Sanyo VM-6609 User manual

VM-6609
FILE NO.
REFERENCE No.SM5310252
L8MAA/US,XE,UK,AU
NOTE: 1. Parts order must co tai model umber, part umber, a d descriptio .
2. Substitute parts may be supplied as the service parts.
3. N.S.P. : Not available as service parts.
Desig a d specificatio s are subject to cha ge without otice.
(Product Code : 114 901 11)
(U.S. , Canada)
SERVICE M NU L
B/W Video Monitor
CONTENTS
SPECIFICATIONS .................................................................... 3
1. OPERATING INSTRUCTIONS ............................................. 5
2. SERVICE ADJUSTMENTS ................................................... 7
3. PARTS LIST ......................................................................... 9
4. CIRCUIT DIAGRAMS ......................................................... 13
(Product Code : 114 901 14)
(Europe)
VM-6609P
(Product Code : 114 901 16)
(U.K.)
(Product Code : 114 901 18)
( ustralia)

– 2 –
SAFETY PRECAUTIONS
WARNING:
Service should not be attempted by anyone unfamiliar with the necessary precautions for this recording or playback
equipment. The following precautions are necessary during servicing:
1. any electrical and mechanical parts in this recorder have
special safety-related characteristics for providing protec-
tion against shock, fire and other hazards. These charac-
teristics often go unnoticed in a visual inspection, and the
protection afforded by them cannot necessarily be ob-
tained by using replacement components with higher rat-
ings (voltage, wattage, etc.).
2. Replacement parts having special safety-related charac-
teristics are identified in this manual, and in the schematic
diagrams, by the symbol ! . These components have
values that are of special significance to product safety.
Should any component (identified by the symbol ) need
to be replaced, use only the part designated in the parts
List. Do not deviate from the specified resistance, wattage,
and voltage ratings.
3. Before returning the set to the customer, always perform an
AC leakage current check on the exposed metallic parts of
the cabinet, such as terminals, screwheads, metal over-
lays, etc. to be sure that the set is safe to operate without
the danger of electrical shock, Plug the AC line cord directly
into a 120 V AC outlet. (Do not use a line isolation trans-
former during this check.) Use an AC voltmeter with a
sensitivity of 5000 ohms per volt (or more) as follows:
Connect a 1500 ohms, 10 watt resistor, paralleled by a 0.15
mfd, 150 VAC capacitor, between a known good earth
ground (water pipe, conduit, etc.) and the exposed metallic
parts, one at a time. easure the AC voltage across the
1500 ohms resistor and 0.15 mfd capacitor combination.
Reverse the AC plug at the AC outlet and repeat the AC
voltage measurements for each exposed metallic part. The
measured voltage must not exceed 300 mVrms. This
corresponds to 200 µA AC. Any value exceeding this limit
constitutes a potential shock hazard and must be corrected
immediately.
4. Fuse symbol marks.
For CANADA
UNDERWRITERS LABORATORIES Standard
CAUTION "Risk of fire-replace fuse as marked"
For U.S.A.
Fuse rating is marked at
adjacent fuse.
Video
Monitor

– 3 –
EIA standard
9˝ measured diagonally, 90° deflection angle
ore than 800 TV lines (center)
Horizontal: 15.75 kHz (EIA), Vertical: 60 Hz (EIA)
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Focus volume
Sub bright volume
Vertical size volume
anual switchable, Hi/ 75 ohm (Lo)
Temperature: -10 °C to 40 °C, Humidity:10% to 90 %
AC 100 to 240 V 50/60 Hz
20 Watts
222 x 238 x 250 mm
4.5 kg
SPECIFICATIONS
VM- 09
System :
Picture tube :
Resolution :
Scanning frewuency :
Input terminals :
VIDEO A
VIDEO B
Outout terminals :
VIDEO A
VIDEO B
Sub Adjusting control :
Termination switch :
Operating environment :
Power source :
Power consumption :
Dimension (W x H x D ) :
Weight :
CCIR standard
9˝ measured diagonally, 90° deflection angle
ore than 800 TV lines (center)
Horizontal: 15.625 kHz (CCIR), Vertical: 50 Hz (CCIR)
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Composite video: 1 line, BNC connector, 1.0 V p-p 75 ohm negative sync
Focus volume
Sub bright volume
Vertical size volume
anual switchable, Hi/ 75 ohm (Lo)
Temperature: -10 °C to 40 °C, Humidity:10% to 90 %
AC 100 to 240 V 50/60 Hz
20 Watts
222 x 238 x 250 mm
4.5 kg
VM- 09P
System :
Picture tube :
Resolution :
Scanning frewuency :
Input terminals :
VIDEO A
VIDEO B
Outout terminals :
VIDEO A
VIDEO B
Sub Adjusting control :
Termination switch :
Operating environment :
Power source :
Power consumption :
Dimension (W x H x D ) :
Weight :

