Samsung SNP-6321H User manual

NETWORK CAMERA
Network Setup Guide

CHECKING NETWORK
CONFIGURATION
3
3Selecting the network type
NETWORK CONFIGURATION
11
11 Configure the network on the PC used for IP
configuration
12 Launching IP Installer
19 Configuring IP installer values
23 How to configure port forwarding
28 Login
32 Installing the program needed to launch the
webviewer after connecting to network camera
SETUP SCREEN
38
38 Web viewer-Network Setup
47 Web viewer-Password Setup
CONTENTS

English _3
●
CHECKING NETWORK CONFIGURATION
checking network configuration
Configure the network after checking the following.
1. Check whether to use a DDNS server.
- Check whether to use a DDNS for remote monitoring from outside, or to configure the system in the form of
a local network for monitoring only inside the local network.
2. Check whether to use a static IP or dynamic IP.
3. Before installation, check the number and locations of network cameras and the location of the monitoring PC.
4. Check the network devices to be connected to a network camera, such as IP router/hub.
5. Check the port forwarding, ports and protocol required for establishing a camera connection path.
SELECTING THE NETWORK TYPE
Select the type of network that you want to configure based on the following information.
If DDNS server is not used:
As shown in the image below, if the monitoring PC and network camera are connected to the same router, they
will have the same IP range.
Install the IP installer on the local monitoring PC and use the PC for IP configuration.
EX1)
WAN
Modem
Router
Local monitoring PC Network camera1 Network camera n
...
EX2)
WAN
Modem
Router
Local monitoring PC Network camera 1 Network camera n Hub
...
...
Network camera 1 Network camera n

checking network configuration
4_ Checking network configuration
EX3)
WAN
Modem
Router
Hub
Local monitoring PC Network camera 1 Network camera n
...
EX4)
WAN
Modem
Router
Hub
Local monitoring PC
Network camera 1 Network camera n
...

English _5
●
CHECKING NETWORK CONFIGURATION
As shown in the image below, if the monitoring PC and network camera are connected to different routers, the
network camera cannot be configured, even if the IP installer is installed in the local monitoring PC.
In this case, connect the configuration PC or notebook to the router (1) to set up the network camera.
EX5)
WAN
Modem
Router(1)Configuration PC
Router(2)
Local monitoring PC
Network camera nNetwork camera 1 ...
M
Remove the PC or laptop for IP configuration after the configuration.

checking network configuration
6_ Checking network configuration
If DDNS server is used:
As shown in the image below, if the monitoring PC and network camera are connected to the same router, they
will have the same IP range.
Install the IP Installer on the local PC and use the PC for IP configuration.
EX1)
Internet
Modem
DDNS
Server
External remote
monitoring PC
Router
Local monitoring PC Network camera n
...
Network camera1
EX2)
Modem
Router
Local monitoring PC Network camera 1 Network camera n Hub
...
...
Network camera 5 Network camera n
DDNS
Server
External remote
monitoring PC
Internet

English _7
●
CHECKING NETWORK CONFIGURATION
EX3)
Internet
Modem
Router
Hub
Local monitoring PC Network camera1 Network camera n
...
DDNS
Server
External remote
monitoring PC
EX4)
Internet
Modem
Router
Hub
Local monitoring PC
Network camera1 Network camera n
...
DDNS
Server
External remote
monitoring PC

checking network configuration
8_ Checking network configuration
As shown in the image below, if the monitoring PC and network camera are connected to different routers, the
network camera cannot be configured, even if the IP installer is installed in the local monitoring PC.
Connect another PC or laptop for IP configuration to router (1) and configure the network camera.
EX5)
Internet
Modem
Router(1)Configuration PC
Router(2)
Local monitoring PC
Network camera nNetwork camera 1 ...
DDNS
Server
External remote
monitoring PC
As shown in the image below, if the monitoring PC and the network camera are connected to the DSL/Cable/
PPPoE modem directly without connecting to the local network, connect another PC or laptop and use the PC
to configure a network camera IP.
EX6)
Internet
DSL/Cable/PPPoE
Modem
DDNS
Server
External remote
monitoring PC
Configuration PC
Network camera
M
Remove the PC or laptop for IP configuration after the configuration.

