Sana EUJ-702 User manual

User Manual
SANA OIL EXTRACTOR
EUJ-702
• Keep the user manual where you can find easily and read
“Important Safeguards” before using the product.
• This product is for home use (domestic use) and its
commercial and industrial use is prohibited.
Model

TABLE OF CONTENTS
  ..........................................................................................................................3
 ..........................................................................................................4
 .....................................................................................................5
  ...................................................................................................................................5
       ......................................................6
      .........................................................................6
  .......................................................................................................................7
   ..........................................................................................8
    ..............................................................................................9
  ....................................................................................................... 10
  ..................................................................................................... 12
 .................................................................................................. 14
 ........................................................................................................ 15
  ..................................................................................................... 16
 -  .................................................................................................. 19
     ......................................................................................................... 19
    ....................................................................................................20
 ............................................................................................................. 29

3
Read this first
Before using the Sana Oil Extractor, read the instruction manual carefully. It is
important for user safety, proper operation of the extractor, and avoiding damage
to the unit.
The Sana Oil Extractor is not a stand-alone device. It is designed as an attachment
for specific auger juicers. The list of suitable models is on page 6 of this manual. In
case of any doubts, please contact the seller. Attaching the extractor to a juicer not
approved may damage or destroy the unit and is not covered by the warranty.
The Sana Oil Extractor can be used to extract oil only from types of seeds and nuts
listed in this manual. Attempts to extract oil from materials other than those listed
here may lead to device failure and is not covered by the warranty.
During operation, the body of the press, especially the front cap, heats up
considerably. Touching these parts with bare hands may cause burns! Please
exercise great caution and always use the included protective silicon glove.
Due to the risk of damaging the motor, do not operate the oil extractor for longer
than 30 minutes. After this time, turn off the machine and let it rest for a minimum
of 2 hours.
Most of the parts of the Sana Oil Extractor are made of stainless steel, which makes
them relatively heavy. Dropping may cause serious damage or injury. Please be
careful when handling them.
Wash the parts of the Sana Oil Extractor (except for the mounting unit) before the
first use and always immediately after each use. Follow the instructions on page 15.
To ensure the highest quality of the Sana Oil Extractor, each unit is tested after
production. For this reason, it may contain trace amounts of seeds.

4
IMPORTANT SAFEGUARDS
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instructions concerning the use of the appliance
by a person responsible for their safety.
• The use of attachments not recommended or sold by the manufacturer may cause fire,
electric shock or injury.
• Before you start to extract oil, always select the appropriate size of regulating ring
depending on the type of seed. Please follow the instructions on page 8. Using the
wrong regulating ring may lead to a device malfunction.
• Always make sure the Sana Oil Extractor is assembled correctly before use.
• Be careful not to put your fingers or other objects into the openings of the device.
Do not use kitchen utensils (e.g. spoon, fork, knife, etx.) as a pusher. It may cause a
serious injury or damage the device. If material becomes lodged inside and blocks the
press, turn the motor o and disassemble the press to remove the blockage.
• Switch o the motor and disconnect from the power outlet before disassembling or
changing accessories.
• Never use a hammer or any other similar tools when disassembling the press. This
may cause damage not covered by the warranty.
• In case you encounter a problem with the press, always refer to the „Troubleshooting
Guide” in this manual (pages 16-18). If the solutions described there do not resolve the
problem, contact your dealer. Never attempt to repair the Sana Oil Extractor on your
own or at a non-approved service center.
• Do not use the Sana Oil Extractor if any part is damaged, or if the juicer motor is not
working properly or is damaged in any way.
• The Sana Oil Extractor is intended for household use only. Do not use it for anything
other than its intended use.

5
TECHNICAL SPECIFICATIONs
PARTs list
Parts and accessories in the box:
Product name: Sana Oil Extractor
Model: EUJ-702
Warranty: auger and regulating rings - 2 years
other elements - 5 years
Weight: 2kg
Dimensions: 16.5 cm (length) x ok. 19.5 cm (height) x 7cm (diameter)
1. front cap 1 pc
2. auger 1 pc
3. working tube 1 pc
4. mounting unit 1 pc
5. feeding tube 1 pc
6. funnel 1 pc
7. regulating rings 2 pcs
8. metal pin 1 pc
9. cleaning brush 1 pc
10. strainer 1 pc
11. protective glove 1 pc
12. oil pitcher 1 pc
2
5
3 41
7
6
8
9
12
10
11