– 4 –
Fig. 2
WD
H
DISASSEMBLY
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
METAL TOP COVER
Fig. 1

– 5 –
1. OPERATING INSTRUCTIONS
1-1. FRONT PANEL CONTROLS
Fig. 3
1. Monitor Selector Switch (VIDEO A/B)
Turn this onitor selector switch A position for a
signal fed through the rear panel VIDEO A
connectors.
Then, turn this onitor selector switch B posi-
tion for a signal fed through the rear panel
VIDEO B connectors.
2. Contrast Control ( CONTRAST)
Turn to adjust picture contrast according to your
requirement.
3. Brightness Control ( BRIGHT)
Turn to adjust picture brightness according to
your requirement.
4. Power Indicator
Lights when the power is on.
Lit: When the power is on.
Unlit: When the power is off.
5. Power Switch (POWER)
Press this switch to turn the power on or off.
1-2. REAR PANEL CONTROLS & CONNECTION
1. AC input socket (AC INPUT)
Connect the AC power cord (supplied) securely
to this socket and to a wall outlet.
2. Video input terminals (VIDEO IN)
These terminals are used to input a video signal
source to this monitor.
Connect to the video output of a VCR or an-
other monitor (for loop through connection) or to
a video camera.
3. Video output terminals (VIDEO OUT)
These terminals are used to output a video
signal from this monitor.
Loop-through output of the video in BNC
connector, then connect to the video input of
another monitor or a VCR.
4. Termination Switch (HI/75 Ω (Lo))
Select the input impedance (HI/75 ohm).
When using only one monitor, turn the termina-
tion switch to the 75 ohm position. When using
more than one monitor, set all of the termination
switch to the monitors to the HI position.
However, the last monitor termination switch
should be the 75 ohm position for proper line
termination.
5. Focus control (FOCUS)
Turn to adjust picture focus to optimum focus.
. Sub-brightness control (SUB-BRI)
Turn to adjust picture brightness.
7. Vertical Size control (V-SIZE)
Turn to adjust picture vertical size of the picture.
54321

– 6 –
Fig. 5
Single Connection
Monitor
Video recorder
Video camera
To Video B
INPUT terminal
(Video signal cable)
To Video A
INPUT terminal
(Video signal cable)
(Rear panel)
To Video input
terminal
To Video input
terminal
Monitor
Video recorder
Fig. 4
Monitor Video recorder
To Video input terminal
Coaxial cable
Video camera
Fig.
1
3
25
47

– 7 –
ADJUST ENT
ITE
TI ING
PATTERN SETTING VR
LOCATION ADJUST ENT PROCEDURE
HORIZONTAL
HOLD AD-
JUST ENT
VERTICAL
SIZE ADJUST-
ENT
HORIZONTAL
WIDTH AD-
JUST ENT
VERTICAL
LINEARITY
ADJUST ENT
FOCUS
ADJUST ENT
RASTER
CENTERING
ADJUST ENT
RASTER TILT
ADJUST ENT
BRIGHTNESS
ADJUST ENT
VERTICAL
HOLD AD-
JUST ENT
INTERLACE
ADJUST ENT
PATTERN GENERATOR
ODE CROSS-HATCHED
PATTERN
PATTERN GENERATOR
ODE ONOSCPE
PATTERN
PATTERN GENERATOR
ODE CROSS-HATCHED
PATTERN
PATTERN GENERATOR
ODE CROSS-HATCHED
PATTERN
PATTERN GENERATOR
ODE CROSS-HATCHED
PATTERN
PATTERN GENERATOR
ODE CROSS-HATCHED
PATTERN
PATTERN GENERATOR
ODE CROSS-HATCHED
PATTERN
PATTERN GENERATOR
ODE FULL-WHITE
PATTERN
PATTERN GENERATOR
ODE ONOSCPE
PATTERN
CA ERA SIGNAL
Turn off horizontal sync. (pin to ground)
Adjust VR404 to make pattern upright.
Set the power switch "ON" and adjust
VR302 and VR304 until height for eye
comfort is obtained.
Horizontal width is adjusted by means of
the width coil L402 on the main PWB,
width standard hexagonal alignment tool.
Adjust L402 to make picture width within
"2" position.
Adjust the vertical linearity control VR301
for equal spaceing of lines between the
center extreme of scan.
The focus control may be adjusted for
optimum focus by VR405.
The raster is centered by rotating the two
small at the rear of the yoke.
Loosen the screw on the rear of deflection
yoke, rotating the yoke to correct position
tighten the screw.
Brightness can be controlled by VR406
and VR201 is the main control which is
controlled at exeternal side of front side.
VR402 is a sub-bright control which is
located on the main PWB.
The vertical hold is automatic stop rolling.
But can't hold must adjust VR303.
Adjust VR303 have gap of vertical scan
line distinguish clearly.
VR404
VR302
VR304
L402
VR301
VR405
VR402
VR303
VR303
2. SERVICE ADJUSTMENTS
1357 7531
1
3
5
1
3
5
5
3
1

