Samsung VC-7726VN User manual

VACUUM CLEANER
❈Before operating this unit, please read the instructions carefully.
Operating Instructions
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 1

1
This appliance must be connected to the same mains voltage as shown on the rating plate.
This vacuum cleaner is not suitable for removing any kind of liquid.
Carpets treated with a liquid cleaner must be allowed to dry before being cleaned with the unit.
Never operate the vacuum cleaner without a dust bag.
The cover cannot be closed if a dust bag is not inserted. Please do not close forcibly.
Keep children away from this vacuum cleaner. It must not be used on people or animals.
Never use your appliance to vacuum matches, glowing embers, or
cigarette-ends. Avoid vacuuming hard, pointed objects, since they may
damage the appliance or dust bag.
If your vacuum cleaner has a fault, please contact your electrical retailer or an authorized ser-
vice agent.
If the supply cord of this appliance is damaged, it must only be replaced by
a repair shop appointed by the manufacturer, because special purpose tools
are required.
Once you have unpacked the unit, do not simply throw the packing into the household waste.
Take them to the appropriate collecting points for recycling.









IMPORTANT SAFEGUARDS
PROTECTING THE ENVIRONMENT
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 2

2
IDENTIFICATION OF PARTS
HANDLE POWER CONTROL *
(ONLY HANDLE CONTROL TYPE) AIR REGULATOR *
SUCTION HOSE
DUST-FULL INDICATOR
CORD REWIND BUTTON
POWER CONTROL
SWITCH *
MITE KILLER LAMP *
ON / OFF SWITCH
HANDLE
TUBE *
CYCLONIC FILTER *
BUTTON FOR SUCTION
HOSE REMOVAL
FOR BLOWING
FLOOR NOZZLE *BUTTON FOR SUCTION HOSE REMOVAL
FOR USING THE MITE KILLER

Features marked * may vary according to model.
HANDLE CONTROL OPERATION (ONLY HANDLE CONTROL TYPE)
The suction capacity can be regulated steplessly by moving the side “A” to the desired position.
SLIDE IN THE STOP POSITION
Vacuum-cleaner switches off (stand by mode)
SLIDE TOWARDS MAX
Suction capacity increases steplessly up to max.
POWER CONTROL (ONLY SLIDING REGULATOR TYPE)
Vacuuming power can be adjusted to suit different situations using the power control.
MIN = For delicate fabrics, like curtains. MAX = For difficult floors and heavily soiled carpets.
RUG/FLOOR
SELECTOR
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 3

DUST-FULL INDICATOR
ASSEMBLING THE VACUUM-CLEANER SO THAT IT IS READY FOR USE
If the “Dust-Full” indicator switches to “RED” while you are cleaning, the dust bag requires
replacement.
NOTE: If the “Dust-Full” indicator continues to display “RED” even after changing the dust bag,
turn the cleaner off to see if the hose, tube or nozzle is clogged.
3
POWER CORD
1) PULLING OUT
The long power cord can be drawn out for
your convenience.
2) REWINDING
After disconnecting the plug from the electri-
cal outlet, press the cord rewind button lightly
with your toe. The cord will automatically
rewind.
NOTE: When removing the power cord from the electrical outlet, grasp the plug, not the cord.
ON/OFF SWITCH
You can start or stop your vacuum cleaner by
pressing the on/off switch lightly with your toe.
CORD REWIND
ON/OFF SWITCH
*OPZIONE 
1. Slide the free end of the extension wand into the nozzle tube.
2. Slide the narrow end of one extension wand into the other
extension wand.
3. Slide the extension wand into the handle end of the hose.
4. Slide the hose clamp into the suction inlet of the unit.
* Option ➀ Assemble the CYCLONIC FILTER with the handle
and extension wand(depending on model).
➁ Ajusting the telescopic tubes (depending on model).
➀➁ ➂➃*OPTION ➀
EXTENDING : Holding narrow
side of the telescopic tube with a
hand, pull the hadle to the oppo-
site side of it with another hand.
SHORTENING : Push the handle
to the narrow side
of the tube, hoding
it with another
hand.
*OPTION ➁
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 4

USING THE MITE KILLER (OPTIONAL)
Located on the rear side of the cleaner.
4
USING THE BLOWER (EXCEPT HANDLE CONTROL TYPE)
To blow out dust in crevices or corners you can use this function for your convenience.
1) Disconnect the body connector from the body
of the cleaner.
2) Shut the hose connection cover until tone is
heard.
• Your vacuum-cleaner is not malfuctioning if it
starts to operate when the hose connection
cover is closed. This will happen if the
vacuum-cleaner was on when the hose was
removed.
3) Mite killer lamp on.
Insect and germ killing work is started.
It will continue for 2 to 5min and the process
stops automatically.
MITE KILLER LAMP
HOSE CONNECTION COVER
1) Disconnect the hose clamper from the
body of the cleaner. 2) Open the tool storage cover.
3) Remove the blow hole cap from the
body of the cleaner. 4) Connect the hose clamper to the blow hole.
NOTE: Don’t use your vacuum-cleaner outdoors.
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 5

