Samsung HW-NW700 User manual

HW-NW700
USER MANUAL

ENG - 2
SAFETY INFORMATION
SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that high voltage
is present inside. It is dangerous to
make any kind of contact with any
internal part of this product.
This symbol indicates that this product
has included important literature
concerning operation and maintenance.
Class II product : This symbol indicates
that it does not require a safety
connection to electrical earth (ground).
AC voltage : This symbol indicates that
the rated voltage marked with the
symbol is AC voltage.
DC voltage : This symbol indicates that
the rated voltage marked with the
symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to
consult the user manual for further
safety related information.
WARNING
•To reduce the risk of re or electric shock, do
not expose this appliance to rain or moisture.
CAUTION
•TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
•This apparatus shall always be connected to a
AC outlet with a protective grounding
connection.
•To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.
•Do not expose this apparatus to dripping or
splashing. Do not put objects lled with
liquids, such as vases on the apparatus.
•To turn this apparatus off completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.

ENG - 3
PRECAUTIONS
1. Ensure that the AC power supply in your
house complies with the power
requirements listed on the identication
sticker located on the bottom of your
product. Install your product horizontally, on
a suitable base (furniture), with enough
space around it for ventilation (7~10 cm).
Make sure the ventilation slots are not
covered. Do not place the unit on ampliers
or other equipment which may become hot.
This unit is designed for continuous use. To
fully turn off the unit, disconnect the AC plug
from the wall outlet. Unplug the unit if you
intend to leave it unused for a long period of
time.
2. During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or
other heat sources. This could lead to
overheating and cause the unit to
malfunction.
4. Protect the product from moisture (i.e.
vases), and excess heat (e.g. a replace) or
equipment creating strong magnetic or
electric elds. Unplug the power cable from
the AC wall socket if the unit malfunctions.
Your product is not intended for industrial
use. It is for personal use only. Condensation
may occur if your product has been stored in
cold temperatures. If transporting the unit
during the winter, wait approximately
2 hours until the unit has reached room
temperature before using.
5. The battery used with this product contains
chemicals that are harmful to the
environment. Do not dispose of the battery
in the general household trash. Do not
expose the battery to excess heat, direct
sunlight, or re. Do not short circuit,
disassemble, or overheat the battery.
Danger of explosion if the battery is replaced
incorrectly. Replace only with the same or
equivalent type.
ABOUT THIS MANUAL
The user manual has two parts: this simple paper
USER MANUAL and a detailed FULL MANUAL you
can download.
USER MANUAL
See this manual for safety instructions,
product installation, components,
connections, and product specications.
FULL MANUAL
You can access the FULL MANUAL on
Samsung’s on-line customer support centre by
scanning the QR code. To see the manual on
your PC or mobile device, download the
manual in document format from Samsung’s
website. (http://www.samsung.com/support)
Design, specications, and App screen are subject to
change without prior notice.

ENG - 4
CONTENTS
01 Checking the Components 6
Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 6
02 Product Overview 7
Front Panel / Bottom Panel of the Soundbar ------------------------- 7
Rear Panel of the Soundbar ------------------------- 7
03 Connecting the Soundbar 8
Connecting Electrical Power ------------------------- 8
04 Connecting to a TV 9
Connecting using an Optical Cable ------------------------- 9
Connecting Wirelessly ------------------------- 10
– Connecting a TV via Bluetooth ------------------------- 10
– Connecting via Wi-Fi ------------------------- 12
05 Connecting an External Device 14
Connecting using an Optical Cable ------------------------- 14
06 Connecting a Mobile Device 15
Connecting via Bluetooth ------------------------- 15
Connecting via Wi-Fi (Wireless Network) ------------------------- 16

ENG - 5
07 Using the Remote Control 17
How to Use the Remote Control ------------------------- 17
Adjusting the Soundbar volume with a TV remote control ------------------------- 20
08 Installing the Wall Mount 21
Installation Precautions ------------------------- 21
Wallmount Components ------------------------- 21
09 Software Update 25
10 Troubleshooting 26
11 Licence 27
12 Open Source Licence Notice 27
13 Important Notes About Service 27
14 SpecicationsandGuide 28
Specications ------------------------- 28

