Sanyo CE42LH2WP - 16:9 Installation manual

UK5 Specification of expanding serial command
Item
Page Ver.1
Rev. B
Page
1
Specification of Expanding serial command
UK5
Ver 1.0󲷓Pub
Issued March 01 2010

UK5 Specification of expanding serial command
Item
Page Ver.1
Rev. B
Page
2
󲷲󲷠󲷭󲷸󲷮
TITLE
Specification of Expanding serial command
(Public Version)
MO EL
UK5
ISSUE SECT
.
S evelopment section 1
REVISIONS
Ver.
CHANGE OCUMENT
RAWN
ATE CHECK
ATE APPRO.
ATE
1.04
Pub
Fit to Japanese Ver.1.04 Fukushima
2010/3/1

UK5 Specification of expanding serial command
Item
Page Ver.1
Rev. B
Page
3
󲷌
󲷌󲷌
󲷌 Contents 󲷌
󲷌󲷌
󲷌
1. Overview ....................................................................................................................................7
2. Serial Interface Specification .....................................................................................................7
2.1. Transfer Specification..........................................................................................................7
2.2. onnection ..........................................................................................................................7
3. Notes for ommunication ..........................................................................................................8
4. Notes for explanation.................................................................................................................8
5. Functional Execution ommand................................................................................................9
5.1. Image control ommand.....................................................................................................9
5.2. P control ommand..........................................................................................................9
5.3. Input control ommand.......................................................................................................9
5.4. Screen control ommand ...................................................................................................9
5.5. Time control ommand .......................................................................................................9
5.6. Sound control ommand ....................................................................................................9
5.7. Setting control ommand ................................................................................................10
5.8. Other ommand ..............................................................................................................10
5.9. BASI ommand (Basic ommand)................................................................................ 11
6. Read ommand Table .............................................................................................................12
6.1. Image control Read ommand Table ...............................................................................12
6.2. P Read ommand Table ................................................................................................12
6.3. Video Read ommand Table ............................................................................................12
6.4. Input Read ommand Table ............................................................................................12
6.5. Screen Read ommand Table..........................................................................................12
6.6. Time Read ommand Table..............................................................................................12
6.7. Sound control Read ommand Table ...............................................................................13
6.8. Setting Read ommand Table ..........................................................................................13
6.9. Other Read ommand Table ............................................................................................13
6.10.BASI Read ommand Table (Basic ommand)............................................................13
7. Error code table .......................................................................................................................14
8. Functional execute command..................................................................................................15
8.1. Format ..............................................................................................................................15
8.2. Transfer Example .............................................................................................................15
8.3. Operation Requirements ..................................................................................................15
8.4 Image control ommand .................................................................................................16
8.4.1. F_BRIGHT ommand .................................................................................................16
8.4.2. F_ ONT ommand.....................................................................................................16
8.4.3. F_ OLOR ommand ..................................................................................................16
8.4.4. F_TINT ommand.......................................................................................................16
8.4.5. F_SHARP ommand ..................................................................................................16
8.4.6. F_WBAL ommand.....................................................................................................17
8.4.7. F_WBAL- ommand ....................................................................................................17
8.4.8. F_NZRED ommand ..................................................................................................18
8.4.9. F_FILM ommand.......................................................................................................18
8.4.10. F_IMAGE ommand .................................................................................................18
8.4.11. F_D DI ommand ....................................................................................................18
8.4.12. F_A A M ommand .............................................................................................18
8.4.13. F_ S ommand .....................................................................................................19
8.4.14. F_MPEGNR ommand.............................................................................................19
8.5. P control ommand..........................................................................................................19
8.5.1. F_H-POS ommand ...................................................................................................19
8.5.2. F_V-POS ommand....................................................................................................19
8.5.3. F_ LO K ommand ..................................................................................................20
8.5.4. F_PHASE ommand...................................................................................................20
8.6. Input control ommand.......................................................................................................20
8.6.1. F_INPUT ommand ....................................................................................................20
8.6.2. F_SOUR E ommand ...............................................................................................21
8.6.3. F_SYSTEM ommand ................................................................................................21
8.7. Screen control ommand ...................................................................................................21
8.7.1. F_S REEN ommand................................................................................................22
8.8. Time control ommand.......................................................................................................22
8.8.1. F_PANELH ommand.................................................................................................22

