Samsung Cs21k9mazx/xst User manual

COLOR TELEVISION RECEIVER

Chassis : KS9A(P)

Model : CS21K9MAZX/XST

COLOR TELEVISION RECEIVER CONTENTS

Precautions

Specifications and IC Data

Disassembly and Reassembly

Alignment and Adjustment

Troubleshooting

Exploded View and Parts List

Electrical Parts List

Block Diagram

Wiring Diagram

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

SERVICE Manual

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protective

devices are replaced. Restore any missing

protective shields.

2. When reinstalling the chassis and its

assemblies, be sure to restore all protective

devices, including: nonmetallic control knobs

and compartment covers.

3. Make sure that there are no cabinet openings

through which people—particularly

children—might insert fingers and contact

dangerous voltages. Such openings include

the spacing between the picture tube and the

cabinet mask, excessively wide cabinet

ventilation slots, and improperly fitted back

covers.

If the measured resistance is less than 1.0

megohm or greater than 5.2 megohms, an

abnormality exists that must be corrected

before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):

Warning: Do not use an isolation

transformer during this test. Use a leakage-

current tester or a metering system that

complies with American National Standards

Institute (ANIS C101.1, Leakage Current for

Appliances), and Underwriters Laboratories

(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug

the AC line cord directly into the power

outlet. With the unit’s AC switch first in the

ON position and then OFF, measure the

current between a known earth ground (metal

water pipe, conduit, etc.) and all exposed

metal parts, including: antennas, handle

brackets, metal cabinets, screwheads and

control shafts. The current measured should

not exceed 0.5 milliamp. Reverse the power-

plug prongs in the AC outlet and repeat the

test.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:

With the unit’s AC plug disconnected from the

AC source, connect an electrical jumper across

the two AC prongs. Connect one lead of the

ohmmeter to an AC prong. Connect the other

lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to pro-

hibit X-ray emissions. To ensure continued

X-ray protection, replace the picture tube only

with one that is the same type as the original.

Carefully reinstall the picture tube shields and

mounting hardware; these also provide X-ray

protection.

8. High Voltage Limits:

High voltage must be measured each time ser-

vicing is done on the B+, horizontal deflection

or high voltage circuits. Correct operation of

the X-ray protection circuits must be

reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include

the X–ray Protection Specifications Label, and

the Product Safety and X-ray Warning Note on

the service data schematic.

Precautions

1-1

LEAKAGE

CURRENT

TESTER

DEVICE

UNDER

TEST TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED) EARTH

GROUND

(READING SHOULD

NOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential

hazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified

limits by close-tolerance, safety-related

components and adjustments. If the high

voltage exceeds the specified limits, check

each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or

electrical design of this unit. Example: Do not

add auxiliary audio or video connectors. Such

alterations might create a safety hazard. Also,

any design changes or additions will void the

manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically

connected directly to one conductor of the AC

power cord. If an isolation transformer is not

used, these units may be safely serviced only

if the AC power plug is inserted so that the

chassis is connected to the ground side of the

AC source.

To confirm that the AC power plug is inserted

correctly, do the following: Using an AC

voltmeter, measure the voltage between the

chassis and a known earth ground. If the

reading is greater than 1.0V, remove the AC

power plug, reverse its polarity and reinsert.

Re-measure the voltage between the chassis

and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground,

regardless of the AC plug polarity. These units

can be safely serviced only if an isolation

transformer inserted between the receiver and

the power source.

13. Some TV chassis have a secondary ground

system in addition to the main chassis ground.

This secondary ground system is not

isolated from the AC power line. The two

ground systems are electrically separated by

insulating material that must not be defeated

or altered.

14. Components, parts and wiring that appear to

have overheated or that are otherwise

damaged should be replaced with parts that

meet the original specifications. Always

determine the cause of damage or overheat-

ing, and correct any potential hazards.

15. Observe the original lead dress, especially

near the following areas: Antenna wiring,

sharp edges, and especially the AC and high

voltage power supplies. Always inspect for

pinched, out-of-place, or frayed wiring. Do

not change the spacing between components

and the printed circuit board. Check the AC

power cord for damage. Make sure that leads

and components do not touch thermally hot

parts.

16. Picture Tube Implosion Warning:

The picture tube in this receiver employs

“integral implosion” protection. To ensure

continued implosion protection, make sure

that the replacement picture tube is the same

as the original.

17. Do not remove, install or handle the picture

tube without first putting on shatterproof

goggles equipped with side shields. Never

handle the picture tube by its neck. Some

“in-line” picture tubes are equipped with a

permanently attached deflection yoke; do not

try to remove such “permanently attached”

yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have

special safety-related characteristics which

might not be obvious from visual inspection.