5
3
1

Fig. 7
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO AX.
CONTRAST VR
AND BRIGHT
VR TO CENTER.
CONTRAST VR
AND BRIGHT
VR TO CENTER.

– 8 –
T902
VR404
H-HOLD
VR402
SUB-BRITE
VR302
V-SIZE
VR405
FOCUS
T403
L402
Q405
E
C
B
VR304
SUB-SIZE
VR301
V-LINE
VR303
INTERLACE
VR406
BRIGHTNESS
SW901 LED1 VR201
CONTRAST
SW202
CHANNEL
AIN BOARD
VR BOARD
Fig. 8
Fig. 9
MAIN BOARD
(Foil side)
VR BOARD
(Foil side)

9
3. PARTS LIST
N.S.P.: Not available as service parts.
CABINET & CHASSIS PARTS
1 645 046 0517 FRONT PANEL MT-9S OC-00067
[VM-6609,VM-6609P(UK.)]
1 645 047 0646 FRONT PANEL MT-9S AA-51
[VM-6609P(XE),(AU.)]
645 046 0487 VR KNOB MT-9 OC-00067
[VM-6609,VM-6609P(UK)]
645 047 06 VR KNOB MT-9 AA-51 [VM-6609P(XE),(AU)]
3 645 046 0494 SW KNOB MT-9 OC-00067
[VM-6609,VM-6609P(UK)]
3 645 047 0639 SW KNOB MT-9 AA-51 [VM-6609P(XE),(AU)]
4 645 046 043 LOGO MT-9AL OC-00067
[VM-6609,VM-6609P(UK)]
4 645 047 0547 LOGO MT-9 AL AA-51 [VM-6609P(XE),(AU)]
5 645 046 0500 LED LENS MT-9/1 /15/ 0
6 645 046 1019 VR ASS’Y MT-9S
7 645 046 0951 BRACKET LEFT MM-9M
8 645 046 0944 BRACKET RIGHT MM-9M
9 645 046 07 PCB GUIDE RALL PCB MM-9M
10 645 046 0968 BASE MM-9M
11 645 046 0999 FOOT PAD GL-19-B
1 645 046 0470 FOOT PAD RIVET MM-9M GL-19-B
13 645 046 0753 CRT MI0908P4AU CPT
14 645 034 3599 PH W/W SCR. 4*18MM
15 645 046 1057 VIDEO BOARD MT-9S
16 645 046 0975 METAL TOP COVER MT-9 AA-51
17 645 034 358 PH W/W SCR. 4*8MM
18 645 034 3841 ID LABEL 83*51MM (N.S.P.)
19 645 046 1064 MAIN BOARD MM-9S
0 645 046 098 JACK PLATE MT-9S AA-51
1 645 035 6 16 BH SCREW 4*6MM
645 034 361 SCREW+WASHER 3*6MM
3 645 046 0593 CRT GND WIRE/1015 AWG
4 645 035 6 3 WASHER OUT TEETH 4.5*8.5*0.5MM
5 645 046 494 BNC WASHER
6 645 046 4898 BNC NUT
7 645 046 0401 BNC CONNECTOR BNC 13- 8 75OHM
8 645 046 10 6 AC SOCKET ASS’Y MM-9
9 645 046 0814 YOKE MM-9
Note:
Alphabetic caracters enclose by ( ) in the escriptions in icate estination for the VM-6609P.
VM-6609P(AU): Australia VM-6609P(XE): Europe VM-6609P(UK): Unite King om
VM-6609: NTSC area (U.S.A., Cana a)
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
VM-6609
1
4
3
8
7
13
9
14
3
15
16 17
18
0
7
1
5
6
4
19
1
11
10
6
5
9
8

