Sanyo Carrier 16LJ Series User manual

16LJ
Single-Effect Hot Water-Fired
Absorption Chillers
Nominal cooling capacity 264-1846 kW
50 Hz
GB/T-19001-2000 to ISO9001/2000
Installation instructions

The cover photograph is for illustrative purposes only, and are not contractually binding.
NOTES TO USERS
Thank you for purchasing a Sanyo/Carrier absorption chiller.
Refer to this manual and the specication drawings before installing the absorption chiller and read this manual carefully before
operating the unit. It contains instructions for the installation of the chiller.
Please utilize the chiller to its optimum performance by carrying out the recommended daily maintenance and handling
instructions as well as the periodic service.
If you need any information about maintenance contracts or have any other enquiries, please contact your Carrier service agent.

3
Exhibits
LA - Precautions for use................................................................................................................................................................ 24
LB - Shipping dimensions/Centre of gravity location............................................................................................................ 25-26
LC - Foundation dimensions......................................................................................................................................................... 27
LD - Not used
LE - Typical piping diagram/Water treatment/Dimensional drawings ............................................................................... 28-37
LF - Wire sizes/Field wiring/Wiring diagram ........................................................................................................................38-41
LG - Insulation area....................................................................................................................................................................... 42
LH - LiBr solution material safety data sheet........................................................................................................................ 43-45
LI - Character recognition table/operation board parameter verication..........................................................................46-49
LJ - Flow diagram and damper and valve position .................................................................................................................... 50
CONTENTS
1 - INSTALLATION ........................................................................................................................................................................ 4
1.1 - Environmental requirements and safety precautions................................................................................................................. 4
1.2 - Safe installation ......................................................................................................................................................................... 8
1.3 - Delivery inspection.................................................................................................................................................................... 8
1.4 - Rigging ...................................................................................................................................................................................... 9
1.5 - Moving the chiller ..................................................................................................................................................................... 9
1.6 - Placing the chiller on the foundation........................................................................................................................................ 9
1.7 - Levelling .................................................................................................................................................................................... 9
1.8 - Leak test and method of charging/removing nitrogen gas...................................................................................................... 10
1.9 - Piping....................................................................................................................................................................................... 12
1.10 - Field wiring............................................................................................................................................................................ 12
1.11 - Purging................................................................................................................................................................................... 12
1.12 - Insulation ............................................................................................................................................................................... 13
2 - TEST OPERATION ................................................................................................................................................................. 13
2.1 - External visual inspection....................................................................................................................................................... 13
2.2 - Solution charge........................................................................................................................................................................ 13
2.3 - Electrical check........................................................................................................................................................................ 13
2.4 - Initial control board setting...................................................................................................................................................... 14
2.5 - Damper setting and valve position .......................................................................................................................................... 14
2.6 - Purging..................................................................................................................................................................................... 14
2.7 - Function test ............................................................................................................................................................................ 15
2.8 - Operation ................................................................................................................................................................................ 16
3 - CHECK LIST ........................................................................................................................................................................... 19
3.1 - External visual inspection........................................................................................................................................................ 19
3.2 - Verify the eld wiring and wiring of palladium cell heater..................................................................................................... 19
3.3 - Check of motor insulation resistance....................................................................................................................................... 19
3.4 - Check of control board safety and switch settings .................................................................................................................. 20
3.5 - Check of purge pump............................................................................................................................................................... 20
3.6 - Verify auxiliary equipment ...................................................................................................................................................... 20
3.7 - Bubble test ............................................................................................................................................................................... 20
3.8 - Verify valve opening status and switch positions .................................................................................................................... 20
3.9 - Verify control board parameters .............................................................................................................................................. 21
3.10 - Pre operation checks.............................................................................................................................................................. 21
3.11 - Operation and data record...................................................................................................................................................... 22
3.12 - Sample of absorbent taken (for analysis) .............................................................................................................................. 23