These safety features and the protection they

give might be lost if the replacement compo-

nent differs from the original—even if the

replacement is rated for higher voltage,

wattage, etc.

Components that are critical for safety are

indicated in the circuit diagram by shading,

( ) or ( ).

Use replacement components that have the

same ratings, especially for flame resistance

and dielectric strength specifications.

A replacement part that does not have the

same safety characteristics as the original

might create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

1-2 Servicing Precautions

1. Servicing precautions are printed on the

cabinet. Follow them.

2. Always unplug the unit’s AC power cord from

the AC power source before attempting to: (a)

Remove or reinstall any component or

assembly, (b) Disconnect an electrical plug or

connector, (c) Connect a test component in

parallel with an electrolytic capacitor.

3. Some components are raised above the printed

circuit board for safety. An insulation tube or

tape is sometimes used. The internal wiring is

sometimes clamped to prevent contact with

thermally hot components. Reinstall all such

elements to their original position.

4. After servicing, always check that the screws,

components and wiring have been correctly

reinstalled. Make sure that the portion around

the serviced part has not been damaged.

5. Check the insulation between the blades of the

AC plug and accessible conductive parts

(examples: metal panels, input terminals and

earphone jacks).

6. Insulation Checking Procedure: Disconnect the

power cord from the AC source and turn the

power switch ON. Connect an insulation

resistance meter (500V) to the blades of the AC

plug.

The insulation resistance between each blade

of the AC plug and accessible conductive parts

(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.

Do not apply AC power to the unit (or any of

its assemblies) unless all solid-state heat sinks

are correctly installed.

8. Always connect a test instrument’s ground

lead to the instrument chassis ground before

connecting the positive lead; always remove

the instrument’s ground lead last.

Precautions

1-3

Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between

the servicing and safety precautions, always follow the safety precautions.

Warning2: An electrolytic capacitor installed with the wrong polarity might explode.

1. Some semiconductor (“solid state”) devices

are easily damaged by static electricity. Such

components are called Electrostatically

Sensitive Devices (ESDs); examples include

integrated circuits and some field-effect

transistors. The following techniques will

reduce the occurrence of component damage

caused by static electricity.

2. Immediately before handling any semicon

ductor components or assemblies, drain the

electrostatic charge from your body by

touching a known earth ground. Alternatively,

wear a discharging wrist-strap device. (Be

sure to remove it prior to applying power—

this is an electric shock precaution.)

3. After removing an ESD-equipped assembly,

place it on a conductive surface such as

aluminum foil to prevent accumulation of

electrostatic charge.

4. Do not use freon-propelled chemicals. These

can generate electrical charges that damage

ESDs.

5. Use only a grounded-tip soldering iron when

soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.

Many solder removal devices are not rated as

“anti-static”; these can accumulate sufficient

electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its

protective package until you are ready to

install it. Most replacement ESDs are

packaged with leads that are electrically

shorted together by conductive foam,

aluminum foil or other conductive materials.

8. Immediately before removing the protective

material from the leads of a replacement ESD,

touch the protective material to the chassis or

circuit assembly into which the device will be

installed.

9. Minimize body motions when handling

unpackaged replacement ESDs. Motions such

as brushing clothes together, or lifting a foot

from a carpeted floor can generate enough

static electricity to damage an ESD.

Precautions

1-4 Samsung Electronics

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

Samsung Electronics 2-1

Specifications and IC Data

2. Specifications and IC Data

2-1 Specifications

Television System:

Channels:

Intermediate Frequencies (MHz) :

Picture Tube:

Power Requirements:

Antenna Input Impedance:

Speaker Impedance

NTSC - M

2 - 13

14-69

NTSC - M

38.90

34.40

35.32

PAL/SECAM-

B/G,I

2 - 12

21 - 69

PAL/

SECAM- B/G

38.90

33.40

34.47

System

Band

VHF

UHF

SYSTEM

IF Carrier Frequency

Picture IF Carrier

Sound IF Carrier

Color Sub Carrier

PAL,

SECAM- D/K

1 - 13

21 - 69

PAL/SECAM-D/K,

SECAM-K1

38.90

32.40

34.47

SECAM-K1,

PAL-D

2 - 9

13 - 57

PAL - I

38.90

32.90

34.47

MODEL

CI

CII

CX

CK

CW

CS

14 Inch

20 Inch

21 Inch

AC 160~300V, 50/60Hz

VHF, UHF : Telescopic dipole antenna (75 ohm unbalanced type )

8 ohm, 7W+7W (MAX)

SYSTEM

PAL-I (UHF)