6
JUICERS COMPATIBLE WITH the SANA OIL EXTRACTOR
Sana Oil Extractor is designed as an attachment for the following juicer models:
• Sana EUJ-707
• Sana EUJ-606
• Vidia SJ001
• Vidia SJ002
• Oscar DA-1000
• Oscar DA-1200
• Omega 8006(8226)
• Omega 8004(8224)
Do not use the Sana Oil Extractor with other devices not
specified on the list above. It may damage both appliances.
Nuts and seeds that can be processed
The Sana Oil Extractor is able to extract oil from the following seeds and nuts:
• flaxseed
• sesame seeds
• sunflower seeds
• pumpkin seeds
• rapeseeds
• primrose seeds
• hemp seeds
• black cumin
• poppy seed
• coconut shreds
• almonds
• walnuts
• hazelnuts
• peanuts
• pine nuts
• cashew nuts
• Brazil nuts
• pistachios
• macadamia nuts

7
CHOOSING SEEDS
• Always remember that the quantity and quality of the extracted oil depends greatly
on the quality of materials used. Low quality seeds have a lower oil content and will
have a reduced oil yield.
• Look for types of seeds with high oil content. Flax seeds are grown in many varieties.
The types grown for fiber generally don’t have a high oil content.
• No oil extractor is able to extract oil from dry seeds - if they are old, stale or
weathered. Look for seeds which are fresh and have been stored in appropriate
conditions for as short a period of time as possible.
• When starting your adventure with home oil extraction, try to buy the seeds from a
few dierent stores to try out their quality and oil content. This way you can find the
best places to purchase the hughest-quality seeds.
• Check the appearance of the seeds. Make sure they aren’t spoiled. Check for
discoloration or pests, such as insects or moths.
• Please note that the oil which is being extracted during press’s operation plays
an important role in its proper operation. It lubricates the auger, cools it down and
reduces friction. Processing seeds which lack oil can result in blockage of the auger.
• Some seeds and nuts require preliminary crushing before processing. You can do
this with a knife, blender or a special chopper. Remember, however, not to crush the
seeds too small. The size of the pieces should not be smaller than the size of a flax
seed and not greater than the size of a sunflower seed.

8
21
CHOOSING THE REGULATING RING
flaxseeds 1
sesame seeds 1
sunflower seeds 1
pumpkin seeds 1
rapeseeds 1
primrose seeds 2
hemp seeds 2
black cumin 1-2
poppy seeds 1
coconut shreds 2
almonds 2
walnuts 2
hazelnuts 2
peanuts 2
pine nuts 2
cashew nuts 1-2
Brazil nuts 2
pistachios 2
macadamia nuts 2
Produce ring #. Produce ring #.
Please note that sometimes you will need to use a dierent ring than what is
recommended above. For example, if a seed is too dry, it might be necessary to
use a smaller ring (with a lower number). On the other hand, if there is a problem
with blockage - use a bigger ring (higher number).

9
These seeds and nuts, in order to be pressed properly, should be crushed
to a smaller size. The size of the pieces should be bigger than a flaxseed or sesame
seed, but smaller than a sunflower seed. This could be done with the help of a knife,
blender or a vegetable chopper.
It is always best with all seeds and nuts to start with small quantities and feed them
sowly. But coconut need special caution. It need to be fed into the Sana Oil Extractor
very carefully, and in very small portions (teaspoon at a time). If inserted to the press
in larger amounts, the seeds may cause blockage and damage the parts. Always put
only a few seeds at a time to avoid blockage. If it still occurs, see the „Troubleshooting
guide“ section on page 18. (Problem 7).
PRODUCE WHICH NEEDS TO BE CRUSHED BEFORE PROCESSING:
PRODUCE WHICH HAVE TO BE FED VERY SLOWLY IN SMALL QUANTITIES:
• pumpkin seeds
• walnuts
• hazelnuts
• almonds
• peanuts
• cashew nuts
• brazil nuts
• macadamia nuts.
• coconut shreds
Don‘t blend seeds and nuts into a powder-like consistency. It will give poor yield
and can block the oil extractor.
SEEDS AND NUTS PREPARATION
SEEDS WHICH NEED TO BE SHELLED:
• pumpkin seeds
• sunflower seeds
• walnuts
• hazelnuts
• peanuts
The Sana Oil Extractor extracts oil only from seeds and nuts which are shelled.

10
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Place the working unit into the mounting
unit, so that their holes overlap.
Put the feeding tube into the overlapped
holes of both units. The marks on the
mounting unit and feeding tube should be
aligned.
Insert the auger into the working unit.
Slide it all the way in, until its end does not
protrude from the front of the working unit.
Depending on which seeds or nuts
you are going to process, choose the
proper regulating ring. Please refer to the
instructions provided on page 8. Put the
regulating ring into the front cap.
Place the front cap onto the working unit
and turn it clockwise several times until it is
fully tightened. Do not use excessive force.
Do not use the metal pin to do this.