10
ELECTRICAL PARTS
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
MAIN BOARD MM-9S
645 046 1064
(CAPACITORS)
C 07 645 034 738 EC CAP . UF 50V T
C 08 645 034 714 EC CAP 0UF 16V T
C 09 645 040 8991 PEI CAP .033UF 50V 5% T
C 10 645 046 0036 PEI CAP .00 7UF 50V 5% T
C301 645 034 936 PEI CAP .1UF 50V 5% T
C30 645 040 8953 CC CAP 103PF 50V Y5P T
C303 645 034 653 EC CAP 1000UF 16V 10DIA.
C304 645 046 0005 CC CAP PF 50V Y5P T
C305 645 034 936 PEI CAP .1UF 50V 5% T
C306 645 034 936 PEI CAP .1UF 50V 5% T
C307 645 034 936 PEI CAP .1UF 50V 5% T
C308 645 046 00 9 CC CAP 47PF 50V 5% T
C309 645 034 936 PEI CAP .1UF 50V 5% T
C310 645 034 653 EC CAP 1000UF 16V 10DIA.
C311 645 034 608 EC CAP 100UF 16V T
C31 645 045 996 EC CAP 47UF 5V T
C313 645 044 3695 EC CAP 10UF 50V T
C314 645 046 0098 MEMB CAP .1UF 100V 5% T
C40 645 046 0043 PEI CAP .039UF 100V 5% T
C403 645 034 3018 MEMB CAP .01UF 63V 5% T
C405 645 034 3018 MEMB CAP .01UF 63V 5% T
C406 645 034 9 9 PEI CAP .01UF 50V 5% T
C407 645 034 936 PEI CAP .1UF 50V 5% T
C408 645 034 783 EC CAP 470UF 16V T
C409 645 040 8953 CC CAP 103PF 50V Y5P T
C410 645 034 9 9 PEI CAP .01UF 50V 5% T
C411 645 034 677 EC CAP 1UF 50V T
C41 645 045 9993 CC CAP 10 PF 1KV Z5U T
C413 645 046 0074 PPN CAP .0056UF 50V 5% T
C414 645 046 0067 PPN CAP .018UF 630V 5% 15MM
C415 645 045 9955 EC CAP 0UF 5V T
C417 645 046 0050 MEF CAP 3.3UF 100V 5% 0MM
C418 645 045 9979 EC CAP 470UF 5 V
C4 1 645 043 3139 CC CAP 103PF 1.5KV Z5U 10MM
C4 645 034 745 EC CAP . UF 50V T
C4 3 645 045 9986 EC CAP 4.7UF 160V T
C901 645 034 3070 X CAP .1UF 50V 10% 15MM
C901 645 040 9066 X CAP .1UF 75V 0% 15MM
C903 645 034 3087 Y CAP 47 PF 400V 0%
C904 645 034 3087 Y CAP 47 PF 400V 0%
C905 645 034 3087 Y CAP 47 PF 400V 0%
C906 645 045 9948 EC CAP 100UF 400V DIA.
C907 645 034 813 CC CAP 103PF 1KV Z5U 10MM
C908 645 046 0098 MEMB CAP .1UF 100V 5% T
C909 645 034 30 5 MEMB CAP . UF 63V 5% T
C910 645 044 3695 EC CAP 10UF 50V T
C911 645 034 653 EC CAP 1000UF 16V 10DIA.
C91 645 034 653 EC CAP 1000UF 16V 10DIA.
C914 645 034 813 CC CAP 103PF 1KV Z5U 10MM
C9 0 645 034 653 EC CAP 1000UF 16V 10DIA.
C9 5 645 046 0098 MEMB CAP .1UF 100V 5% T
(DIODES)
D301 645 034 3377 RECTIFIER DIODE 1N4003 T 5 MM
D401 645 046 0 7 RECTIFIER DIODE BYT56J
D40 645 046 0 7 RECTIFIER DIODE BYT56J
D404 645 046 0 7 RECTIFIER DIODE BYT56J
D405 645 034 3346 RECTIFIER DIODE BYT5 M T5 MM
D406 645 046 0 65 RECTIFIER DIODE PS106R T
D407 645 046 0 65 RECTIFIER DIODE PS106R T
D408 645 034 3315 DIODE 1N4148 T 5 MM
OR 645 034 3308 DIODE 1N4148 T
D901 645 046 0 41 RECTIFIER DIODE 1N4007 T 5 MM
D90 645 046 0 41 RECTIFIER DIODE 1N4007 T 5 MM
D903 645 046 0 41 RECTIFIER DIODE 1N4007 T 5 MM
D904 645 046 0 41 RECTIFIER DIODE 1N4007 T 5 MM
D905 645 046 0 34 RECTIFIER DIODE PG106R T 5 MM
D906 645 046 0 58 RECTIFIER DIODE BA159 T 5 MM
D907 645 046 0 34 RECTIFIER DIODE PG106R T 5 MM
D909 645 046 0 89 RECTIFIER DIODE 30DF 0MM
ZD901 645 046 0 7 ZENER DIODE HZ6A T
(FUSE)
F901 645 046 08 1 FUSE A/ 50V SLOWBLOW 5* 0MM
(INTEGRATED CIRCUITS)
IC301 645 046 01 8 LINEAR IC TDA1175P
IC401 645 046 0104 LINEAR IC LM1391N
OR 645 046 0111 LINEAR IC MC1391P
IC901 645 034 6 31 LINEAR IC 4N35 W=10MM
Q903 645 034 316 REGULATOR IC TL431 T
OR 645 034 3179 REGULATOR IC KA431 T
(INDUCTORS)
L401 645 046 0883 CHOCK COIL 0 UH 0%
OR 645 046 0876 CHOCK COIL 0 UH 0%
OR 645 046 0890 CHOCK COIL 0 UH 0%
L40 645 046 0838 WIDTH COIL VM-14AF
OR 645 046 0845 WIDTH COIL VM-14AF
L40 645 046 085 WIDTH COIL VM-14AF
L403 645 046 0869 LINEARITY COIL 15 UH 0%
L404 645 046 0906 PEAKING COIL 33 UH 10% T
L903 645 046 0883 CHOCK COIL 0 UH 0%
OR 645 046 0876 CHOCK COIL 0 UH 0%
OR 645 046 0890 CHOCK COIL 0 UH 0%
(SEMICONDUCTORS)
Q 05 645 034 3 09 TR SA733P T
OR 645 046 0 10 TR KSA733CG T
Q301 645 046 0 03 TR SD667C T
OR 645 046 014 TR SC 35 T
Q401 645 034 3 54 TR SC945 T
OR 645 034 3 16 TR SC1815GR T
Q403 645 046 0159 TR SC1959Y T
Q405 645 046 0166 TR SC4161M
Q901 645 046 0180 TR SC3866 -MR
OR 645 046 0173 TR SC3447M
Q90 645 046 0135 TR SC1 13 T
(RESISTORS)
R 01 645 034 356 CF RES 75OHM 1/4W 5% T 5 MM
Note:
1. Materials of Capacitors and Resistors are abbreviated as follows ;
Resistors Capacitors
CF RES Carbon Film Resistor MEF CAP Metalli ed Polyester Film Capacitor
MF RES Metal Film Resistor (Non-inductive)
MOF RES Metalli ed Oxide Film Resistor MEMB CAP Mini Box Metalli ed Polyester Capacitor
(Non-inductive)
PEI CAP Polyester Film Capacitor (Inductive)
PPN CAP Polypropylene Film Capacitor (Non-inductive)
PPS CAP Polypropylene and Metalli ed Polypropylene
Film Capacitor (Non-inductive)
MPP CAP Metalli ed Polypropylene Capacitor
(Non-inductive)
X CAP(MKP) Metalli ed Polypropylene Film Capacitor
(Non-inductive)
CC CAP Ceramic Capacitor
EC CAP Electrolytic Capacitor
2. N.S.P. : Not available as service parts.