PAL-I (VHF/UHF)

PAL-B/G, SECAM-B/G

PAL-B/G, D/K, SECAM-B/G, D/K

PAL-B/G, D/K, SECAM-B/G, D/K, NT 4.43

PAL-B/G, D/K, SECAM-B/G, D/K, NT4.43, NT3.58

A34KQV42X

A48KRD82X(H)

A51KQJ63X

Quick start, in-line-gun,

Black stripe, 90

degree deflection

21 Flat A51QDX993X

2-2 Samsung Electronics

2-2 IC Line Up

Specifications and IC Data

Loc. No Specification Description Remark

HC101 PAP103 IF PRE-AMP

IC501 TDA6107Q RGB DRIVE AMP

Table 2-1 IC Line-Up

IC902 24C08/KS28C040 EEPROM

PC801S TCET1108 / LTV817B PHOTO COUPLER

SPM802ER TTX, English/Croatian/Romanian/Hungarian/Polish/Czech/

Bulgarian/Russian/Portugal

IC201S Philips

Philips

SPM802ERN W/O TTX, English/Croatian/Romanian/Hungarian/Polish/Czech/

Bulgarian/Russian/Portugal

VERTICAL OUTPUT

LA7840

TDA7266S

IC301

IC601 SOUND-AMP (3W x 1CH or 3W x 2CH or 5W x 2CH)

IC801S KA5Q0765R POWER IC (STR)

IC802 KA7632 CUSTOM REGULATOR (5V, 8V, 3.3V)

IC101 U4468B SIF - IC TEMIC

Sanyo

2-3 Semiconductor Base Diagrams

Specifications and IC Data

Samsung Electronics 2-3

ELECTROLYTIC-

CONDENSER IC

DIODE

SPM-802ERN(Pin 64)

SPM-802ER(Pin 64)

X24CO8P(Pin 8)

KS24C080(Pin 8)

U4468B(Pin 16)

IC TRANSISTOR

LA7840

TDA6107Q

KA7632

TRANSISTOR

2SD1651

2SD1650

2SD2499

KSA614

BCEE B C

KSC815-Y

KSA539-Y

BC548

KTC9014

IC

UPC574J

or

KA33V

SAW-FILTER

E C B

KSR1012

KSR1010

KSR2010

KTD863-Y

KSC2331-Y

1

G3956M

K9260M

Fig. 2-1 Semiconductor Base Diagrams

2-4

MEMO

Samsung Electronics 3-1

Disassembly and reassembly

3. Disassembly and Reassembly

3-1 Back Cover Removal

1. After removing the screws, press the tension rib and pull the cabinet backwards.

2. To reassemble, press the tension rib (see diagram).

3-2 Samsung Electronics

3-2 Main Board Removal

Disassembly and reassembly

1. Separate the socket board from the CRT neck.

2. Remove the Anode Cap from the CRT.

3. Remove the main board by pulling it with both hands.

Warning: The FBT is charged with high voltage.

Before removing the Anode Cap, discharge the voltage

through one of the heat sinks on the main board.

3-3 Speaker Removal

Disassembly and reassembly

Samsung Electronics 3-3

1. Remove the speaker by

pressing the tension rib.

3-4 Samsung Electronics

Disassembly and reassembly

3-4 CRT Removal

1. Spread a soft mat on the floor. Place the TV set face

down.

2. Remove the 4 nuts mounting the CRT to the front cabi-

net. Lift the CRT.

3. Caution: Because of the high vacuum and large surface

area of the picture tube, be careful while handling it: (1)

Always lift the picture tube by grasping it firmly around

the faceplate, (2) Never lift the tube by its neck. (3) Do

not scratch the picture tube or apply excessive pressure.

Fractures of the glass may cause an implosion.

Samsung Electronics

Troubleshooting

5-1

5. Troubleshooting

5-1 No Video (Raster On, No Sound)

Yes

No

Open the IF Pin of Tuner

Check/Replace

TU01S

No

Measure the

Voltage of Each Pin

of TU01S

Check IC201S

Pins 2,3

See "No Video"

(Sound OK)

See "No Sound"

(Video OK)

Check/Replace

IC201S

Yes

No Check/Replace

IC501, IC201S

Check IC201S

Pins 40,49,50

See "No Sound"

(Video OK)

5-2 Samsung Electronics

5-2 No Power

Troubleshooting

Yes

No

Yes

No

Check the 125V,

13.0V B+Lines

Check IC802

Pin 8 (8V)

Pin 9 (9V)

Pin 10 (5V)

Check/Replace

IC801S, D801S, D802S,

D803S,D804S,FP801S

Check/Replace

IC802 (KA7632)

Check IC201S

Pin 1 : Stand-by : 0V

Normal : 3.3V

Check/Replace

IC201S

Check IC201S

Pin 1 (3.3V)

Check/Replace

IC201S, (µ-com).

