Samsung PS-42P2SB User manual

Plasma Display
with Media Station
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ENG
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
ELECT

2
ENG
Safety Instructions
◆Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall.
◆Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions.
◆Do not expose the PDP to direct sunlight and other sources of heat.
◆Do not expose the PDP to any liquids.
◆Never put objects of any kind into the television, and do not place a water-containing vessel on the
PDP.
◆During a storm conditions (especially when there is lightning) unplug the PDP from the mains
socket and aerial.
◆Do not step on or twist the power cord.
◆Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
◆Please use a soft and dry cloth (not containing volatile matter) when you clean the PDP.
◆If the PDP is broken, do not try to repair it yourself. Contact qualified service personnel.
◆If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
◆Do not drop the remote control.
User Instructions
◆Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of this screen when displaying a still image.
◆Cell Defect
The plasma display panel consists of fine cells. Although the panels are produced with more than
99.9 percent active cells, there may be some cells that do not produce light or remain lit.
◆Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆Warranty
-Warranty Period: One year starting from the purchase of your PDP.
-Warranty does not cover any damage caused by image retention.
-Burn-in is not covered by the warranty.

3
ENG
Caution
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
☛The main voltage is indicated on the
rear of the PDP and the frequency is
50 or 60Hz.
WARNING: TO PREVENT DAMAGE WHICH MAY
RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
!
Checking Parts
- Owner’s Instruction
- Remote Control / 2 Batteries (AAA)
- Video Cable (DVI)
- 2 Power Cords
- 3 Ferrite Cores
- S-Video Cable

4
ENG
Contents (continued)
◆FOREWORD
■Safety Instructions............................................................................................... 2
■User Instructions................................................................................................. 2
■Caution................................................................................................................ 3
■Checking Parts.................................................................................................... 3
◆CONNECTING AND PREPARING YOUR DISPLAY
■Viewing the Plasma Display................................................................................ 6
■Viewing the Media Station................................................................................... 7
■Remote Control Buttons...................................................................................... 8
■Inserting the Batteries in the Remote Control..................................................... 9
■Installing the Display on the Wall Attachment Panel........................................... 9
■Separating the Display from the Wall Attachment Panel .................................... 12
■Connecting Speakers.......................................................................................... 13
- Connecting PDP and Speakers
- Connecting Stand and Speakers
■Connecting to an Aerial (or Cable Television Network) ...................................... 14
■Switching On and Off.......................................................................................... 15
■Becoming Familiar with the Remote Control....................................................... 16
■Setting up your Remote Control.......................................................................... 17
■Plug and Play...................................................................................................... 18
■Choosing Your Language ................................................................................... 19
◆USING YOUR DISPLAY (continued)
■Storing Channels Automatically.......................................................................... 20
■Sorting the Stored Channels............................................................................... 21
■Storing Channels Manually................................................................................. 22
■Editing the Channels........................................................................................... 24
■Fine Tuning Channel Reception.......................................................................... 25
■Changing the Picture Standard........................................................................... 26
■Adjusting the Picture Settings............................................................................. 26
■Changing the Picture Size................................................................................... 27
■Freezing the Current Picture............................................................................... 27
■Adjusting the Picture Settings (PC or DVI Mode)................................................ 28
■Setting the Picture (PC Mode) ............................................................................ 29
■Changing the Sound Standard............................................................................ 30
■Adjusting the Sound Settings.............................................................................. 30
■Adjusting the Volume Automatically.................................................................... 31
■Selecting the Sound Mode.................................................................................. 32