11
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
R 645 045 9610 CF RES 00OHM 1/4W 5% T 5 MM
R 3 645 045 9764 CF RES 680KOHM 1/4W 5% T 5 MM
R 4 645 034 0 8 CF RES 0OHM 1/4W 5% T 5 MM
R 5 645 034 71 CF RES 560OHM 1/4W 5% T 5 MM
R 6 645 034 71 CF RES 560OHM 1/4W 5% T 5 MM
R 8 645 045 9641 CF RES . MOHM 1/ W 5% T 5 MM
R 9 645 034 04 CF RES . KOHM 1/4W 5% T 5 MM
R 31 645 045 96 7 CF RES 00KOHM 1/4W 5% T 5 MM
R301 645 045 98 5 MOF RES 1OHM 1W 5% 15MM
R303 645 040 8809 CF RES 33KOHM 1/4W 5% T 5 MM
R304 645 045 9719 CF RES 5.1KOHM 1/4W 5% T 5 MM
R305 645 034 059 CF RES KOHM 1/4W 5% T 5 MM
R306 645 034 0 CF RES 4.3KOHM 1/4W 5% T 5 MM
R307 645 040 87 4 CF RES 1OHM 1/ W 5% T 5 MM
R308 645 034 40 CF RES 4.7KOHM 1/4W 5% T 5 MM
R309 645 045 9764 CF RES 680KOHM 1/4W 5% T 5 MM
R311 645 034 04 CF RES . KOHM 1/4W 5% T 5 MM
R31 645 045 9603 CF RES 18KOHM 1/4W 5% T 5 MM
R313 645 034 6 CF RES 47OHM 1/4W 5% T 5 MM
R314 645 045 9801 MF RES 70KOHM 1/4W 1% T 5 MM
R315 645 034 1991 CF RES 150KOHM 1/4W 5% T 5 MM
R316 645 034 189 CF RES 100KOHM 1/4W 5% T 5 MM
R317 645 045 9696 CF RES 3.3OHM 1/4W 5% T 5 MM
R318 645 034 88 CF RES 5.6KOHM 1/4W 5% T 5 MM
R319 645 034 04 CF RES . KOHM 1/4W 5% T 5 MM
R3 0 645 045 9788 CF RES 8 0KOHM 1/4W 5% T 5 MM
R401 645 045 9849 MOF RES OHM 3W 5% 0MM
R40 645 045 9740 CF RES 6 OHM 1/4W 5% T 5 MM
R403 645 034 004 CF RES KOHM 1/4W 5% T 5 MM
R404 645 034 103 CF RES .7KOHM 1/4W 5% T 5 MM
R405 645 034 363 CF RES 8 0OHM 1/4W 5% T 5 MM
R406 645 045 9757 CF RES 6 0OHM 1/ W 5% T 5 MM
R407 645 045 9870 MOF RES 70OHM 1W 5% 15MM
R408 645 034 04 CF RES . KOHM 1/4W 5% T 5 MM
R409 645 043 3160 CF RES 1.3KOHM 1/4W 5% T 5 MM
R410 645 045 97 6 CF RES 56KOHM 1/4W 5% T 5 MM
R411 645 034 88 CF RES 5.6KOHM 1/4W 5% T 5 MM
R41 645 034 1861 CF RES 1KOHM 1/4W 5% T 5 MM
R413 645 045 9689 CF RES 33KOHM 1/ W 5% T 5 MM
R414 645 045 9634 CF RES . KOHM 1/ W 5% T 5 MM
R415 645 034 19 CF RES 1 KOHM 1/4W 5% T 5 MM
R417 645 045 9764 CF RES 680KOHM 1/4W 5% T 5 MM
R418 645 045 967 CF RES 70KOHM 1/4W 5% T 5 MM
R419 645 045 9580 CF RES 1MOHM 1/4W 5% T 5 MM
R4 0 645 045 9733 CF RES 560KOHM 1/4W 5% T 5 MM
R4 1 645 045 9764 CF RES 680KOHM 1/4W 5% T 5 MM
R4 4 645 034 011 CF RES OHM 1/4W 5% T 5 MM
R4 6 645 045 9894 MOF RES 6. KOHM W 5% 0MM
R901 645 045 9771 CF RES 680KOHM 1/ W 5% T 5 MM
R90 645 045 9863 MOF RES 0KOHM W 5% 15MM
R903 645 045 9917 CEMENT RES KOHM 5W 5% 5MM
R904 645 034 57 CF RES 47KOHM 1/4W 5% T 5 MM
R905 645 034 1861 CF RES 1KOHM 1/4W 5% T 5 MM
R906 645 034 1861 CF RES 1KOHM 1/4W 5% T 5 MM
R907 645 045 9887 MOF RES 330OHM 1W 5% 1 .5MM
R908 645 034 04 CF RES . KOHM 1/4W 5% T 5 MM
R909 645 045 9566 CF RES 100OHM 1/4W 5% T 5 MM
R910 645 034 57 CF RES 47KOHM 1/4W 5% T 5 MM
R911 645 045 983 MOF RES 1 0OHM 1W 5% 15MM
R91 645 034 64 CF RES 51OHM 1/4W 5% T 5 MM
R914 645 034 1861 CF RES 1KOHM 1/4W 5% T 5 MM
R915 645 045 9818 MF RES 4.75KOHM 1/4W 1% T 5 MM
R916 645 045 9795 MF RES 1. 1KOHM 1/4W 1% T 5 MM
R917 645 045 9900 FUSE RES 0.56OHM 1W 5% 15MM
R918 645 034 318 CF RES 680OHM 1/4W 5% T 5 MM
R919 645 034 1878 CF RES 10KOHM 1/4W 5% T 5 MM