5
4) If you want to stop the machine while
operating, you can either
open hose connection cover, press
On/off button or unplug the plug.
USING THE ACCESSORIES
PARK POSITION
CREVICE
UPHOLSTERY DUSTING
CREVICE UPHOLSTERY
DUSTING DUSTING
• Before use, assemble the
dusting brush to the crevice
tool
Located in the top rear side of the
vacuum-cleaner, there is a nozzle support
that can be used to park the nozzle during
pauses in cleaning.
TRANSPORATING AND STORING THE VACUUM CLEANER
For easy storage and transportation, this
vacuum-cleaner has a clip system built into
the body, which will keep the tube, hose and
nozzle in a vertical position.
Press the tool storage cover downward.
❈Crevice tool for radiators, crevice, corners,
between cushions.
❈Upholstery brush for cushions and drapery.
❈Dusting brush for furniture, shelves, books, etc.
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 6

6
R EPLACING THE DUST BAG
FOR CLOTH FILTER BAG
NOTE: Used dust bag can be sealed by
removing the film from the paper
and sticking the latter over the suction
opening. (ONLY PAPER BAG)
After using, if the cloth filter bag is full of dust, clean the cloth filter bag and use it again.
1) To open the dust cover of the dust bag
compartment press the clamper upward
(The clamper is located at the front of the dust cover)
3) After removing the used dust bag, insert the
cardboard bag collar of the new dust bag
into the carrying bag.
2) Remove the carrying bag from the cleaner.
4) Press the dust cover down gently until the
clamper relocks.
CARRYING BAG
1) INLET-FILTER
❈Open the dust cover.
❈After detaching the filter, wash it lightly with
water, dry it in the shade, and then insert it in
its original position.
❈Close the dust cover.
GRILLE-FILTER
OUTLET-
FILTER
INLET-
FILTER
MAINTENANCE OR REPLACEMENT OF THE FILTERS
2) OUTLET-FILTER
❈The outlet-filter which the air comes out from the vacuum-cleaner.
❈Open the dust cover, and then pull the hook upward. (The hook is located at the front
of the dust cover)
❈Remove and replace the exhausted outlet-filter.
❈Close the grille filter, and then close the dust cover.
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 7

RUG/FLOOR SELECTOR
TROUBLE SHOOTING
Before use, make sure that the position of the selector button is in the right position for the type of surface to
be cleaned. ❈ In order to maintain best cleaning efficiency, clean floor brush using crevice tool after use.
PROBLEM CAUSE REMEDY
This Vacuum cleaner is approved the following.
Push to side ➀when cleaning
the carpets.
Push to side ➁when cleaning
the floor, tile, mat, etc.
You can use a dust bag in your cleaner for a long time thanks to the Cyclonic Filter system and it
maintain the maximum cleaning efficiency.
The larger particle of dust filtered from Cyclonic Filter remain in Dust Barrel when suctioned air
and dust revolves in the Cyclonic Filter. So the dust bag contains only smaller ones.
When the Dust Barrel is filled with dust up to the indicating line, it needs disposing and cleaning.
Dust Barrel can be cleaned in water.
1. Turn the Dust Barrel to the left and pull it.
2. Disconnect the Cyclonic Filter from extension wand and handle.
3. Remove thread and hair tangled around the net.
4. After cleaning the Dust Barrel and Cyclonic Filter, connect the Cyclonic Filter with extension
wand and handle(washed part should be dried in the shade throughly before assembling).
5. Push and turn the Dust Barrel to the right.
Adjust indicating marks each other carved on Dust Barrel and Cyclonic Filter.
DJ68-00079P REV(0.0)
➀➁
DUST BARREL
CYCLONIC FILTER
CREVICE TOOL
CYCLONIC FILTER
7
Motor does not start.
Suction force is gradually
decreasing.
Cord does not rewind fully.
No power supply.
Filter, nozzle, suction hose
or tube is blocked.
Check that the cord is not
twisted or wound unevenly.
Check cable, plug and socket.
Remove the object.
Pull the cord out 2~3m & push
down the cord rewind button.
N15490
DJ68-00079P(0.0) 4/23/02 8:54 PM Page 8