Samsung Plasma TV User manual

imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
Model Serial No.
Plasma TV
user manual
BN68-01938A-Eng.indb 1 2009-03-17 오후 8:53:43

Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Country Customer Care Centre Web Site
AUSTRALIA 1300 362 603 www.samsung.com/au
CHINA
800-810-5858
400-810-5858
010-6475 1880
www.samsung.com/cn
HONG KONG : 3698-4698 www.samsung.com/hk
INDIA
3030 8282
1800 110011
1800 3000 8282
www.samsung.com/in
INDONESIA 0800-112-8888 www.samsung.com/id
JAPAN 0120-327-527 www.samsung.com/jp
MALAYSIA 1800-88-9999 www.samsung.com/my
NEW ZEALAND 0800 SAMSUNG (0800 726 786) www.samsung.com/nz
PHILIPPINES
1-800-10-SAMSUNG(726-7864)
1-800-3-SAMSUNG(726-7864)
02-5805777
www.samsung.com/ph
SINGAPORE 1800-SAMSUNG(726-7864) www.samsung.com/sg
SOUTH AFRICA 0860-SAMSUNG(726-7864 ) www.samsung.com/za
TAIWAN 0800-329-999 www.samsung.com/tw
THAILAND 1800-29-3232
02-689-3232 www.samsung.com/th
TURKEY 444 77 11 www.samsung.com/tr
U.A.E 800-SAMSUNG (726-7864)
8000-4726 www.samsung.com/ae
VIETNAM 1 800 588 889 www.samsung.com/vn
BN68-01938A-00
BN68-01938A-Eng.indb 2 2009-03-17 오후 8:53:44

User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more
than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image
retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not
install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper
part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be
prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to
produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of
the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,
right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a
game console may cause similar effect to the screen. Damages caused by the above effect are not covered by
the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures,
high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may
cause a serious damage to your set.
© 2009 Samsung Electronics Co., Ltd. All rights reserved.









-
-

English - 2
BN68-01938A-Eng.indb 2 2009-03-17 오후 8:53:44

Contents
Connecting and Preparing Your TV
Checking Parts .......................................................................... 4
Using the Stand-Base ...............................................................4
Assembling the Cables.............................................................. 4
Viewing the Control Panel ......................................................... 5
Viewing the Connection Panel...................................................6
Remote Control ......................................................................... 7
Installing Batteries in the Remote Control ................................. 8
Switching On and Off.................................................................8
Placing Your Television in Standby Mode.................................. 8
Viewing the Menus .................................................................... 9
Using the TOOLS Button........................................................... 9
Plug & Play Feature ................................................................10
Channel Control
Storing Channels ................................................................... 11
Managing Channels ................................................................ 12
Picture Control
Changing the Picture Settings.................................................13
Setting up the TV with your PC ...............................................15
PC Display............................................................................... 16
Sound Control
Changing the Sound Setting ................................................... 17
Selecting the Sound Mode ......................................................18
Function Description
Conguring the Setup Menu.................................................... 19
Viewing the Picture in Picture (PIP).........................................20
Setting the Time ...................................................................... 21
Source List / Edit Name........................................................... 22
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Media Play
Using the Media Play Function................................................ 23
Using the PHOTO (JPEG) List ................................................ 25
Using the Music (MP3) List .....................................................28
Using the Setup Menu.............................................................29
About Anynet+
Connecting Anynet+ Devices .................................................. 30
Setting Up Anynet+ ................................................................. 31
Scanning and Switching between Anynet+Devices................ 31
Recording ................................................................................ 32
Listening through a Receiver (Home theater) .........................33
Troubleshooting for Anynet+.................................................. 33
Recommendations for Use
Teletext Feature....................................................................... 34
Wall Mount Kit Specications (VESA) ..................................... 35
Preparation before installing the Wall-Mount........................... 36
How to assemble the Stand-Base (depending on the model) . 36
Securing the TV to the Wall..................................................... 37
Securing the Installation Space...............................................37
Troubleshooting ....................................................................... 38
Specications .......................................................................... 39
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
N O T
Symbol Press Note One-Touch Button TOOLS
English - 3
English
BN68-01938A-Eng.indb 3 2009-03-17 오후 8:53:44

