Samsung CW29M206VNXXEC User manual

DIGITAL TELEVISION RECEIVER
Chassis : S61A(P) Rev.2
Model : CW29M206VNXXEC
CS29M6SSNX/BWT
DIGITAL TELEVISION RECEIVER CONTENTS
Specifications
Alignment and Adjustments
Exploded Views and Parts List
Electrical Parts List
PCB Diagram
Schematic Diagrams
1.
2.
3.
4.
5.
6.
SERVICE Manual

Specifications
Samsung Electronics 1-1
1. Specifications
Country INDEX
F
I
X
E
D
OriginMark Madeinlocal countryofMade in KOREA(Samsung)
Color
Demodulation
Demodulation
PAL/SECAM/NTS C 4 .43 /NTSC3. 58
Sound
Receiving was Quasi-split
Sound VIRTUAL DOLBY(NICAM/STEREO)
Antenna 75ohmDIN - Jack(V/U)
Channel search F/S REMOCON
Channel numbers Air+CATV (41CH)
InputvoltageAC 160V~300V
Power Input
frequency 50Hz
PowerSTR 5Q1565RF
Power insulation SMPS/C OLD
U
n
f
i
x
e
d
Receiving(P/G)CHVHF: 2~12, UHF: 21~69 , CATV: S1~S41CH
BRAND/BUYERSAMSUNG/BWT (Depend on the Buyer)
Safety GOST
Powercord /
Polarity CP2/NO
Character
*Simple 100HzSCAN
*2SCART S / HALF TONE O S D
*2T-PIP

Alignment andAdjustments
Samsung Electronics 2-1
2. Alignment and Adjustments
2-1 Adjustments
2-1-1 General Alignment Instructions
Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic
characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for
good black and white details. There must be no objectionable color shading: If color shading is
present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments.
Note :
1. This ‘4. Alignment and Adjustments’ applies to S61A chassis applications.
2. AC Power Supply: 160~300V or 100~240V, 50Hz
3. This service manual has been written on the basis of domestic remote-control model adopting S61A
chassis. Depending on sales location and product specifications, some of specifications herein may
be changed.
2-1-2 Focus Adjustment
S61A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust in the
following sequence:
Focus Adjustment
1. Input a crosshatch pattern.
2. Select “Standard” from the menu,
3. Turn the Static Focus VR clockwise to set it to its maximum.
4. Turn the Static Focus VR counterclockwise slowly for the clearest
center vertical line.
5. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.
6. Check for the FOCUS of entire screen. If necessary,
re-do adjustments 3~5.
hGh

Alignment andAdjustments
2-2 Samsung Electronics
2-1-3 Screen Voltage Adjustment
1. Input a Toshiba pattern.
2. Use an oscilloscope to identify RK, BK, GK. And then adjust FBT Screen VR so that the voltage of
pedestal level doesn’t exceed 160V.
If a Toshiba pattern is not available, cancel the blue screen and input “No Signal” to AV IN so the voltage
of pedestal level doesn’t exceed 175V.
If an oscilloscope is not available, use a DC multi-meter in No Signal (black screen) to adjust RK, BK, GK
so that the highest voltage becomes 160Vp-p.
2-1-4 White Balance Adjustment
1. Warm up the TV set for at least 30 minutes.
2. Enter the Service Mode by pressing the remote control keys in the following sequence:
Power Off ½ Display ½ Menu ½ Mute ½ Power On
3. Initialize all set data.
4. Input a Toshiba pattern.
5. Using a probe(CA100), do the White Balance adjustments.
(1) Adjust Low-Light.
- Adjust Sub Brightness to set Y.
- Adjust B Cutoff to set y.
- Adjust R Cutoff to set x.
(2) Adjust High-Light.
- Adjust Sub Contrast to set Y.
- Adjust B Drive to set y.
- Adjust R Drive to set x.
(3) Check the value of Low-Light. If necessary, readjust Low-Light.
(4) Check the value of High-Light. If necessary, readjust High-Light.15

Alignment andAdjustments
Samsung Electronics 2-3
2-1-5 When adjusting Screen Voltage and White Balance
1. Screen Voltage and White Balance are related each other. Make sure both adjustments are correct.
2. Adjust Screen Voltage before White Balance Adjustments. Make sure Screen Voltage is correct.
3. If White Balance has been readjusted, re-check Screen Voltage.
4. After adjustments are complete, check the following.
- If spots appear on the screen after pressing the Power On/Off key, readjust Screen Voltage.
- If flyback lines appear on the screen, readjust Screen Voltage.

Alignment andAdjustments
2-4 Samsung Electronics
2-2 MICOM PORT

Alignment andAdjustments
Samsung Electronics 2-5

Alignment andAdjustments
2-6 Samsung Electronics

Alignment andAdjustments
Samsung Electronics 2-7
2-3 Factory Adjustment
2-3-1 Factory Adjustment values
SERVICE
Deflection
VideoAdjust1
VideoAdjust2
VideoAdjust3
VideoAdjust4
YC Delay
EEPROM
Option
CheckSum
Reset
SERVICE
Deflection
480/576P Deflect offset
1080i Deflection offset
VideoAdjust1
VideoAdjust2
VideoAdjust3
VideoAdjust4
DTV VideoAdjust
YC Delay
EEPROM
Option
CheckSum
Reset
European Model The Others Model

Alignment andAdjustments 2-8 Samsung Electronics
2-3-2 Factory Data
DEFLECTION : PAL
ITEMS CIS Europe China Asia M.Asia REMARK
29” 32” 34" 28" 29" 32” 29" 34" 29” 32” 34" 29” 32”
V-AMP 26 26 26 26 26 26 26 26 26 26 26 26 26 Vertical AMP adj( Gain Control)
V-SHIFT 30 30 30 30 30 30 30 30 30 30 30 30 30 Vertical Position adj (DC bias adj)
H-EW 33 33 33 33 33 33 33 33 33 33 33 33 33 Horizontal AMP adj(Gain Control)
H-SHIFT 35 35 35 35 35 35 35 35 35 35 35 35 35 Horizontal Position adj (DC bias adj)
V-Linearity 6 6 6666 5 5 6 6 6 6 6Vertical Linearity adj(TOP/Bottom adj)
UP-Linearity 8 888 8 8 8 8 8 8 8 88Vertical Linearity adj(TOP adj)
LOW-Linearity 4 4 4444 4 4 4 4 4 4 4Vertical Linearity adj(Bottom adj)
V-SC 5 55 5 5 5 5 5 5 5 5 55Vertical S correction adj
H-Parablar 48 48 48 48 48 48 48 48 48 48 48 48 48 Horizontal pin distortion adj
UP-Coner 35 35 35 35 35 35 35 35 35 35 35 35 35 Horizontal pin distortion up adj
LOW-Coner 36 36 36 36 36 36 36 36 36 36 36 36 36 Horizontal pin distortion low adj
H-Trapezium 12 12 12 12 12 12 12 12 12 12 12 12 12 Horizontal Trapezium distortion adj
BOW 31 31 31 31 31 31 31 31 31 31 31 31 31 Vertical line slope adj(parabola)
ANGLE 25 25 25 25 25 25 25 25 25 25 25 25 25 Vertical Linearity adj(sawtooth)
V-Position 40 40 40 40 40 40 40 40 40 40 40 40 40 V-POSITION ADJ as to CRT INCH
CXA 2151 Sub01 68 68 68 68 68 68 68 68 68 68 68 68 68
CXA 2151 Sub02 1 1 1 1 1 1 11 1 1 1 1 1