SANHO HyperDrive SPACE User manual

Getting Started
Thank you for purchasing the HyperDrive SPACE Memory Card
Backup Device. In your hand is the most advanced memory card
backup and portable storage device with currently the world's
fastest card backup and USB transfer speed, the longest battery
performance in its class and a reliable system that can safely store
and manage all your precious photos and digital content.
Please read this manual carefully before using the product to
ensure proper operation.
Kindly inspect the contents of the package and contact your local
dealer if there are any missing items or defects. Included in the
package are the following items:
HyperDrive SPACE Memory Card Backup Device
USB cable
AC power adapter
Car charger
Screwdriver
Instruction manual
Carrying case
The HyperDrive SPACE is available both with and without an
internal hard drive. Please check with your local dealer if your unit
already comes installed with a hard drive. The HyperDrive requires
a hard drive to operate.
Your local dealer may be able to help you to install the hard drive.
You can also purchase and install your own hard drive, as
recommended by your local dealer.
The information contained within this manual is correct at the time
of printing. Due to continual improvements being made to our
product, you are advised to visit our website or check with your
local dealer for the latest information and updates.

CAUTION!CAUTION!
Safety Instructions
Using inappropriate batteries in the HyperDrive may prevent it
from functioning normally and may even damage the product.
Please use only the provided battery or batteries from HyperDrive
authorized sources.
Please observe the correct polarity when inserting the battery. A
wrongly inserted battery may prevent the HyperDrive from
functioning normally. Serious damage may occur if the battery is
short-circuited and may even result in fire.
Use only the provided AC adapter or car adapter. Use of other
adapters or chargers with electrical ratings outside that of the
HyperDrive operating requirements run the risk of electric shock,
property damage or personal injury.
If the HyperDrive emits any burnt smell, excessive heat or smoke
during battery charging, turn off the power supply immediately and
contact your local dealer. Be careful when removing the battery as
the battery may be very hot.
Do not operate the Hyperdrive in wet or moist environments and do
not operate the HyperDrive with wet hands. If water enters the
HyperDrive, immediately remove the batteries and return the
HyperDrive to your local dealer for inspection. Do not use the unit
as there is a danger of short-circuit resulting in fire.

Table Of Contents
Instructions 1
Basic
Battery Charging (via USB) 2
Battery Charging (via AC Power) 3
Turning on HyperDrive 4
Auto Start HyperDrive 4
Turning off HyperDrive 5
Formatting Hard Drive 6
Copy Memory Card to HyperDrive 7
Error Handling During Copy 8
Setup
Date & Time 10
Folder Name 11
Backup Time Stamping 11
Transfer Speed 12
Verification 13
Hard Drive Mode 14
Startup 14
Advance
Erase Memory Card 15
Restore Factory Settings 16
Check Remaining Hard Drive Space 16
Browse/Delete Files/Folder 17
Copy Files/Folders back to Memory Card 18
Connecting HyperDrive to Computer via USB 19
Safely Disconnecting HyperDrive from USB 20
Maximizing Memory Card Backup Speed 21
Hard Drive Installation/Replacement 22
Battery Installation/Replacement 23
Specifications 24

USB Socket
LED Status Indicator
1
DC Power Socket
AUX Socket
(currently not in use)
SD/MMC/xD Slot
MS/MS Duo Slot
Keypad
Instructions
CompactFlash,MicroDrive Slot

使用前的准备
Without turning on the HyperDrive, plug in the USB cable into the
USB socket on the HyperDrive (as shown in diagram) and connect
the other end to your computer or a compatible USB power source.
When connected via USB, the HyperDrive will charged at 5V,
500mA.
You will see the following display screen when battery charging is
in progress.
Battery Charging (via USB)
2
Note:
You can still charge the battery via USB when the unit is turned on, but
you will not see the above battery charging display screen. Charging
will automatically stop when the battery is full.