Check IC201S,

Pin 33 (H-out) Check/Replace

IC201S, Q401, Q402.

5-3 No Video (Sound OK)

Troubleshooting

Samsung Electronics 5-3

Yes

No

Yes

No

Check IC201S

Pin 40 (CVBS) Check/Replace

IC201S

Check IC201S

Pins 38/R214, R215

Check IC201S

Pin 49 (V-GUARD)

Pin 50 (Cut-off)

Pin 51~53 (R,G,B-out)

Check/Replace

IC201S

Check IC501

on the CRT PCB Check/Replace

IC501

Check/Replace

R421, R505 (HEATER 6.3Vrms)

D503 (CRT G1 pin)

CRT, V999S

5-4 Samsung Electronics

Troubleshooting

5-4 No Sound (Video OK)

No

Check/Replace

A/V Front assembly.

Check IC201S

Pin 44 (Sound Out) Check/Replace

IC201S

Check IC601

Pin 3,13 (B+ 10-12.5V)

Check/Replace

Q904, IC201S

Check IC601 Check/Replace

IC601

Check IC601

Pins 6 (0V)

Check/Replace

R814, R815

Yes

No

Yes

5-5 No TTX

No

See No Video

Check IC201S Check/Replace

IC201S

Yes

6. Exploded View & Parts List

6-1 CS21K9MAZX/XST

Exploded View & Parts List

Samsung Electronics 6-1

T0074

T0003

T0022

T0607

T0057

T0023

CIS7

CIS3 T0066

T0238 T0522

M0014

CCM1

T0527

T0063

T0015

T0607 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- 1 S.N.A

CIS7 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, 1 S.N.A

T0238 AA64-01694B WINDOW REMOCON;15K2,ACRYL,CLR 1 S.N.A

CIS3 AA64-01697C DECORATION-POWER;15K2,ABS,HB,WHT,SVM6145 1 S.N.A

T0003 AA64-04036C CABINET FRONT;21K9 245(TSE),HB,G4309,SV0 1 S.N.A

T0023 AA64-04041A KNOB POWER;21K9(TSE),ABS,HB,G3676,SVM301 1 S.N.A

T0022 AA64-04043A KNOB CONTROL;21K9(TSE),ABS,HB,G3676,SVM3 1 S.N.A

T0057 AA64-70123A BADGE-BRAND;NEW,AL,L50,FLAT,SILVER,SAMSU 1 S.N.A

T0175 AA96-01178A ASSY SPEAKER P;8OHM,3001-001037,AA39-205 1 S.N.A

T0015 AA64-04038B CABINET BACK;21K9 245(TSE),FV2,GR503 1

T0527 AA65-00009B CLAMPER CORE-D,COIL;21A8,NYLON 66,V0,-,- 4 S.N.A

T0063 AA03-00403A CRT COLOR;A51QDX993X,0MG,1.75MH,18MH,3.1 1

T0066 AA96-20112C ASSY POWER CORD;-,EP2/NO,H/C250,KJ10,THA 1 S.N.A

M0014 AA94-14162C ASSY PCB MAIN;CS21K9MAZX/XST,KS9A,FULL M 1

T0074 AA59-00312C REMOCON;DEEP IMPACT,TM75,35,NON-TTX,EX,P 1

CCM1 AA60-10050R SCREW-MACHINE;-,SWRCH18A,M5,L31.5,HH,+,W 4 S.N.A

Loc. Code No Description Specification Q’ty S.N.A

You can search for the updated part code through ITSELF web site.

URL : http://itself.sec.samsung.co.kr

Electrical Parts List

Samsung Electronics 7-1

ASSY COVER FRONT

1 M0001 AA90-04281V ASSY COVER FRONT;CS21K9MAZX/XST 245,(TSE S.N.A

..2 CCM1 AA60-10050R SCREW-MACHINE;-,SWRCH18A,M5,L31.5,HH,+,W S.N.A

..2 T0081 AA60-10050T SCREW-TAPPING;-,SWRCH18A,M4,L20,RH,+,2S, S.N.A

..2 M0003 AA96-01170H ASSY COVER P-FRONT;21K9 245(TSE),HB,G430

...3 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR S.N.A

...3 T0607 AA61-40113A STOPPER-PCB;501H,HIPS,-,-,HB,NTR,- S.N.A

...3 CIS7 AA61-60003J SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, S.N.A

