Samsung WA13R3Q3IW/YGG User manual

WA13R3Q3IW/YGG
WA15R3Q3IW/YGG
WASHING MACHINE CONTENTS
1. PRECAUTIONS FOR SAFETY DURING
SERVICING
2. TECHNICAL POINT
3. SCHEMATIC AND PCB DIAGRAM
4. HIGHLY IMPROVED STRUCTURE
5. TROUBLE DIAGNOSIS
6. HOW TO DISASSEMBLE
7. EXPLODED VIEW & PARTS LIST
WASHING MACHINE

13
3-1 SCHEMATIC DIAGRAM
3. SCHEMATIC AND PCB DIAGRAM
DC68-01913A

14
3-2 PCB - DIAGRAM
This Document can not be used without Samsung's authorization

27
6-1 REPLACEMENT OF MAIN PCB-ASS'Y
1) Remove the two cover-screw and then a screw 2EA as
showninthefigure
2) Lift up the CONTROL-PANEL by pushing it slightly
from right to left as shown in the figure here.
3) Turn the CONTROL-PANEL ASS'Y and remove 4EA
screws securing PCB ASS'Y.
4) Raise the ass'y gently to the direction to which the
screw are removed in order to separate the ass'y.
5) Disconnect the Wire Harness from ASS'Y PCB.
- Do not allow wire to get too much tension when
replacing control-panel.
- When assembling PCB, check if CONTROL-PANEL
fixing HOOK is properly positioned and tighten with
screws. (If not tightened exactly, Select S/W does
not operate.)
- Check the working condition of each parts (use test
mode)
6. HOW TO DISASSEMBLE

28
6-2 REPLACEMENT OF PRESSURE-SENSOR, WATER-VALVE, GUIDE-WATER, AND
CHECKER-ASS'Y
1) Remove 2 screws(rear part) securing TOP-
COVER, COVER-T.C, and remove them by lifting
COVER-T.C to the arrow direction.
2) PRESSURE-SENSOR
- After removing terminals of PRESSURE-SENSOR
LEAD-WIRE and disassemble by opening the HOOK wide .
* When reassembling PRESSURE-SENSOR, firstly
check AIR-HOSE position and connection status.
3) WATER-VALVE
- Remove 2 LEAD-WIRES of WATER-VALVE terminals.
Remove SCREW-TAP, TH 3EA securing WATER-
VALVE of ASS'Y-DETERGENT located inside the
TOP-COVER and then remove ASS'Y WATER-VALVE.
* Secure WATER-VALVE after checking if CAP- RING
is not missing. (without CAP-RING there may be
dangers of SHOT due to water leakage)
* ASS'Y is the one body of top-cover
4) When opening the LIC-TC, guide water can be
united until being in sight of screw.
5) Remove LEAD-WIRE of CHECKER-S/W and then
remove 2 screws securing CHECKER-S/W.
(Pressing the hook can open the lead-wires)
* How to release DOOR/UNBALANCE S/W
- When replacing defective wires, remove the switch
while holding down the (A) part. (It is not released
by pulling out the wire.)
WIRE
A
PUSHING

29
6-3 Replacement of CLUTCH ASS`Y
1) After removing CONTROL-PANEL
2) Remove COVER-SCREW 2EA(R
·
L) in CONTROL-PANEL
by using a pin and remove a SCREW 2EA(R
·
L) securing
CONTROL-PANEL by using a (+) driver and then remove
CONTROL-PANEL by pushing it slightly to left.
3) Remove screws (2EA in rear, 2EA in front) securing
TOP-COVER and remove SCREW securing EARTH
IRE and then lift TOP-COVER ASS`Y backward.
4) Remove 4 screws securing COVER-TUB and take
COVER-TUB out.
5) Remove PULSATOR-CAP by using a pin. After inserting
the (-) driver between the PULSATOR-CAP + PULSATOR,
disassemble by pushing it upward(
↑
).
※
Fix in the groove of
①
and assemble by pushing
②
.
6) Remove a bolt securing the PULSATOR using 10mm box
and lift it up.
7) Remove a nut securing ASS`Y SPIN BASKET and CLUTCH
by using a ZIG box and take ASS`Y SPIN BASKET out.
8) Lay down the washing machine so that the front of
OUT-CASE faces upward and remove 4 bolts securing
SADDLE by using a 10mm box.
※
Be careful not to cause damage or scratch to the washing
machine when you lay it down to the floor.
9) Remove BOLT 4EA securing CLUTCH by using a 10mm box
and take CLUTCH-ASS`Y out. (Check the CLUTCH status as
shown in the figure here.)
※
Assembling is in reverse order as disassembling.
Points to check after replacing ASS`Y CLUTCH
1) Check if TOOTH is joined by 3.5mm
∼
5.5mm, 2.0mm
∼
4.5mm
depth to the blades of SLEEVE while the washing is in operation.
(with Drain Motor OFF)
※
If the joining depth is not deep enough, there may be a problem
during washing.
2) Check if TOUCH maintains at least 1.5mm distance from the edge
of SLEEVE during spinning. (with Drain Motor OFF)
※
NUT unlock : clockwise
NUT lock : counter-clockwise
3.5~5.5mm(ENGAGING DISTANCE)
(The Condition During Washing)
OVER 1.0mm(ENGAGING DISTANCE)
(The Condition During Spining)
SADDLE
SADDLE
CLUTCH
MOTOR