11
STEP 6
STEP 7
STEP 8
STEP 9
Attach the assembled oil press to the motor
base of your juicer, the same way as you
attach a juicing unit. Turn the locking clip
clockwise to the „Close” position.
Place the funnel onto the feeding tube.
Put the oil pitcher with the strainer under the
working unit.
Place a husk container under the hole in the
front cap.
CAUTION: Processing seeds with the wrong regulating
ring may cause poor oil extraction or blockage.

12
OPERATING INSTRUCTIONS
STEP 1
STEP 2
STEP 3
STEP 4
Prepare the seeds or nuts to be processed.
Remember that some of them (e.g. pumpkin
seeds, nuts) need to be crushed into a
smaller size before you can put them into
the oil extractor. Refer to the instructions on
page 6.
Plug in the power cord. Press the „ON”
button on the motor base to start the motor.
Pour the seeds or nuts into the funnel.
The oil should start dripping after several
seconds. At the very start of processing, the
seeds may come out not fully crushed - this
is normal. The pressure in the press needs
to build up in order to extract the oil.
Please note that, depending on the type
and quality of the produce, the amount of
extracted oil and the extraction speed may
vary. From time to time, the grooves on the
working unit (where the oil comes out) may
need cleaning. To do that, simply brush
them with a cleaning brush a few times,
during proceessing.

13
DON’T PUSH Always feed in the produce slowly. Do not push it in. Never use a
pusher or any other object to force it down the feeding tube.
MAX 30 MIN Remember that the motor unit cannot operate continuously for
more than 30 minutes. Never let it work longer. Stop and let it cool down about 2
hours after 30 minutes of continuous use.
BE CAREFUL During operation, the working unit and the front cap of the oil
extractor get hot. Never touch it with your bare hands. Always use the included
protective silicon glove.

14
DISASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
STEP 6
STEP 7
STEP 8
STEP 9
STEP 10
STEP 3
STEP 5
STEP 4
Wait until the oil extractor finishes
processing the produce - when the oil
stops dripping and the funnel is empty.
Turn o the motor by pressing the „OFF”
switch and wait until it stops completely.
Turn o the motor again by pressing the
„OFF” switch. Wait until it stops and then
press and hold the „REV” button for 3-4
seconds. This will help to remove the auger.
Unplug the power cord from the outlet.
Remove the funnel and the feeding tube.
Caution! Use the protective glove to pull
out the auger and the working unit from the
mounting unit.
Turn the locking clip of the motor to the
„Open” position and remove the mounting
unit.
Put the metal pin through the holes in the
front cap, and rotate it counterclockwise.
This will loosen up the front cap.
Turn the motor back on for 4-5 seconds so
that the husks inside the working unit can
be expelled.
Caution! The front cap gets very hot. Use
the protective glove to unscrew it from the
working unit.

15
NEVER WASH THE MOUNTING UNIT The mounting unit of the oil extractor
cannot get wet. Never put it in water or splash water on it. The water can cause
the bearing, which is inside the mounting unit, to rust.
DON’T HIT Do not hit the parts with a hammer or any other hard tools. It may
cause deformation or damage of the oil extractor.
CLEANING INSTRUCTIONS
• Cleaning of the oil extractor parts needs to be done immediately after each use, when
the remains of oil and seed pressings are still fresh and easy to clean.
• The following parts should be cleaned in warm, soapy water: auger, front cap, working
unit, feeding tube, funnel, regulating rings and oil pitcher. Use dish soap or other
gentle detergent. Dry the parts using a soft cloth or a paper towel.
• Remember to never wash the extractor‘s mounting unit. The mounting unit of the oil
extractor cannot get wet. Never put it in water or splash water on it. The water can
cause the bearing, which is inside the mounting unit, to rust.
ATTENTION! THE Sana Oil Extractor parts should not be
assembled if they are wet. Wait for the parts to dry
completely before ASSEMBLING AND OPERATIng THE OIL
EXTRACTOR.