...3 T0238 AA64-01694B WINDOW REMOCON;15K2,ACRYL,CLR S.N.A

...3 CIS3 AA64-01697C DECORATION-POWER;15K2,ABS,HB,WHT,SVM6145S.N.A

...3 T0003 AA64-04036C CABINET FRONT;21K9 245(TSE),HB,G4309,SV0 S.N.A

...3 T0023 AA64-04041A KNOB POWER;21K9(TSE),ABS,HB,G3676,SVM301 S.N.A

...3 T0022 AA64-04043A KNOB CONTROL;21K9(TSE),ABS,HB,G3676,SVM3 S.N.A

...3 T0057 AA64-70123A BADGE-BRAND;NEW,AL,L50,FLAT,SILVER,SAMSU S.N.A

...3 AA65-00011C CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, S.N.A

...3 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, S.N.A

...3 T0175 AA96-01178A ASSY SPEAKER P;8OHM,3001-001037,AA39-205 S.N.A

....4 T0082 3001-001037 SPEAKER;5W,8OHM,89DB,180HZ

....4 T0245 AA39-20505N LEAD CONNECTOR-ASSY; ,4P,350,550MM,YSH02

...3 T0382 BP61-00509C HOLDER-CARE;PJT,ACRYL-FOAM,T0.25,W20.0mm S.N.A

..2 T0382 BP61-00495C HOLDER-CARE;PJT,ACRYL-FOAM,T0.25,W30.0mm S.N.A

ASSY COVER REAR

1 M0002 AA90-04283L ASSY COVER REAR;21K9 245(TSE),FV2,GR503, S.N.A

..2 T0015 AA64-04038B CABINET BACK;21K9 245(TSE),FV2,GR503

..2 AA64-60385B INLAY-BACK;50.5366,PS,T0.3,-,-,BLK,LINE S.N.A

..2 T0214 AA65-30008A CLAMPER CORE-CORD;-,PE,HB,-,BLK,- S.N.A

..2 T0069 AA60-00091K SPACER-FELT;-,FELT,330X10,-,-,BLK,T0.35, S.N.A

..2 T0069 AA60-00091J SPACER-FELT;-,FELT,330X10,-,-,BLK,T0.5,- S.N.A

ASSY FIXING

1 AA91-06496R ASSY FIXING;KS1A,MAC,THAILAND,CHINA,EP2 S.N.A

..2 T0245 AA39-20010D LEAD CONNECTOR-ASSY;,1P,400,YFH800-01,S,

..2 AA65-30009A CLAMPER CORE-FBT;-,ABS,V0,-,BLK,- S.N.A

..2 CLAMP AA65-30018A CLAMPER CORE-WIRE;DONG-A,NYLON-66,-,-,-, S.N.A

..2 AA65-30018A CLAMPER CORE-WIRE;DONG-A,NYLON-66,-,-,-, S.N.A

..2 AA65-30111A CLAMPER CORE-WIRE;ALL MODEL,NYLON,V0,-,W S.N.A

..2 T0066 AA96-20112C ASSY POWER CORD;-,EP2/NO,H/C250,KJ10,THA S.N.A

...3 3811-001609 WIRE-PVC CU;BCWA,300V,ROLL,-,#22,BLK S.N.A

...3 T0268 AA39-10006K CBF-POWER CORD;-,KJ-10,SPT-2 2/18AWG,240

...3 AA61-20284A HOLDER;P-CORD,PP,-,-,-,BLK,VO,KE-002 S.N.A

..2 AA61-01364A HOLDER-COVER;KS1A,NYLON66,BLK,V2 S.N.A

ASSY CPT

1 T0521 AA91-07790A ASSY CPT;CS21M16MGZXXSE,KS9A S.N.A

..2 T0089 AA27-00256A COIL DEGAUSSING;,21IHCH,10%,35TS,4.5OHM,

..2 T0527 AA65-00009B CLAMPER CORE-D,COIL;21A8,NYLON 66,V0,-,- S.N.A