English _9
●
CHECKING NETWORK CONFIGURATION
If the network environment makes it difficult to configure an IP for the
network camera in a typical way:
As shown in the image below, if two or more routers are located at the upper layer of the network camera, it will
generally be impossible to configure the network camera.
In this environment, it is necessary to convert the router (2) into a general hub equipment (by turning off the
DHCP function in the Router Setup menu so that the IP addresses of the router (1) and (2) do not crash with
each other to make the router (2) operates as it were a general hub equipment) or double port forwarding of
the routers (1) and (2).
J
It is difficult to change and configure the network, so it is recommended to ask the network administrator of the site to
replace router (2) with a general hub, and connect the network camera.
EX1)
Internet
Modem
DDNS
Server
External remote
monitoring PC
Router(1)
Router(2)
Local monitoring PC Network camera 1 Network camera n
...
EX2)
Internet
Modem
DDNS
Server
External remote
monitoring PC
Router(1)
Router(2)
Local monitoring PC Network camera 1 Network camera n
...

checking network configuration
10_ Checking network configuration
EX3)
WAN
Modem
Router(1)
Router(2)
Network camera 1 Network camera n
...
Local monitoring PC
EX4)
WAN
Modem
Router(1)
Router(2)
Local monitoring PC Network camera 1 Network camera n
...

English _11
● NETWORK CONFIGURATION
network configuration
How to check the IP range of the router connected to the network camera.
1. Click Start Run Windows in the Windows screen and enter “cmd”.
2. Type “ipconfig” in the command window.
Information about the IP of the PC for IP configuration connected to the router will be displayed.
M
If the same gateway and subnet mask are used, the IP range is the same because the network camera is
connected to the same router.
Router
Network camera 1 Network camera n
...
IP Installer of PC for
IP configuration
CONFIGURE THE NETWORK ON THE PC USED FOR IP
CONFIGURATION
Connect a PC to configure IP
To launch the IP installer program for IP configuration, connect the PC to the same router in order to have the
same IP range as the network camera.
M
If there is a local PC within the same IP range, launch the IP installer on the local PC to configure the network.
If there is no local PC within the same IP range, connect another PC to configure an IP.
Router(1)
Router(2) Network camera 1 Network camera n
...
IP Installer of PC for
IP configuration

network configuration
12_ network configuration
How to configure the network environment of the PC used for IP
configuration
1. Open the network environment configuration menu of the
PC connected to the router.
2.
Path : Control panel Network and Sharing Center 
Change adapter settings Local Area Connection 
Properties Internet Protocol Version (TCP/IPv4) Properties
3. Select "Obtain an IP address automatically" and "Obtain
DNS server address automatically.”
M
If the IP range of the PC used for IP configuration is different
from that of the network camera, the camera will not be
detected, even if you click [Search].
LAUNCHING IP INSTALLER
What is IP Installer?
The IP Installer, launched on the PC for IP configuration, receives MAC address information transmitted from the
network devices with the IP range of the router, and detects network cameras.
If the IP configuring PC (on which the IP Installer is installed) and the network camera are connected to different
routers and their IP ranges are different, the IP Installer cannot detect network cameras.
EX1) In the following network structure, a MAC address of the network camera is not transmitted to outside
router (2), and a network camera is not detected on the IP Installer of the local PC.
Router(1)
Router(2)
IP Installer of PC for
IP configuration
Network camera 1 Network camera n
...
EX2) The IP configuring PC, on which the IP Installer is installed, must be located in the same IP range of the
router with the network camera in order to detect network cameras.
Router(1)
Router(2) Network camera 1 Network camera n
...
IP Installer of PC for
IP configuration

English _13
● NETWORK CONFIGURATION
If DDNS server is not used:
In the following case, launch the IP Installer on the local monitoring PC.
EX1)
WAN
Modem
Router
Local monitoring PC Network camera1 Network camera n
...
EX2)
WAN
Modem
Router
Local monitoring PC Network camera 1 Network camera n Hub
...
...
Network camera 1 Network camera n

network configuration
14_ network configuration
EX3)
WAN
Modem
Router
Hub
Local monitoring PC Network camera 1 Network camera n
...
EX4)
WAN
Modem
Router
Hub
Local monitoring PC
Network camera 1 Network camera n
...
In the following case, connect another configuring PC to router (1) and launch the IP Installer.
EX5)
WAN
Modem
Router(1)Configuration PC
Router(2)
Local monitoring PC
Network camera nNetwork camera 1 ...