4
1 - INSTALLATION
1.1 - Environmental requirements and safety
precautions
1.1.1 - Installation considerations
The 16LJ absorption chiller is designed for indoor installation
in a machine room. The protection rating of the chiller is IP40.
Room temperature should be maintained between 5°C and
40°C to protect against solution crystallization during chiller
shutdown. The humidity in the machine room must be kept
below 90%.
1.1.2 - Field wiring
CE machines should be connected to a power source that
complies with overvoltage category III (IEC 60664). All other
wiring should comply with overvoltage category II.
1.1.3 - Altitude
Please install the absorption chiller at a maximum height of
1000 m above sea level. If the location is higher than 1000 m
above sea level, please contact your local Carrier office.
1.1.4 - Safety precautions
• Before operating this chiller, first carefully read the
following instructions.
• All precautions are classified as either WARNING or
CAUTION.
WARNING: Failure to observe this instruction may result in
serious injury or death.
CAUTION : Failure to observe this instruction may cause an
injury or failure of chiller. Depending on circumstances, this
may result in serious injury or death.
This symbol denotes danger, a warning or a caution.
The illustration in this symbol shows the specic
description of the item.
This symbol prohibits an action.
The illustration next to this symbol shows the specific
description of the item.
This symbol instructs an action to be done.
The illustration in this symbol shows the specific
description of the item.
• After reading this manual, it should be kept in a safe place
to be available for any user at any time.
TURN OFF THE BREAKER BEFORE CLEANING AND
CHECKING
Always turn off the circuit breaker before cleaning and checking
the cooling tower fan, chilled water pump, or other components
linked to the chiller, to provide protection from electric shock or
or possible injury by the rotating fan.
INSPECTION
DO NOT TOUCH THE CONTROL PANEL SWITCH WITH
WET HANDS
Do not touch the switch inside the control panel with wet hands
to avoid electric shock.
STOP OPERATION IN CASE OF FIRE, EARTHQUAKE OR
ELECTRICAL STORMS
Stop operation in case of re, earthquake or an electrical storm, to
prevent re or electric shock.
DO NOT TOUCH THE WIRING INSIDE THE CONTROL
PANEL
Do not touch the wiring inside the control panel to avoid electric
shock.
SWITCH
DO NOT TOUCH
DO NOT TOUCH
DO NOT TOUCH HIGH-VOLTAGE CABLES
Do not touch high-voltage cables to avoid electric shock.
DO NOT TOUCH
MUST BE OBSERVED
1.1.4.1 Safety considerations
WARNINGS

5
DO NOT OPERATE THE CHILLER IF THERE IS A SMELL
OF GAS
Do not operate the chiller if there is a smell of gas. Do not turn
on/off any switch, as this could cause a re.
KEEP FLAMMABLE SUBSTANCES AWAY FROM THE
CHILLER
Do not place any ammable substances (e.g. gasoline, thinner)
close to chiller, ue, chimney or oil tank to prevent re.
DO NOT TOUCH ROTATING PARTS OF FANS
Keep away from rotating parts of fans or pumps to avoid possible
injury.
PROHIBITED
PROHIBITED
PROHIBITED
SOLVE ALL PROBLEMS BEFORE RESTARTING THE
CHILLER
Solve all the problems before restarting the chiller after a safety
or security device is activated, to prevent re.
MUST BE OBSERVED
DO NOT PLACE HEAVY OBJECTS ON THE CHILLER
OR CONTROL PANEL
Do not place heavy objects on the chiller or control panel as
these may fall off and cause injuries.
PROHIBITED
DO NOT CLIMB ON THE CHILLER
Do not climb on the chiller as you may fall off.
PROHIBITED
CALL SPECIALISTS FOR SERVICE OR MAINTENANCE
Call specialists for service or maintenance. Incorrect service/
maintenance may cause electric shock, re or burns.
MUST BE OBSERVED
AUTHORIZED PERSONNEL ONLY
A notice, "For Authorized Personnel Only" must be afxed to
the chiller to stop unauthorized personnel from touching it. If
necessary surround the chiller by a protective fence. Misuse of
the chiller may cause injury.
PROHIBITED
WARNINGS CAUTIONS

6
DO NOT POUR WATER ON THE CHILLER OR CONTROL
PANEL
Do not pour water on the chiller or control panel to avoid electric
shock.
PROHIBITED
USE THE CORRECT POWER SUPPLY
This is indicated on the chiller name plate. Use of an incorrect
power supply may cause re or electric shock.
PROHIBITED
NEVER CHANGE THE SET VALUES
Never change the set values of the safety and/or protective
devices. Wrong settings may damage the chiller or cause re.
PROHIBITED
STOP THE OPERATION WHEN COMBUSTION SMOKE IS
BLACK
Stop the operation when combustion smoke is black and call a
service engineer.
MUST BE OBSERVED
DO NOT TOUCH THE ABSORBENT
Do not touch spare or leaked absorbent, as this can cause metal
corrosion or skin disease.
PROHIBITED
OBSERVE THE SPECIFIED WATER PRESSURE
The specied chilled/hot water and cooling water pressure must
be strictly observed.
Incorrect pressure may cause the water to leak/spray which can
lead to short circuits or burns.
MUST BE OBSERVED
PROHIBITED
STOP THE PURGE PUMP TO REPLACE OIL
Stop the purge pump when replacing oil to avoid possible injury
by fuel spillage.
MUST BE OBSERVED
DO NOT TOUCH HIGH-TEMPERATURE AREAS
Do not touch high-temperature areas, as they may cause burns.
These areas are indicated by caution label.
What
voltage?
STOP
CAUTIONS