5
ENG
Contents
◆USING YOUR DISPLAY
■Setting the Dolby Surround................................................................................. 33
■Adjusting the Dolby Pro Logic Preferences......................................................... 35
■Adjusting the Headphone Preferences ............................................................... 36
■Hearing the Melody Sound.................................................................................. 37
■Setting the Current Time..................................................................................... 37
■Switching On and Off Automatically.................................................................... 38
■Setting the Sleep Timer....................................................................................... 39
■Viewing the Picture in Picture (PIP).................................................................... 40
■Listening to the Sound of the Sub Picture........................................................... 42
■Viewing Pictures From External Sources............................................................ 42
■Redirecting an Input to the External Output........................................................ 43
◆USING THE TELETEXT FEATURE
■Teletext Feature.................................................................................................. 44
■Displaying the Teletext Information..................................................................... 45
■Selecting Display Options................................................................................... 46
■Selecting a Teletext Page................................................................................... 47
◆CONNECTIONS AND RECOMMENDATIONS FOR USE
■Connecting to the External Devices.................................................................... 48
■Connecting to the DVD Input .............................................................................. 49
■Connecting to the S-Video Input......................................................................... 49
■Connecting to the Audio Output.......................................................................... 50
■Connecting to the DVI Input................................................................................ 50
■Connecting to the PC Input................................................................................. 51
■Preset Signals..................................................................................................... 51
■Setting up Your PC Software (Windows only)..................................................... 52
■Input Mode (PC/DVI)........................................................................................... 53
■Pin Configurations............................................................................................... 54
■Care and Maintenance........................................................................................ 55
■Troubleshooting: Before Contacting Service Personnel ..................................... 56
■Wiring the Mains Power Supply Plug (UK Only)................................................. 57
☛➢
Press Important Note
Symbols

6
ENG
Viewing the Plasma Display
POWER
Press to turn the PDP on
and off.
Speaker Speaker
Remote Control Signal Receiver
Aim the remote control towards this spot
on the PDP.
Front Panel
Rear Panel
DISPLAY SIGNAL IN
Connect the video cable between the PDP
and Media Station.
POWER IN
Plug the mains lead into an appropriate
socket.
SOURCE External input selection.
MENU Menu display.
- +Volume adjustment.
▼ C/P. ▲Channel selection
MUTE Temporary sound switch off.
➢For further details, refer to “Switching On and Off” on page 15.
➢
The actual configuration on your PDP may be different, depending
on your model.

7
ENG
Viewing the Media Station
Front Panel
Rear Panel
b
a
d
c
f
h
j
i
k
g
lm
e
Headphone connector
S-Video input
Audio inputs
Video input
Stand by /Power On indicator
On-Screen display
Temporary sound switch off
External input selection
Menu display
Volume adjustment
Power On/Off
Channel selection
a) VHF/UHF (75Ω)
75ΩCoaxial connector for Aerial/Cable Network.
b) AV1 / AV2 / AV3
Inputs or outputs for external devices, such as VCR,
DVD, video game device or video disc players.
c) AV4 (S-VIDEO / L-AUDIO-R)
Video and audio inputs for external devices with an
S-Video output, such as a camcorder or VCR.
d) COMPONENT 1 / COMPONENT 2
Video (Y/PB/PR) and audio (L/R) inputs for
Component. (480i/480p, 576i/576p, 720p, 1080i)
➢720p and 1080i are not available in DVD
mode. For further details, refer to “Preset
Signals” on page 51.
e) SURROUND OUT
Surround amplifier (S-L/S-R) or powered speaker
(CENTER/SUB-WOOFER) connection to take full
advantage of the surround sound effect.
f) AUDIO OUT (L/R)
Audio outputs for an audio system.
g) EXTERNAL SPEAKER OUT (8Ω)
Connectors for external speakers.
h) PC IN
PC video input.
i) L-AUDIO-R
PC/DVI audio inputs.
j) DVI IN
Video input for device with DVI output.
k) DISPLAY SIGNAL OUT
Output of input signal for display.
l) POWER OUT
Power output.
m) POWER IN
Power input.
➢For further details about connection, refer to pages 48~51.
➢
The actual configuration on your PDP may be different, depending
on your model.