English _15
● NETWORK CONFIGURATION
If DDNS server is used:
In the following case, launch the IP Installer on the local monitoring PC.
EX1)
Internet
Modem
DDNS
Server
External remote
monitoring PC
Router
Local monitoring PC Network camera n
...
Network camera1
EX2)
Modem
Router
Local monitoring PC Network camera 1 Network camera n Hub
...
...
Network camera 5 Network camera n
DDNS
Server
External remote
monitoring PC
Internet

network configuration
16_ network configuration
EX3)
Internet
Modem
Router
Hub
Local monitoring PC Network camera1 Network camera n
...
DDNS
Server
External remote
monitoring PC
EX4)
Internet
Modem
Router
Hub
Local monitoring PC
Network camera1 Network camera n
...
DDNS
Server
External remote
monitoring PC

English _17
● NETWORK CONFIGURATION
In the following case, connect another configuring PC to router (1) and launch the IP Installer.
EX5)
Internet
Modem
Router(1)Configuration PC
Router(2)
Local monitoring PC
Network camera nNetwork camera 1 ...
DDNS
Server
External remote
monitoring PC
In the following case, connect the configuring PC directly to the network camera and launch the IP Installer.
EX6)
Internet
DSL/Cable/PPPoE
Modem
DDNS
Server
External remote
monitoring PC
Configuration PC
Network camera

network configuration
18_ network configuration
Buttons used in IP Installer
Item Description
Device Name
Model name of the connected camera.
Click the column to sort the list by model name.
However, search will be stopped if clicked during the search.
bAlias This function is not currently implemented.
cMode Displays either <Static>, <Dynamic> or <PPPoE> for the current network connection status.
MAC(Ethernet)
Address
Ethernet address for the connected camera.
Click the column to sort the list by Ethernet address.
However, search will be stopped if clicked during the search.
IP Address
IP address.
Click the column to sort the list by IP address.
However, search will be stopped if clicked during the search.
Protocol
Network setting for the camera.
The factory default is “IPv4”.
Cameras with the IPv6 setting will be displayed “IPv6”.
URL DDNS URL address enabling access from the external Internet.
However, this will be replaced with the <IP Address> of the camera if DDNS registration has failed.
IPv4 Scans for cameras with the IPv4 setting.
IPv6 Scans for cameras with the IPv6 setting.
Activated in an IPv6 compliant environment only.
Search Scans for cameras that are currently connected to the network.
However, this button will be grayed out if neither IPv4 nor IPv6 is checked.
 b c    
     m

English _19
● NETWORK CONFIGURATION
Item Description
Auto Set The IP Installer automatically configures the network settings.
Manual Set You should configure the network settings manually.
mExit Exits the IP Installer program.
CONFIGURING IP INSTALLER VALUES
How to configure with a static IP
Notice for Setup with a Static IP
If assigning a static IP to the network camera: If the range of the assigned static IP is close to that of
network devices (such as PC and printer to which IP addresses are assigned), it may cause an IP
assignment error or an IP collision with other network devices after the router is turned off/on or reset. For
this reason, it is recommended to assign IP addresses that are not usually used in other network devices.
Ex) If network devices such as printer and PC use between 192.168.1.1 and 192.168.1.10 in the router:
The network camera should use between 192.168.1.101 and 192.168.1.200.
How to configure IP manually using [Manual Set]:
1. Launch the IP Installer on the PC for IP configuration.
2. Click the [Search] button. A list of network devices using IP
addresses located at the same router is displayed.
3. Check the MAC address information and select a device to
configure.
4. Click the [Manual Set] button. A window to configure an
address and port pops up.
5. Enter the IP range information assigned by the network
administrator or the IP range information (IP Address,
Subnet Mask, Gateway, HTTP Port, Device Port) that you
want to assign.
6. Type the password authentication number for camera
access and click the [OK] button. Configuration is now
complete.

network configuration
20_ network configuration
M
The password for camera access is identical to the “admin” login password.
Default value is “4321”.
 In the IP installer, you can use the initial password, “4321” to set IP Address, Subnet Mask, Gateway, HTTP Port,
Device Port, IP type. After changing the network interface, for better security, access the web viewer and change the
password.
 For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and
lowercase and special characters for your password.
 HTTP Port is used to connect to the camera using web browser.
Default value is “80”.
 Device Port is to control video transmission.
Default value is “4520”.
How to configure an IP address automatically using [Auto Set]:
1. Launch the IP Installer on the PC for IP configuration.
2. Click the [Search] button. A list of network devices using IP
addresses located at the same router is displayed.
3. Check the MAC address information and select a device to
configure.
4. Click on the [Auto Set] button.
[Auto Setting] window with IP Address, Subnet Mask and
Gateway entered pops up.
5. Type the password authentication number for camera
access and click the [OK] button. Configuration is now
complete.
M
The password for camera access is identical to the “admin”
login password.
Default value is “4321”.
 In the IP installer, you can use the initial password, “4321” to
set IP Address, Subnet Mask, Gateway, HTTP Port, Device Port,
IP type. After changing the network interface, for better security,
access the web viewer and change the password.
 For the security purposes, you are recommended to use a combination of numbers, alphabets uppercase and
lowercase and special characters for your password.
 Device Port is to control video transmission.
Default value is “4520”.