Samsung AV-R700 User manual

ELECTRONICS
Instruction Manual
Digital Surround
AV Receiver System
AV-R700
AH68-01597B

21
Safety Warnings Precautions
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install
your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the
ventilation slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other
equipment which may become hot. Before moving the player, ensure the disc tray is empty. This player is designed for
continuous use. Switching off the DVD player to the stand-by mode does not disconnect the electrical supply. In order to
disconnect the player completely from the power supply, remove the main plug from the wall outlet, especially when left unused
for a long period of time.
Protect the player from moisture(i.e. vases) , and excess
heat(e.g.fireplace) or equipment creating strong magnetic or
electric fields (i.e.speakers...). Disconnect the power cable from
the AC supply if the player malfunctions. Your player is not
intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc have been
stored in cold temperatures.
If transporting the player during the winter, wait approximately 2
hours until the unit has reached room temperature before using.
During thunderstorms, disconnect AC main plug from
the wall outlet.
Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat
sources.
This could lead to overheating and malfunction of the
unit.
The battery used with this product contain chemicals
that are harmful to the environment.
Do not dispose of batteries in the general household
trash.
This symbol indicates that dangerous voltage which
can cause electric shock is present inside this unit.
This symbol alerts you to important operating and
maintenance instructions accompanying the unit.
WARNING: To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
Wiring the Main Power Supply Plug(UK Only)
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin
face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same
colour as the fuse fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should
obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the
plug to a main socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:–
BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as
follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH
THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN
AND YELLOW.
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE REAR COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified
as a CLASS 1 LASER product.
CAUTION
PREPARATION

√√ Let's find out difference between general amplifier and AV receiver!
General Amplifier
2 channels (left speaker and right speaker)
Play back music mainly
No decoder
Not play back various kinds of sound formats
AV Receiver
Multiple Channel (5.1 channel by default)
Play back music and video sound realistically
Has decoder
Dolby Pro Logic ll x
Dolby Pro Logic ll x is a new type of multiple
channel audio signal decoding method that
improves upon existing Dolby Pro Logic.
DTS (Digital Theater Systems)
DTS play backs 5.1 channel sound of wide-range
by playing sound of DVD and CD disk as surround
sound system.
DTS 96/24
DTS is the surround format implementing 5.1
channel multi channel sounds of 96KHz/24bit
without losing the image quality of DVD. In addition,
it can reproduce the matrix 6.1 of DTS 96/24
decoder signal.
DTS-ES
DTS-ES is the surround format implementing
surround type of discrete 6.1 channel while
preserving upper compatibility in response to
existing DTS Digital Sound format.
It is the latest digital sound format maximizing the
space quality and 360 surround experience by
adding rear center channels.
DOLBY DIGITAL EX
It not only significantly enhances space expression
capability of surround channel but also easily
implements the sound localization at the rear
according to sound field reproduction at 6.1 channel
including rear center channel.
DTS
It reproduces the digital PCM or analog stereo
sound source in 6.1 channels using the high
precision digital matrix of DTS only.
It refers to home theater exclusive amplifier by amplifying the audio signal from DVD and CD player as a core element of
home theater.
√√ What is AV receiver?
Features Contents
43
Play back various kinds of sound formats including Dolby
Digital and DTS
Many input/output connectors
No noise using digital signal type
PREPARATION
Safety Warnings ..............................................................................................................1
Precautions......................................................................................................................2
Features ..........................................................................................................................3
Contents ..........................................................................................................................4
Description ......................................................................................................................5
CONNECTIONS
Connecting the Speakers ...............................................................................................9
Connecting External Components ..................................................................................11
Connecting External Component.....................................................................................13
Connecting the FM Antenna............................................................................................14
OPERATION
Before Using AV Receivera .............................................................................................15
Selecting External Component Input ...............................................................................16
Setting the Speakera .......................................................................................................17
Setting DRC (Dynamic Range Compression) .................................................................21
Test Tone ........................................................................................................................22
Setting Speaker Level .....................................................................................................25
Dolby Pro Logic ll x Mode................................................................................................27
Dolby Pro Logic ll x Effect................................................................................................29
NEO:6 Mode....................................................................................................................31
SFE Mode........................................................................................................................33
EX/ES Mode ....................................................................................................................35
Stereo Mode ....................................................................................................................37
RADIO OPERATION
Listening to Radio ...........................................................................................................39
Presetting Radio Stations ...............................................................................................40
About RDS Broadcating ..................................................................................................41
MISCELLANEOUS
Convenient Functions .....................................................................................................43
Operating TV with Remote Control..................................................................................45
Operating VCR (DVD) with Remote Control....................................................................47
Before Calling for Service................................................................................................49
Specifications ..................................................................................................................51
Memo...............................................................................................................................52
This product is manufactured with technical cooperation with Digital
Theater Systems, Inc., is the registered trademark of Digital
Theater Systems.
(c)1996 Digital Theater Systems, Inc. All rights Reserved.
Manufacturedunderlicense from Dolby Laboratories.
“Dolby”, “ProLogic” and double-D symbol are the trademark of Dolby Laboratories.
Confidential unpublished works
(c)1992-1997 Dolby Laboratories. All rights are Reserved.
PREPARATION