ENG - 6
01 CHECKING THE COMPONENTS
VOL BASS
SOUNDBAR
SOUND
MODE
PAIR
Soundbar Main Unit Remote Control /
Batteries
AC/DC Adapter Power Cord
x 3 x 3
(M5 x L50)
Wall Mount Guide Bracket-Wall Mount Anchor / Screw
x 2 x 2
(M3 x L10)
(Optionally)
x 1
Holder-Cable Cushion Pad Holder-Dongle Screw
•For more information about the power supply and power consumption, refer to the label attached
to the product. (Label : Bottom of the Soundbar Main Unit)
•For Soundbar wall mounting components, see page 21.
•To purchase additional components or optional cables, contact a Samsung Service Centre or
Samsung Customer Care.
•This Soundbar is for wall mounting only.
•Use the Holder-Dongle Screw to secure the Holder-Dongle when connecting the Soundbar to the
Wireless Rear Speaker Kit (SWA-9000S) or Wireless Subwoofer (SWA-W700) (Sold separately).
Please see the FULL MANUAL for details.
Inserting Batteries before using the Remote Control (AA batteries X 2)
Slide the battery cover in the direction of the arrow
until it is completely removed. Insert 2 AA batteries
(1.5V) oriented so that their polarity is correct. Slide
the battery cover back into position.

ENG - 7
02 PRODUCT OVERVIEW
Front Panel / Bottom Panel of the Soundbar
Display
Power Volume 󱂓
Bottom Panel
Position the product so that the SAMSUNG logo is located on the top.
Rear Panel of the Soundbar
DIGITAL AUDIO IN
(OPTICAL)
DC 23V
WIRELESS
ID SET
(WOOFER/REAR)
NETWORK
DIGITAL AUDIO IN
(OPTICAL)
DC 23V
WIRELESS
ID SET
(WOOFER/REAR)
NETWORK
󱂗 󱂘
󱂔
󱂕
󱂖
󱂓Source
Selects the source input mode. (D.IN / WIFI / BT)
•To turn on “BT PAIRING” mode, change the source to “BT” mode, and then press and
hold the button on the bottom panel for more than 5 seconds.
󱂔D.IN Connect to the digital (optical) output of an external device.
󱂕WIRELESS
Attach the wireless dongle that connects the Soundbar to surround speakers and a
subwoofer wirelessly. (The surround speaker, subwoofer, and wireless dongle are sold
separately.)
󱂖DC 23V Connect the AC/DC power adapter. (Power Supply In)
󱂗NETWORK Press to connect to a wireless network (Wi-Fi) via the SmartThings app.
󱂘ID SET Press to connect the Soundbar to surround speakers and a subwoofer wirelessly.
•Press and hold the Up button on the remote for 5 seconds to complete ID SET.

ENG - 8
03 CONNECTING THE SOUNDBAR
Connecting Electrical Power
Use the power components (1, 2) in the following order to connect the Soundbar to an electrical outlet:
1 Connect the power output cable to the power adapter, and then to the Soundbar.
2 Connect the power cord to a wall socket.
See the illustrations below.
•For more information about the required electrical power and power consumption, refer to the
label attached to the product. (Label : Bottom of the Soundbar Main Unit)
DIGITAL AUDIO IN
(OPTICAL)
DC 23V
WIRELESS
NETWORK
DC 23V
Rear of the Soundbar
Main Unit
1 AC/DC Adapter
2 Power Cord
Connecting
Electrical Power
•Make sure to rest the AC/DC
Adapter at on a table or the oor.
If you place the AC/DC Adapter so
that it is hanging with the AC cord
input facing upwards, water or
other foreign substances could
enter the Adapter and cause the
Adapter to malfunction.

ENG - 9
04 CONNECTING TO A TV
Hear TV sound from your Soundbar through wired or wireless connections.
•When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using
the TV’s remote control.
– This feature is supported by 2017 and later Samsung Smart TVs that support Bluetooth when
you connect the Soundbar to the TV using an optical cable.
– This function also allows you to use the TV menu to adjust the sound eld and various settings
as well as the volume and mute.
Connecting using an Optical Cable
When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on
your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on
the TV is changed, you will experience better sound quality. (The TV menu may use different words for
Dolby Digital and PCM depending on the TV manufacturer.)
DIGITAL AUDIO IN
(OPTICAL)
DC 23V
WIRELESS
OPTICAL OUT
Optical Cable
(not supplied)
Rear of the Soundbar
D.IN
󱂓
Bottom of the Soundbar
󱂔
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV
with a digital optical cable (not supplied).
2. Press the button on the bottom panel or on the remote control, and then select the “D.IN”
mode.