7
ONLY AUTHORIZED PERSONNEL SHOULD SERVICE
THE CHILLER
Only authorized personnel should service the chiller. Incorrect
service could result in electric shock or re.
PROHIBITED
1.1.4.2 - Safety precautions for repair, moving or disposal
ONLY AUTHORIZED PERSONNEL SHOULD REMOVE OR
REPAIR THE CHILLER
Any relocation or moving of the chiller should only be done by
authorized personnel. Incorrect work could result in water leaks,
electric shock or re.
MUST BE OBSERVED
ONLY AUTHORIZED PERSONNEL SHOULD DISPOSE OF
THE CHILLER
To dispose of the chiller, contact local specialists. Incorrect
disposal may result in absorbent leaks and cause metal corrosion
or skin disease, electric shock or re.
MUST BE OBSERVED
WARNINGS
CAUTIONS

8
1.2 - Safe installation
Equipment installation must be carried out by a qualied
installer, taking the appropriate safety measures.
Ensure that unauthorized people cannot enter the installation
site during installation.
1.3 - Delivery inspection
Upon delivery of the Carrier-Sanyo chiller to the job site, the
owner or his designated representative should carefully inspect
the chiller:
• Ensure that the chiller is factory-charged with nitrogen gas
to a pressure of 20 kPa.
• Open SV7 and connect a pressure gauge to SV2. Open
V2, V3 and B-valve, and check the pressure at the
pressure gauge. If the pressure is 0 kPa, the chiller has a
leak. In this case, check the leaking point with pressurized
nitrogen gas at 50 kPa. Close the cap of SV2 and SV7
with sealant.
• Refer to paragraph 1.8.2 (Fig. 5), exhibit LA and the
specication drawings.
Solution volume
16LJ Absorbent Refrigerant Alcohol Inhibitor
kg kg l l
11 430 60 0.78 0.25
12 430 60 0.78 0.25
13 560 100 1.02 0.33
14 620 90 1.12 0.36
21 750 110 1.36 0.44
22 810 120 1.48 0.48
23 980 150 1.78 0.57
24 1070 140 1.94 0.62
31 1230 190 2.24 0.72
32 1340 170 2.44 0.78
41 1560 250 2.84 0.91
42 1680 230 3.06 0.98
51 1950 260 3.54 1.13
52 2170 290 3.94 1.26
53 2420 310 4.40 1.40
Legend
Absorbent LiBr 50 wt %
Inhibitor Li2MoO420 wt % 300 ppm (total concentration)
Alcohol Octyle alcohol CH3(CH2)5CH(OH)CH3
• Check for physical damage to the chiller
- Main shell and piping
- Valves
- Control panel
- Wiring and connections
- Accessories
- Solution
• Check the shipping or packing slip sent with the chiller
and note all missing items.
• Check all boxes or crates shipped with the chiller for
missing items.
NOTES:
1. Isolation pads are not required for most installations.
2. Inform Carrier immediately if items are damaged or
missing.

9
1.4 - Rigging
Check the weight of the chiller by referring to the contract
specications and then choose and use suitable wires and
shackles. To lift the chiller use the four holes provided at the
corners of the lower tube sheet. Note that the angle of the wires
should be 60° maximum, as shown in the gure below. Refer to
the specication drawings and exhibit LB.
1.6 - Placing chiller on the foundation
Refer to the specication drawings and exhibit LC - Foundation. Set
the chiller on the foundation bolt positions.
1.7 - Levelling
• Fill a clear vinyl hose with water and check there are no
air bubbles in the hose.
• Using point A as reference point, measure the difference
in the water level at the other points (B, C and D).
A B
(Evaporator side)
(Absorber side)
C D
A B C D
0 mm ___ mm ___ mm ___ mm
• The levelling calculation is as shown below:
A-B C-D A-D B-C A-C B-D
L L L L W W
L: Chiller length
W: Chiller width
≤2
1000
Fig. 1
Evaporator
side
Absorber
side
Fig. 2
1.5 - Moving the chiller
If the chiller needs to be moved, use of a fork-lift truck is
recommended. The wire should be connected as shown in the
gure below.
• Note that in the gure below there are four levelling check
points on the chiller, labeled A, B, C and D. These check
points are designated by three punch markers on the tube
sheet or shell of the lower shell.
Tolerance