Description
[ Front Panel ]
[ Display ]
POWER button EXTERNAL VIDEO
INPUT CONNECTOR VOLUME CONTROL
REMOTE CONTROL Sensor EXTERNAL OPTICAL DIGITAL
AUDIO INPUT CONNECTOR SELECTION button TUNING ( ) button
POWER STANDBY Indicator EXTERNAL AUDIO INPUT CONNECTOR SURROUND button
HEADPHONE Jack INPUT button
65
S.W
SPEAKER INDICATOR
SUBWOOFER
LEVEL INDICATOR DOLBY PRO LOGIC
IIX
INDICATOR
VARIOUS
FUNCTION
INDICATOR
RADIO BROADCASTING
RECEIVING INDICATOR
RADIO STEREO INDICATOR
ANALOG INDICATOR
RADIO FREQUENCY
INDICATOR
OPTICAL DIGITAL
INDICATOR
DTS ES 96/24
INDICATOR LIVE SURROUND
INDICATOR L.PCM INDICATOR
NEO:6
INDICATOR DOLBY DIGITAL EX
INDICATOR MPEG2
INDICATOR COAXIAL DIGITAL INDICATOR
DVD VIDEO INPUT
CONNECTOR
COOLING PAN
SAT VIDEO INPUT
CONNECTOR
5.1 CH ANALOG
AUDIO CONNECTOR
VCR VIDEO INPUT CONNECTOR
AM ANTENNA
CONNECTOR VCR VIDEO OUTPUT CONNECTOR
MONITOR VIDEO OUTPUT
CONNECTOR
FM ANTENNA
CONNECTOR
OPTICAL DIGITAL AUDIO OUTPUT
CONNECTOR
DVD OPTICAL DIGITAL AUDIO INPUT CONNECTOR
SAT OPTICAL DIGITAL AUDIO
INPUT CONNECTOR
CDCOAXIAL DIGITAL
AUDIOINPUT
CONNECTOR
SAT S-VIDEO INPUT CONNECTOR
VCR S-VIDEO INPUT CONNECTOR
VCR S-VIDEO OUTPUT CONNECTOR
CENTER SPEAKER TERMINAL
FRONT SPEAKER TERMINAL
REAR SPEAKER TERMINAL
MONITOR S-VIDEO OUTPUT CONNECTOR
[ Rear Panel ]
Accessories
√√ œœ
USER’S GUIDE
CD AUDIO INPUT CONNECTOR
DVD AUDIO INPUT CONNECTOR
SAT AUDIO INPUT CONNECTOR
Remote Control
FM Antenna User’s Manual
Battery(AAA Size 1.5V) AM Antenna
VCR AUDIO INPUT CONNECTOR
VCR AUDIO OUTPUT CONNECTOR
SUBWOOFER OUTPUT CONNECTOR 1
SUBWOOFER OUTPUT CONNECTOR 2
,
DVD S-VIDEO
INPUT
CONNECTOR
PREPARATION

Description
VOLUME CONTROL button
MUTE button
MENU button
ANALOG/DIGITAL button
POWER button
SLEEP button
TUNER button
NEO : 6 button
EXTERNAL DEVICE PLAYBACK button
DISPLAY button
MODE button
Direct Function Select button
TV Indicator
VCR Indicator
AV RECEIVER Indicator
TV/VIDEO
, FUNCTION button DVD Indicator
MODE button
MO/ST button
SUBWOOFER button
SFE MODE button
EX/ES button
EFFECT button
STEREO button
MOVE/SELECT button
TUNER MEMORY button
TUNING/CHANNEL button
SPEAKER LEVEL button
TEST TONE button
SPEAKER SETUP button
SPEAKER DISTANCE button
RDS Selection button
[ Remote Control ]
87
To open the remote control cover,
push the top of the cover, then slide
downward.
Insert Remote Batteries
The remote control can be used up to approximately 23
feet/7 meters in a straight line. It can also be operated at
a horizontal angle of up to 30° from the remote control
sensor.
Range of Operation of the Remote Control
Remove the battery
cover on the back of
the remote by
pressing down and
sliding the cover in
the direction of the
arrow.
1
Insert two 1.5V AAA
batteries, paying
attention to the correct
polarities (+ and –).
2
Replace the battery
cover.
3
Follow these precautions to avoid leaking or cracking batteries:
•
Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).
•
Use the correct type of batteries.Batteries that look similar may differ in voltage.
•
Always replace both batteries at the same time.
•
Do not expose batteries to heat or flame.
Caution !
PREPARATION
Number(0~9) buttons

