Samsung UN46C6500VFXZA Programming manual

UN46C6500VFXZA
FIRMWARE
2/21/2011
(T-VALAUSC, 1035.0)
Reason: Support Netflix 2.1 and MLB.tv
apps. Support new TV camera (Model:
CY-STC1100). Add "3D Optimize" option
on Menu for better 3D image.(Only
LCD/LED TV)
Previous: 1032.0
Prevents :
-USB Power Overload' message pops up
even USB port is not connected
-Plug & Play is displayed upon power up.
Please check Samsung.com for latest update! 
SERVICE BULLETINS
ASC20110621002
2010 LED Option Byte Table. It is
important to verify the correct
option byte is set.
Please check GSPN for parts update!
HELP : 1-888-751-4086 (Tech Support)
1-866-894-0637 (FE)
GSPN
PLUS ONE
http://my.plus1solutions.net/clientPortals/samsung
HOT TIPS
Power On Problems: (see page 2)
Video Problems: (see page 3.4)
Other:
HDMI Bleed-over
Fast Track Troubleshooting Manual Rev –1/12/12
1
Insert Photo of TV Board Layout
Include Board Assy names (as appearing in parts) and any
special labels/items (i.e. Plasma voltage label)
SMPS
Speaker T-CON
(below Bracket)
Main
Speaker
Woofer Version Parts No Short Description
ALL BN44-00356A SMPS
SQ01 BN94-03370F Main PCB
HQ03 BN94-03370Q Main PCB
H304 BN94-03370Q Main PCB
CN02 BN94-03370X Main PCB
HQ03 BN94-03370Y Main PCB
AA05 BN94-04684C Main PCB
ALL BN96-15397C Function & IR PCB
CN02 BN07-00854A Panel
SQ01 BN07-00860A Panel
AA05 BN07-00934A Panel
SQ01 BN81-04355A T-CON PCB
CN02 BN81-04456A T-CON PCB
H304 BN81-05772A T-CON PCB
HQ03 BN81-05772A T-CON PCB
HQ03 BN95-00413A Panel
H304 BN95-00413B Panel
AA05 BN96-13687A T-CON PCB
ALL BN63-06543B Back Bottom Cover
ALL BN96-13131A Stand Guide
ALL BN96-13133A Stand Base
ALL BN96-13748A Front Cover
ALL BN96-13843A Rear Cover
ALL 3903-000527 Power Cord
ALL BN40-00162A Tuner
ALL BN96-12723M LVDS Cable
http://gspn3.samsungcsportal.com

Fast Track Troubleshooting Manual
Power On Sequence:
1. Standby Voltages: CN201-2, 4 (5V)
2. Power On probable error on CN201-2
or 4 PS_ON )
3. Low Voltage Supplies On CN201-
5,6,7,13,17
4. Back Light Supply On CN201 -16
5. Back Light Confirmation CN201-18 2
Wiring Diagram
Include Connector Numbers , References, and
Locations.
C
N
2
0
1
S
I
G.
P
I
N
S
I
G.
1B12V 10 GND
2A5V 11 GND
3B12V 12 H_OUT
4A5V 13 B13V
5B5V 14 PWM
Dimming
6B5V 15 B13V
7B5V 16 B5V
8GND 17 B13V
9GND 18 IP_DET
UN46C6500VFXZA
LVDS
Cable
To Force Backlight On
without Main Board :
1. Remove Power Cord
2. Disconnect CN201
3. Plug In Power Cord
4. Backlight should be
on immediately.

3
2011 LED 8000 SeriesTROUBLESHOOTING VIDEO PROBLEMS
1. Verify Video Operation
a. Customer Picture Test (models available)
b. “Display” (If display is OK source is suspected)
C. Substitute with known good Source
(external DVD or Signal Generator)
2. Using Test Patterns in Service Mode
-ENTER SERVICE MODE –
1. Select an active source signal. (HDMI preferred)
Test Pattern may rely on signal source to appear.
Customer Remote Service Remote
2. Power off 2. Power On
3. Mute, 182, Power 3. Info, Factory
Fast Track Troubleshooting Manual
2010 Models
1. Select an active source signal. (HDMI preferred)
Test Pattern may rely on signal source to appear.
2. Access Service Mode
3. Access SVC
4. Access Test Patterns
5. Access Genoa-P
6. Check Test Patterns
7. If OK suspect input Source
8. Access Napoli
9. Check Test Patterns
10. If OK and Genoa-P was not good
Suspect Main Board or LVDS Cable
1.Check OSD & Customer Picture Test.
2. Access SVC Mode (with source signal)
3. Activate FBE Test Patterns & Verify.
4. Activate FRC Test Patterns & Verify.
FRC
FBE

4
ON SCREEN FAILURE EXAMPLES: ALIGNMENTS:
Fast Track Troubleshooting Manual
SPECIAL NOTES:
Inform customer of reset of all
Settings if Main Board or Panel is replaced.
1. Check/Set Option Bytes:
Green lines or a green screen
defective main board , LVDS , or
T-CON.
Pixelization can be caused by the main board
but is more commonly a source error
If Picture & Display errors
Defective Main Board, LVDS,
or T-CON
2. Check/Perform Firmware Upgrade for
all repairs.
3. Perform reset in Service Mode &
Plug and Play if Main board is replaced.
Vertical or Horizontal Lines :Defective
Panel likely but also T-CON, LVDS, or Main
Board. Use Test Patterns in Factory Service
Mode to determine error)
Option
Type Model Tuner Region DDR Light Effect Audio
AMP Ch Table Country Front Color Local Set Exhibition Mode
46A1UF0E UC6500 SEMCO - - OFF - - USA W-Violet - -
46D1UF0E UC6500 SEMCO - - OFF - - USA W-Violet - -
46A1UF0E UC6500 SEMCO - - OFF - - USA W-Violet - -
46A1UF0E UC6500 SEMCO - - OFF - - USA W-Violet - -
46L1UF0E UC6500 SEMCO -OFF -USA W-Violet
46A1UF0E UC6500 SEMCO - - OFF - - USA W-Violet - -
46L1UF0E UC6500 SEMCO -OFF -USA W-Violet
46D1UF0E UC6500 SEMCO - - OFF - - USA W-Violet - -