UK5 Specification of expanding serial command
Item
Page Ver.1
Rev. B
Page
4
8.9. Sound control Command............................................................................................ 22
8.9.1. F_VOLUME ommand ...............................................................................................22
8.9.2. F_MUTE ommand.....................................................................................................23
8.10. Setting control ommand .................................................................................................23
8.10.1. F_LANG ommand...................................................................................................23
8.10.2. F_P-MANE ommand...............................................................................................23
8.10.3. F_FDEFAULT ommand...........................................................................................23
8.10.4. F_TILE ommand .....................................................................................................24
8.10.5. F_TILE-H SETS ommand.......................................................................................24
8.10.6. F_TILE-V SETS ommand .......................................................................................24
8.10.7. F_TILE-H LO AT ommand.....................................................................................25
8.10.8. F_TILE-V LO AT ommand.....................................................................................25
8.10.9. F_TILE-BZL HADJ ommand...................................................................................25
8.10.10. F_TILE-BZLV ADJ ommand .................................................................................25
8.10.11. F_ON PROG ommand ..........................................................................................26
8.10.12. F_WINTER MODE ommand.................................................................................26
8.10.13. F_PANEL_PROTE T ommand............................................................................26
8.10.14. F_LEDLIGHT ommand .........................................................................................27
8.10.15. F_AVAUTOSHUT ommand...................................................................................27
8.10.16. F_ HILDLO K ommand ......................................................................................27
8.10.17. F_R INHIBITION ommand ..................................................................................28
8.11. Other ommand................................................................................................................28
8.11.1. F_KEYEMU ommand..............................................................................................28
8.11.2. F_POWER ommand ...............................................................................................28
8.11.3. F_FREEZE ommand...............................................................................................28
8.12. BASI ommand (Basic ommand)................................................................................29
8.12.1. POWER ON ommand ...............................................................................................29
8.12.2. POWER OFF ommand..............................................................................................29
8.12.3. POWER ON/OFF ommand .......................................................................................29
8.12.4. Input ommand............................................................................................................29
8.12.5. Wide "Natural" direct ommand ..................................................................................29
8.12.6. Wide "Zoom 16:9" direct ommand.............................................................................29
8.12.7. Wide "Title in 16:9" direct ommand ...........................................................................30
8.12.8. Wide "Zoom 14:9" direct ommand.............................................................................30
8.12.9. Wide "Title in 14:9" direct ommand ...........................................................................30
8.12.10. Wide "Full" direct ommand ......................................................................................30
8.12.11. Wide "Normal" direct ommand.................................................................................30
8.12.12. Picture mode ommand ............................................................................................30
8.12.13. AV1 direct ommand .................................................................................................31
8.12.14. RGB direct..................................................................................................................31
8.12.15. AV2 RGBHV direct ommand ...................................................................................31
8.12.16. AV2 YPbPr direct ommand......................................................................................31
8.12.17. AV3 direct ommand .................................................................................................31
8.12.18. DVI direct ommand..................................................................................................31
8.12.19. P direct ommand...................................................................................................32
8.12.20. P Auto adjust ommand..........................................................................................32
8.12.21. Factory setting ommand..........................................................................................32
8.12.22. POWER SAVE ON ommand ...................................................................................32
8.12.23. POWER SAVE OFF ommand .................................................................................32
8.12.24. hild lock ON ommand ...........................................................................................32
8.12.25. hild lock OFF ommand..........................................................................................33
8.12.26. R Inhibition ON ommand ......................................................................................33
8.12.27. R Inhibition OFF ommand.....................................................................................33
9 Status Read command .....................................................................................................33
9.1. Format ..............................................................................................................................33
9.2. Transfer Example .............................................................................................................33
9.3. Operation Requirements ..................................................................................................33
9.4. Image control Read ommand ........................................................................................34
9.4.1. R_BRIGHT ommand.................................................................................................34
9.4.2. R_ ONT ommand ....................................................................................................34
9.4.3. R_ OLOR ommand .................................................................................................34
9.4.4. R_TINT ommand ......................................................................................................34
9.4.5. R_SHARP ommand ..................................................................................................34
9.4.6. R_WBAL ommand ....................................................................................................35
9.4.7. R_WBAL-R ommand ................................................................................................35
9.4.8. R_WBAL-G ommand ................................................................................................35