Without turning on the HyperDrive, plug in the AC adapter to the
DC socket on the HyperDrive (as shown in diagram). When
connected via DC, the HyperDrive will be charged at 5V, 1A.
Battery Charging (via AC power)
You will see the following display screen when battery charging is
in progress.
Note:
You can still charge the battery via AC adapter when the unit is turned
on, but you will not see the above battery charging display screen.
Charging will automatically stop when the battery is full.
3
02:42:0202:42:02
00:00:0100:00:01

Turning on HyperDrive
When inserting any type of memory card or microdrive, the
Hyperdrive will auto switch on.
Auto Start HyperDrive
4
Press the button for 1 second, You will see the following
startup screen and then the Main Menu:
Note:
If the HyperDrive was turn on automatically by memory card
insertion, removal of the memory card will also automatically turn off
the HyperDrive.

Turning off HyperDrive
From the Main Menu, press the button to turn off the
HyperDrive.
From any screen, you can also press the button continuously for
5 s to turn off the HyperDrive.
5
CAUTION!
Ensure that all memory cards are removed from
the HyperDrive, otherwise the HyperDrive will
not be able to shut down completely and will
continue to consume a small amount of battery
power. If the card remains in the unit, the
battery may be exhausted in a week's time.

The HyperDrive can only operate with FAT32 formatted hard
drive.If your hard disk is brand new or not in FAT32 format,you will
need to follow the steps below to format the hard drive.
CAUTION!
Formatting the hard drive will delete all the
data on the hard drive including the
partitions. Please ensure that the hard drive
does not have any data that you may require.
Formatting Hard Drive
6
Select Feature->Advance->Format:
149.05GB,ST9160821A149.05GB,ST9160821A
149.05GB,ST9160821A149.05GB,ST9160821A
149.05GB,ST9160821A149.05GB,ST9160821A

Copy Memory Card to HyperDrive
Insert the memory card and on the Main Menu, select Copy:
正在拷贝
使用前的准备
7
\SANH0000.SPC\SANH0000.SPC
\SANH0000.SPC\SANH0000.SPC
100100
276276 968.3MB968.3MB
00005511
967.6MB,Sanho Flash967.6MB,Sanho Flash
\SANH0000.SPC\SANH0000.SPC
100100
276276 968.3MB968.3MB
00005511
Copy Progress Bar Destination Folder
Copy Time Elapsed
No. Of files transferred
Total Size Transferred

If a critical error (e.g. insufficient hard drive space, low battery
etc.) occurs during the memory card copy process, the HyperDrive
will cease copying and display an error message. At the same time,
the LED indicator will blink yellow.
\SANH0000.SPC\SANH0000.SPC
Error Message
8
Error Handling During Copy
During then, you have 2 minutes to press to clear the error
message, otherwise the HyperDrive will shut down and the error
message will appear again the next time you turn on the unit.
5252 216.7MB216.7MB
Previous
Error Message
No. Of Files
Already Transferred
Size Of Files
Already Transferred

Error Handling During Copy
If a non-critical error (e.g. file error or bad sector on the memory
card) occurs, the HyperDrive will cease copy and allow you to
either cancel the copy or skip to the next file. If you press , the
HyperDrive will skip the error file and continue to copy the rest of
the memory card. As a safety precaution, the HyperDrive will also
now copy at the most conservative (normal) speed to ensure
maximum memory card compatibility and that all the files are
safely retrieved.
9
IMG00053.JPGIMG00053.JPG
\SANH0000.SPC\SANH0000.SPC
\SANH0000.SPC\SANH0000.SPC
5252 216.7MB216.7MB 2222
IMG00053.JPGIMG00053.JPG
5353 218.1MB218.1MB 2222
IMG00054.JPGIMG00054.JPG
\SANH0000.SPC\SANH0000.SPC
Error File
Skip to next file and
continue copying
Cancel Copy Process
This is a very useful feature as it will allow you to retrieve the rest
of the data on the memory card even if the memory card is
defective or damaged.
Do note that the error file may still show up on the
HyperDrive hard drive but it will most likely be corrupted.
The rest of the files will not be affected.