Connecting the Speakers
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
• Place the rear left and right speaker at the interval of front
left and right speaker.
• If there isn't enough now, place rear speakers to face
down other.
• Place the rear speakers about 70 cm to 1 m above your
ear, facing slightly downwards.
❈ Unlike the front and center speakers, the rear speakers
and used to mainly sound effects and sound will not
come from them all the time.
Rear Speakers
• If you place 1 rear center speaker, place it so that it faces
forward from the back of listener.
• Place the rear center speaker about 70 cm to 1 m above
rear speakers, facing slightly downwards.
Rear Center Speaker
SL SR
SB
• Adjust the angle of front left and right speakers so
that it can form 30 degree to the left and right from
the listening position.
• Place the speakers so that their tweeters will be at
the same height as your ear.
• Align the front face of the front speakers with the
front face of the center speaker or place them
slightly in front of the center speaker.
Front Speakers
• It is best to install center speaker at the same height as
the front speakers.
• You can also place center speaker directly over or
under the TV.
Center Speaker
• Place AV Receiver on the dedicated stand or chest of
living room or under the TV stand properly.
Position of AV Receiver
• The position of the subwoofer is not so critical. Place it
anywhere you like.
•
Usually, it is placed by a corner near the front speakers.
Subwoofer
When you place the speaker on the wall, make sure
to fasten it tightly so that it may not fall off.
109
Caution!
CONNECTIONS
• Never touch speaker terminals while
the power is on. Doing so could
result in electric shock.
• Make sure the polarities (+ and -)
are correctly.
1
√ Connecting Front Speaker Wire
√ Connecting Center/Rear Speaker Wire
PASSIVE
SUBWOOFER
ACTIVE SUBWOOFER
(BUILT-IN POWER
AMPLIFIER)
POWER
AMPLIFIER
FRONT (R)
FRONT (L)
REAR(R) REAR(L)
MAIN UNIT
AV-R700
CENTER REAR CENTER
Caution!
Turn and loosen the
speaker connector. 2
1Press the tab of the
speaker connector. 2Insert the black wire into the black(-)
terminal and the red wire into the
red(+) terminal.
3Turn and fasten the
speaker connector.
Insert the black wire into the black(-)
terminal and the red wire into the
red(+) terminal.

Connecting External Components
DIGITAL
OUT
AUDIO
OUT
VIDEO
OUT
S-VIDEO
OUT
LR
AUDIO
IN
AUDIO
OUT
VIDEO
OUT IN
S-VIDEO
OUT IN
LRLR
S-VIDEO
IN
VIDEO
IN
S-VIDEO
IN
DIGITAL
OUT
AUDIO
OUT
VIDEO
OUT
S-VIDEO
OUT
LR
DIGITAL
IN
DVD Player
Video Projector SAT Player Video Player
TVMD Player
• Disconnect the power plug from the outlet if you do not use this unit for long period of time.
• If the Audio Output connector of external
component is only 1, connect Audio Output
connector or external component to either of
Audio Input connector (right or left) of main unit.
• Connect the red cable of audio cable to red
connector and white cable to white connector.
• When you connect Video Input connector of
external component to Video Output connector
of main unit, connect Video Input connector of
external component either to Video Output
connector or S-Video Output connector.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting Video Component
1211
Caution!
CONNECTIONS

Connecting External Component
LR
DIGITAL
OUT
AUDIO
OUT
FRONT SURR.
SUB
WOOFER
L
R
L
R
CENTER
CD Player
DVD or 5.1 Channel Player
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting Audio Component/ 5.1 Channel
1413
1. Connect the FM antenna supplied to the FM
75ΩCOAXIAL terminal as a temporary mea-sure.
2. Slowly move the antenna wire around until you find
a location where reception is good, then fasten it to
a wall or other rigid surface.
1. Connect the AM loop antenna supplied to the AM
and terminals.
2. If reception is poor, connect an outdoor single vinyl-
covered wire to the AM ter-minal. (Keep the AM loop
antenna con-nected).
The cooling fan dissipates the heat generated inside the unit so that the unit can
be operated normally. The cooling fan is activated automatically to supply cool air
to the unit.
Please observe the following cautions for your safety.
• Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the
unit could rise and may damage it.
• Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are
covered with a newspaper or cloth, heat may build up inside the unit and fire may result.)
Connecting the FM and AM
Antennas
FM antenna connection
If AM reception is poor, connect an
outdoor AM antenna(not supplied).
FM Antenna (supplied)
AM Loop Antenna
(supplied)
Snap the tabs on the loop into the
slots of the base to assemble the
AM loop antenna.
COOLING FAN
AM antenna connection
CONNECTIONS

Before Using AV Receiver
Turning On/Off
Functions of Dedicated Remote Control
Connect the power plug to the outlet.
1
Press the POWER ( ) button of the main unit.
• This unit will be turned on or off.
2
MAIN UNIT
REMOTE CONTROL
Press MODE button.
• Each time you press this button, it will select and blink TV indicator ➝VCR indicator
➝DVD indicator ➝AV Receiver indicator in turn.
• You can operate TV after TV indicator blinking.
You can operate VCR after VCR indicator blinking.
You can operate DVD after DVD indicator blinking.
You can operate AV Receiver after AV Receiver indicator blinking.
• This unit will not turned on or off even if you press the POWER ( ) button of
remote controller while main unit is turned off.
• When you turn off the power by pressing the POWER ( ) button of remote
control, this unit will be standby mode.To completely turn off the power, press the
POWER ( ) button of the main unit. Standby indicator will be turned off.
• Basic operation of remote control is set up based on Samsung products.
Refer to page 45~48 for more details on operation method.
You can operate TV, VCR, DVD, AV Receiver with one remote control.
You can listen ti sound in Analog 2 Channels or Dolby Digital 5.1 Channel using this unit.