8
ENG
Remote Control Buttons
Power
AUTOMATIC SWITCH-OFF
VCR/DVD FUNCTIONS;
- STOP (Stop)
- REWIND (Rew)
- PLAY/PAUSE (Play/Pause)
- FAST FORWARD (FF)
POWER ON/OFF
NUMERIC BUTTONS
TEMPORARY SOUND SWITCH OFF
VOLUME DECREASE
DISPLAY INFORMATION/
TELETEXT REVEAL
SOUND EFFECT SELECTION
PICTURE EFFECT SELECTION
STILL THE MAIN PICTURE
➢In the PIP mode, the main and sub
pictures are stilled at the same time.
PICTURE SIZE/
TELETEXT SIZE SELECTION
VOLUME INCREASE
CONTROL THE CURSOR IN THE MENU
MENU DISPLAY/
TELETEXT INDEX
MAKE THE REMOTE CONTROL WORKS
FOR TV, VCR, CABLE, DVD PLAYER
EXTERNAL INPUT SELECTION/
TELETEXT HOLD
➢It is possible that the work of the transmitter is dull or not operated normally
if the light of the Bulb is on around the PDP.
PIP FUNCTIONS;
-PIP ACTIVATING OR DEACTIVATING
(PIP ON)
-SWAPPING THE MAIN AND THE SUB
PICTURE (Swap)
-SELECTING THE LOCATION OF SUB
PICTURE (Locate)
-SELECTING THE CHANNEL OF SUB
PICTURE (P▲/▼)
-SETTING THE SIZE OF SUB PICTURE
(Size)
-SELECTING THE INPUT SOURCE
(Source)
-SCANNING THE CHANNEL OF SUB
PICTURE (Scan)
CHANGE CONFIRMATION
ONE, TWO, OR THREE-DIGIT CHANNEL
SELECTION
FASTEXT TOPIC SELECTION
NEXT CHANNEL/
TELETEXT NEXT PAGE
PREVIOUS CHANNEL/
TELETEXT PREVIOUS PAGE
SOUND MODE SELECTION/
TELETEXT CANCEL
TELETEXT SUB CODE
TELETEXT ON
VIDEO & TEXT
MIX
TELETEXT OFF
(Refer to page 45 for details)

9
ENG
continued...
You must insert or replace the batteries in the remote control when
you:
◆Purchase the PDP
◆Find that the remote control is no longer operating
correctly
1Remove the cover on the rear of the remote control by pressing
the symbol downwards and then pulling firmly to remove it.
2Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆+on the battery against +on the remote control
3Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
➢Do not mix battery types, i.e. alkaline and manganese.
Inserting the Batteries in the Remote Control
Installing the Display on the Wall Attachment Panel
◆ Do not install the PDP on any place other than vertical walls.
◆ To protect the performance of the PDP and prevent troubles, avoid the
followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high voltage.
- Do not install on the wall.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
Installation Notes
➢Wall attachment panel is sold separately. Check with your dealer.

10
ENG
Installing the Display on the Wall Attachment Panel
➢Wall attachment panel is sold separately. Check with your dealer
1Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to
support the PDP, strengthen the wall before installation.
2Fix the wall attachment panel on the
wall using bolts as shown in the figure:
Fixing bolts must protrude from the
wall appox. 1.5 cm.
3Using the wall attachment panel, you may adjust the angle of the display from 0 to 20 degrees. The
angle can be set in 5 stages with 5 degrees of distance each using the angle control holes on the sides
of the panel.
When the angle has
been set to 5 degrees. When the angle has
been set to 15 degrees. When the panel hasn't been tilted.
5 degrees of tilt
10 degrees of tilt
15 degrees of tilt
No tilt
20 degrees of tilt
Angle control holes

11
Installing the Display on the Wall Attachment Panel
ENG
4Remove four large screws from the rear side of the display.
Insert the bolts, dish-type washers, and insulation rubber
into the four screw-holes as shown in the figure:
5Hang the protruding plastic part on
the rear of the PDP up the groove on
the top of the wall attachment panel.
Then, lift down the PDP. (Do not lift
down the PDP with too much force.
The protruding plastic part might be
taken off.)
Bolt
Insulation rubber
´
Œ

12
ENG
Separating the Display from the Wall Attachment Panel
After lifting the PDP up, pull it forward and remove it from the wall attachment panel.
´
Œ