使用前的准备
10
Date & Time Setup
You may set the date and time according to the following steps.
S e l e c t S e t u p - > S y s t e m - > T i m e :
1717
0909
20062006
1010
2929

The HyperDrive will create a new folder in the root directory of the
hard drive during each backup process. All the data from the
memory card will be downloaded into this folder. By default, the
new folders will be named SPACEXXX (where XXX will be a
sequential number running from 000 to 999). Alternatively you can
define your own 8 character folder name as per the following steps.
Folder Name Setup
使用前的准备
11
Select Setup->Name:
SPACE000SPACE000
Backup Time Stamping
HyperDrive is also able to name the folder according to the current
time when the folder is created in the format of YYMMDDHH.mms
(Year/Month/Day/Hour/minute/second)

12
Transfer Speed Setup
Select Setup->Speed:
Hyper Speed:
Designed for SanDisk Extreme III and Extreme IV CF cards, able to
achieve the maximum transfer speed of 20MB/s.
Ultra Speed:
Designed for professional series CF cards, able to achieve a
maximum transfer speed of 16MB/s.
High Speed:
Designed for majority of CF cards, able to achieve a maximum
transfer speed of 12MB/s.
Normal Speed:
Suitable for all type of memory cards and guaranteed maximum
compatibility.

13
Verification Setup
Full Verification:
After each file copy, the file on the HyperDrive hard drive is
compared bit by bit with the same file on the memory card to
ensure that the data is identical and successfully transferred. This
is the slowest but most accurate verification process.
Quick verification:
This is the fastest verification process as it only verifies 1 out of
every 32 sectors of data.
Random verification:
This process will carry out full verification on one out of several (3
or 7 or 16) files. By default, it will verify 1 out of every 7 files.
Select Setup->Verify:

Hard Drive Mode Setup
Startup Setup
You can select the function that the HyperDrive automatically
performs during startup (i.e. when it is turn on).
使用前的准备
14
Select Setup->System->LBAMode:
S e l e c t S e t u p - > S y s t e m - > S t a r t u p :
48Bits LBA(Logical Block Address):
Select this for large hard drive (over 128GB) support. Do not use
this mode for smaller hard drives (128GB & below) as they may
perform slower and have compatibility issues.
28Bits LBA:
Select this for smaller hard drive (l28GB & below) support.
Enter Main Menu
(default)
Automatically backup
from memory card if
present Displays remaining
hard drive space

Erase Memory Card
15
S e l e c t F e a t u r e - > A d v a n c e - > E r a s e :
This feature will erase/delete all the data that is on the memory
card.
Note:
The Hyperdrive is not able to delete any files from memory cards with
FAT12 format.

Restore Factory Settings
This function will restore the HyperDrive to factory settings.
S e l e c t F e a t u r e - > A d v a n c e - > R e s e t :
Check Remaining Hard Drive Space
142.2GB142.2GB
76.6GB76.6GB
Select Feature->Browser->HDDSpace:
16

Browse/Delete Files/Folders
To b r o w s e Ha r d Dr i ve , s e l e c t F e a t u r e - > B r o w s e r - > H D D :
SANH0006.SPC\SANH0006.SPC\
SANH0007.SPC\SANH0007.SPC\
SANH0008.SPC\SANH0008.SPC\
My Document\My Document\
HD Space.txtHD Space.txt
2/22/2
100EOS1D\100EOS1D\
1/11/1
^^
^^
DCIM\DCIM\
1/11/1
XN3H0124.CR2XN3H0124.CR2
XN3H0125.CR2XN3H0125.CR2
XN3H0126.CR2XN3H0126.CR2
XN3H0127.CR2XN3H0127.CR2
1/191/19
^^
XN3H0128.CR2XN3H0128.CR2
\SANH008.SPC\DCIM\100EOS1D\XN3H0\SANH008.SPC\DCIM\100EOS1D\XN3H0
125.CR2125.CR2
17864Kbytes17864Kbytes
May.13,2006 12:52:00May.13,2006 12:52:00
\SANH008.SPC\DCIM\100EOS1D\XN3H0\SANH008.SPC\DCIM\100EOS1D\XN3H0
125.CR2125.CR2
17864Kbytes17864Kbytes
XN3H0124.CR2XN3H0124.CR2
XN3H0126.CR2XN3H0126.CR2
XN3H0127.CR2XN3H0127.CR2
XN3H0128.CR2XN3H0128.CR2
1/191/19
^^
XN3H0129.CR2XN3H0129.CR2
Press
Press
Press
Press
Press
17