1615
Press the FUNCTION button.
• When you select the audio external component (external component without
Video Output connector), the image of video external component (external
component with Video Output connector) used last will appear in the TV screen.
• You can watch the image of video external component while listening to sound of
audio external component.
Selecting External Component Input
• You can enjoy Dolby Digital effect only if you connect Audio Output connector of
external audio component to optical/coaxial digital Audio Input connector of main unit.
To set the menu function of external component
Press the MENU button.
• Menu setup screen of TV, VCR and DVD Player will appear.
REMOTE CONTROL
To Select the Function
To Select Analog/Digital Input
REMOTE CONTROL
• You can directly select 5.1CH, VCR, DVD, CD, SAT, or AUX.
• For DVD, SAT, AUX Function
ANALOG and OPTICAL (1, 2, 3) will be selected repetitively.
• For CD Function
ANALOG and COAXIAL will be selected repetitively.
MAIN UNIT
REMOTE CONTROL
Press INPUT button.
• Each time you press the this button, 5.1CH MULTI CH ➝CD ➝DVD ➝SAT ➝VCR ➝AUX
➝FM ➝AM will be selected in turn.
Press the ANALOG/DIGITAL button.
• You can operate this function only with remote controller.
• This function will be selected in analogue only for VCR function, and will not work for 5.1CH MULTI CH function.
Caution!
Press the POWER ( ) button of the remote control while main unit is turned on.
• This unit will be turned on or off.
Method 1
Press DIRECT FUNCTION Select button.
Method 2
Press the FUNCTION button.
• Each time you press the this button, 5.1CH MULTI CH ➝CD ➝DVD ➝SAT ➝VCR ➝
AUX ➝FM ➝AM will be selected in turn.
OPERATION

Setting the Speaker
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.Signal outputs
and frequency response from the speaker will automatically be adjusted according to your speaker configuration
and whether certain speakers are used or not.
Press SPK SEL. button to select the speaker you want.
• Each time you press this button, F.SPK ➝C.SPK ➝S.SPK ➝SB SPK ➝
SW SPK ➝CROVR ➝SPK MODE OFF will be selected in turn.
Press …† button to set the speaker as you want.
Repeat the steps 1 and 2 to set the speaker.
To Exit Setup Mode
• Wait for about 5 seconds or press the SPK SEL. button of the remote control to
select SPK MODE OFF.
To Use SUBWOOFER button of Remote Control
Press SUBWOOFER button.
• Each time you press this button, SW SPK : YES, SW SPK : NO will be selected in turn.
• If you play in 2 Channel Stereo, select 'YES' to use Subwoofer and 'NO' not to use.
√
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button one time.
• “SPEAKER SETUP” appears in the display.
Press SURROUND button to select the speaker you want.
Each time you press this button, F.SPK ➝C.SPK ➝S.SPK ➝SB
SPK ➝SW SPK ➝CROVR will be selected in turn.
Press SELECT ( ) button to set the speaker as you want.
Repeat the steps 3 and 4 to set the speaker.
To Exit Setup Mode
• Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit.
“SETUP MODE OFF” appears on the display and exits Setup Mode.
• LARGE : Select when you use large speaker. You can listen to full
ranges of sound from bass to treble.
• SMALL : Select this when you use small speaker. Bass below
100ß‘ will not be output from the whole speakers but only
from subwoofer.
• NONE : Select this when you use no speaker.
• YES : Select this when you use Subwoofer Speaker if you play
back in 2 Channel Stereo.
• NO : Select when you do not use Subwoofer Speaker if you play
back in 2 Channel Stereo.
• CROVR: Select the crossover frequency depending on the size of
speaker connected when you use subwoofer. Select 40Hz
if cone paper speaker is 16cm, select 60Hz for 14cm,
80Hz for 12cm, 100Hz for 10cm, 12Hz for 8cm ,150Hz for
6cm and 200Hz for 4cm.
• If F.SPK is set to ‘SMALL’, SW SPK is fixed to ‘YES’.
•
If S.SPK is set to ‘NONE’, SB SPK is fixed to ‘NONE’.
• You cannot use Speaker Setup Mode in 5.1CH MULTI CH function.
1817
• F.SPK (Front) : LARGE, SMALL
• C.SPK (Center) : LARGE, SMALL, NONE
• S.SPK (Rear) : LARGE, SMALL, NONE
• SB SPK (Rear Center) : LARGE, SMALL, NONE
• SW SPK (Subwoofer) : YES, NO
• CROVR (Crossover Frequency): 40, 60, 80, 100, 120, 150,200Hz
Setting the Speaker
1
2
3
REMOTE CONTROL
Caution!
MAIN UNIT
1
2
4
5
3
,
OPERATION