13
ENG
Connecting Speakers
Rear of the Media Station
➣◆The speakers MUST have more than 15watts rating (impedance 8Ω).
◆The ferrite cores are used to attenuate undesired signals. When you connect the speaker wire to the
EXTERNAL SPEAKER OUT (8Ω)connector, bind the speaker wire round the ferrite core to secure it.
Connecting PDP and Speakers
Fix the bracket onto the guide
pole located on the rear of
speaker and fasten the screws.
After removing the three
screws on the PDP, clamp the
speaker and the PDP together
and fasten the screws.
Guide pole
Guide pole
➢When moving your PDP, do NOT hold the
speaker connected to your PDP.
It may damage the bracket clamping the
speaker and your PDP together and
result in a drop of your PDP and a risk of
personal damage and injury.
Connecting Stand and Speakers
Guide pole
Rear of the PDP
Connect the speaker audio cable to the external speaker output
jack on the rear of the Media Station matching the “
+ ” and “ - ” ends
of the cable with the diagram on the Media Station.

14
ENG
Connecting to an Aerial (or Cable Television Network)
To view television channels correctly, a signal must be received by
the set from one of the following sources:
◆An outdoor aerial
◆A cable television network
◆A satellite network
1In the first three cases, connect the aerial or network input cable to
the 75Ωcoaxial socket on the rear of the Media Station.
2If you are using an indoor aerial, you may need to turn it when
tuning your television until you obtain a picture that is both sharp
and clear.
For further details, refer to:
◆“Storing Channels Automatically” on page 20
◆“Storing Channels Manually” on page 22
Rear of the
Media Station
Cable Television
Network
or

15
Switching On and Off
ENG
If your Media Station isn’t turned on when the power button is
pressed, please check if the “TV” mode has been chosen by
pressing the “Select” button.
1Plug the mains lead of the PDP and Media Station into an appropriate socket.
2Connect the video cable between the DISPLAY SIGNAL IN on the rear of the PDP and the DISPLAY
SIGNAL OUT on the rear of the Media Station.
3Press the POWER button on the front panel of the Media Station or remote control to switch the display on.
Rear of the Media Station
- Video Cable
Rear of the PDP
- Power cord
- Power cord
☛◆If you have purchased this PDP in the
United Kingdom, refer to page 57 for
further instructions on plug wiring.
◆Do not connect the power cord
between PDP and Media Station.
Otherwise, the EMI characteristic will
become worse because power input
and output signals interrupt each other.
◆The ferrite core is used to attenuate
undesired signals. When you connect
the power cord to the POWER IN
connector on the rear of the Media
Station, bind the power cord round the
ferrite core to secure it.

16
ENG
The remote control is used mainly to:
◆Change channels and adjust the volume
◆Display the on-screen menu system
The following table presents the most frequently used buttons and
their functions.
Button Viewing Function Menu Function
Used to display the next -
Pstored channel.
PUsed to display the -
previous stored channel.
to Used to display the corresponding channels.
➢For double digit channels, the second digit must be
pushed immediately after the first. Failure to do this will
result in a single digit channel being displayed.
-/--/--- Used to select a channel numbered ten or over.
Press this button, and enter the two or three-digit channel
number.
Used to increase the -
volume.
Used to decrease the
-
volume.
Mute Used to switch the sound off temporarily.
➣To turn the sound back on, press this button again, or
press the
- or +button.
Menu Used to display the Used to return to the previous
on-screen menu system. menu or normal viewing.
- Used to:
◆Display a submenu
containing selections for
the current menu option
◆Search forwards/
backwards manually for
channels
◆Increase/decrease a
menu option value
- Used to confirm your choice.
Becoming Familiar with the Remote Control
Power

1Turn off your VCR, Cable box, or DVD.
2Press the Select button repeatedly to activate another component
(VCR, Cable, DVD).
Example:If you want to program the remote control to operate
your VCR, make sure that the VCR LED is
illuminated.
3Press the Power button on the remote control. The component you
select should turn on. If it turns on, your remote control is now set
correctly.
4Once your remote control is set up, press the Select button any
time you want to use the remote control to operate your VCR,
Cable box, or DVD.
➣◆When your remote control is in the VCR, Cable, or DVD
mode, the volume buttons still control your Media
Station’s volume.
◆When your remote control is in the TV or Cable mode,
the VCR control buttons (PLAY, PAUSE, etc.) still
operate your VCR.
17
ENG
Setting up your Remote Control