UK5 Specification of expanding serial command
Item
Page Ver.1
Rev. B
Page
5
9.4.9. R_WBAL-B ommand.................................................................................................35
9.4.10. R_NZRED ommand ................................................................................................35
9.4.11. R_FILM ommand ....................................................................................................36
9.4.12. R_IMAGE ommand.................................................................................................36
9.4.13. R_D DI ommand....................................................................................................36
9.4.14. R_A A M ommand.............................................................................................36
9.4.15. R_ S ommand.....................................................................................................37
9.4.16. R_MPEGNR ommand ............................................................................................37
9.5. P control Read ommand................................................................................................38
9.5.1. R_HPOS ommand .................................................................................................38
9.5.2. R_VPOS ommand..................................................................................................38
9.5.3. R_PHASE ommand ..................................................................................................38
9.5.4. R_ LO K ommand ..................................................................................................38
9.6. Video control Read ommand............................................................................................39
9.6.1. R_SERSYS ommand................................................................................................39
9.7. Input control Read ommand.............................................................................................39
9.7.1. R_INPUT ommand....................................................................................................39
9.7.2. R_SOUR E ommand ...............................................................................................39
9.7.3. R_SYSTEM ommand ...............................................................................................40
9.8. Screen control Read ommand .........................................................................................41
9.8.1. R_S REEN ommand ...............................................................................................41
9.9. Time control Read ommand .............................................................................................41
9.9.1. R_PANELH ommand ................................................................................................41
9.9.2. R_MONH ommand ...................................................................................................41
9.10. Sound control Read ommand ........................................................................................42
9.10.1. R_VOLUME ommand .............................................................................................42
9.10.2. R_MUTE ommand ..................................................................................................42
9.11. Setting control Read ommand........................................................................................42
9.11.1. R_LANG ommand...................................................................................................42
9.11.2. R_P-MANE ommand...............................................................................................42
9.11.3. R_TILE ommand .....................................................................................................43
9.11.4. R_TILE-HSETS ommand........................................................................................43
9.11.5. R_TILE-VSETS ommand ........................................................................................43
9.11.6. R_TILE-H LO AT ommand ....................................................................................43
9.11.7 R_TILE-V LO AT ommand......................................................................................43
9.11.8. R_TILE-BZL H ADJ ommand ..................................................................................44
9.11.9. R_TILE-BZL V ADJ ommand ..................................................................................44
9.11.10. R_ON PROG ommand..........................................................................................44
9.11.11. R_WINTER MODE ommand.................................................................................44
9.11.12. R_PANELP ROTE T ommand.............................................................................45
9.11.13. R_LED LIGHT ommand ........................................................................................45
9.11.14. R_AV AUTOSHUT ommand .................................................................................45
9.11.15. R_ HILD LO K ommand.....................................................................................45
9.11.16. R_R INHIBITION ommand ..................................................................................45
9.12. Other Read ommand......................................................................................................46
9.12.1. R_STATUS ommand...............................................................................................46
9.12.2. R_SIGNAL ommand ...............................................................................................46
9.12.3. R_FREEZE ommand ..............................................................................................46
9.12.4. R_FAN LO K ommand ..........................................................................................46
9.12.5. R_TEMP ommand ..................................................................................................47
9.13. BASI Read ommand .....................................................................................................48
9.13.1. Power status Read ommand .....................................................................................48
9.13.2. Input mode Read ommand........................................................................................48
9.13.3. Picture mode Read ommand.....................................................................................48
9.13.4. Wide mode Read ommand........................................................................................48
9.13.5. Signal status Read ommand (Same as 9.12.2) ........................................................49
9.13.6. hild lock setting Read ommand...............................................................................49
9.13.7. Power save setting Read ommand ...........................................................................49
9.13.8. Panel usage time Read ommand ..............................................................................49
9.13.9. R inhibition Read ommand .....................................................................................49
9.13.10. Model number Read ommand.................................................................................50

UK5 Specification of expanding serial command
Item
Page Ver.1
Rev. B
Page
6
4
10. Specification ommand with address....................................................................................50
10.1. Outline...............................................................................................................................50
10.2. Functional execute command with address .....................................................................50
10.2.1. Format..........................................................................................................................50
10.2.2. Sequential execution function ......................................................................................51
10.3. Status read command with address .............................................................................51
10.3.1. Format..........................................................................................................................51

UK5 Specification of expanding serial command
Ver. Page
7
1. Overview
1. 1 This specification define MONITOR SET control commands for UK5 chassis products
communicating with LD-Net.
1. 2 These control commands are originally developed for the communication with LD-Net, but also
can be used to control a MONITOR SET through RS-232 from a P . These commands are
called “Expanding serial commands”.
2. Serial Interface Specification
2.1 Transfer Specification
Item Specification
Synchronous system Asynchronous
Transmission Speed 9600 / 19200
Data Length 8 bit
Parity None
Stop Bit 1
Flow ontrol None
Note󲷐󲷍 Transmission speed: initial setting value is 19200.
Note󲷑󲷍 Transmission speed can be changed in hotel option menu.
2.2 Connection
Dedicated serial cable for MONITOR SET must be used for the connection bwtween P
and MONITOR SET.
C MONITOR SET
COM 1 Control ort
󲷇
󲷇󲷇
󲷇D-Sub 9 in󲷈
󲷈󲷈
󲷈 󲷇
󲷇󲷇
󲷇D-Sub 9 in󲷈
󲷈󲷈
󲷈

UK5 Specification of expanding serial command
󲠐󱓁
󲷒󲷍󲎜
󲎜󲎜
󲎜

󲚖
󲚖󲚖
󲚖

󰻡󰜷󲠐
󰻡󰜷󲠐󰻡󰜷󲠐
󰻡󰜷󲠐 Ver. Rev.A Page
8
3. Notes for Communication
3.1 The MONITOR SET command is defined one command/one line that starts with “ ” and ends
with carriage return (0x0D).
3.2 There are two types of commands, Functional Execution ommands and Status Read
ommands.
[Example of Functional execution command]
“CF_BRIGHT_032” [CR]
Note : “_” indicates space
[Example of Status Read ommands]
Functional Execution ommand: “CR_RIGHT” [CR]
3.3 When it takes more than one second to receive one command, the function is not executed.
When it takes more than one second until the MONITOR SET receives carriage return since it
has received the first data “ ”, it clears the information of buffer.
3.4 The sequential commands transmission, the intervals of 100m seconds and more is needed.
3.4.1 When a command is delivered before returning [A K], the command may be ignored.
3.5 It takes about 5 seconds for initial set-up until turns to stand by condition after A power line
connected. During the time, set will not accept commands. So don’t send any command.
within 1sec More than 100ms
PD net → Set “ ” “F” “ ...” R
Next ommand
Set → PD net ommand A K R
arriage Return
󲷇Normally , a few ms 󲸝 1s ,
Power on process or P mode 5sec 󲷈
4. Notes for Communication
4.1 The data transmitted from the controller to monitor is called the command
The data respond from the monitor to controller is called the status.
4.2 [ R] 󲷙 arridge return code
The carried return cod is indicating the end of the command. It also added on the end of the
status.
4.3 󲷙 Space code
The space code is spelled underscore such as 󲷇 _ 󲷈
4.4 󲷄󲷐 󲷙 Parameter including in the command.
If there are multiple parameters, it is noted as %2, %3.
4.5 󲷄󲷄󲷄 󲷙 Indicating response error code.
Respond without error. It appears “000”.
The number indicating error number refer to 󲷖󲷍Error code.

