Sanji ZX30 User manual

ZX30-USER-REV0
ZX30 USER INSTRUCTIONS
Briefed with the idea of “The Super intelligent Design Concept”
Sanji engineers developed the ZX30 Range of professional
vehicle security alarm systems. The ZX30 represents the 'state
of the art' in vehicle security. Read these instructions for correct
system operation. All points marked are optional features.
1) SETTING THE
ALARM To enable the
full alarm
features.
Press the lock button on the
vehicles remote, the unit
will sound 2 soft chirps. The
doors will lock.
2) DOOR / BOOT /
BONNET OPEN
WARNING
To warn the
driver that a
door or boot
is open when
setting the
alarm.
The unit will sound two
additional loud chirps and flash
the indicators twice when
setting the alarm. If a door is
still open when the unit fully
arms, the doors will be
bypassed. The system will
assume a faulty door switch.
3) ALARM DELAY
PERIOD 15 second
arming delay. The dash led will flash rapidly
during the 15 second delay
period. After the delay, the dash
led will start to flash slowly. The
alarm is now fully armed.
*
dash led
flashing
rapidly
4) SENSOR SHUT
DOWN To disable the
interior sensor
so that a pet
or person can
remain inside
the vehicle
when the
alarm is set.
Set the alarm and wave your
hand in front of the sensor. The
siren will sound 4 chirps. The
sensor has now been disabled.
When the alarm is set the doors
and ignition will armed but the
sensor will be disabled. When the
alarm is set again the sensor will
be armed.
5) RESETTING
THE ALARM To reset the
alarm. Press the unlock button on the
vehicles remote. The unit will
sound 1 soft chirp and the doors
will unlock. The alarm has now
been reset.
6) AUTO ZONE
BYPASS
7) VIOLATION
CHIRPS
Auto-
matically
bypass a
defective
zone.
To indicate to
user that the
alarm has
triggered
in his/her
absence.
If the unit detects a permanently
faulty zone, e.g. door or sensor
during alarm set, the system will
sound 3 times then isolate
the faulty zone.
When the alarm is reset, the
unit will sound 4 loud chirps
if the alarm had triggered during
the alarm set mode.
8) DOOR LOCK
ON START Automatic
locking of all
doors when
ignition is
turned on.
When the ignition is turned on, if
all the doors, boot and bonnet
are closed, the doors will lock.
*
9) ONE EVENT
OVERRIDE To override
the alarm, in
the event of a
flat remote
battery.
Open the door, the alarm will start
to sound the siren. Turn the Ignition
on unit chirps once, the system will
be reset. This is a once off override.
10) PERMANENT
SERVICE
MODE
To disable the
alarm
permanently.
In drive, (ignition on), press the
hidden override button for
+- 5seconds, the siren will chirp
4 times. Permanent override has
been activated. The dash led will
be on. All alarm, immobilizer and
hi-jack features will be disabled.
When the ignition is turned on the
unit will flash the indicators rapidly
for 4 seconds to warn the user
that the unit is in service mode.
To exit service mode, turn the
ignition on and press the hidden
override button for +- 5seconds,
the siren will chirp twice.
The permanent override for the
alarm will be deactivated. The
dash led will be off. The system
will be fully functional again.
12) DRIVER’S
DOOR
HI-JACK
To activate
hi-jack. In drive open then close driver’s
door. If all doors, bonnet and
boot are closed the dash led will
give a 1 second pulse. The unit
has entered hi-jack phase.
*
To reset the
unit back to
normal drive
mode.
15) RESETTING
HI-JACK
*
Press the hidden push button at
any time for +/- 2 seconds, the
unit will chirp once to confirm
that hi-jack has been reset.
13) HI-JACK
OPERATION Hi-jack mode. Countdown period is 90 sec. If
ignition is turned off during this
time, the timer will stop. When
the ignition is turned on again
the timer will continue. If you try
to set or reset the alarm during
the countdown period, the unit will
sound 4 loud chirps to warn you
that you are in hi-jack mode.
*
14) HI-JACK
WARNING
PERIOD
Hi-jack
warning
mode.
After the countdown period the
unit will enter the 20 second
warning period. The unit will
chirp and flash the indicators.
After this period the unit will
enter the 8 second slow down
period. At any point in time you
can reset hi-jack by pressing the
hidden button.
*
16) FINAL
HI-JACK To confirm
what phase
the unit is in.
*
In final hi-jack the siren will
sound on and off at 5 second
intervals and the indicators will
flash. The immobiliser will be
armed. The unit can be reset by
pushing the hidden button for
+/- 3 seconds.
service mode ON
5sec
service mode OFF
5sec
service mode
warning
11) FORCED
HI-JACK
MODE
Forced hi-jack
in drive.
*
When you start the vehicle, the
unit will enter hi-jack, the dash
led will give a 1 second pulse.
Refer to point 15 to reset hi-jack.
If you start the vehicle with the
hidden button pressed, the unit
will not enter forced hi-jack.