30
7. EXPLODED VIEW & PARTS LIST
ASSY-COVER TOP
P0051
P0018
C0082
A0098
P0008
W0002
P0120
P0053
R0051
P0011
P0038
P0075
W0004

31
ASSY-TUB OUTER(SPIN BASKET)
U0131
U0225
U0100
U0076
M0053
U0262
U0258
X0003
U0196
U0195
S0050
F0045
R0009
S0035
S0049
S0032
U0075
U0136
W0001
H0028
U0199
U0177
S0030

32
ASSY-CASE OUTER
J0013
A0086
F0062
U0061
A0057
I0022
F0113
B0014
B0012
B0044
B0023

33
Parts List
NO. CODE NO. DESCRIPTION;SPECIFICATION QTY REMARK
A0057 DC61-10571B COVER-BACK;-,SBHG1-A,-,-,-,-,-,EDGE-BEND 1
A0086 DC61-20209P HANDLE;SW12E1SP,PP,-,-,-,-,SNOW/WHT,- 2
A0098 DC64-00748A INLAY-PANEL;WA16R3,PET,-,-,-,-,SELA-P/SP 1
B0012 DC97-00287A ASSY-BASE;SW12E1SP,PUMP 1WA13R3Q3IW
B0012 DC97-00287E ASSY-BASE;WA1635D0,PUMP(13KG) 1WA15R3Q3IW
B0014 DC61-30330A BASE;PP,SEW-X1,-, 1WA13R3Q3IW
B0014 DC61-30333A BASE;PP,SEW-X13,-, 1WA15R3Q3IW
B0023 DC91-11795D ASSY-LEG;SEW-D107,RUBBER-LEG+ADJUST 2
B0044 DC61-50164A LEG-LEVER;FRPP,SEW-X10,- 2
B0047 DC61-50166A LEG-RUBBER;BUTYL,10/12KG,D41(FRONT) 1
C0082 DC64-00697A PANEL-CONTROL;WA15R3W,ABS,-,-,-,-,SNOW-W 1
F0045 DC97-00252J ASSY-FILTER;WA11RAS3EG/XST,AG+RESIGN/SAV 1
F0062 DC99-00148A ASSY-PAINT;WA1334DODW,SNOW/WHT(PUMP) 1
F0113 DC61-50167A LEG-RUBBER;BUTYL,10KG/12KG,D29(BACK) 2
H0028 SCA-10RF43 ASSY-CLUTCH;SCA-10RF43(SEM-10TH KWANGJU) 1
I0022 DC97-00139C ASSY-HOSE DRAIN(O);SW65ASP2/SW55APP2,PUM 1
J0013 DC90-11190B ASSY-PUMP DRAIN;SW65ASP,220~240V/50Hz 1
M0053 DC60-50004A NUT-SPIN;-,ZNDC1,M24,-,-,L14,-,-,CW 1
P0008 DC96-00351E ASSY-CHECKER S/W;PM100C,STANDARD/CHINA 1
P0011 DC97-00885R ASSY-DETERGENT;WA1635D0,ABS(SNOW/WHT) 1
P0018 DC97-06662A ASSY-LID T.C;WA16R3Q3DW/XAP,T-PJT/SNOW-W 1
P0038 DC61-00105G CASE-DETERGENT;WA1635D0,ABS,-,-,-,SNOW-W 1
P0051 DC63-00484B COVER-T.C;WA13R3,ABS,-,-,-,-,BOSAN,SNOW- 1WA13R3Q3IW
P0051 DC63-00484M COVER-T.C;WA15R3,ABS,-,-,-,-,-,WHT,WA15R 1WA15R3Q3IW
P0053 DC63-00483A COVER-TOP;WA15R3W,ABS,-,-,-,-,-,SNOW-WHT 1
P0075 DC61-20175X HINGE-DOOR(L);SW10C1SP,POM,-,-,-,-,-,- 1
P0120 DC62-00024P VALVE-WATER;SEW-3G102J,PP,3PORT,MAX 10BA 1
R0009 DC66-40167B FLANGE-SHAFT;ALDC8,SEM-10T(10KG)6-WING,N 1WA13R3Q3IW
R0009 DC60-00023A FLANGE-SHAFT;PT-PJT,ALDC,-,-,-,-,-,- 1WA15R3Q3IW
R0051 DC67-00080J CAP-RINSE;SEW-3G100A,ABS,-,-,-,PEACOCK/G 1