UK5 Specification of expanding serial command
Item
󲷔󲷍The table of executive command Ver. Rev.A Page
9
5. Functional Execution Command
5.󲷐
󲷐󲷐
󲷐. Image control Command
Execute command Item
CF_BRIGHT_%1[CR]
Set Brightness value.
CF_CONT_%1[CR]
Set ontrast value.
CF_COLOR_%1[CR]
Set olor value.
CF_TINT_%1[CR]
Set Tint value.
CF_SHAR _%1[CR]
Set Sharpness value.
CF_WBAL[CR]
Set White Balance Mode.
CF_WBAL-R_%1[CR]
Set White Balance Red value.
CF_WBAL-G_%1[CR]
Set White Balance Green value.
CF_WBAL-B_%1[CR]
Set White Balance Blue value.
CF_NZRED_%1[CR]
Set Noise reduction mode.
CF_FILM_%1[CR]
Set Film mode.
CF_IMAGE_%1[CR]
Set Image mode. 󳞥The same as PI TURE mode󳞦
CF_DCDI_%1[CR]
Set D Di mode
CF_ACCACM_%1[CR]
Set A /A M mode.
CF_CCS_%1[CR]
Set S mode.
CF_M EGNR_%1[CR]
Set MPEG NR mode.
5.󲷑
󲷑󲷑
󲷑. C control Command
Execute command Item
CF_H- OS_%1[CR]
Set Horizontal position value.
CF_V- OS_%1[CR]
Set vertical position value.
CF_CLOCK_%1[CR]
Set lock value.
CF_ HASE_%1[CR]
Set Phase value.
5.󲷒
󲷒󲷒
󲷒. Input control Command
Execute command Item
CF_IN UT_%1[CR]
Select Input mode.
CF_SOURCE_%1[CR]
Set Input source.
CF_SYSTEM_%1[CR]
Set system.
5.󲷓
󲷓󲷓
󲷓. Screen control Command
Execute command Item
CF_SCREEN_%1[CR]
Select screen mode. 󳞥The same as WIDE mode󳞦
5.󲷔
󲷔󲷔
󲷔. Time control Command
Execute command Item
CF_ ANELH_%1[CR]
Initialize panel accumulated time.
󳞥The same as F_LAMPH󳞦
5.󲷕
󲷕󲷕
󲷕. Sound control Command
Execute command Item
CF_VOLUME_%1[CR]
Set sound value.
CF_MUTE_%1[CR]
ontrol Sound mutes ON/OFF.

UK5 Specification of expanding serial command
Item
󲷔󲷍The table of executive command Ver. Rev.A Page
10
5.󲷖
󲷖󲷖
󲷖. Setting control Command
CF_LANG_%1[CR]
Select OSD language.
CF_ -MANE_%1[CR]
Set Power management function.
CF_FDEFAULT_%1[CR]
Set to “Factory Default”.
CF_TILE_%1[CR]
Set tile mode ON/OFF.
CF_TILE-HSETS_%1[CR]
Set tile mode, the number of horizontal array.
CF_TILE-VSETS_%1[CR]
Set tile mode, the number of Vertical array.
CF_TILE-HLOCAT_%1[CR]
Set tile mode, the Horizontal allocation number.
CF_TILE-VLOCAT_%1[CR]
Set tile mode, the Vertical allocation number.
CF_TILE-BZLHADJ_%1[CR]
Set tile mode, the width of bezel󲷇Horizontal󲷈
CF_TILE-BZLVADJ_%1[CR]
Set tile mode, the width of bezel (Vertical)
CF_ON ROG_%1[CR]
Set On Program.
CF_WINTERMODE_%1[CR]
Set Winter mode.
CF_ ANEL ROTECT_%1[CR]
Set Panel protects.
CF_LEDLIGHT_%1[CR]
Set LED light setting.
CF_AVAUTOSHUT_%1[CR]
Set AV auto shut OFF.
CF_CHILDLOCK_%1[CR]
Set hild lock.
CF_RCINHIBITION_%1[CR]
Set t R Inhibit.
5.󲷗
󲷗󲷗
󲷗. Other Command
Execute command Item
CF_KEYEMU_%1[CR]
The same command as R hand set / button on the set.
CF_ OWER_%1[CR]
Set Power ON/OFF.
CF_FREEZE _%1[CR]
Set Freeze function.