10
Charge N2gas Refer to 1.8.2
Perform recheck
Check at 50 kPa - - - Check leakages
OK Not good
Tighten nuts
Remove N2gas and repair - charge N2gas up to 50 kPa
Remove N2gas
Air purging
Test sequence
Procedure (see Fig. 5)
1. Confirm that V1, V2, V3, B-valve, SV1, SV2 are fully
closed.
2. Confirm that all absorbent and refrigerant pump isolation
valves are fully open.
3. Connect the vacuum gauge to SV2 and open SV2
- Charge N2gas (refer to 1.8.2).
- Pressurize the chiller up to 50 kPa with N2gas. The
pressure inside the chiller can be checked with the
vacuum gauge.
- When the pressure reaches 50 kPa, close the service
valve and the valve of the N2gas cylinder.
4. Check the following positions with the soapy water:
- All field-welded parts (not needed for one-piece
machine)
- Sight glass: If any leakage is observed in the sight
glass, tighten the fittings and ensure that there is no
N2gas leak.
- Flare nut joints of service valves.
- Flange connections (absorbent pumps, refrigerant
pump, etc.)
- Diaphragm valves.
5. If any leakage is observed at the welded parts, remove the
N2gas and then repair the leaks.
6. Repeat steps 3 and 4.
7. If there is no leakage at 50 kPa pressure, keep the chiller
pressurized to 50 kPa for 24 hours, and then check the
pressure again.
8. After completion of the test, remove the N2gas, and the
vacuum gauge (refer to chapter 1.8.3)
9. Close SV2.
NOTE: If N2gas is removed, ensure that the room is
sufciently ventilated.
Spacer position
Spacer position
• If tolerances are not met, shim the appropriate points by
inserting a metal spacer between the machine base and
the foundation. The metal spacer size is approximately 50
mm wide by 80 mm long. Prepare spacers with different
thicknesses (0.6 mm to 9 mm).
Fixing of the anchor bolts
a. Weld the washers to the 16LJ unit base.
b. Tighten the nuts.
1.8 - Leak test and method of charging/removing
nitrogen gas
If the chiller is leaking, please refer to the following items and
Fig. 5.
1.8.1 - Leak test
This describes the chiller leak test procedure, using pressurized
nitrogen gas (N2gas).
Equipment to use
• Nitrogen gas cylinder
• Pressure regulator
• Pressure-proof hose
• Flashlight
• Soapy water
• Adjustable wrench
• Hose band
• Vacuum gauge (0-1 kPa)
• Pressure gauge (0-100 kPa)
Requirement to meet
Pressurize the chiller up to 50 kPa with the nitrogen gas. Use a
soapy water solution and check that there are no bubbles at any
of the joints.
Nut
Weld Washer
Machine base
Fig. 4
NOTE: Weld repair can be done after
removing the N2gas. Refer to 1.8.3
Fig. 3

11
1.8.2 - Method of charging nitrogen gas
This is the procedure for charging nitrogen gas (N2gas) to
the chiller.
Equipment to use
• The required amount of N2gas:
16LJ Volume 16LJ Volume
litres litres
11 1640 31 5030
12 1580 32 4830
13 2510 41 6150
14 2380 42 5910
21 3150 51 8240
22 3010 52 9350
23 4210 53 10350
24 4020
• Pressure regulator
• Pressure-proof hose
• Adjustable wrench
• Valve key for N2gas cylinder
• Pressure gauge (0-100 kPa)
The pressure in the chiller is charged to 50 kPa at the
generator pressure gauge.
Precautions
• Since the N2gas cylinders are pressurized up to 15 MPa
be careful when handling them.
• Do not suddenly raise the primary or secondary
pressure of the pressure regulator.
• Fix the N2gas cylinder so that it cannot fall down.
• Be sure not to open V1, V2 during this work.
Procedure (see Fig. 5)
• Attach a pressure regulator to the N2gas cylinder.
• Connect the vacuum gauge to SV2. Open SV2.
• Connect a pressure-proof hose to the outlet of the
pressure regulator, then slightly open the valve at the
top of the cylinder in order to purge the air from the
hose. After purging, close the valve.
• Connect the other end of the hose to SV1 and x it
with a hose band.
• Check that V1, V2, V3, B, SV1 are fully closed.
• Open the V3 and B-valve and then open SV1.
NOTE: B-valve should be closed after the solution is
charged to the chiller.
• Using the pressure regulator, charge a small amount of
N2gas into the chiller.
• Watch the vacuum gauge while N2gas is charged.
When the pressure inside the chiller reaches the
required pressure, close SV1, V3, and B-valve. Then
close the valve of the cylinder.
• Remove the hose from SV1 and attach the service valve
cap to the service valve with sealant.
• Remove the pressure regulator and the vacuum gauge.
• Close SV2.
1.8.3 - Removing nitrogen gas (see Fig. 5)
Follow this procedure to remove N2gas from the chiller.
Equipment to use
Adjustable wrench
Requirement to meet
The pressure in the chiller is reduced down to atmospheric
pressure.
Precautions
• Be sure not to open V1, V2 during this work.
• Adequately ventilate the machine room.
Procedure
• Check that the V1, V2, V3, SV1, SV2 are fully closed.
• Open V3.
• Remove the cap and the are nut of SV1, and open the
valve.
• When the generator pressure gauge shows atmospheric
pressure, close SV1 and V3.
Fig. 5
Purge tank
Liquid trap
B-valve
Purge pump
Maintenance
pressure gauge