Connecting and Preparing Your TV
Checking Parts
Owner’s
Instructions
Remote Control/
AAA Batteries (2ea)
Power Cord Cloth-Clean Holder-Ring (4ea)
(Refer to page 36)
Warranty Card/
Safety Guide Manual
(Not available in all locations)
Cover-Bottom /
Screws (2ea)
(PS58B550 only)
Cover-Bottom
(PS50B550 only)
Screw (4ea)
(PS50B550 only)
Ferrite Core for
Power Cord
Ferrite Core for
Headphone
Holder-Wire Cable
(Not available in all locations)
Ferrite Core (Power Cord, Headphone)
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it around the cable near the plug.
N
Using the Stand-Base
Two or more people should carry the PDP. Never lay the PDP on the oor
because of possible damage to the screen. Always keep the PDP upright.
The PDP can rotate 20 degrees in right and left directions.
N
N
Assembling the Cables
Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the
transparent stand.
-20° ~ 20°
English - 4
BN68-01938A-Eng.indb 4 2009-03-17 오후 8:53:46

Viewing the Control Panel
1
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, Component1, Component2, PC, HDMI1,
HDMI2/DVI, HDMI3, HDMI4).
In the on-screen menu, use this button as you would use
the ENTER
E
button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
3 + VOL -
Press to increase or decrease the volume. In the on-screen
menu, use the + VOL - buttons as you would use the
◄ and ► buttons on the remote control.
N
4
<CH >
Press to change channels. In the on-screen menu, use the
<CH >buttons as you would use the ▲ and ▼ buttons on
the remote control.
5
POWER INDICATOR
Blinks and turns off when the power is on and lights up in
stand-by mode.
6 (
POWER)
Press to turn the TV on and off.
7
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
8
SPEAKERS
English - 5
The product colour and shape may vary depending on the model. N
Front Panel buttons
Touch each button to
operate.
BN68-01938A-Eng.indb 5 2009-03-17 오후 8:53:47

Viewing the Connection Panel
Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
N
N
1POWER IN
Connect the supplied power cord.
2AV IN (VIDEO / AUDIO R/L)
Video and audio inputs for external devices, such as a
camcorder or VCR.
3PC IN
Connect to the video output jack on your PC.
PC / DVI AUDIO IN
Connect to the audio output jack on your PC.
4COMPONENT IN 1, 2
Audio (AUDIO R/L) and video (Y/PB/PR) inputs for
Component.
5HEADPHONES JACK
You can connect a set of headphones if you wish to watch a
television programme without disturbing the other people in
the room.
Prolonged use of headphones at a high volume may
damage your hearing
6AUDIO OUT(AUDIO R/L)
Connect RCA audio signals from the TV to an external source,
such as Audio equipment.
7HDMI IN 1, 2(DVI), 3, 4
No additional Audio connection is needed for an HDMI to
HDMI connection.
Whenusing an HDMI/DVI cable connection, you must use
the HDMI IN 2(DVI) jack.
N
-
-
What is HDMI?
“High Denition Multimedia interface” allows the
transmission of high denition digital video data and
multiple channels of digital audio.
The HDMI/DVI terminal supports DVI connection to
an extended device with the appropriate cable (not
supplied). The difference between HDMI and DVI is
that the HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection) coding feature
installed, and supports multi - channel digital audio.
PC / DVI AUDIO IN
DVI audio outputs for external devices.
8 ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
9USB
Connect a USB mass storage device to view photo les and
play audio les.
0AV IN 2 (VIDEO / AUDIO R/L)
Video and audio inputs for external devices, such as a
camcorder or VCR.
Supported modes for HDMI/DVI and Component
480i 480p 576i 576p 720p 1080i 1080p
HDMI/DVI 50Hz X X X O O O O
HDMI/DVI 60Hz X O X X O O O
Component O O O O O O O
N
-
-
English - 6
Cable Television
Network
or
or
The product colour and shape may vary depending on the model. N
TV Rear Panel TV side Panel
42 65
1
3
8
7
0
9
BN68-01938A-Eng.indb 6 2009-03-17 오후 8:53:49

Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
The performance of the remote control may be affected by bright light. N
1
POWER button
(turns the TV on and off)
2
Selects the TV mode directly.
3
Number buttons for direct channel
access
4
Use to select on-screen menu items
5
Temporary sound switch-off
6 Volume increase
Volume decrease
7
Available source selection
8
Channel control button
9
Use to quickly select frequently used
functions.
0
Control the cursor in the menu
!
Use to see information on the current
broadcast
@
Use these buttons in the, Media Play,
etc.
$
Sound mode selection
%
Use these buttons in the Anynet+ and
Media Play.
^
Previous channel
&
Next channel
Previous channel
*
Displays the main on-screen menu
(
Selects the HDMI mode directly
)
Returns to the previous menu
a
Exit the on-screen menu
b
MEDIA.P (Media play)
This function enables you to view and
play photo and music files from an
external device. (Refer to pages 25
(Photo) and 28 (Music))
c
Picture size selection
d
Press to select the sound mode.
e
Sele cts SRS TruSurround HD mode.
Teletext Functions
2
Exit from the teletext display
(depending on the model)
7
Teletext mode selection (LIST/FLOF)
8
Teletext store
9
Teletext size
!
Teletext reveal
@
Fastext topic selection
#
Teletext display/mix both
teletext information and the normal
broadcast
^
Teletext sub page
&
P :Teletext next page
P :Teletext previous page
*
Teletext index
)
Teletext hold
a
Teletext cancel
English - 7
BN68-01938A-Eng.indb 7 2009-03-17 오후 8:53:50

Installing Batteries in the Remote Control
1. Lift the cover at the back of the remote control upward as shown in the gure.
2. Install two AAA size batteries.
Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside
the compartment.
3. Close the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the
remote control for a long time.
If the remote control doesn’t work, check the following
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?
N
Switching On and Off
The mains lead is attached to the rear of your set.
1. Plug the mains lead into an appropriate socket.
The standby indicator lights up on your set.
2. Press the POWERPbutton on your set.
You also can press the POWERPbutton or the TV button on the remote control to turn the TV on.
The programme that you were watching last is reselected automatically.
3. Press the numeric button (0~9) or channel up / down (</ >) button on the remote control or < CH > button on your set.
When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.
4. To switch your set off, press the POWERPbutton again.
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1. Press the POWER
P
button on the remote control.
The screen is turned off and a red standby indicator appears on your set.
2. To switch your set back on, simply press the POWER
P
, numeric buttons (0~9), TV button or channel up / down (</ >) button
again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug
the set from the mains and aerial.
N
N
N
N
N
N
N
English - 8
BN68-01938A-Eng.indb 8 2009-03-17 오후 8:53:51

Viewing the Menus
1. With the power on, press the MENU button. The main menu appears on the screen.
The menu’s left side has icons: Picture, Sound, Channel, Setup, Input.
2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER
E
button
to access the icon’s sub-menu.
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The TOOLS menu changes depending on
which external input mode you are viewing.
1. Press the TOOLS button. The TOOLS menu will appear.
2. Press the ▲ or ▼ button to select a menu, then press the ENTER
E
button.
3. Press the ▲ / ▼ / ◄ / ► / ENTER
E
buttons to display, change, or use the selected
items. For a more detailed description of each function, refer to the corresponding page.
Anynet+(HDMI-CEC), see page 31
Picture Mode, see page 13
Sleep Timer, see page 21
Energy Saving, see page 19
PIP, see page 20
Auto Adjustment, see page 15
•
•
•
•
•
•
N
English - 9
Move Enter Exit
Mode : Standard
Cell Light 8
Contrast 95
Brightness 45
Sharpness 50
Colour 50
Tint (G/R) G 50 R 50
Advanced Settings
Picture Options
Reset : OK
Picture
T V
TOOLS
Anynet+ (HDMI-CEC)
Picture Mode : Standard
Sleep Timer : Off
Energy Saving : Off
Enter ExitMove
BN68-01938A-Eng.indb 9 2009-03-17 오후 8:53:51