16
TROUBLESHOOTING GUIDE
PROBLEM 1
PROBLEM 2
1. Are the grooves on the working unit unobstructed? From time to time, it may be
necessary to clean the grooves during the oil extracting process. For that purpose,
there is a special cleaning brush included in the Sana Oil Extractor set. In case you
notice that the oil is running slower than before, or isn‘t running at all, clean the grooves
using the provided brush.
2. Please note that some seeds, especially nuts or dried coconut shreds, give little oil
while being pressed. This is normal, as these kinds of materials are far less oily than
produce such as flaxseed or sesame seeds (of good quality).
3. Perhaps the seeds you are trying to extract oil from are too old and dry inside (there is
very little oil left inside of them). Buy your seeds somewhere else, until you find a good
source. For details on this topic, see page 7.
1. Check whether a proper regulating ring has been used for processing the particular
type of seeds or nuts. For every type of nut or seed there is a recommended regulating
ring - for details see page 7.
2. Check whether the oil extractor has been properly assembled. If you’re not sure,
disassemble the machine and reassemble it while carefully following the instructions
from page 9.
3. If the machine has been properly assembled according to the instructions, and the
oil still isn‘t running, there is a high possibility that the material you are trying to press
is too dry inside. Unfortunately, there is always the chance of purchasing low-quality
seeds in shops. Don‘t be disheartened by this. Try buying your supplies somewhere
else until you find a good source. For details on this topic, see page 6.
4. From time to time, it might be necessary to clean the grooves during the oil extracting
process. For that purpose there is a special cleaning brush included in the set. In case
you notice that the oil is running slower than before, or isn‘t running at all, try cleaning
the grooves using the brush.
The oil is running very slowly or is not dripping at all.
The oil isn‘t running, even though the seeds are being collected and
processed by the extractor. The pressings are coming out of the
extractor through its front cap like they should.

17
PROBLEM 3
PROBLEM 4
PROBLEM 5
PROBLEM 5
1. If you are attempting to extract oil from pumpkin seeds or nuts, maybe you haven’t
crushed them suciently enough, or a bigger piece had blocked the press. Switch
the motor into reverse mode for 2-3 seconds. Wait until you hear it stop, then switch it
on again and see if the problem has been solved. It may be necessary to repeat this
step 2-3 times. If you tried this and the machine still isn‘t working, try disassembling the
press and cleaning out any seeds or husks from the auger and working unit. Assemble
the press once again and make sure the produce has been prepared for extraction
according to the guidelines from page 9. Remember that some materials require
crushing or removing their husks.
1. Check whether correct regulating ring has been used. Every kind of seed and nut
which can be extracted in the Sana Oil Extractor has a recommended regulating ring to
use during the extraction process - for more details see page 8.
2. Check whether the extractor has been assembled properly. In case of doubt,
disassemble the machine and then put it back together while carefully following the
instructions from page 10.
1. Check whether the auger has been properly inserted into the working and mounting
units. If properly assembled, the auger‘s end should be fully mounted in the juicer‘s
hexagonal slot. If not, disassemble the extractor and assemble it once again according
to the instructions on pages 10-11.
1. Some amount of squeaking is normal when extracting flax seeds. The squeaking
should disappear after a couple of minutes or during the next extraction
2. If the squeaking doesn‘t disappear, check if the proper regulating ring has been used.
For instructions see page 8.
The oil isn‘t coming out, the seeds are not going in, and the
pressings aren‘t coming out the extractor.
The oil is not dripping and the pressings coming out of the
extractor‘s front cap are not suciently dry or crushed.
The motor is working but the auger isn‘t rotating.
There is a loud squeaking noise during the oil extraction process.

18
PROBLEM 7
1. What kind of seeds were being processed in the oil extractor when the motor stopped?
If you were extracting oil from coconut shred or fennel flower, make sure you didn‘t put
too many seeds into the extractor. If this is not the case, make sure that you used the
proper regulating ring. The above-mentioned types of seeds should be pressed only
using regulating ring #2. Also, the seeds should be put into the extractor slowly and
in very small portions (to learn more about each seed‘s requirements, see page 9). If
you didn‘t follow the above-mentioned guidelines, disassemble the Sana oil extractor.
Make sure to clean out the inside of the press - especially the auger and the working
unit. After emptying the press, assemble it once again with the correct regulating ring.
Remember to insert seeds slowly and in small portions.
2. It is possible that a small object (e.g. a stone or a shell) has fallen into the oil extractor
through the feeding tube. To check and remove such objects, disassemble the Sana
Oil Extractor and clean the auger, feeding tube and working unit. Reassemble the
extractor and make sure to check your seeds for any foreign objects. Remember that
nuts and seeds can be extracted only after removing their husks (to learn more about
seeds see page 9).
3. Check whether the oil extractor has been properly assembled. If you are not sure,
disassemble it and put it together once again according to the instructions on
page 10.
4. Are you sure you are trying to extract oil from a material which is suitable for pressing in
the Sana Oil Extractor? Make sure to check the list of acceptable materials to extract oil
from on page 6. Never put any materials which are not on the list into the oil extractor.
5. Check whether the motor works. Disassemble the Sana Oil Extractor from the motor,
then switch the motor on. If it works well it means the problem lies within the oil
extractor. If you encounter problems with the motor, it may be the case that the unit is
overheated or it is suering from a malfunction.
6. Perhaps the motor has been overheated, and the thermal safety switch has
been activated. Remember that the motor which drives the oil extractor can work
continuously for a maximum of 30 minutes. After this time period, the machine has to
be switched o in order for it to cool down.
The motor has stopped working during the oil extraction.