ENG - 10
Auto Power Link
Auto Power Link automatically turns on the Soundbar when the TV is turned on.
1. Connect the Soundbar and a TV with a digital optical cable (not supplied).
2. Press the Left button on the remote control (the blue spot in the illustration
to the right) for 5 seconds to turn Auto Power Link on or off.
•Auto Power Link is set to ON by default.
(To turn off this function, press the Left button on the remote for 5 seconds.)
•Depending on the connected device, Auto Power Link may not function.
•This function is only available in the “D.IN” mode.
Connecting Wirelessly
Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
•Only one TV can be connected at a time.
SOUND
MODE
PAIR
OR
Bottom of the Soundbar
The initial connection
1. Press the
VOL WOOFER
SOUND
MODE
PAIR
button on the remote control to enter the “BT PAIRING” mode.
(OR) a. Press the button on the bottom panel and then select “BT”.
“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device
connected to the Soundbar.
b. When “BT READY” appears, press and hold the button on the bottom panel of the
Soundbar for more than 5 seconds to display “BT PAIRING”.
2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
3. Select “[AV] Samsung Soundbar NWxxx” from the list on the TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” in the TV Bluetooth device list.
To connect the TV to the Soundbar, select the message, and then establish a connection.
•When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.
4. You can now hear TV sound from the Soundbar.

ENG - 11
If the device fails to connect
•If a previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar NWxxx”) appears in the
list, delete it.
•Then repeat steps 1 through 3.
Disconnecting the Soundbar from the TV
Press the button on the bottom panel or on the remote control and switch to any mode but “BT”.
•Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)
•To cancel the automatic Bluetooth connection between the Soundbar and TV, press the button
on the remote control for 5 seconds with the Soundbar in “BT READY” status. (Toggle On → Off)
What is the difference between BT READY and BT PAIRING?
•BT READY : In this mode, you can search for previously connected TVs or connect a previously
connected mobile device to the Soundbar.
•BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the
VOL WOOFER
SOUND
MODE
PAIR
button on
the remote control or press and hold the button on the Bottom of the Soundbar for more than
5 seconds while the Soundbar is in “BT” mode.)
NOTES
– If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
– In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
– The Soundbar automatically turns off after 5 minutes in the Ready state.
– The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
– If there is a strong electrical eld around the Soundbar.
– If several Bluetooth devices are simultaneously paired with the Soundbar.
– If the Bluetooth device is turned off, not in place, or malfunctions.
– Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.

ENG - 12
Connecting via Wi-Fi
Pre-connection Checklist
1. Conrm that your Samsung Smart TV was released after 2014. This function is compatible only
with Samsung Smart TVs released after 2014.
2. Make sure your Wireless router (Wi-Fi) is ready and working.
3. Make sure that the TV is connected to the Wireless router (your Wi-Fi network).
Bottom of the Soundbar
Step 1 : Connecting the Soundbar to Wi-Fi
1. Press the button on the Bottom of the Soundbar or on the remote control to select “WIFI”
mode.
•When using selected Samsung TVs (2016 ~ 2018 Samsung Smart TVs that support Bluetooth.)
– If you select “WIFI” mode when the TV is turned on, the TV screen displays a pop-up
window providing instructions on how to automatically connect the Soundbar to a wireless
router (Wi-Fi). Refer to instructions in the pop-up window of the TV.
Bottom of the Soundbar
WIFI
2. Connect your mobile device (smartphone, tablet, etc.) to the Wi-Fi network the TV is connected to.

ENG - 13
3. Install and launch the SmartThings app on your mobile device (smartphone, tablet, etc.).
SmartThings app
iOSAndroid
4. Follow the instructions in the app screen on the mobile device to connect the Soundbar to your
Wi-Fi network.
Step2:ConguringSettingsontheTV
•If the TV disconnects from your wireless network after you change the input source to the
Soundbar, use the TV menu to connect the TV to the network again.
For TVs released in 2018
Home ( ) Settings ( ) Sound Sound Output [AV] Samsung Soundbar NWxxx (Wi-Fi)
For TVs released in 2017
Home ( ) Settings ( ) Sound Sound Output [AV] Samsung Soundbar NWxxx (Wi-Fi)
For TVs released in 2016
Home ( ) Settings ( ) Sound Select Speaker [AV] Samsung Soundbar NWxxx (Wi-Fi)
For TVs released in 2015
Menu Sound Speaker List
For TVs released in 2014
Menu Sound Speaker Settings Multiroom Link - Settings
NOTES
– The TV and Soundbar must be connected to the same wireless network (Wi-Fi).
– If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi
connection between the TV and Soundbar. Contact your Internet service provider for details.
– If the 5GHz Wi-Fi connection is not smooth, use the 2.4GHz bandwidth.
– Because the menus may differ depending on the year of manufacture, refer to your TV manual.