UK5 Specification of expanding serial command
Item
󲷔󲷍The table of executive command Ver. Rev.A Page
11
5.󲷘
󲷘󲷘
󲷘. BASIC Command 󲷇
󲷇󲷇
󲷇Basic Command󲷈
󲷈󲷈
󲷈
No.
ommand Item omment
c1 00 POWER ON
c2 01 POWER OFF
c3 22 Input Toggle (AV1, AV2, AV3, …)(for 232 )
c4 23 Wide “Auto” direct
c5 24 Wide “Natural” direct
c6 25 Wide “Zoom 16:9” direct
c7 26 Wide “Title in 16:9” direct
c8 27 Wide “Zoom 14:9” direct
c9 28 Wide “Title in 14:9” direct
c10
29 Wide “Full” direct
c11
0F Wide “Normal” direct
c12
10 Wide toggle Toggle (Auto, Natural, …) (for 232 )
c13
30 Picture Toggle (Dynamic, Standard, …) (for 232 )
c14
70 AV1 direct
c15
71 RGB direct
c16
72 AV2 RGBHV direct
c17
73 AV2 YPbPr direct
c18
74 AV3 direct
c19
75 DVI direct
c20
76 P direct
c21
77 RF direct (for 232 )
c22
64 P Auto adjust
c23
92 Factory setting
c24
F PSAVE ON
Power save ON
c25
F PSAVE
OFF Power save OFF
c26
F LOK ON
hild lock ON
c27
F LOK OFF
hild lock OFF
c28
F DEA
RM Y R inhibition OFF
c29
F DEA
RM N R inhibition ON
c30
03 Power ON/OFF (toggle)

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
12
6. Read Command Table
6. 1 Image control Read Command Table
Status read command Item
CR_BRIGHT[CR]
Status of Brightness.
CR_CONT[CR]
Status of ontrast.
CR_COLOR[CR]
Status of olor.
CR_TINT[CR]
Status of Tint.
CR_SHAR [CR]
Sharpness.
CR_WBAL[CR]
Status of White Balance Mode information.
CR_WBAL-R[CR]
Status of White Balance Red
CR_WBAL-G[CR]
Status of White Balance Green
CR_WBAL-B[CR]
Status of White Balance Blue
CR_NZRED[CR]
Status of Noise reduction setting.
CR_FILM[CR]
Status of Film mode setting.
CR_IMAGE[CR]
Status of Image selection.󳞥The same as PI TURE mode󳞦
CR_DCDI[CR]
Status of D Di setting.
CR_ACCACM[CR]
Status of A /A M setting.
CR_CCS[CR]
Status of S setting.
CR_M EGNR[CR]
Status of MPEG NR setting.
6. 2 C Read Command Table
Status read command Item
CR_H- OS[CR]
Status of Horizontal position.
CR_V- OS[CR]
Status of Vertical position.
CR_ HASE[CR]
Status of PHASE value.
CR_CLOCK[CR]
Status of LO K value.
6. 3 Video Read Command Table
Status read command Item
CR_SERSYS[CR]
Status of current signal system.
6. 4 Input Read Command Table
Status read command Item
CR_IN UT[CR]
Status of Input selection.
CR_SOURCE[CR]
Status of Input source mode.
CR_SYSTEM[CR]
Status of system of Input mode.
6. 5 Screen Read Command Table
Status read command Item
CR_SCREEN[CR]
Status of screen size 󳞥The same of WIDE mode󳞦
6. 6 Time Read Command Table
Status read command Item
CR_ ANELH[CR]
Status of accumulated lifetime of panel.
󳞥The same as R_LAMPH ommand󳞦
CR_MONH[CR]
Status of accumulated lifetime of monitor
󳞥The same as R_PROJH ommand󳞦

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
13
6. 7 Sound control Read Command Table
Status read command Item
CR_VOLUME[CR]
Status of volume value.
CR_MUTE[CR]
Status of MUTE.
6. 8 Setting Read Command Table
Status read command Item
CR_LANG[CR]
Status of Language selection.
CR_ -MANE[CR]
Status of Power management setting
CR_TILE[CR]
Status of Tile mode ON/OFF setting
CR_TILE-HSETS[CR]
Status of Tile mode, the number of Horizontal array.
CR_TILE-VSETS[CR]
Status of Tile mode, the number of Vertical array.
CR_TILE-HLOCAT[CR]
Status of Tile mode, the number of Horizontal allocation.
CR_TILE-VLOCAT[CR]
Status of Tile mode the number of Horizontal allocation.
CR_TILE-BZLHADJ[CR]
Status of Tile mode, the width of bezel󳞥Horizontal󳞦
CR_TILE-BZLVADJ[CR]
Status of Tile mode, the width of bezel (Vertical)
CR_ON ROG[CR]
Status of On Program information/
CR_WINTERMODE[CR]
Status of Winter mode Information.
CR_ ANEL ROTECT[CR]
Statuses of Panel protect Information.
CR_LEDLIGHT[CR]
Status of LED light Information.
CR_AVAUTOSHUT[CR]
Status of AV auto shut OFF Information.
CR_CHILDLOCK[CR]
Statuses of hild lock Information.
CR_RCINHIBITION[CR]
Status of R Inhibit Information.
6. 9 Other Read Command Table
Status read command Item
CR_STATUS[CR]
Status of the operation of the monitor.
CR_SIGNAL[CR]
Status of with or without signal.
CR_FREEZE[CR]
Status of Freeze setting.
CR_FANLOCK[CR]
Statuses of fun lock error.
CR_TEM [CR]
Status of current temperature value.
6.10 BASIC Read Command Table󲷇
󲷇󲷇
󲷇Basic Command󲷈
󲷈󲷈
󲷈
No.
ommand Item Note
r1
CR0
Power On, Standby, power error,
r2
CR1
Input Mode AV1, AV2, ..., DVI, P
r3
CR WIDE
Wide mode Auto, Normal, Full, …
r4
CR ICTURE
Picture mode Dynamic, Standard, …
r5
CR SIGNAL
Signal existence Signal / No signal
r6
CR CHILD
hild lock On / Off
r7
CR SAVE
Power save On / Off
r8
CRTM
Panel usage time
r9
CR RMC
R inhibition On / Off
r10
CR MDL
Model number 42LM4