..2 T0521 AA91-07819A ASSY CPT;CS21M16MHZXBWT,KS9A FLAT MST S.N.A

...3 T0063 AA03-00403A CRT COLOR;A51QDX993X,0MG,1.75MH,18MH,3.1

...3 T0079 AA27-00002A MAGNET CONVERGENCE;JH291-11D,29.1MM

...3 T0078 AA27-00324A DEFLECTION YOKE;,DIF-2192AA(A),S/T,A51QD

...3 AA63-60028A SPACER-DY;-,NEOPRENE,-,-,-,BLK,-,-,V0 W1 S.N.A

..2 AA98-70014D ASSY TBC WIRE P;TVI,22,NTSC,PAL,1P,UL101 S.N.A

ASSY CHASSIS

1 M0017 AA91-08248A ASSY CHASSIS;CS21K9MAZX/XST,KS9A,FULL MO S.N.A

..2 M0014 AA94-14162C ASSY PCB MAIN;CS21K9MAZX/XST,KS9A,FULL M

...3 0202-001366 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb, S.N.A

...3 T0083 0402-001230 DIODE-RECTIFIER;FMG-G2CS,1000V,3A,DO-41,

...3 T0083 0402-001599 DIODE-RECTIFIER;DGP30L,1500,3A,DO-201AD(

...3 T0090 0502-001160 TR-POWER;2SD2499,NPN,50000mW,TO-3P,BK,8-

...3 PC801S 0604-001032 PHOTO-COUPLER;TR,170-260%,300mW,DIP-4,ST

...3 IC112 1103-001106 IC-EEPROM;24C080,1Kx8Bit,DIP,8P,9.6x6.4m

...3 T0900 1404-001045 THERMISTOR-NTC;4.7ohm,15%,2900K,35.0mW,T

...3 P803T 1404-001265 THERMISTOR-PTC;4.5OHM/100OHM,+30/-20%,22

...3 C598 2201-000446 C-CERAMIC,DISC;3.3NF,20%,400V,Y5U,BK,15X

...3 C410A 2301-001385 C-FILM,LEAD-PPF;30nF,5%,630V,TP,20x15.5x

...3 CX801S 2306-000318 C-FILM,LEAD-PPF;220NF,20%,250V,BK,-,22.5

...3 CR410S 2306-000327 C-FILM,LEAD-PPF;6.3nF,3%,1.6KV,TP,28.5x1

...3 CR402S 2306-000350 C-FILM,LEAD-PPF;270NF,5%,400V,BK,26X18.5

...3 C701 2401-003030 C-AL;220uF,20%,450V,GP,BK,30x35,10

...3 X901 2801-004033 CRYSTAL-UNIT;12MHZ,30PPM,28-AAM,30PF,30O

...3 SF101S 2904-001143 FILTER-SAW AV;38.9MHz,SIP5K,ST,18dB,B/G,

...3 SW801S 3403-001134 SWITCH-PUSH;250V,5A,DPST,ON-OFF,-

...3 FP801S 3601-000281 FUSE-CARTRIDGE;250V,4A,TIME-LAG,GLASS,5.

...3 V999S 3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,-

...3 JS701 3722-001138 JACK-PIN;6P,3.4mm,SN,BLK,#16-22

...3 T0119 AA09-00412A IC MICOM;TDA9381PS/N2/3I,SPM-802EAN5,64P

...3 IC063 AA13-20004W IC HYBRID;-,PAP103T,SIP,6P,PRE-AMP,TP

...3 T801S AA26-00043A TRANS SWITCHING;-,-,-,AC90~260V,125/12.5

...3 T0616 AA26-00201A TRANS FBT;FCA173B,KS1A-1,3.8mH,FERRITE,1

...3 T401 AA26-50001B TRANS-HORIZ.DRIVE;-,-,-,7.1mH,-,-,102uH,

...3 T0296 AA27-00281A COIL LINEARITY;64UH,64UH,DR1215 C:4.5,7.