R9 1 645 034 1878 CF RES 10KOHM 1/4W 5% T 5 MM
R9 645 045 99 4 W-W RES 3.9OHM 3W 5% 5MM
(SWITCH)
SW 01 645 046 0418 SLIDE SWITCH SS004-P01 BJ-PA6
(TRANSFORMERS)
T401 645 046 0777 DRIVE TRANS. VM-14AF
OR 645 046 0784 DRIVE TRANS. VM-14AF
OR 645 046 0791 DRIVE TRANS. VM-14AF
T403 645 046 0807 FBT TRANS. MM-9M
T901 645 046 09 0 LINE FILTER TM-14T 0MH
T90 645 046 0760 POWER TRANS. MM-9 VDE
(VARIABLE RESISISTERS)
VR301 645 034 3483 POT VR 100KOHM 6DIA.
VR30 645 046 0340 POT VR 500KOHM 6DIA.
VR303 645 034 35 0 POT VR 50KOHM 6DIA.
VR304 645 046 0333 POT VR 50KOHM 6DIA.
VR40 645 046 0340 POT VR 500KOHM 6DIA.
VR404 645 034 3476 POT VR 10KOHM 6DIA.
VR405 645 046 03 6 POT VR MOHM15DIA.
(MISCELLNEOUS)
645 034 4404 FUSE CLIP BOARD TYPE 5* 0MM
645 046 0548 LEAD WIRE/1007 4AWG 7MM
645 046 0609 L/W HOUSING 1007/1185 4/ 6
645 046 0616 L/W HOUSING 1015 4AWG L= 0
TP1 645 046 0371 CONNECTOR BASE 1038H
B40 645 046 0395 CONNECTOR BASE M11384
B404 645 034 3773 CONNECTOR BASE M 41855
B90 645 034 3735 CONNECTOR BASE M 41833-X
B903 645 034 3735 CONNECTOR BASE M 41833-X
BNC0 645 034 3674 CONNECTOR BASE M 4185
VIDEO BOARD MT-9S
645 046 1057
(CAPACITORS)
C 01 645 034 684 EC CAP UF 16V T
C 0 645 046 00 9 CC CAP 47PF 50V 5% T
C 03 645 046 0081 EC CAP 10UF 50V 0% T
C 04 645 034 783 EC CAP 470UF 16V T
C 05 645 046 001 CC CAP 7 PF 50V Y5P T
C 06 645 034 608 EC CAP 100UF 16V T
C 11 645 045 9993 CC CAP 10 PF 1KV Z5U T
C 1 645 043 3139 CC CAP 103PF 1.5KV Z5U 10MM
C 13 645 045 9931 EC CAP 100UF 100 V
C 15 645 034 714 EC CAP 0UF 16V T
C 16 645 045 9955 EC CAP 0UF 5V T
(DIODES)
D 01 645 034 3315 DIODE 1N4148 T 5 MM
OR 645 034 3308 DIODE 1N4148 T
(INDUCTOR)
L 01 645 046 0913 PEAKING COIL 4.7 UH 10% T
(SEMICONDUCTORS)
Q 01 645 034 3 16 TR SC1815GR T
OR 645 034 3 54 TR SC945 T
Q 0 645 034 3 09 TR SA733P T
OR 645 046 0 10 TR KSA733CG T
Q 03 645 034 3 16 TR SC1815GR T
OR 645 034 3 54 TR SC945 T
Q 04 645 046 0197 TR SD1609C
(RESISTORS)
R 0 645 040 8755 CF RES 16KOHM 1/4W 5% T 5 MM
R 03 645 045 9719 CF RES 5.1KOHM 1/4W 5% T 5 MM
R 04 645 045 9566 CF RES 100OHM 1/4W 5% T 5 MM
R 05 645 034 318 CF RES 680OHM 1/4W 5% T 5 MM
R 06 645 034 0 8 CF RES 0OHM 1/4W 5% T 5 MM
R 07 645 034 134 CF RES 330OHM 1/4W 5% T 5 MM
R 08 645 045 9665 CF RES 40OHM 1/4W 5% T 5 MM
R 09 645 045 9566 CF RES 100OHM 1/4W 5% T 5 MM
R 11 645 034 011 CF RES OHM 1/4W 5% T 5 MM
R 1 645 034 1984 CF RES 15KOHM 1/4W 5% T 5 MM
R 13 645 034 103 CF RES .7KOHM 1/4W 5% T 5 MM
R 14 645 045 9597 CF RES 150OHM 1/4W 5% T 5 MM
R 15 645 034 6 CF RES 47OHM 1/4W 5% T 5 MM
R 16 645 034 004 CF RES KOHM 1/4W 5% T 5 MM
R 17 645 034 158 CF RES 3.6KOHM 1/4W 5% T 5 MM
R 18 645 045 9856 MOF RES . KOHM 3W 5% 0MM
R 19 645 034 0 8 CF RES 0OHM 1/4W 5% T 5 MM
R 0 645 045 9658 CF RES 4OHM 1/ W 5% T 5 MM
R 1 645 045 9573 CF RES 1KOHM 1/ W 5% T 5 MM
R 7 645 045 970 CF RES 47KOHM 1/ W 5% T 5 MM
R 33 645 034 134 CF RES 330OHM 1/4W 5% T 5 MM
(SPARK GAPS)
SP 01 645 035 9408 SPARK GAP DSP 00V 10% T
SP 0 645 038 55 0 SPARK GAP 50V 0% 5MM T
(MISCELLANEOUS)
645 046 05 4 CRT SOCKET CRT 7PIN 0DIA.
B 01 645 034 3674 CONNECTOR BASE M 4185
B 0 645 038 5445 CONNECTOR BASE M 41856