18
ENG
When the Media Station is initially powered ON, several basic
customer settings proceed automatically and subsequently. The
following settings are available.
1If the Media Station is in Standby mode, press the Power button on
the remote control.
Result:The message Plug & Play is displayed. It flickers for
a little while, and then the Language menu is
automatically displayed.
2Select the appropriate language by moving the joystick left or
right. Press the MENU button.
Result:The message Antenna input check is displayed.
It flickers for a little while, and then the Country menu
is displayed. Make sure that the antenna is connected
to the Media Station.
3Select your country by moving the joystick left or right.
Result:The following countries are available.
Austria - Belgie - Croatia - Denmark -
Finland - France - Deutschland - Iceland -
Ireland - Italia - Nederland - Norway -
Poland - Espania - Sverige - Schweiz -
Türkiye - UK - Others
➣If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually
(see page 22).
4To start the store, press the joystick button.
Result:The search is start. During searching, the status bar is
displayed and the search will end automatically.
➢To stop the search before it has finished or return to normal
viewing, press the MENU button.
5When it has finished, the message Enjoy your watching is
displayed, and then the channel which has been stored will be
activated.
Plug and Play
Plug & Play
Language English
Menu
Select
Antenna input check
Country Austria P 6
44 MHz 1 %
Menu
Enjoy your watching
Country Austria
Menu
Select Store

19
When you start using your PDP for the first time, you must select
the language which will be used for displaying menus and
indications.
1Press the MENU button.
Result:The main menu is displayed.
2Move the joystick up or down until the Function is selected.
Result:
The options available in the Function group are
displayed.
3Press the joystick button.
Result:
The Language is selected.
4Select the appropriate language by moving the joystick left or
right.
Choosing Your Language
ENG
Move
Function
Language
Time
Size
Image Lock
AV Setup
Melody
English
Normal
On
Select Menu

20
ENG
Move
Channel
Country
Auto Store
Manual Store
Channel Sort
Channel Edit
Fine Tune
Austria
Menu
Select
You can scan for the frequency ranges available to you, (availability
depends on your country). Automatically allocated programme
numbers may not correspond to actual or desired programme
numbers. However you can sort numbers manually and clear any
channels you do not wish to watch.
1Press the MENU button.
Result:The main menu is displayed.
2Move the joystick up or down until the Channel is selected.
Result:
The options available in the Channel group are
displayed.
3Press the joystick button.
Result:
The Country is selected.
4Select your country by moving the joystick left or right.
Result:The following countries are available.
Austria - Belgie - Croatia - Denmark -
Finland - France - Deutschland - Iceland -
Ireland - Italia - Nederland - Norway -
Poland - Espania - Sverige - Schweiz -
Türkiye - UK - Others
➣If you have selected the Others option but do not wish to
scan the PAL frequency range, store the channels manually
(see page 22).
5Move the joystick up or down until the Auto Store is selected.
Press the joystick button to start the search.
Result:The search will end automatically. Channels are sorted
and stored in an order which reflects their position in
the frequency range, (with lowest first and highest last).
The programme originally selected is then displayed.
➣To stop the search before it has finished, press the Menu
button.
6When the channels have been stored, you can:
◆Sort them in the order required (see page 21)
◆Assign a name to the stored channels (see page 24)
◆Add and erase the channels (see page 24)
◆Lock the channels (see page 24)
◆Activate the LNA (Low Noise Amplifier) feature (see page 24)
◆Fine tune channel reception if necessary (see page 25)
Storing Channels Automatically
Move
Channel
Country
Auto Store
Manual Store
Channel Sort
Channel Edit
Fine Tune
Austria
Menu
Enter
Country Austria P 6
44 MHz 1 %
Menu