12
1.9 - Piping
1.9.1 - Connect each pipe according to exhibit LE and the
specication drawings.
• Make all necessary connections to the building chilled and
cooling water systems. Ensure that all piping is adequately
supported and that no strain is placed on the chiller
nozzles and connecting flanges.
• Provide adequate temperature and pressure sockets or taps
on all supply and return piping.
1.9.2 - Flushing
All water system pipes must be ushed before the water is
circulated in the chiller.
1.10 - Field wiring
CE marking
Power supply connections should be in accordance with CE
and comply with overvoltage category III (IEC 60664). All
other connections should be in accordance with overvoltage
category II. All wiring must be in accordance with CE
requirements.
• Refer to exhibit LF and the specication drawings for
wiring connections.
• Supply power to the hot water control valve and hot water
shut-off valve.
• Refer to chapter 2.3 - Electrical check.
• A properly qualied electrician should carry out the
electrical wiring.
1.11 - Purging (see Fig. 5)
• Ensure that the power supply is continuous.
• Remove nitrogen gas (refer to chapter 1.8.3.)
• Fill the purge oil pump to the centre of the red mark of
purge pump level gauge.
• Turn on the control panel main breaker and the purge
pump switch. Check the direction of rotation. If the
direction is wrong, turn off the power supply to the chiller.
• Then change any two of the wires of main power supply
source. The chiller was connected with all wires meeting
the same phase. Run the purge pump continuously.
• Connect the vacuum gauge (1 kPa) to SV2.
- Open SV2.
- Open V1, V3, and B-valve to purge the chiller.
- After one hour open V2.
• Operate the purge pump until the vacuum gauge shows 0.5
kPa. Refer to the following table.
16LJ Time
11-14 5 hours
21-32 12 hours
41-53 24 hours
1.11.1 - Carry out a bubble test (refer to Fig. 6)
Equipment to use
• Purge pump exhaust attachment
• Graduated cylinder
• Vinyl hose (ø 6 mm)
• Bucket
• Putty
• Stop watch
• Vacuum gauge (0 to 1 kPa)
Required purge rate
16LJ Standard value
ml per 10 min
11 < 15
12 < 15
13 < 15
14 < 15
21 < 25
22 < 25
23 < 25
24 < 30
31 < 30
32 < 30
41 < 40
42 < 40
51 < 45
52 < 45
53 < 50
Note: 1 ml is 1 cm3
Procedure
• Purge the air from the chiller until the internal pressure
in the chiller reaches required degree of vacuum, then
continue purging for at least one hour.
• Connect the vacuum gauge to SV2, and open SV2.
• Make sure that the attained purge pump vacuum is below
0.5 kPa.
• Remove the exhaust port cap of the purge pump, and
install the attachment to the exhaust port. Fit a vinyl hose
to the attachment as shown in Fig. 5 and Fig. 7.
• Open V1, close V2 and V3.
• Continue operating the purge pump for one minute under
the conditions above. Then measure the volume of bubbles
(the measured volume is called A ml). Do not submerge
the vinyl hose more than 10 mm during this measurement.
If bubbles collect, inspect and tighten the connections
downstream of V2 and V3. If bubbles still appear after
tightening, measure the volume collected for 10 minutes.
• Open V1 and V3. Close V2. The gas ballast valve and the
oil delivery valve should be closed.
• Continue operating the purge pump under the conditions
above. Measure the volume of bubbles for 10 minutes
(the measured volume is called B ml). The measurement
should be repeated at least three times. During these
measurements the attained purge pump vacuum should be
kept below 0.5 kPa.
• B ml - A ml is the result of the bubble test.
• After the bubble test, the gas ballast valve should be
opened. The oil delivery valve should be opened to check
if any water is contained in the purge pump oil. If water is
observed, drain the water and charge with new oil.

13
1
3
2
4
5
6
7
9
10
11
8
10 mm
12
Fig. 6
Legend
1 3/8" copper tube
2 Flare nut
3 Nipple (3/8")
4 Bushing (1-1/4")
5 Attachment
6 Vinyl hose
7 Suction port
8 Graduated cylinder
9 Discharge port
10 Purge pump
11 Tank
12 Water
2 - TEST OPERATION
2.1 - External visual inspection
The items below must be accessible after tting the insulation:
• Dampers, service valves and sight glass.
• Temperature sensors and pressure gauges should be
replaceable.
• Bar-thermometers need to be inserted into the wells
provided on water headers and solution pipes.
• Evaporator headers should be removable.
2.1.1 - Chiller insulation must be correctly tted.
The following position should not be insulated.
• The motor section of the refrigerant pump
• The rupture disk
2.1.2 - Installation checks
• There should not be any rust on the chiller.
• Flange and bolted connections should not be loose.
• There should not be any liquid leakage from the chiller.
• Ensure that the chiller components are not damaged.
• Ensure that no chiller components are missing.
• Ensure that wiring and piping are not damaged.
2.2 - Solution charge
Standard units are shipped fully charged with solution, inhibitor
and alcohol.
2.3 - Electrical check (see Fig. 7)
The electrical specications must comply with the control panel
nameplate data. Check the eld wiring and the palladium cell
heater wiring. Refer to exhibit LF and the specication drawings.
2.3.1 - Check the motor insulation resistance
Always ensure that the motors are disconnected from the
wiring before carrying out this check. The standard value is
10 MΩ minimum. The insulation resistance of the absorbent
pump, solution pump and purge pump should be measured at
the secondary terminals of each magnetic contactor.
2.3.2 - Measuring the insulation resistance
Measure the insulation resistance of absorbent pumps, refrigerant
pump and purge pump using the following equipment:
• 500 V d.c. megger
• Screwdriver
2.3.3 - Precautions
The insulation resistance should be 10 MΩ minimum. Be sure
to perform this measurement at the seasonal maintenance and
after pump replacement.
1.12 - Insulation
• After the chiller has been installed, it must be insulated.
• Before tting the insulation, the chiller should be placed
in its permanent position.
• To t insulating materials, use appropriate xtures and
ttings.
• Insulation on piping connections, access covers and ange
sections should be easily removable.
• The drawings show the areas to be insulated and the
recommended insulating materials and procedures. Please
refer to exhibit LG.
• The insulating material should be bre glass.
• The coeffcient of thermal conductivity is ≤ 0.04 W/(mK)