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
14
7 Error code Table
Error code  󰎽
󲷞 󳜪 Receiving the data that cannot be decoded
󳜪 The wrong indication of parameter
󲷇Wrong figured number, or wrong word is included.󲷈
󲷏󲷏󲷏 Normal receiving󲷇no error󲷈
󲷐󲷏󲷑 If the command of out of range is directly entered
valuable parameter.
󲷐󲷏󲷒 No matching with Hardware
( ommand for optional function which is not equipped.)
󲷑󲷏󲷐 If the command of “Out of range” is entered by
inclement or decrements by numeric value.
󲷒󲷏󲷐 While capturing the picture, no execution. Wait and
transmit command again.
󲷓󲷏󲷑 While PIN code is in operation, no execution.
Wait and transmit command again.
󲷐󲷏󲷐 The errors not including above.

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
15
󲷗
󲷗󲷗
󲷗 Functional Execution Command
󲷗
󲷗󲷗
󲷗.1 Format
P issues a command in format as below.
“CF_ Command ” [CR]
“CF_ Command _ ” %1 [CR]
“ F_ “ means header, ommand means the line of character, %1 means parameter
“_” menas space (Stop of ommand / Parameter)
Monitor set returns status after decording data and redady to receive command.
“000 ” [CR] (0x06, 0x0D) Receiving functional execution command
“nnn ” [CR] Except indication “000”, ommand does not execute because of any reason.
Receiving the data whicih can not decord, then “?” [ R] is returned.
8.2 Example of transmission
Set the monitor brightness 32 by expanding ommand.
P → Monitor 󲷙“CF_BRIGHT_32”[CR]
P ← Monitor 󲷙“000”[CR] received OK
8.3 Condition of operation
The monitor is following condition, some command executions are restricted.
The status is available in following condition.
Status of monitor set Effective command execution.
Stand-by mode 00󲷙POWER ON
F POWER ON
Abnormal temperature (Stand-by󲷈 00󲷙POWER ON
F POWER ON
Abnormal power condition󲷇Standby󲷈 00󲷙POWER ON
F POWER ON
Power save condition
00󲷙POWER ON
01󲷙POWER OFF
F POWER ON
F POWER OFF
Note󲷈While above condition, the error massage appears even in receiving other command.

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
16
8󲷍
󲷍󲷍
󲷍4 Image control Command
8. 4. 1 CF_BRIGHT Command
ommand
“󲷢󲷥󲷾󲷡󲷱󲷨󲷦󲷧󲷳󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤󲸤󲸤󲸤󲸤 Direct command of Bright setting.
Detail Set Bright in user control.
Available only normal Power ON condition.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 2 CF_CONT Command
ommand
“󲷢󲷥󲷾󲷢󲷮󲷭󲷳󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤󲸤󲸤󲸤󲸤 Direct command of ontrast setting.
Detail Set ontrast in user control.
Available only normal Power ON condition.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 3 CF_COLOR Command
ommand
“󲷢󲷥󲷾 OLOR󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤󲸤󲸤󲸤󲸤 Direct command of olor setting.
Detail olor setting in user control.
Available only normal Power ON condition.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 4 CF_TINT Command
ommand
“󲷢󲷥󲷾󲷳󲷨󲷭󲷳󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤󲸤󲸤󲸤󲸤 Direct command of Tint setting.
Detail Setting of Tint in user control.
Available only normal Power ON condition.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 5 CF_SHAR Command
ommand
“󲷢󲷥󲷾󲷲󲷧󲷠󲷱󲷯󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤󲸤󲸤󲸤󲸤 Direct command of Sharpness setting
Detail Setting of Sharpness in user control.
Available only normal Power ON condition.
Receiving OK
“󲷏󲷏󲷏”[ R]
Status
Receiving NG
“Error code”[ R]