Setting the Speaker
Press the SPEAKER DISTANCE button to select the
speaker you want.
• Each time you press this button, F.L ➝CEN ➝F.R ➝S.R ➝S.B ➝S.L ➝
S.W ➝DISTANCE OFF will be selected in turn.
Press …† button to set the speaker distance.
• For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to
listening position between 0.0~1.5m at the interval of 0.3m.
• For S. R, S.B, S.L Speaker, you can set the distance from the speaker to
listening position between 0.0~4.5m at the interval of 0.3m.
Repeat the steps 1 and 2 to set the speaker distance.
Set the distance from the speaker to listening position at the interval of 0.3m.
• F.L (Front-Left) : 0ft 0.0m ~ 5ft 1.5m
• CEN (Center) : 0ft 0.0m ~ 5ft 1.5m
• F.R (Front-Right) : 0ft 0.0m ~ 5ft 1.5m
• S.R (Rear-Right) : 0ft 0.0m ~ 15ft 4.5m
• S.B (Rear Center): 0ft 0.0m ~ 15ft 4.5m
• S.L (Rear-Left): 0ft 0.0m ~ 15ft 4.5m
To Exit Setup Mode
• Wait for about 5 seconds or press the SPEAKER DISTANCE button of remote control
to select DISTANCE OFF.
2019
√
Press and hold SURROUND button for about 5 seconds
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 2 times.
• “DISTANCE SETUP” appears on the display.
Press SURROUND button to select the speaker you want.
• Each time you press this button, F.L ➝CEN ➝F.R ➝S.R ➝S.B ➝S.L ➝S.W
will be selected in turn.
Press SELECT( ) button to set the speaker distance.
• For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to
listening position between 0.0~1.5m at the interval of 0.3m.
• For S.R, S.B, S.L Speaker, you can set the distance from the speaker to listening
position between 0.0~4.5m at the interval of 0.3m.
Repeat the steps 3 and 4 to set the speaker distance.
Setting Speaker Distance
To Exit Setup Mode
• Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit. “SETUP MODE
OFF” appears on the display and exit Setup Mode.
• If the listening position is beyond the range of speaker
distance setup when you place the speaker, set the
speaker distance to the maximum.
REMOTE CONTROL
1
2
3
MAIN UNIT
1
2
4
5
3
,
OPERATION

Setting DRC
(Dynamic Range Compression)
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
2221
Test Tone
Use test tine to check speaker connection status or defect of speaker or adjust the level.
Press TEST TONE button.
• Test signal will be automatically output as follows; F.L ➝CEN ➝F.R ➝S.R
➝S.B ➝S.L ➝S.W.
• During test tone output, press …† button to adjust the speaker output level
from -10 to +10 dB by 1 step.
To Stop Test Tone
• Press TEST TONE button again.
√
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 3 times.
• “DRC SETUP” appears on the display.
Press SURROUND button to set DRC. • Each time you press this
button, DRC : STD ➝DRC :
MIN ➝DRC : MAX will be
selected in turn.
To Exit Setup Mode
• Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit.
“SETUP MODE OFF” appears on the display and exits Setup Mode.
√
• You cannot use test tone in 5.1CH MULTI CH function.
• This function operates only in main unit.
• STD : Set DRC effect to standard.
• MAX : Set DRC effect to maximum.
• MIN : Set DRC effect to minimum.
Setting DRC
MAIN UNIT
1
2
3
Caution!
To Automatically Output Test Tone
REMOTE CONTROL
1
Caution!
OPERATION

• F.L (Front-Left) : -10 ~ +10dB
• CEN (Center) : -10 ~ +10dB
• F.R (Front-Right) : -10 ~ +10dB
• S.R (Rear-Right) : -10 ~ +10dB
• S.B (Rear Center): -10 ~ +10dB
• S.L (Rear-Left): -10 ~ +10dB
• S.W (Subwoofer): -10 ~ +10dB 2423
Test Tone
Use test tone to check speaker connection status or defect of speaker or adjust the level.
Test Tone Output
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 5 times.
• “TEST-T MANU” appears in the display.
Press SURROUND button.
• Each time you press this button, F.L ➝CEN ➝F.R ➝S.R ➝S.B ➝S.L ➝S.W
will be selected in turn.
Press SELECT( )button to set the test tone as you want.
• You can adjust the speaker output level from -10 to +10dB by 1 step.
√
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 4 times.
• “TEST-T AUTO” appears in the display.
Press SURROUND button.
• Test signal will be automatically output as follows; F.L ➝CEN ➝F.R ➝S.R ➝S.B
➝S.L ➝S.W .
• During test signal output, press SELECT ( ) button to adjust the speaker output
level from -10 to +10 dB by 1 step.
√
• You cannot use test tone in 5.1CH MULTI CH function.
To Automatically Output Test Tone To Manually Output Test Tone
MAIN UNIT
1
2
3
MAIN UNIT
1
2
4
3
To Stop Test Tone
Method 1) Press INPUT button 2 times.
• “TEST-T OFF” appears on the display and test tone stops.
Method 2) Turn VOLUME CONTROL.
• “SETUP MODE OFF” appears on the display and test tone stops.
To Stop Test Tone
Method 1) Press INPUT button 1 time.
• “TEST-T OFF” appears on the display and test signal stops.
Method 2) Turn VOLUME CONTROL.
• “SETUP MODE OFF” appears on the display and test tone stops.
Caution!
,
,
OPERATION

