Samsung Harman AMX VARIA-ACS-810A User manual

QUICK START GUIDE
VARIA-ACS-810A 8” & 10.1” Angle-Select Tabletop Stand
VARIA-ACS-150A 15.6” Angle-Select Tabletop Stand
Overview
The Varia Angle-Select Tabletop stands are designed for 8” VARIA-80, 10.1”
VARIA-100, & 15.6” VARIA-150 Touch Panels, and give them a sleek & modern
tabletop solution that can be installed at one of three angles to best suit the
users’ needs.
FIG. 1 Varia Touch Panel on Angle-Select Tabletop Stand
Model Availability & Compatibility
ANGLE-SELECT TABLETOP STANDS
VARIA-ACS-810A
(AMX-UMT8111)
VARIA-80 Touch Panel (AMX-UTP0811)
VARIA-100 Touch Panel (AMX-UTP1011)
VARIA-100N Touch Panel (AMX-UTP1011N)
VARIA-ACS-150A
(AMX-UMT1511)
VARIA-150 Touch Panel (AMX-UTP1511)
VARIA-150N Touch Panel (AMX-UTP1511N)
Other Models Available
FIXED TABLETOP STANDS
VARIA-ACS-80F
(AMX-UMT0801) VARIA-80 Touch Panel (AMX-UTP0811)
VARIA-ACS-100F
(AMX-UMT1001)
VARIA-100 Touch Panel (AMX-UTP1011)
VARIA-100N Touch Panel (AMX-UTP1011N)
Installation
Varia Fixed Tabletop Stands are easily installed with the supplied hardware and
a Philips-head screwdriver.
1. Place the panel face-down on a soft cloth and arrange the panel so
that the top of the touch panel is closest to you.
FIG. 2Varia Touch Panel, rear
2. Unscrew the lower back cover from the touch panel.
Screw Locations
FIG. 3Rear cover screws
3. While putting pressure on the rectangular access holes, push the
lower cover away from you. Do not discard, this will be reinstalled
later.
FIG. 4Lower Cover
4. Rotate the panel back around so the bottom is closest to you.
5. Route the networking cable through the base first, and then plug the
RJ-45 connector into the back of the touch panel.
FIG. 5Tabletop Stand Base
6. Reinstall the lower cover, first snapping it into place and then
securing it with the two screws. Make sure the cable routes out the
bottom of the lower cover.
7. Screw the mount to the rear of the panel using the supplied screws.
FIG. 6 Mounting Plate Installation
NOTE: The three slots should be oriented UP and the set screw
holes should be oriented DOWN.
Top
Top

QUICK START GUIDE
VARIA-ACS-810A 8” & 10.1” Angle-Select Tabletop Stand
VARIA-ACS-150A 15.6” Angle-Select Tabletop Stand
© 2023 HARMAN. All rights reserved. SmartScale, NetLink, Enova, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered
trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective
companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time. The
AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax [phone]
1000374846 REV:C
Last Revised 2023-03-23
FIG. 7Mounting Plate; Slot & Set Screw Locations
8. Select the best angle for installation. The Angle-Select Tabletop Stand
can be installed at one of three (3) angles:
a. Upright 60° angle
b. Mid 45° angle
c. Low 30° angle
30° position
[Most Horizontal]
45° position
60° position
[Most Upright]
FIG. 8Mounting Plate; Install Angle Options
9. Insert the base into the desired position. Insert the tab first and set
flat against the mount.
10. Install the supplied set screw to lock the base in the desired position.
FIG. 9Varia Touch Panels on Angle-Select Tabletop Stand, various angles
Removing
To remove the panel, follow the installation directions in reverse.
Slots
Set Screws