Samsung SBP-300NB User manual

INSTALLATION BOX
User Manual SBP-300NB

Copyright
©2014 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
INSTALLATION BOX
User Manual

English _3
overview
CONTENTS
OVERVIEW
3
4What’s Included
INSTALLATION & CONNECTION
6
6Installation
APPENDIX
12
12 Specification
12 Product Overview

overview
4_ overview
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance Item Name Quantity
INSTALLATION BOX 1
INSTALL BRACKET 1
Gasket (for SBP-300WM1) 1
Gasket (for SBP-300WM) 1
RUBBER HOUSING 1
BRACKET ADAPTOR 1

English _5
Appearance Item Name Quantity
MOUNT CAP 5
MOUNT CAP fastener 1
M10 x L22 screw (to attach the install bracket) 4
M8 x L20 screw (to attach the housing) 4
M3 x L6 screw
(to attach the bracket adaptor and media convert) 4
M10 x L12 wrench bolt (to attach SBP-300WM) 4
M10 x L20 wrench bolt (to attach SBP-300WM1) 4
M4 x L8 screw (to attach the media convert) 2

6_ installation & connection
installation & connection
INSTALLATION
1. Push the locking lever on the door to separate the housing and door.
2. Undo the four screws to separate the bracket adaptor.
Lock the unused piping hole with the attached mount cap.
Use a mount cap fastener to attach the mount cap.
BRACKET
ADAPTOR
Mount cap
fastener Mount cap
DOOR
HOUSING
LOCKING
LEVER
LOCKING LEVER

English _7
3. Remove the double-sided tap on the rear side of the gasket and affix it to the door.
Attach the wall mount to the door using the four M10 screws.
< Tighten each of the four screws a little at a time so that the wall mount is evenly pressed
to the gasket. >
•Use of SBP-300WM1 wall mount (with M10 x L20 screws)
DOOR
GASKET
•Use of SBP-300WM wall mount (evenly securing the wall mount inside the
gasket groove as shown in the image below.) (with M10 x L12 screws)
DOOR
GASKET
GASKET
JPlease assemble
the set in such a
way that the lock tab
faces down into the
slot in the installation
direction.

installation & connection
8_ installation & connection
4. Attach the install bracket to the wall, corner mount (SBP-300KM) or pole mount (SBP-300PM)
using the M10 screws.
Only use the 4 screws included in the accessories as shown in the image below.
Screw (circular head, with M10 x L22 screw)
•Installation on the wall
•Pole Mount
•Corner Mount

English _9
5. Place the housing on the install bracket as shown in the image.
`To install it on the wall, attach the rubber housing as shown in the figure.
The rubber is not waterproof. It is decorative only, serving to hide a gap.
Therefore, if the cable is inserted into the main body separately and not through the duct on the wall, the insertion
point of the cable must be completely waterproof.
If this is not done, any water leaks may cause problems.
6. Secure the housing to the install bracket using 4 M8 screws in the same ways as "No. 4" in the
installation procedure.
Cable
Waterproofing
needed

installation & connection
10_ installation & connection
7. Insert the external cable into the main body using a pipe.
Wrap the thread of the pipe screw with Teflon tape to protect against water leakage problems.
(Make sure that water leaks will not cause a problem at the cable insertion point.)
8. Install the power adaptor and media convert using the bracket adaptor, and connect the external
cable.
CABLE
Teflon tape
Power
adaptor
BRACKET ADAPTOR
MEDIA COVERT