Setting Speaker Level
You can set the balance and level of speakers
Press SPK LEVEL button to select the speaker you want.
• Each time you press this button, F.L ➝CEN ➝F.R ➝S.R ➝S.B ➝S.L ➝S.W ➝
SPK LEVEL OFF will be selected in turn.
Press …† button to set the speaker level you want.
• You can adjust it from -10 to +10dB by 1 step.
The sound gets smaller at -10dB and louder at +10dB.
Default setting value is 00dB.
Repeat the steps 1 and 2 to set it.
• F.L (Front-Left) : -10 ~ +10dB
• CEN (Center) : -10 ~ +10dB
• F.R (Front-Right) : -10 ~ +10dB
• S.R (Rear-Right) : -10 ~ +10dB
• S.B (Rear Center): -10 ~ +10dB
• S.L (Rear-Left): -10 ~ +10dB
• S.W (Subwoofer): -10 ~ +10dB
To Exit Setup Mode
• Wait for about 5 seconds or press SPK LEVEL button of remote control to select SPK
LEVEL OFF. To Exit Setup Mode
• Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. “SETUP
MODE OFF” appears on the display and exits Setup Menu.
2625
√
Press and hold SURROUND for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 7 times.
• “LEVEL SETUP” appears on the display.
Press SURROUND button.
• Each time you press this button, F.L ➝CEN ➝F.R ➝S.R ➝S.B ➝S.L ➝S.W
will be selected in turn.
Press SELECT( ) button to set to the speaker level you
want.
• You can adjust it from -10 to +10dB by 1 step.
• The sound gets smaller at -10dB and louder at +10dB.
• Default setting value is 00dB
Repeat the steps 3 and 4 to set it.
Setting Speaker Level
Remote Control
Remote Control
1
2
3
1
2
4
5
3
,
OPERATION

Dolby Pro Logic llx Mode
You can experience surround sound regardless of type of stereo mix by making existing Dolby Surround mix
sound similar to discrete 5.1 Channel Surround.
Press MODE button.
• Each time you press this button, MUSIC ➝ CINEMA ➝ MATRIX ➝ GAME ➝
PROLOGIC will be selected in turn.
• MUSIC : Provide 5.1 Channel Surround sound to digital, analog
or existing stereo source such as CD, TAPE, FM, TV and Stereo
VC.
• CINEMA : Provide 5.1 Channel Surround sound to sound track of
stereo movie encoded as Dolby Surround.
• MATRIX : You can feel 5.1 Channel Surround sound enjoying the
space of sound.
• GAME : When you play game, you can enjoy game with sound
effect as if you are at actual site.
• PROLOGIC : Decode(3/1 Surround) the sound track of stereo
music encoded as Dolby Surround to Dolby Pro Logic.
2827
Press SURROUND button briefly to select “DPL llx” Mode.
• Each time you press this button, DPL ll x ➝NEO:6 ➝SFE ➝STEREO will be
selected in turn.
Press SELECT( ) button.
• Each time you press SELECT ( ) button, MUSIC ➝CINEMA ➝MATRIX ➝
GAME ➝PROLOGIC will be selected in turn.
• Each time you press SELECT ( ) button, PROLOGIC ➝GAME ➝MATRIX
➝CINEMA ➝MUSIC will be selected in turn.
Dolby Pro Logic ll x Mode
• You cannot use Dolby Pro Logic ll x Mode for multi channel
signal encoded as Dolby Digital and DTS.
• You cannot use Dolby Pro Logic ll x Mode in 5.1 multi-
channel function.
• Pro Logic works only for PCM audio signals with sampling
frequency of 32KHz, 44KHz or 48KHz.
• Sound will not be output from rear center speaker if PCM
audio signal is not stereo but mono.
• Sound will be output from some speaker only if you
connect the external component only to Audio Input
connector (or R) of the main unit.
To Exit Setup Mode
• Wait for about 5 seconds.
To Exit Setup Mode
• Wait for about 5 seconds.
REMOTE CONTROL
1
MAIN UNIT
Caution!
1
2
,
OPERATION

Dolby Pro Logic llx Effect
This function works only in Dolby PRO LOGIC IIX MUSIC Mode.
Press MODE button to select ‘MUSIC’ Mode.
Press EFFECT button.
• Each time you press this button, C-WIDTH ➝DIMENSION ➝PANORAMA will be
selected in turn.
Press …† button to select Dolby Pro Logic IIx effect you want.
• C-WIDTH: You can set from 0 to 7.
• DIMENSION: You can set from 0 to 7.
• PANORAMA: You can Set it ON or OFF.
Repeat the steps 2 and 3 to set the Dolby Pro Logic IIx effect.
• C-WIDTH : Sound will be output from center speaker only. Front-left
and front-right speaker give sound field effect only. In addition, sounds
are output in different volumes from Front-Left, Front-Right Speaker and
Center Speaker.
• DIMENSION : Adjust the sound balance if the sound is unbalanced to
front or rear speaker.
• PANORAMA : Give the effect expanding and covering the sound from
front-left and front-right Speaker to both walls.
To Exit Setup Mode
• Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. “SETUP
MODE OFF” appears on the display and exits Setup Mode.
3029
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.Press
INPUT button 8 times.
• “DPL ll x MODE”appears on the display.
Press SURROUND button.
• Each time you press this button, DIMENSION ➝PANORAMA ➝C-WIDTH will
be selected in turn.
Press SELECT( ) button to select Dolby Pro Logic llx
effect you want.
Repeat the steps 3 and 4 to set Dolby Pro Logic llx effect.
Dolby Pro Logic llx Effect
To Exit Setup Mode
• Wait for about 5 seconds .
REMOTE CONTROL
1
2
4
3
MAIN UNIT
1
2
4
5
3
,
OPERATION