14
‚R0 ‚S0 ‚T0
PE
88
A
P
51
R
51
3 to
MA
3 to
MP
3 to
MR
R
88
MCBM
P
88
51
A
U11 V11 W11
U1 V1 W1
* * *
U21 V21 W21
U2 V2 W2
* * *
U31 V31 W31
U3 V3 W3
* * *
R S T
X Y Z
R1 S1 T1
L1 L2 L3
Purge pump Refrigerant pump Absorbent pump
Fig. 7
Filter
(Main circuit breaker)
2.4 - Initial control board setting
2.4.1 - Time setting
Refer to the operation and maintenance manual.
2.4.2 - Turn on the backup battery on the control board.
Refer to the operation and maintenance manual.
2.4.3 - Check the control board parameters.
Refer to the checklist, specication drawings and exhibit LI.
2.5 - Damper setting and valve position
2.5.1 - Damper setting
Refer to the specication drawings and exhibit LJ.
2.5.2 - Check valve opening status and switch positions
The position of each valve and switch is different for each
operation mode. Refer to the operation and maintenance
manual.
2.6 - Purging
2.6.1 - Ensure the gas ballast valve is closed before starting
the purge pump.
During operation of the purge pump, the gas ballast valve
should be opened. However if the valve is opened too far, purge
pump oil may spill from the oil charge port.
2.6.2 - Bubble test
Before conducting the bubble test, purge the chiller for at
least one hour. The gas ballast valve should be closed during
the bubble test. Please refer to the table in the chapter 1.11.1
"Bubble test".
2.3.4 - Procedure
• Switch off the power supply during the work. Make sure
to turn off the circuit breaker (MCBM).
• Connect the earth wire of the megger to the earth terminal
in the control panel.
• Measure the insulation resistance of each motor at the
following terminals on the control panel and at the wires
disconnected in chapter 2.3.1.
• For positions measured with the megger see Fig. 7:
- Absorbent pump (terminals) : U1/V1/W1
- Refrigerant pump (terminals) : U3/V3/W3
- Purge pump (terminals) : U4/V4/W4
• Record the measured values.
MP
3 ~
MR
3 ~
MA
3 ~

15
Generator temperature
Press the "SET" and " "keys simultaneously for about
2 seconds.
Press the " SET" key for about 2 seconds.
Press the " SET" key 3 times.
Press the "SET" key for about 2 seconds.
Press the " " or " " key.
Press the "SET" key.
Press the " " key once.
Press the "SET" key for about 2 seconds.
Set the " " key to 0.
Press the "SET" key.
Press the "BACK" key twice.
Generator temperature
Check that the hot water control valve closes.
Fig. 8 - Display example
Generator temperature
Press the "SET" and " "keys simultaneously
for about 2 seconds.
Press the "SET" key for about 2 seconds.
Press the " " key 3 times.
Press the "SET" key for about 2 seconds.
Press the " " or " " key.
Press the "SET" key for about 2 seconds.
Press the "BACK" key twice.
Generator temperature
Fig. 9 - Display example
2.7.3 - Motor alarm
After starting the chiller press the test levers of each thermal
relay.
Refrigerant pump
The data display shows J-10 "Refrigerant pump alarm".
Absorbent pump
The data display shows J-04 "Absorbent pump alarm".
2.7.4 - System alarm
Chilled water pump
a. Press the "RUN" key.
b. Stop the chilled-water pump.
c. Confirm that the data display on the control board shows
J-02 "Chilled-water pump interlock alarm" and the cooling
water pump stops immediately.
Cooling water pump
a. Press the "RUN" key.
b. Stop the cooling water pump.
c. Confirm that the data display on the control board shows
J-06 "Cooling water pump interlock alarm".
2.7.5 - Hot-water control valve operation
2.7.2 - Water alarm
Chilled-water temperature (setpoint: 2.5°C)
a. Provide 1-2 litres of ice water.
b. Press the "RUN" key on the control board.
c. Dip the chilled-water temperature sensor (DT1) removed
from the sensor holder into the water.
d. Confirm that the data display on the control board shows
J-01 "Chilled water temperature alarm".
Chilled-water ow rate
(setpoint: less than approximately 50% of rated flow)
a. Press the "RUN" key
b. Reduce the chilled-water flow rate by gradually closing
the evaporator outlet side valve.
c. Confirm that the data display on the control board shows
J-03 "Chilled water flow rate alarm".
Cooling water temperature
(setpoint 19°C for 30 minutes during operation)
a. Dip the cooling water inlet temperature sensor into the
water.
b. Press the "RUN" key
c. After about 30 minutes confirm that the data display on
the control board shows J-20 "Cooling water temperature
alarm".
2.7 - Function test
2.7.1 - Calibrating hot water control valves

