Samsung 46UE User manual

BN68-01537H-00
Wall Mount Setup Guide
Guide de montage mural
BN68-01537H-00.indb 1 2012-10-29 오후 5:22:58

Contents
Safety Precautions
Safety Precautions 01
Introduction
Unpacking 02
Attaching the bracket ⓐ to the monitor 03
Mounting the bracket ⓑ onto a wall 04
Different bracket types by product models
and specications 05
Arranging the monitors 07
Fine tuning 08
Detaching the monitors 10
Product specications
Product specications 12
Product drawings
Product drawings 13
BN68-01537H-00.indb 1 2012-10-29 오후 5:22:58

English 1
Safety Precautions
The information contained herein is for your safety and
to prevent any loss of property.
Please read the instructions carefully to use the prod-
uct correctly.
This mandatory sign is used to emphasize
the instructions that must be observed.
* Failure to observe the instructions herein can cause serious injury or death.
1. Be sure to contact an installation expert authorized by your dealer to perform the installation.
• Installation by a non-professional may cause personal injury.
If you are planning to relocate or replace the product
after installation, be sure to consult with an installation
expert authorized by your dealer.
After installation, do not apply excessive force or
physical pressure on the product.
2. Do not let your children play in the vicinity of the product.
• They may bump their head or body against the corner of the product and suffer personal injury.
3. Be careful not to let the back of the product hit against the wall when it is rotated or the angle is adjusted.
• You can protect the wall and product from any damage by attaching a piece of sponge to each corner of the product.
4. Do not install the product on a wall that cannot bear the weight of the product.
• The product may fall, and get damaged or cause personal injury.
5. Products installed in unusual, abnormal or extreme areas may be subject to serious performance problems due to the
surrounding environment. Be sure to consult with a Samsung service center before installing the product in such an
area.
• Areas exposed to an excessive amount of ne particles or moisture, chemicals, extreme temperatures, high humidity,
automobiles, etc.
English
BN68-01537H-00.indb 1 2012-10-29 오후 5:22:58

English 2
Unpacking
Monitor-mount bracket ⓐWall-mount bracket ⓑBracket-Bar 400 & 600
Screw ⓐ
(M8 X L30) : 8EA
Screw ⓑ
(M4 X L8) : 5EA
Wood screw
10EA
Screw holder : 4EA
(UE) Screw holder : 4EA
(UD)
Screw holder : 4EA
(ME75) Safety fastener : 2EA
BN68-01537H-00.indb 2 2012-10-29 오후 5:22:59

English 3
Attaching the bracket ⓐ to the monitor
1. Assemble the four screws ⓐ and the screw holders, and fasten them to x the bracket ⓐ to the monitor as shown in
the picture below.
(M8 X L30)
* Check to conrm that the bracket ⓐ is fastened to the monitor.
MOUNTING ME75
(ME75)
(ME75)
(UE)
NUse the screw holder for UD models when attaching brackets to ME65.
NUse the screw holders for ME75 and UE models when attaching brackets to ME75.
BN68-01537H-00.indb 3 2012-10-29 오후 5:22:59

English 4
Mounting the bracket ⓑ onto a wall
1. Using the two screws ⓑ, x bracket bar 400 or 600 according to the product model as shown in the image.
2. Fix the bracket ⓑ tightly against the wall using the wood screws.
* Ensure you check the wall strength, and do the reinforcing work before installation if the wall is not sufciently
strong.
* The provided screws are for wood.
* Check the wall and use proper screws according to the material of the wall, such as marble, steel plate or concrete.
NIf it is difcult to fasten the screws into the specic holes, fasten the screws in the adjacent holes.
* When drilling a hole into a wall, make sure
you use a drill bit and drill of the specied
diameter.
Otherwise, there may be safety problems.
1. Make a hole using a
3 X 50 drill.
2. Clean the inside of the
drilled hole.
3. Fasten the wood screw into
the hole.
HOW TO FASTEN A SCREW
Bracket-Bar 400
BN68-01537H-00.indb 4 2012-10-29 오후 5:23:00

English 5
Different bracket types by product models and
specications
PRODUCT MODELS AND SPECIFICATIONS
Model VESA Standard Mounting Type Monitor-Mount Bracket Bracket-Bar
46UE 400*400
LAND 400 400
PIVOT 400 400
55UE 400*400 LAND 400 400
PIVOT 600 400
46UD 600*400 LAND 400 600
PIVOT 600 400
55UD 600*400 LAND 400 600
PIVOT 400 400
65ME 400*400 LAND 400 400
PIVOT 400 400
75ME 400*400 LAND 400 400
PIVOT 400 400
CHANGING THE MONITOR-MOUNT BRACKET TYPE FROM 400 TO 600
1. Unfasten the four screws from monitor-mount
bracket type 400 as shown in the image.
2. Extend the bracket and fasten the four screws.
* Use the appropriate bracket type based on the product model and specications.
BN68-01537H-00.indb 5 2012-10-29 오후 5:23:00

English 6
INSTALLING THE VIDEO WALL
4
1 2
3
* Before you install on the Video Wall, check the wall strength considering the total weight of the monitors and
brackets you want to install.
Weight of a bracket: 3.2 kg
* If you intend to install on a Video Wall that is four layers or more, take into consideration the air conditioning
system. Consult with an expert before installation as heat from the monitors may cause problems.
NInstalling the Video Wall should be done by two persons or more.
BN68-01537H-00.indb 6 2012-10-29 오후 5:23:00

English 7
Arranging the monitors
1. Hook the monitor to which the bracket ⓐ is attached on the poles of the wall-mount bracket ⓑ.
* Be sure not to put pressure on the panel with your hands when handling the monitor.
Otherwise, you may break the panel.
2. To prevent the monitor from becoming loose, fasten the safety fasteners using the screws ⓑ.
Fasten them on both sides.
(M4 X L8)
* Since the monitor may fall during installation, ensure you fasten the safety fasteners on both sides.
* Ensure the hooks are
suspended securely on
the poles.
BN68-01537H-00.indb 7 2012-10-29 오후 5:23:01

English 8
3. Arrange the monitor on each bracket following steps 1 and 2.
* Be careful not to catch your nger during installation.
Fine tuning
NAfter arranging the monitors, if they do not seem well-
proportioned, adjust them using the ne-tuning screws
on the brackets.
NBe sure not to leave any height differences or gaps
between the monitors.
1. Correcting height difference between the front and back
of a monitor.
• At the same time, pull the knob and turn the
adjustment screw clockwise.
The monitor will move forward.
To move the monitor backward, turn the screw
counterclockwise.
The ne-tuning screw’s maximum movement range is
5 mm.
Knob
<Moving the monitor forward> <Moving the monitor backward>
BN68-01537H-00.indb 8 2012-10-29 오후 5:23:02