NEO:6 Mode
You can play back 2 channel sound in 6.1 channel of 360 degree surround when enjoying music or movie.
Press NEO:6 MODE button.
• Each time you press this button, MUSIC ➝CINEMA will be selected in turn.
3231
Press SURROUND button briefly to select “NEO:6” Mode.
• Each time you press this button, DPL ll x ➝NEO:6 ➝SFE ➝STEREO will be
selected in turn.
Press SELECT( ) button.
• Each time you press this button, MUSIC ➝CINEMA will be selected in turn.
This mode decodes 2 channel signals to high precision digital matrix
decoder.
DTS NEO:6 decoder discretes 2 channel sound to Discrete 6.1
channel sound.
• MUSIC : NEO:6 MUSIC Mode is used as optimized to music
according to played signal.
• CINEMA : NEO:6 CINEMA Mode is used as optimized to movie
according to played signal.
NEO : 6 Mode
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 9 times.
• “NEO:6 MODE” appears on the display.
Press SURROUND button.
• “CEN-IMG” appears on the display.
Press SELECT( ) button to set the sound image you want.
• You can set the sound image from 0 to 5.
•
NEO:6 Mode can be used in multi channel signal
encoded to Dolby Digital or DTS.
• Pro Logic works only for PCM audio signals with sampling
frequency of 32KHz, 44KHz or 48KHz..
• You can use this function to set the sound image of Center
Speaker only in the main unit.
To Exit Setup Mode
• Wait for about 5 seconds. To Exit Setup Mode
• Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. ‘SETUP MODE OFF’ appears
on the display and exits Setup Mode.
If TV (or screen) is installed high, you can feel the balance of sound and image by
raising the sound image of Center Speaker.
REMOTE CONTROL
1
Caution!
MAIN UNIT
1
1
2
3
4
2
To Set Sound Image of Center Speaker
Caution!
,
,
OPERATION

SFE Mode
Refer to the unique sound existing at specific place and you can feel live sound as if you are listening at
actual site.
Press SEF MODE button.
• Each time you press this button, LIVE ➝ROCK ➝CLASSIC ➝JAZZ ➝MIDNIGHT
➝HALL ➝CINEMA ➝CHURCH will be selected in turn.
3433
Press SURROUND button briefly to select ‘SFE’ Mode. Each
time you press this button, DPL II x ➝NEO:6 ➝SFE ➝STEREO will be
selected in turn.
Press SELECT( ) button.
• Each time you press Select ( ) button, LIVE ➝ROCK ➝CLASSIC ➝JAZZ
➝MIDNIGHT ➝HALL ➝CINEMA ➝CHURCH will be selected in turn
• Each time you press Select ( ) button, CHURCH ➝CINEMA ➝HALL ➝
MIDNIGHT ➝JAZZ ➝CLASSIC ➝ROCK ➝LIVE will be selected in turn.
• LIVE, ROCK, CLASSIC, JAZZ : Select the genre suitable for the
music among Live, Rock, Classic and Jazz to listen to music.
• MIDNIGHT : Emphasize bass when you listen to music at midnight.
• HALL : Clear music as if you are listening at concert hall.
• CINEMA : Enjoy sound as if you are in cinema.
• CHURCH : Enjoy magnificent sound as if you are listening at
church.
SFE Mode
To Exit Setup Mode
• Wait for about 5 seconds.
To Exit Setup Mode
• Wait for about 5 seconds.
REMOTE CONTROL
1
MAIN UNIT
1
2
,
OPERATION

EX/ES Mode
This mode enable you to listen 6.1 channel surround to the source encoded to Dolby Digital-EX, DTS-ES such as DVD.
This function works when Dolby Digital 5.1 channel source is inputted, and does not work when LPCM and Dolby Digital
2 channel source are entered.
Press EX/ES button.
• Each time you press this button, EX/ES AUTO ➝EX/ES ON ➝EX/ES OFF
will be selected in turn.
3635
Press and hold SURROUND button for about 5 seconds.
• “SETUP MODE” appears on the display and enters into Setup Mode.
Press INPUT button 10 times.
• “EX/ES SETUP” appears on the display.
Press SURROUND button.
• Each time you press this button, EX/ES : AUTO ➝EX/ES : ON ➝EX/ES :
OFF will be selected in turn.
• AUTO : 7.1 channel(or 6.1 channel) sound will be played back to
7.1 channel(or 6.1 channel) and 5.1 channel sound will be
automatically converted to and output as 5.1 channel.
• ON : 5.1 channel sound will be converted to and output as 7.1
channel (or 6.1 channel).
• OFF : 7.1 channel (or 6.1 channel) sound will be converted to and
output as 5.1 channel.
EX/ES Mode
Movie sound track encoded with Dolby Digital EX can play back
the rear center channel added during program mixing. Rear
center channel provides fine image, in-depth and realistic
feeling.
Dolby Digital - EX
• You cannot use Dolby Digital-EX in the system without rear
center speaker.
• You need to set it to EX/ES Mode when playing back disk
encoded to Dolby Digital-EX in 6.1 channel.
• Some disks encoded with Dolby Digital-EX do not contain
identification signal. In this case, set EX/ES to ON.
Rear center channel is added to DTS 5.1 channel, improving the
sense of direction and space for sound. Since DTS-ES decoder
is built-in in the main unit, you can play back the disk encoded
with DTS-ES Discrete and DTS-ES Matrix. DTS-ES Discrete 6.1
can record the sound of all channels including rear center
channel digitally and play back the recorded sound as they are.
DTS-ES (Discrete 6.1, Matrix 6.1)
• You cannot use DTS-ES in the system without rear center
speaker.
To Exit Setup Mode
• Wait for about 5 seconds or turn VOLUME CONTROL of the main unit. ‘SETUP
MODE OFF’ appears on the display and exits Setup Mode.
To Exit Setup Mode
• Wait for about 5 seconds or press EX/ES button of the remote control to select EX/ES
: OFF.
REMOTE CONTROL
MAIN UNIT
Caution!
Caution!
Method
1
2
3
OPERATION

