115
South Korea 3903-001074 3903-001131 3903-001114
Australia 3903-001082 3903-001123 3903-001103
Argentine 3903-001079 3903-001126 3903-001095
Brazil 3903-001081 3903-001124 3903-001101
South Africa 3903-001078 3903-001139 3903-001100
India 3903-001080 3903-001125 3903-001102
Taiwan 3903-001077 3903-001138 3903-001097
Thailand 3903-001076 3903-001127 3903-001104
China 3903-001075 3903-001128 3903-001105
Chile 3903-001118 3903-001130 3903-001098
Israel 3903-001118 3903-001130 3903-001099