...3 LW01 AA27-00296A COIL CHOKE;220UH,CPTTV,220UH,10%,3A,DR14

...3 LX801S AA29-00015A FILTER LINE NOISE;WS32W8,28-20MH 1.5A,+-

...3 D0254 AA32-00015A MODULE REMOCON;FRP-3521H31,38KHZ,940MM,M

...3 T0245 AA39-20620C LEAD CONNECTOR-ASSY;,9P,500MM,YBNH250-09

...3 TU01S AA40-00076A TUNER;TECC0949PG35A(S),PAL,181CH,38.9MHZ

...3 GT301 AA60-40012D PIN-GT,ASSY;T1.6,6-12.5-,NYLON66 S.N.A

...3 AA95-03268B ASSY SUB PCB-STEREO;THAI,KS9A,A2,STEREO S.N.A

....4 0202-001366 SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb, S.N.A

....4 T0089 1204-000439 IC-IF CIRCUIT;TDA3845,DIP,16P,300MIL,PLA

....4 ICS01 1204-002026 IC-SOUND PROCESSOR;MSP3400G-PO-B8-V3,SDI

....4 XS01 2801-004020 CRYSTAL-UNIT;18.432MHz,30ppm,28-AAM,12pF

....4 SF102S 2904-000260 FILTER-SAW AV;38.9MHz,SIP5K,ST,26dB,B/G,

....4 CN906 3711-002706 CONNECTOR-HEADER;NOWALL,8P,1R,2.5mm,ANGL

....4 CN906 3711-002708 CONNECTOR-HEADER;NOWALL,10P,1R,2.5mm,ANG

....4 T0245 AA39-00276A LEAD CONNECTOR-ASSY;,UL1185#26,UL/CSA,6P

....4 HCP01 AA61-10068A BRACKET-PCB;M2160,SPTE,T0.3,-,-,-,- S.N.A

....4 AA97-14836B ASSY AUTO-STEREO;THAI,KS9A,A2,STEREO S.N.A

.....5 CISS 0401-000005 DIODE-SWITCHING;1N4148,75V,150MA,DO-35,T

.....5 T0156 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T

.....5 ICS02 1203-000515 IC-VOL. DETECTOR;7042,TO-92,3P,177MIL,PL

.....5 R125 2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM

.....5 R125 2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM

.....5 R125 2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM

.....5 R125 2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM

7-1 CS21K9MAZX/XST

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

7. Electrical Parts List

You can search for the updated part code through ITSELF web site.

URL : http://itself.sec.samsung.co.kr

.....5 R125 2001-000515 R-CARBON;220OHM,5%,1/8W,AA,TP,1.8X3.2MM

.....5 R125 2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM

.....5 R125 2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM

.....5 C598 2201-000112 C-CERAMIC,DISC;1.5NF,10%,50V,Y5V,TP,5X3.

.....5 C598 2201-000304 C-CERAMIC,DISC;0.001NF,0.25PF,50V,C0G,TP

.....5 C598 2201-000471 C-CERAMIC,DISC;0.33NF,10%,50V,Y5P,TP,4X3

.....5 C689 2202-000121 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP

.....5 C689 2202-000127 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V

.....5 C689 2202-000279 C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.

.....5 C689 2202-000286 C-CERAMIC,MLC-AXIAL;56pF,5%,50V,SL,TP,1.

.....5 C689 2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3

.....5 C2560 2301-000111 C-FILM,LEAD-PEF;1.8nF,5%,50V,TP,6.5x3.0x

.....5 C2560 2301-000383 C-FILM,LEAD-PEF;10nF,5%,50V,TP,6x7x3.2mm

.....5 C2560 2305-000665 C-FILM,LEAD-PEF;100nF,5%,63V,TP,7.5x4.0x

.....5 C701 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

.....5 C701 2401-001026 C-AL;3.3UF,20%,50V,GP,TP,5X11,5

.....5 C701 2401-001271 C-AL;4.7uF,20%,50V,GP,TP,4x7mm,5mm

.....5 C701 2401-002075 C-AL;4.7uF,20%,50V,GP,TP,5x11,5

.....5 C701 2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5

.....5 C701 2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5

.....5 LS02 2701-000114 INDUCTOR-AXIAL;10UH,10%,2534

.....5 LS03 2701-000114 INDUCTOR-AXIAL;10UH,10%,2534

.....5 LS01 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2534

.....5 LS04 2701-000184 INDUCTOR-AXIAL;4.7UH,10%,2534

.....5 T101 AA26-10001Z TRANS RF;-,7MG,VIF,-,7mm,100pF,38.9MHz,

.....5 AA41-01028B PCB SUB-STEREO MODULE;21M16/21M20,FR-1,1 S.N.A

...3 IC801S AA96-00242D ASSY HEAT SINK P;SCREWAA62-30186B,5Q0765 S.N.A

....4 CIS 0205-001154 OIL-SILICON;G746,-,- S.N.A

....4 T0086 1203-002916 IC-PWM CONTROLLER;KA5Q0765RTH-YDTU,TO-22

....4 T0081 6003-000333 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW S.N.A

....4 CIS AA62-30186B HEAT SINK-ES;-,-,-,SILVER,171J + COVER-H S.N.A

....4 CIS AA63-30189A COVER-HEATSINK;-,PC-ABS,T0.8,-,-,V0,NTR, S.N.A

...3 D806 AA96-00243D ASSY HEAT SINK P;-,BRIDGE,AA62-00045A,D0 S.N.A

....4 0205-001153 GREASE-SILICON;SC102,JAPAN,- S.N.A

....4 T0083 0402-001374 DIODE-RECTIFIER;FFPF06U20S,200V,6A,TO-22

....4 T0081 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR S.N.A

....4 AA62-00045A HEAT SINK-PS;-,-,T1.0,-,-,DREAM,-,-,-,-, S.N.A

...3 IC601 AA96-00244G ASSY HEAT SINK P;-,AUDIO,AA62-00046A,TDA S.N.A

....4 0205-001153 GREASE-SILICON;SC102,JAPAN,- S.N.A

....4 T0085 1201-001741 IC-AUDIO AMP;TDA8944J,DBS,17P,937MIL,DUA

....4 T0081 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR S.N.A

....4 AA61-10162B BRACKET-IC;-,SBHG-1,T1.0,-,-,-,100 S.N.A

....4 AA62-00046A HEAT SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X S.N.A