16
2.8 - Operation
2.8.1 - Test operation
Before starting the chiller, check the opening of the valves and
the damper position. Refer to exhibit LJ.
Usually the units are factory-adjusted, but when assembling
them on site or operating them for the first time, the following
adjusting procedure should be taken.
2.8.2 - Operation and data record
Record data three times at 10 to 15-minute intervals during
stable operating conditions.
Tools required to record operation data
• Thermometer
• Pressure gauge
• Stop watch
• Solution sampling tool
• Gravimeter
• Concentration table as attached
2.8.3 - Absorbent sampling
Sampling should be carried out as follows:
• Sampling of diluted solution
• Sampling from SV4, located on the absorbent pump outlet
• Solution should be sampled twice. The sample quantity is
100 ml. The second sample should be used for analysis.
Mark Item Criteria Action
B1* Hammer sound No hammer sound Close the diluted solution damper little by little
(heat exchanger) (angle ± 2°)
* During the adjustment, service engineers must stay near the chiller, because it is running with the hot water control valve forced open.

17
1,40
1,45
1,50
1,55
1,60
1,65
1,70
1,75
1,80
1,85
0 10 20 30 40 50 60 70 80 90 100
65%
60%
55%
50%
45%
Relative density (kg/m3) x 10-3
Concentration (%)
Fig. 10 - Concentration versus temperature and relative density
Temperature (°C)
Crystallization

18
0,95
1,00
1,05
1,10
1,15
1,20
1,25
1,30
1,35
1,40
1,45
1,50
0 10 20 30 40 50 60 70 80 90 100
45%
40%
35%
30%
25%
20%
15%
10%
5%
0%
Relative density (kg/m3) x 10-3
Concentration (%)
Fig. 11 - Concentration versus temperature and relative density
Temperature (°C)

1919
3.1 - External visual inspection
• Lower shell ............................................................................ Not damaged ®Damaged ®
• Upper shell ............................................................................ Not damaged ®Damaged ®
• Heat exchangers ................................................................... Not damaged ®Damaged ®
• Evaporator headers ............................................................... Not damaged ®Damaged ®
• Absorber headers .................................................................. Not damaged ®Damaged ®
• Condenser headers ................................................................ Not damaged ®Damaged ®
• Control panel ........................................................................ Not damaged ®Damaged ®
• Absorption pump and isolation valves : ................................ Not damaged ®Damaged ®
• Refrigerant pump and isolation valves ................................. Not damaged ®Damaged ®
• Temperature sensors (11 sensors) ......................................... Not damaged ®Damaged ®
• Generator pressure switches ................................................. Not damaged ®Damaged ®
• Purge unit (diaphragm valves, liquid trap) ........................... Not damaged ®Damaged ®
• Chilled-water flow switch .................................................... Not damaged ®Damaged ®
• Cooling water flow switch (option) ...................................... Not damaged ®Damaged ®
• Refrigerant blow-down valve ............................................... Not damaged ®Damaged ®
• Purge tank pressure sensors .................................................. Not damaged ®Damaged ®
• Palladium cells and heater .................................................... Not damaged ®Damaged ®
3.2 - Verify field wiring and wiring of palladium cell heater
• Cooling water pump interlock (#121-#170) ......................... Not damaged ®Damaged ®
• Chilled-water pump interlock (#120-#170) .......................... Not damaged ®Damaged ®
• Run/stop remote signal (#323-#326) .................................... Not damaged ®Damaged ®
• Stop indication (#352-#353) ................................................. Not damaged ®Damaged ®
• Operation indication (#350-#351) ........................................ Not damaged ®Damaged ®
• Alarm indication (#354-#355) .............................................. Not damaged ®Damaged ®
• Chilled-water pump (#356-#357) ......................................... Not damaged ®Damaged ®
• Cooling water pump (#358-#359) ........................................ Not damaged ®Damaged ®
• Feedback indication (#362-#363) ......................................... Not damaged ®Damaged ®
• Earth connection (#G/PE) .................................................... Not damaged ®Damaged ®
• Wiring of palladium cell heater ............................................ Not damaged ®Damaged ®
For 460 V and 400 V: #232 and #0B on the control panel.
For 208 V: #232 and #202 on the control panel.
• Hot-water control valve (4 to 20 mA: #345-#346) ............... Not damaged ®Damaged ®
(24 V a.c.: #340-#344,#0)
• Hot-water shut-off valve (#347-#348) .................................. Not damaged ®Damaged ®
3.3 - Check of motor insulation resistance
Standard: 10 MΩ mimum
• Absorbent pump : ____________MΩ.................... Good ®Not good ‡ Repaired ®Replaced ®
• Refrigerant pump : ____________MΩ.................... Good ®Not good ‡ Repaired ®Replaced ®
• Purge pump : ____________MΩ.................... Good ®Not good ‡ Repaired ®Replaced ®
NOTE: Do not use this test for an electronic controller.
Project name : ____________________________
Chiller model : TSA-________________________
Serial number : ____________________________
Commissioned by : ___________ Date ____________
Accepted by : ___________ Date ____________
3 - CHECKLIST
Test operation in accordance with this check list.
3.1 - External visual inspection
3.2 - Verify eld wiring and wiring of palladium cell heater
3.3 - Check of motor insulation resistance
3.4 - Check of control board safety and switch settings
3.5 - Check of purge pump
3.6 - Verify auxiliary equipment
3.7 - Bubble test
3.8 - Verify valve opening status and switch positions
3.9 - Verify control board parameters
3.10 - Pre-operation checks
3.11 - Operation and data record
3.12 - Sample of absorbent taken (for analysis)

