Samsung SND-7080F User manual

NETWORK CAMERA
Quick Guide SND-7080F
English
PT01-000156A-SND-7080FN-QG_ENGLI1 1 2011-03-24 오후 6:51:48

2_ English2
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance Item Name Quantity Description
User Manual,
Installer S/W DVD,
CMS S/W DVD
2
Quick Guide 1
Iron Screw 3 Used for fixing to an iron plate
Cable for the testing
monitor 1Used to test the camera connection to a portable display device
Template 1 Product installation guide
Tapping Screw 1 Used to fix the safety bracket
Bracket Safety 1 Safety Bracket
PT01-000156A-SND-7080FN-QG_ENGLI2 2 2011-03-24 오후 6:51:48

English
English _3
AT A GLANCE
Appearance
Item Description
a
Top cover Case cover used to protect the lens and the main unit.
b
Camera Case Covers the lens and camera body.
c
Power Port Used to plug the power cable.
d
Alarm In /
Out terminals
ARM-IN BLUE : Used to connect the alarm input signal.
ARM-OUT WHITE : Used to connect the alarm output signal.
A-COM GRAY : Common port where the alarm output signal is
connected.
GND YELLOW : Used for earth-grounding.
e
Network Port Used to connect a PoE or LAN cable.
f
Video Out Port Analog video output port. (for installation)
g
Audio In Jack Used to connect to a microphone.
h
Audio Out Jack Used to connect to speakers.
8
PT01-000156A-SND-7080FN-QG_ENGLI3 3 2011-03-24 오후 6:51:49

4_ English4
Inside
Item Description
a
Monitor Out Using the test monitor cable, you can connect to a mobile display for camera
test.
b
Reset Button
Resets the camera settings to the default. Press and hold it for about 5
seconds to turn off the system indicator and restart the system.
J
If you reset the camera, the network settings will be adjusted so that
DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can
connect to the network.
c
SD Memory Card
Compartment Compartment for the SD memory card.
PT01-000156A-SND-7080FN-QG_ENGLI4 4 2011-03-24 오후 6:51:49

English
English _5
INSTALLATION
Precautions before installation
Ensure you read out the following instructions before installing the camera:
Select an installation site (ceiling or wall) that can endure at least 5 times of the
camera weight.
Stuck-in or peeled-off cables can cause damage to the product or a fire.
For safety purposes, keep anyone else away from the installation site. And put aside
personal belongings from the site, just in case.
Disassembling
Take the camera body with one hand and take the
top cover with the other hand. Then, turn the cover
counter clockwise to remove it.
Installation
Use the provided template to drill one hole for
the camera, and one for the screw (5 mm in
diameter, at least 35 mm in depth), and insert
the plastic anchor (HUR 5) to the end of the
screw hole.
Connect and arrange the necessary cables
lest that they should be damaged or twisted
while installing the camera.
Insert the camera body into the hole so that it
fits to the camera hole, and fix the body using
the ASSY tapping screws (TH M4xL30). (x3)
Refer to “Adjusting the monitoring direction for the camera” to adjust the lens in a
desired direction.
Close the top cover.
Fit the top cover into the fixing tips of the camera body and turn the cover clockwise.



1.
1.
2.
3.
4.
5.

Top cover
Camera Body
PT01-000156A-SND-7080FN-QG_ENGLI5 5 2011-03-24 오후 6:51:49

6_ English6
Adjusting the monitoring direction for the camera
Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called
Tilt, and turning the lens on its axis is called Rotate.
The effective range of pan is a total of 355 degrees.
The effective range of rotation is a total of 355 degrees.
The effective range of tilt is a total of 90 degrees.
In some angles, the top cover may cause cutting some part of the monitoring object.
Do not rotate the focus/zoom lens by force after removing the cover front.
Otherwise, it may cause an incorrect focus due to a motor failure.
Methods of adjustment
After installing the camera, adjust the panning angle in consideration of the
monitoring direction.
When tilting the camera, you should adjust the horizontal angle lest that the image
be displayed reversely.
Adjust the rotation angle to correct the image display position (up/down/left/right).
Rotating means rotation on the basis of the rear lens unit.
Adjust the tilt angle so that the camera faces toward the monitoring object.
❖
-
-
-
J

❖
1.
2.

3.
Panning
Tilting
Lens rotation
Cover Front
PT01-000156A-SND-7080FN-QG_ENGLI6 6 2011-03-24 오후 6:51:49

English
English _7
CONNECTING WITH OTHER DEVICE
Connecting to the monitor
Connect the video out port of the camera to the video input port of the monitor.
In the initial installation of the camera, you can connect the camera to the monitor for checking
the connection status.
You can set the video output type to either NTSC or PAL.
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
If PoE and DC 12V are both applied, this camera will get supplied with power from PoE.
Please make sure the monitor and camera are turned off when connecting them.
M

J


Monitor
Power
Ethernet
Monitor Out
PT01-000156A-SND-7080FN-QG_ENGLI7 7 2011-03-24 오후 6:51:50

8_ English8
Connecting to Audio Input/Output
Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT
port of the amplifier that the microphone is connected to.
Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
Check the specifications for audio input.
Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
Full duplex Audio
Audio in
Used for mono signal line input (Max.2.4 Vpp)
Audio out
Used for mono signal line output (Max.2.4 Vpp)
Line out impedance
600Ω
1.
2.
3.





PC
Network
Speaker
Microphone
Amp
Amp
Microphone
Microphone
Speaker
PT01-000156A-SND-7080FN-QG_ENGLI8 8 2011-03-24 오후 6:51:50

English
English _9
IP SETUP
Manual Network Setup
Run <IP Installer_vX.XX.exe> to display the camera search list.
At the initial startup, both [Auto Set] and [Manual Set] will be grayed out.
For cameras found with the IPv6 setting, these buttons will be grayed out as the cameras do not
support this function.
Select a camera in the search list.
Find the MAC (Ethernet) address
labeled on the rear of the camera.
Both the [Auto Set] and [Manual Set]
buttons will be activated.
Click [Manual Set].
The Manual Setting dialog appears.
The default values of <IP Address>,
<Subnet Mask>, <Gateway>, <HTTP Port> and <VNP Port> of the camera will
be displayed.
In the <Address> pane, provide the
necessary information.
MAC (Ethernet) Address : The MAC
(Ethernet) address of the applicable
camera will be set automatically so
you don't need to input it manually.
You can configure the static IP settings
only if the DHCP checkbox is unchecked.
In the <Port> pane, provide necessary information.
HTTP Port : Used to access the camera using the Internet browser, defaulted to
80. Use the spin button to change the HTTP Port value.
VNP Port : Used to control the video signal transfer, defaulted to 4520.
Enter the password.
This is the login password for the “admin” user who accesses the camera.
The default password is “4321”.
Click [OK].
Manual network setup will be completed.
M
1.
2.
3.

M
4.


5.
6.
PT01-000156A-SND-7080FN-QG_ENGLI9 9 2011-03-24 오후 6:51:50

10_ English10
USING THE LIVE SCREEN
Item Description
a
Monitoring Move to the monitoring screen.
b
Playback Switch to the monitoring screen that plays recording data in the SD memory.
c
Setup Move to the Setup screen.
d
Viewer Screen Displays the Live video on the screen.
e
Alarm Output Activate the Alarm Out port.
f
Audio Display the audio Listen and Talk toggle button on the screen.
g
Hide the alarm
indicator Hides the alarm indicator near the border of the viewer screen.
PT01-000156A-SND-7080FN-QG_ENGLI10 10 2011-03-24 오후 6:51:50