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
17
8. 4. 6 CF_WBAL Command
ommand
“󲷢󲷥󲷾󲷶󲷡󲷠󲷫󲷾󲷄󲷐”[ R]
󲷄󲷐
󲷶󲷠󲷱󲷬”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Set Warm in White balance mode
“󲷢󲷮󲷮󲷫”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Set Warm in White balance mode
“󲷲󲷳󲷠󲷭󲷣󲷠󲷱󲷣”󲸤󲸤󲸤󲸤󲸤Set STANDARD in White balance mode
“󲷯󲷤󲷱󲷲󲷮󲷭󲷠󲷫”󲸤󲸤󲸤󲸤󲸤Set Personal in White balance mode
“󲷴󲷯”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Select󲷇Order of Warm → ool → Standard → Personal
→ Warm OFF󲷈
“󲷣󲷭”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Select reverse󲷇Order of Warm → Personal → Standard
→ ool → Warm󲷈
Detail Set White balance mode󲷇Available only normal Power ON condition.󲷈
Receiving OK
“󲷏󲷏󲷏”[ R]
Status
Receiving NG
“Error code”[ R]
8. 4. 7 CF_WBAL󲷌
󲷌󲷌
󲷌Command
ommand
“󲷢󲷥󲷾󲷶󲷡󲷠󲷫󲷌󲷄󲷐󲷾󲷄󲷑”[ R]
󲷄󲷐
“󲷱” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Red
“󲷦” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Green
“󲷡” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Blue
󲷄󲷑
“󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤 Selected color value can be directly assigned.
“󲷴󲷯”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Add +1in selected white balance %1.
“󲷣󲷭”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤Add -1in selected white balance %1..
Detail Set up assigned value in %1 of White Balance in User menu.
Available only normal Power ON condition.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 8 CF_NZRED Command
ommand
“󲷢󲷥󲷾󲷭󲷹󲷱󲷤󲷣󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷮󲷥󲷥”󲸤󲸤󲸤󲸤󲸤 Release Noise Reduction
“󲷫󲷐”󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Set up Noise Reduction Auto
“󲷫󲷑”󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Set up Noise Reduction Low
“󲷫󲷒”󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Set up Noise Reduction Mid
“󲷫󲷓”󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Set up Noise Reduction High
“󲷴󲷯”󲸤󲸤󲸤󲸤󲸤󲸤󲸤 hnage forward 󲷇order of OFF → L1 → L2 → L3 →
L4 → OFF󲷈
“󲷣󲷭”󲸤󲸤󲸤󲸤󲸤󲸤󲸤 hange backword 󲷇order of OFF → L4 → L3 → L2 →
L1 → OFF󲷈
Detail Set up Noise Reduction󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
18
8. 4. 9 CF_FILM Command
ommand
“󲷢󲷥󲷾󲷥󲷨󲷫󲷬󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷮󲷥󲷥”󲸤󲸤󲸤󲸤 Release Film mode
“󲷮󲷭” 󲸤󲸤󲸤󲸤 Select Film mode
“󲷴󲷯”󲸤󲸤󲸤󲸤󲸤󲸤 Switch upward
“󲷣󲷭”󲸤󲸤󲸤󲸤󲸤󲸤 Switch downward
Detail Release Film mode.󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 10 CF_IMAGE Command
ommand
“󲷢󲷥󲷾󲷨󲷬󲷠󲷦󲷤󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷯󲷤󲷱󲷲󲷮󲷭󲷠󲷫” 󲸤 Personal
“󲷣󲷸󲷭󲷠󲷬󲷨󲷢” 󲸤 Dynamic
“󲷲󲷳󲷠󲷭󲷣󲷠󲷱󲷣” 󲸤 Standard
“󲷤󲷢󲷮” 󲸤 Eco
Detail
Select image mod. 󲷇Available only normal Power ON condition.󲷈
Selected mode is stored in EEPROM. Then setup image mode is effective after
the set is turned ALL OFF.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 11 CF_DCDI Command
ommand
“󲷢󲷥󲷾󲷣󲷢󲷣󲷨󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷮󲷥󲷥”󲸤󲸤󲸤󲸤 Select D Di OFF.
“󲷮󲷭” 󲸤󲸤󲸤󲸤 Select D Di ON.
“󲷴󲷯”󲸤󲸤󲸤󲸤󲸤󲸤 Switch upward
“󲷣󲷭”󲸤󲸤󲸤󲸤󲸤󲸤 Switch downward
Detail Release D Di setup.󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 12 CF _ACCACM Command
ommand
“󲷢󲷥󲷾󲷠󲷢󲷢󲷠󲷢󲷬󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷮󲷥󲷥” 󲸤󲸤󲸤󲸤Set up A /A M to OFF.
“󲷵󲷨󲷵󲷨󲷣” 󲸤󲸤󲸤󲸤Set up A /A M to Vivid.
“󲷢󲷨󲷭󲷤󲷬󲷠” 󲸤󲸤󲸤󲸤Set up A /A M to inema.
“󲷲󲷯󲷮󲷱󲷳” 󲸤󲸤󲸤󲸤Set up A /A M to Sports.
“󲷴󲷯” 󲸤󲸤󲸤󲸤󲸤󲸤 Switch upward
“󲷣󲷭” 󲸤󲸤󲸤󲸤󲸤󲸤 Switch downward
Detail Release A /A M setup󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
19
8. 4. 13 CF_CCS Command
ommand
“󲷢󲷥󲷾󲷢󲷢󲷲󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷮󲷥󲷥” 󲸤󲸤󲸤󲸤 Set up S to OFF.
“󲷠󲷴󲷳󲷮” 󲸤󲸤󲸤󲸤 Set up S to Auto.
“󲷲󲷳󲷠󲷭󲷣󲷠󲷱󲷣” 󲸤󲸤󲸤󲸤 Set up S to Standard.
“󲷴󲷯” 󲸤󲸤󲸤󲸤󲸤󲸤 Switch upward
“󲷣󲷭” 󲸤󲸤󲸤󲸤󲸤󲸤 Switch downward
Detail Release S setup󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8. 4. 14 CF_M EG NR Command
ommand
“󲷢󲷥󲷾󲷬󲷯󲷤󲷦󲷭󲷱󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷮󲷥󲷥”󲸤󲸤󲸤󲸤 Set up MPEG NR to OFF.
“󲷮󲷭” 󲸤󲸤󲸤󲸤 Set up MPEG NR to ON.
“󲷴󲷯”󲸤󲸤󲸤󲸤󲸤󲸤 Switch upward
“󲷣󲷭”󲸤󲸤󲸤󲸤󲸤󲸤 Switch downward
Detail Release MPEG NR set up󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “Error code”[ R]
8.5 C control Command
8. 5. 1 CF_H󲷌
󲷌󲷌
󲷌OS Command
ommand
“󲷢󲷥󲷾󲷧󲷌󲷯󲷮󲷲󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤 Direct assignment of value of Horizontal position.
“󲸍󲸍󲸍󲸍” is maximum value, and is indicate cent Total Dots 󲷌Display Area H.
Detail Set up Horizontal position of P input signal.
󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “󲷐󲷏󲷐”[ R] 󲸤󲸤󲸤󲸤 Input is Video control
8. 5. 2 CF_V󲷌
󲷌󲷌
󲷌OS Command
ommand
“󲷢󲷥󲷾󲷵󲷌󲷯󲷮󲷲󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤Direct assignment of value of Vertical position.
“󲸍󲸍󲸍󲸍” is maximum value, and is indicate current Total Line 󲷌 Display Area V.
Detail Set up Vertical position of P input signal.
󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “󲷐󲷏󲷐”[ R] 󲸤󲸤󲸤󲸤 Input is Video control