...3 IC301 AA96-00244M ASSY HEAT SINK P;SCREWAA64-00046A,LA7804 S.N.A

....4 CIS 0205-001154 OIL-SILICON;G746,-,- S.N.A

....4 T0088 1204-002121 IC-VERTICAL DEF.;LA78040N,TO220,7P,-,PLA

....4 T0081 6003-000335 SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR S.N.A

....4 CIS AA62-00046A HEAT SINK-PS;-,-,T1.0,-,D1(DREAM) 60X25X S.N.A

...3 IC802 AA96-00245A ASSY HEAT SINK P;,AA62-00055A,KA7632 S.N.A

....4 IC062 1203-001939 IC-MULTI REG.;7632,SIP,10P,-,PLASTIC,3.3

....4 T0081 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR S.N.A

....4 AA62-00055A HEAT SINK-PS;-,-,T1.0,-,35*15*25,D1,-,-, S.N.A

...3 LD901 AA96-00555A ASSY LED GUIDE;-,-,UEX-LD-030,GREEN S.N.A

...3 IC501 AA96-50311A ASSY HEAT SINK P;-,VIDEO,AA62-30175D,TDA S.N.A

....4 T0074 1201-001159 IC-VIDEO AMP;6107,ZSIP,9P,-,SINGLE,-,PLA

....4 T0081 6003-000334 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR S.N.A

....4 AA62-30175D HEAT SINK-PS;-,SECC,T1.0,-,33X15X30 FT-2 S.N.A

...3 AA97-14987C ASSY AUTO-MAIN;CS21K9MAZX/XST,KS9A,FULL S.N.A

....4 CISS 0401-000005 DIODE-SWITCHING;1N4148,75V,150MA,DO-35,T

....4 T0083 0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP

....4 T0083 0402-000254 DIODE-RECTIFIER;RGP10J,600V,1A,DO-41,TP

....4 T0083 0402-000493 DIODE-RECTIFIER;1R5GU41,400V,1.5A,DO-15L

....4 T0083 0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP

....4 T0083 0402-000546 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T

....4 T0083 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A,-,TP

....4 T0083 0402-001352 DIODE-RECTIFIER;GUF15G-20A,400V,1.5A,MEL

....4 DZ016 0403-000508 DIODE-ZENER;MTZJ5.6B,5.45-5.73V,500MW,DO

....4 DZ016 0403-000510 DIODE-ZENER;MTZJ6.2B,5.96-6.27V,500MW,DO

....4 DZ016 0403-000699 DIODE-ZENER;TZP27B,27-30.8V,1000MW,DO-41

....4 DZ016 0403-000700 DIODE-ZENER;TZP33A,5%,1000MW,DO-41,TP

....4 DZ016 0403-000720 DIODE-ZENER;MTZJ9.1B,8.57-9.01V,500MW,DO

....4 DZ016 0403-001140 DIODE-ZENER;RD10ESAB-T4,9.7-10.2V,400MW,

....4 DZ016 0403-001221 DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,D

....4 DZ016 0403-001317 DIODE-ZENER;MTZJ3.0B,3.01-3.22V,500MW,DO

....4 DZ016 0403-001318 DIODE-ZENER;MTZJ4.3B,4.17-4.43V,500MW,DO

....4 DZ016 0403-001319 DIODE-ZENER;MTZJ4.7C,4.68-4.93V,500MW,DO

....4 DZ016 0403-001322 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500MW,DO

....4 DZ016 0403-001327 DIODE-ZENER;MTZJ18A,16.22-17.06V,500MW,D

....4 DZ016 0403-001328 DIODE-ZENER;MTZJ22A,20.15-21.2V,500MW,DO

....4 T0156 0501-000283 TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,T

....4 T0156 0501-000369 TR-SMALL SIGNAL;KSC2331-Y,NPN,1000mW,TO-

....4 T0156 0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T

....4 T0090 0502-000242 TR-POWER;KSA614,PNP,25W,TO-220,TP,40-24

....4 Q902 0504-001159 TR-DIGITAL;SRC1211M,NPN,400MW,10KOHM,TO-

....4 IC012 1203-001217 IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL

Electrical Parts List

7-2 Samsung Electronics

Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark

Samsung CS21K9MAZX/XST User manual

Popular TV manuals by other brands