ENG - 14
05 CONNECTING AN EXTERNAL DEVICE
Connect to an external device via a wired or wireless network to play the external device’s sound
through the Soundbar.
Connecting using an Optical Cable
Bottom of the Soundbar
󱂔
DIGITAL AUDIO IN
(OPTICAL)
DC 23V
WIRELESS
OPTICAL OUT
Optical Cable
(not supplied)
Rear of the Soundbar
D.IN
BD / DVD player / Set-top box /
Game console 󱂓
1. Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source
Device using a digital optical cable (not supplied).
2. Select “D.IN” mode by pressing the button on the bottom panel or on the remote control.

ENG - 15
06 CONNECTING A MOBILE DEVICE
Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.
•You cannot connect more than one Bluetooth device at a time.
SOUND
MODE
PAIR
OR
Bottom of the Soundbar
Bluetooth device
The initial connection
1. Press the
VOL WOOFER
SOUND
MODE
PAIR
button on the remote control to enter the “BT PAIRING” mode.
(OR) a. Press the button on the bottom panel and then select “BT”.
“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device
connected to the Soundbar.
b. When “BT READY” appears, press and hold the button on the bottom panel of the
Soundbar for more than 5 seconds to display “BT PAIRING”.
2. On your device, select “[AV] Samsung Soundbar NWxxx” from the list that appears.
•When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”
appears in the front display.
3. Play music les from the device, connected via Bluetooth, through the Soundbar.
If the device fails to connect
•If a previously connected Soundbar listing (e.g. “[AV] Samsung Soundbar NWxxx”) appears in the
list, delete it.
•Then repeat steps 1 and 2.
NOTE
– After you have connected the Soundbar to your mobile device the rst time, use the “BT READY”
mode to reconnect. See Page 11 for details.
For more information about Bluetooth connections, refer to “Connecting a TV via
Bluetooth” on pages 10~11.

ENG - 16
Connecting via Wi-Fi (Wireless Network)
•Connect a single Soundbar to Wi-Fi to access a variety of music streaming services and Internet
radio. Connect multiple Soundbars to Wi-Fi to use grouped playback or the stereo sound mode.
•To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the SmartThings app is
required.
Bottom of the Soundbar
Mobile device
The initial connection
1. Press the button on the Bottom of the Soundbar or on the remote control to select “WIFI”
mode.
Bottom of the Soundbar
WIFI
2. Install and launch the SmartThings app on your mobile device (e.g. smartphone or tablet).
SmartThings app
iOSAndroid
3. Follow the instructions in the app screen on the mobile device to connect the Soundbar to Wi-Fi.
NOTES
– Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit
(SWA-9000S) and Subwoofer (SWA-W700) to your Soundbar.
– The SWA-9000S and SWA-W700 are sold separately.
– To learn about using the SmartThings app and connecting to other devices (e.g. Amazon,
the SWA-9000S and SWA-W700), refer to the FULL MANUAL for your Soundbar on the Samsung
web site (www.samsung.com/support).

ENG - 17
07 USING THE REMOTE CONTROL
How to Use the Remote Control
VOL BASS
SOUNDBAR
SOUND
MODE
PAIR
󱂓
󱂔
󱂕
󱂖
󱂗
󱂙
󱂘
󱂚
󱂜
󱂛
󱂓
Power
VOL WOOFER
SOUND
MODE
PAIR
Turns the Soundbar on and off.
󱂔
VOL WOOFER
SOUND
MODE
PAIR
Source
Press to select a source connected to the
Soundbar.
󱂕
Mute
VOL WOOFER
SOUND
MODE
PAIR
Press the
VOL WOOFER
SOUND
MODE
PAIR
button to mute the sound.
Press it again to unmute the sound.
󱂖
SOUND MODE
VOL WOOFER
SOUND
MODE
PAIR
You can select the desired sound effect by
choosing STANDARD, SURROUND,or SMART.
󱂗
VOL WOOFER
SOUND
MODE
PAIR
Bluetooth
PAIR
Press the
VOL WOOFER
SOUND
MODE
PAIR
button. “BT PAIRING” appears in
the Soundbar’s display.
You can connect the Soundbar to a new
Bluetooth device in this mode by selecting the
Soundbar in the Bluetooth device's search list.