1
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
B 03 645 034 3773 CONNECTOR BASE M 41855
B 04 645 046 0388 CONNECTOR BASE M 41854
CRT GND 645 034 3667 CONNECTOR BASE P 3514
VR ASS’Y MT-9S
645 046 1019
(SWITCH)
SW 0 645 046 04 5 ROTARY SWITCH 96S0947B
SW901 645 034 3810 POWER SWITCH SS-160-7
(LED)
LED1 645 046 0 96 LED 5DIA.
(VARIABLE RESISTOR)
VR406 645 046 0319 VR 00KOHM 9DIA. 10MM ND F 15
VR 01 645 046 030 VR 500OHM 9DIA. 10MM ND F 15
(MISCELLANEOUS)
B703 645 046 0388 CONNECTOR BASE M 41854
B 06 645 046 0654 SHIELD WIRE 547 6AWG
645 046 0647 L/W HOUSING 1007/ 4 L= 0
B901 645 046 06 3 L/W HOUSING/1015 18AWG
ACCESSORIES & PACKING MATERIALS
1 645 038 5933 POWER CORD NS8-5175N [VM-6609]
1 645 034 3971 POWER CORD 10-1VDE [VM-6609P(XE)]
1 645 040 9 64 POWER CORD NS8-5181N [VM-6609P(UK)]
1 645 040 9 57 POWER CORD NS8-5180N [VM-6609P(AU)]
645 046 0463 USER MANUAL CCTV [VM-6609]
645 047 0615 USER MANUAL CCTV [VM-6609P(XE),(AU),(UK)]
3 645 046 0449 CARTON MT-9S-EIA [VM-6609]
3 645 047 0561 CARTON MT-9S-CCIR [VM-6609P(XE),(AU),(UK)]
645 046 0739 POLYFORM MM-9M