20
3.7 - Bubble test (when the unit is charged)
•___________ml (cm3)/10 min
•___________ml (cm3)/10 min
•___________ml (cm3)/10 min
Refer to the table in the chapter "Bubble test". Take measure-
ments several times to obtain the value given in the table.
3.8 - Verify valve opening status and switch position
Change-over valves
B-valve - in purge pipe (open): ....... Open ®Closed ®
Isolation valves
Valve open/close status should be as follows.
• Absorption pump (open):........ Open ®Closed ®
• Refrigerant pump (open):........ Open ®Closed ®
Diaphragm valves
Valve open/close status should be as follows.
• Manual purge Valve V1, V2, V3 (closed):
Open ®Closed ®
• Refrigerant blow-down valve (closed):
Open ®Closed ®
Service valves
Valve open/close status should be as follows.
• Charge/remove N2gas:.......................SV1 (closed)
Open ®Closed ®
• Purge unit:..........................................SV2 (closed)
Open ®Closed ®
• Refrigerant: ........................................SV3 (closed)
Open ®Closed ®
• Diluted solution:.................................SV4 (closed)
Open ®Closed ®
• Concentrated solution: .......................SV6 (closed)
Open ®Closed ®
• Generator pressure gauge:..................SV7 (open)
Open ®Closed ®
Switch - purge (off):....................................... On ®Off ®
3.6 - Verify auxiliary equipment
(For conrmation purpose only)
Water piping
• Chilled-water flow direction (inlet/outlet):
Good ®Not good ®
• Cooling water flow direction (inlet/outlet):
Good ®Not good ®
• Hot water flow direction (inlet/outlet):
Good ®Not good ®
• Chilled-water inlet/outlet valves: Open ®Closed ®
• Cooling water inlet/outlet valves: Open ®Closed ®
• Hot water inlet/outlet valves: Open ®Closed ®
Air vent valve, drain valve, pressure gauge, thermometer
Water circuit Air vent Drain valve Pressure Thermo-
valve gauge meter
Chilled water Yes No Yes No Yes No Yes No
Cooling water Yes No Yes No Yes No Yes No
Water pump duty
• Chilled water pump : ____________kW*
• Cooling water pump : ____________kW*
• Hot water pump : ____________kW*
Cooling tower : ____________kW*
* For information only
Cooling water temperature control:
Fan on-off ®2-way valve ®3-way valve®
Water charge into the chilled-water circuit:
Yes ®No ®
Water charge into the cooling water circuit:
Yes ®No ®
Water charge into the hot water circuit:
Yes ®No ®
Automatic cooling water blow-down device:
Yes ®No ®
Chemical cooling water feeding device:
Yes ®No ®
Check cooling water temperature control:
Good ®Not good ®
Water circulating conditions:
Item Chilled water Cooling water
Suction pressure (kPa/MPa) _____________ ___________
Delivery pressure (kPa/MPa) _____________ ___________
Current (A) _____________ ___________
Capacity of a main breaker: _______________A
3.4 - Check of control board safety and switch settings
• Generator pressure gauge (63GH) : _______________kPa/MPa
• Purge tank pressure sensor (69PR) : _______________kPa/MPa
• Absorbent pump thermal relay (51A) : _______________A
• Refrigerant pump thermal relay (51R) : _______________A
• Purge pump thermal relay (51P) : _______________A
3.5 - Check of purge pump
• No water in liquid trap : Yes ®No ®
• Oil quality : Clean ®Not cleaned ®‡Replace oil
(or contains water)
• Oil quantity : Good ®Not good ®‡Add new oil up to the centre of
sight glass or remove oil.
• Direction of rotation : Good ®(as arrow on V-belt cover) Not good ®‡Transpose two power supply wires