ENG - 18
󱂘
Play / Pause
(BT/Wi-Fi)
Press the button to pause a music le temporarily.
When you press the button again, the music le plays.
󱂙
VOL WOOFER
SOUND
MODE
PAIR
Up/Down/
Left/Right
Press the indicated areas to select Up/Down/Left/Right.
Press Up/Down/Left/Right on the button to select or set functions.
•Repeat
To use the Repeat function, press the Up button.
•Music Skip
Press the Right button to select the next music le. Press the Left button to select the
previous music le.
•Auto Power Link
You can turn Auto Power Link on or off.
– Auto Power Link : If the Soundbar is connected to your TV through a digital optical
cable, the Soundbar can automatically turn on when you turn on your TV. Press
and hold the Left button for 5 seconds to toggle Auto Power Link ON and OFF.
– Auto Power Link is set to ON by default.
•ID SET
Press and hold the Up button for 5 seconds to complete ID SET (when connecting to an
accessary item).
󱂚
Sound Control
VOL WOOFER
SOUND
MODE
PAIR
You can select from TREBLE, SYNC, REAR LEVEL,or REAR SPEAKER ON/OFF.
•To adjust the TREBLE volume, select Sound Control → TREBLE, and then use the
Up/Down buttons to adjust the volume within a -6 to +6 range.
•If the video on the TV and audio from the Soundbar are not synchronised, select SYNC
in Sound Control, and then set the audio delay between 0~300 milliseconds by using
the Up/Down buttons.
•If surround speakers (not supplied) are connected, select REAR LEVEL, and then use
the Up/Down buttons to adjust the volume within a -6 to +6 range.
The REAR SPEAKER function can be turned ON/OFF by using the Up/Down buttons.
•SYNC is only supported for some functions.

ENG - 19
󱂛
VOL WOOFER
SOUND
MODE
PAIR
BASS
SOUND
MODE
VOL BASS
SOUNDBAR
SOUND
MODE
VOL BASS
SOUNDBAR
SOUND
MODE
VOL BASS
SOUNDBAR
SOUND
MODE
VOL BASS
SOUNDBAR
Push the button up or down to adjust the BASS volume within a -6 to +6 range.
To set the BASS volume level to 0, press the button.
•When a Subwoofer (not supplied) is connected, the BASS button becomes the
Subwoofer button. Push the button up or down to adjust the subwoofer volume either
to -12 or within a -6 to +6 range. To set the subwoofer volume level to 0, press the
button.
󱂜
VOL WOOFER
SOUND
MODE
PAIR
VOL
SOUND
MODE
VOL BASS
SOUNDBAR
SOUND
MODE
VOL BASS
SOUNDBAR
SOUND
MODE
VOL BASS
SOUNDBAR
SOUND
MODE
VOL BASS
SOUNDBAR
Push the button up or down to adjust the volume.
•Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.

ENG - 20
Adjusting the Soundbar volume
with a TV remote control
If you have a Samsung TV, you can adjust
the Soundbar’s volume using the IR remote
control that came with your Samsung TV.
First use the TV menu to set the TV audio on your
Samsung TV to external speakers, then use your
Samsung remote to control the Soundbar’s
volume. For more information, see the TV’s user
manual. The default mode for this function is
control by a Samsung TV remote. If your TV is not
a Samsung TV, follow the directions below to
change the settings of this function.
1. Turn Off the Soundbar.
BYE
2. If you do not want to use this function, push
up and hold the BASS button on the remote
repeatedly for 5 seconds until “OFF-TV
REMOTE”appears in the display.
SOUND
MODE
VOL BASS
SOUNDBAR
OFF-TV REMOTE
5 Sec
3. If you want to control the Soundbar with
your TV’s remote, push up and hold the BASS
button for 5 seconds repeatedly until
“ALL-TV REMOTE” appears in the display.
Then, use your TV’s menu to select external
speakers.
SOUND
MODE
VOL BASS
SOUNDBAR
ALL-TV REMOTE
5 Sec
4. If you want to return the Soundbar to the
default mode (control by a Samsung TV
remote), push up and hold the BASS button
for 5 seconds repeatedly until “SAMSUNG-
TV REMOTE” appears in the display.
SOUND
MODE
VOL BASS
SOUNDBAR
SAMSUNG-TV REMOTE
5 Sec
(Default mode)
– Each time you push the BASS button up
and hold it for 5 seconds, the mode
switches in the following order:
“SAMSUNG-TV REMOTE” (Default mode)
→ “OFF-TV REMOTE” → “ALL-TV REMOTE”.
– This function may not be available,
depending on the remote control.
– For manufacturers that support this
feature, refer to the FULL MANUAL for
your Soundbar on the Samsung web site
(www.samsung.com/support).
– This volume control function works with
IR TV remotes only. It does not work with
Bluetooth TV remotes (remotes that
require pairing)