3837
Stereo Mode
You can select this mode when you listen to the sound at Front-Left speaker, Front-Right speaker and
subwoofer.
• 96KHz PCM is not played back in Stereo Mode.
• When PCM and Analog Stereo signal are input,
left/right channel is played back in Stereo Mode. L/R : Front Speaker (Left/Right) C: Center Speaker SL/SR : Rear Speaker (Left/Right) S: Rear Center Speaker SW : Subwoofer
For Surround Mode and Input Signal
•
2 channel Dolby Digital signal has Dolby Digital Pro Logic. Speaker Setup is set to LARGE, SMALL, or YES.
• If there is no surround signal in DVD disk, sound will not output from rear-left speaker, rear-right speaker, center speaker, and
subwoofer.
Dolby D Surr. EX Dolby Digital 5.1 OOO -ODIGITAL L, C, R, SL, SR, S, SW
Dolby D (5.1ch) Dolby Digital 5.1 OOO -ODIGITAL L, C, R, SL, SR, SW
Dolby D (2ch) Pro Logic II x OOO OO DIGITAL L, R
Dolby D (2ch Surr) Pro Logic II x OOO OO DIGITAL L, R, S
L.PCM (Audio) Pro Logic II x OOO OO L.PCM L, R
Analog Pro Logic II x OOO OO ANALOG -
DTS-ES DTS 5.1 OOO OO dts, ES L, C, R, SL, SR, S, SW
DTS 96/24 DTS 96/24 OOO OO DTS 96/24 L, C, R, SL, SR, SW
DTS (5.1) DTS 5.1 OOO -O dts L, C, R, SL, SR, SW
L.PCM (Audio) Neo:6 OOO O- L.PCM L, R
Analog Neo:6 OOO O- ANALOG -
Dolby D (2ch) Neo:6 OOO O- DIGITAL L, R
Dolby D (2ch Surr) Neo:6 OOO O- DIGITAL L, R, S
Dolby Surr. EX SFE ----- DIGITAL L, C, R, SL, SR, S, SW
Dolby D (5.1ch) SFE ----- DIGITAL L, C, R, SL, SR, SW
Dolby D (2ch) SFE OOO OO DIGITAL L, R
Dolby D (2ch Surr) SFE OOO OO DIGITAL L, R, S
DTS-ES SFE ----- dts, ES L, C, R, SL, SR, S, SW
DTS (5.1ch) SFE ----- dts L, C, R, SL, SR, SW
L.PCM (Audio) SFE OOO OO L.PCM L, R
Analog SFE OOO OO ANALOG -
Dolby D Surr. EX Dolby Digital EX OOO OO DIGITAL L, C, R, SL, SR, S, SW
Dolby D (5.1ch) Dolby Digital EX OOO OO DIGITAL L, C, R, SL, SR, SW
DTS-ES DTS-ES OOO OO dts, ES L, C, R, SL, SR, S, SW
DTS (5.1ch) DTS-ES OOO OO dts L, C, R, SL, SR, SW
Dolby Surr. EX Stereo O-- -ODIGITAL L, C, R, SL, SR, S, SW
Dolby D (5.1ch) Stereo O-- -ODIGITAL L, C, R, SL, SR, SW
Dolby D (2ch) Stereo O-- --DIGITAL L, R,
Dolby D (2ch Surr) Stereo O-- --DIGITAL L, R, S
DTS-ES Stereo O-- -Odts, ES L, C, R, SL, SR, S, SW
DTS 96/24 Stereo O-- -Odts 96/24 L, C, R, SL, SR, SW
DTS (5.1ch) Stereo O-- -Odts L, C, R, SL, SR, SW
L.PCM (Audio) Stereo O-- --L.PCM L, R
L.PCM 96KHz Stereo O-- --L.PCM L, R
Analog Stereo O-- --ANALOG -
Surround Mode Input Signal Decoding
Output Channel
L/R C SL
SR SB SubW
Display Information
Display Signal Format Channel Status
EX/ES
DOLBY
(MUSIC,
CINEMA,
MATRIX,
GAME,
PROLOGIC)
NEO:6
(MUSIC,
CINEMA)
STEREO
SFE
Press STEREO button. • “STEREO” appears in the
display and Stereo Mode is
selected.
Press SURROUND button briefly to select
‘STEREO’.
• Each time you press this button, DPL ll x ➝NEO:6 ➝SFE ➝
STEREO will be selected in turn.
To Exit Setup Mode
• Wait for about 5 seconds. To Exit Setup Mode
• Wait for about 5 seconds.
REMOTE CONTROL MAIN UNIT
Caution!
Caution!
OPERATION