UK5 Specification of expanding serial command
󲠐󱓁
󲷗󲷍Execute functional command Ver. Rev.G Page
20
8. 5. 3 CF_CLOCK Command
ommand
“󲷢󲷥󲷾󲷢󲷫󲷮󲷢󲷪󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤 Direct assignment of value of Horizontal position.
“󲸍󲸍󲸍󲸍” is maximum value, and is indicate current Total Dots 󲷌Display Area H.
Detail Set up lock of P input signal.󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “󲷐󲷏󲷐”[ R] 󲸤󲸤󲸤󲸤Input is Video control
8. 5. 4 CF_ HASE Command
ommand
“󲷢󲷥󲷾󲷯󲷧󲷠󲷲󲷤󲷾󲷄󲷐”[ R]
󲷄󲷐 “󲷏󲷏󲷏󲸝󲷐󲷏󲷏”󲸤󲸤Direct assignment of value of Vertical position.
“󲸍󲸍󲸍󲸍” is maximum value.
Detail Set up of Phase of P input signal
󲷇Available only normal Power ON condition.󲷈
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “󲷐󲷏󲷐”[ R] 󲸤󲸤󲸤󲸤Input is Video control
8. 6 Input control Command
8. 6. 1 F_IN UT Command
ommand
“󲷢󲷥󲷾󲷨󲷭󲷯󲷴󲷳󲷾󲷄󲷐”[ R]
󲷄󲷐
“󲷠󲷵󲷐” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Select AV1 (Not changing Source)
“󲷱󲷦󲷡” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Select RGB
“󲷠󲷵󲷑󲷸󲷯󲸁󲷯󲸑”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Select AV2 ( hanging Source to YpbPr)
“󲷠󲷵󲷑󲷱󲷦󲷡󲷧󲷵”󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤 Select AV2 ( hanging Source to RGBHV)
“󲷠󲷵󲷒” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤Select AV3 (Not changing Source)
“󲷣󲷵󲷨” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤Select DVI (Not changing Source)
“󲷯󲷢” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤Select P (Not changing Source)
“󲷭󲷤󲷳󲷶󲷮󲷱󲷪” 󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤󲸤Select Network
“󲷴󲷯” 󲸤󲸤󲸤󲸤󲸤󲸤 hange forward
“󲷣󲷭” 󲸤󲸤󲸤󲸤󲸤󲸤 hange backward
Detail Select input.󲷇Available only normal Power ON condition.󲷈
This ommand is just switching Input, not changing Source.
Receiving OK “󲷏󲷏󲷏”[ R]
Status
Receiving NG “󲷄󲷄󲷄”[ R]