Sangoma B700 FlexBRI User manual

INSTALLATION MANUAL
B700
FlexBRI

A) Ensure you are grounded.
(i.e., Touch unpainted metal to avoid destroying a computer
with electrostatic discharge, work on non-carpeted areas, etc.)
B) Carefully remove card and components from packaging.
Install your choice of supported software.
(e.g., Asterisk®, FreeSWITCH, Yate, CallWeaver, etc.)
See the list of compatible software at:
http://www.sangoma.com/products_and_solutions/compatible_software
Thank you for purchasing the Sangoma B700 FlexBRI card!
Please follow these instructions to begin using your new card.
2. INSTALL YOUR HARDWARE
1. INSTALL YOUR PBX SOFTWARE
Server
B700 FlexBRI Full product specications available at SANGOMA.COM
BRI Module(s)
Y-cable(s)
Red = TE Mode Green = NT Mode
TE MODE
NT MODE
Analog Module
or
FXO
FXO-2
FXS
TE MODE NT MODE
FXO-2
>BRI< >BRI< >FXO/FXS<
ON
1 2
SW3
D2
D1
D3
D4
D5
D6
ON
1 2
SW4
ON
1 2
SW1
ON
1 2
SW2
Termination
Resistors
TE = Off
NT = On
Power Feeder
for NT mode**
B700 BRI Card
Molex Power
Connector*
Full-height Bracket
Optional half-height
bracket included Optional Echo
Cancellation Module
Jumper Pins†

FXO-2
PORTS 1& 2
PORTS 3& 4
PORT 5& 6
TE MODE
NT MODE
>BRI<
>BRI<
>FXO/FXS<
ON
1 2
ON
1 2
ON
1 2
ON
1 2
SW2
SW1
SW4
SW3


SW 1& 2
SW 1& 2
SW 3& 4
SW 3& 4
SW 5& 6
SW 5& 6
ON
1 2
ON
1 2
ON
1 2
ON
1 2
ON
1 2
ON
1 2
TE MODE
NT MODE
TE MODE
SW2
SW1
SW4
SW3
SW6
SW5
TE MODE
NT MODE
D) Insert the Modules.
Insert the reversible, color-coded BRI modules in the shown
slots. The selected mode should face outward and be
readable through the “windows” on the daughter card.
Insert the FXO or FXS module into the analog slot.
* When using FXS, you must attach a Molex Power Connector from your
computer’s power supply unit. This is also recommended when using FXO,
but it is not necessary.
** If you plan to use BRI phones, you must also connect a standard power
supply to the Power Feeder.
E) Set Termination Resistors. (Use a paperclip or pen.)
When running in TE mode, ensure both termination resistors
that correspond to the module are set to OFF.(See SW1 in diagram.)
When running in NT mode, ensure both termination resistors
that correspond to the module are set to ON. (See SW2 in diagram.)
You must switch all termination resistors that correspond to
each module.
C) Determine which BRI ports you wish to run in TE Mode or NT Mode.
See diagram below for the corresponding ports and module slots.
Red = TE Mode
Green = NT Mode
Full product specications available at SANGOMA.COM
BRI Line 2
(2B+1D)
Port N+1 Port N
BRI Line 1
(2B+1D)
FXS
Power Feeder
for NT mode**

F) Insert the card into an open PCI or PCIe slot in server.
Fasten PCI bracket to chassis.
Server
PCI/PCIe Slots
Technical specications available at WIKI.SANGOMA.COM
Visit wiki.sangoma.com for the latest drivers and instructions.
You're done! Enjoy your new card.
3. INSTALL THE DRIVERS (WANPIPE®CD)

New Sangoma B-Series hardware comes with a 5-year warranty for
replacement and repair from the date of purchase.
This includes a no-questions-asked 30-day money back guarantee, Sangoma's renowned
free technical support, and free replacement in the unlikely event of a defect.
IMPORTANT – To qualify for the warranty, the end user must:
Register this product online at: http://www.sangoma.com/warranty/register/
Be able to prove point of purchase. To qualify for warranty protection, the product must
have been purchased from an Empowered by Sangoma partner.
The FlexBRI card contains Crash-proof Field Upgradable Firmware.
This means your B700 card has TWO (2) Firmware ash devices.
During card ashing, the new rmware is stored into the primary ash device.
If the machine crashes during card ashing and causes the primary ash device to
become corrupted, the secondary ash device can be selected to boot the card.
This will allow you to re-ash the primary device again.
In order to select the secondary ash device:
1. Shut down the machine and take out the B700 card.
2. Enter rmware recovery mode by connecting the two jumper pins on the upper
rear of the card.†
3. Restart the machine with rmware recovery jumper set.
4. Proceed to re-ash the card.
5. Once re-ashing is completed, shut down the machine and remove jumper.
6. Restart the machine.
If you are unsure of how to upgrade your rmware/ash, detailed instructions are provided on
wiki.sangoma.com.
5-YEAR WARRANTY
BOOT CARD WITH FIRMWARE RECOVERY JUMPER SET

CONTACT US
INTERNATIONAL [phone] EMAIL [email protected]
TOLL FREE IN N. AMERICA 1 800 388 2475 WIKI wiki.sangoma.com
Let us know whether this manual was helpful — your feedback is appreciated!