-13-
12345678
A
B
C
D
E
F
G
H
I
J
K
BLOCK DIAGRAM
OVAEALL WIRING
4.CIRCUIT DIAGRAM
1
2
3
4
5
CONT_VR
POWER LED
B404
2
3
4
B206
BRIGHT_VR
4
3
5
1
2
3
2
1
B403
B204
VR402
R421
R914
GND
R211
C203
R233
VR PWB
RED
WHITE
YELLOW
BLACK
RED
BLUE
RED
RED 2
4
6
B202
R221
C213
R227
YELLOW
WHITE
ORANGE
1
2
3
5
B203
C212
Q203
C214(12V)
Q201
WHITE
RED
GREEN
BLUE
D406
VR405
R228
D408
L404
C207
MAIN PWBMAIN PWB VIDEO PWB

-14-
1 2 3 4 5 6 7 8
A
B
C
D
E
F
G
H
I
J
K
CRT
MAIN_PWB
VIDEO_PWB VIDEO_PWB
VR_PWB
VR_PWB
MAIN_PWB
VR_PWB
MAIN CIRCUIT DIAGRAM

-15-
12345678
A
B
C
D
E
F
G
H
I
J
K
F901
2A/250V
R901
470K
1/2W
C901
0.1µ
250VAC
T901 50mH
LINE FILTER
R902
220K 2W
R17
0.68
1W
C902
0.1µ
250VAC
1N4007 x 4
D903
D904
D901
D902
C910
10µ
C903
4700P
400VAC
R901
680K
1/2W
C906
0.22µ
R907
330
1W
R910
47K
C906
100µ
400V
R903
22K
5W
D906
BA159
L903
20µH
C908
0.1µ
100V
C905
4700P 400VAC
IC901 D905
PG106R
R909
100
D907
FG106R
R908
2.2K
R906
1K
Q902
2 C1213
R919
10K
Q903
TL431
R918
680
Q901
2 C3866
L
N
G
MAIN_PWB
MAIN_PWB
ZR901
R922
3.9 3W
C904
4700P
400VAC
VR_PWB
C907
0.01µ
1KV
T902
R905
1K
R912
51
ZD901
6C2
R904
47K
C925
0.1µ
100V
R915
4.75K
R916
1.2K
R920
NONE
R921
10K
C920
1000µ
16V
R914
1K
VR_PWB
C912
1000µ
16V
C911
1000µ
16V
D909
30DF2
C914
0.01µ
1KV
R911
120
1W
POWER CIRCUIT DIAGRAM

Feb./ '01 / 2300 MI Pri ted i Japa
SANYO Electric Co.,Ltd.
Osaka, Japa