Sanyo LMU-TK18AG2 User manual

INDEX
Page
PRECAUTIONS ----------------------------------------------------------------------------------- 2
1, MAIN SPECIFICATION --------------------------------------------------------------------- 3
2, TROUBLE SHOOTING ---------------------------------------------------------------------- 4,5
3, MAINTENANCE
3-1 LMU-TK18AG2 ------------------------------------------------------------------------ 6
3-2 LMU-TK18AG2TC -------------------------------------------------------------------- 7
4, BLOCK DIAGRAM ---------------------------------------------------------------------------- 8
5, CONNECTION DIAGRAM ------------------------------------------------------------------ 9
6, TABLE OF SIGNAL NAME ----------------------------------------------------------------- 10,11
7, EXPLODED VIEW AND PARTS LIST
7-1Exploded View ------------------------------------------------------------------------ 12
7-2Parts List
7-2-1 LMU-TK18AG2 ---------------------------------------------------------------- 13
7-2-2 LMU-TK18AG2TC ------------------------------------------------------------ 14
8, APPENDEX ------------------------------------------------------------------------------------- 15
Refer to the separate volume User’s Manual and CD-ROM
that included for instruction.
- 1 -

PRECAUTIONS
Placement precautions
lAvoid placing the unit in humid or dusty places, or where it will be exposed to excessive heat
(direct sunlight, heaters, etc.)
lDo not step on or set anything on the AC cord.
DAMAGE TO THE AC CORD IS A SAFETY RISK AND CAN CAUSE A FIRE.
lDo not connect the unit to the same AC as outlet with appliances that generate large amounts of
interference (such as heaters with thermostats, appliances with motors, etc.). It is best to use a
completely separate electrical outlet.
lKeep the unit away from water. If water accidentally enters the unit, unplug the AC power cord
immediately. DO NOT PLUG IN THE UNIT AGAIN.
Handling precautions
lAvoid bending, kinking or damaging the AC power cord.
lNever insert or remove the power cord with wet hands. Also, be sure to hold cord by the plug when
removing it from the outlet.
lDo not remove any parts that are held in place with screws. (The unit does not contain any user
serviceable items.)
lMaintain standard room temperature (5oC to 35oC, or 41oF to 95
oF) during use. Do not subject the
unit to shock or vibration. Do not move the unit while it is in use.
lA rapid increase in room temperature in cool weather can cause condensation to from inside the unit.
If this occurs, wait at least 15 minutes after turning the unit on before attempting to operate it.
- 2 -

1. MAIN SPECIFICATION
Model Name LMU-TK18AG2TC LMU-TK18AG2
Display
Panel Type TFT
Screen Size 18.1"
Pixel Pitch 0.2805 x 0.2805 mm
Effective Viewing Area 359.04 x 287.232 mm
Pixel Format 1,280 x 1,024 (SXGA)
Brightness 200cd/m2typ.
Response Time 75ms
Contrast 300 : 1 typ.
Viewing Angle (minimum) Left & Right :85 deg Up : 85 deg Down : 85 deg
Back Light CCFL x 2
Lamp Life Time 50,000 hours typ.
Video Control System Analog RGB
Video 0.7Vp-p 75 ohm
Input Signal Sync.Type/Level Separate TTL (+/-)
Horizontal 31.4 kHz –80 kHzSynchronization
Frequencies Vertical 56 -75 Hz
Colors 16.77million
Touch Panel
Type Capacitive -
Electrical Resolution 10bit (1,024 x 1,024) -
Communication Bi-directional asynchronous
RS-232C serial communication -
Baud rate 9,600 BPS (1,200 -19,200 BPS) -
Data 7 bit (7bit or 8bit) -
Stop bit 2 bit (1bit or 2bit) -
Parity non (odd, even, or non) -
Touch Life 150 million touches in any location. -
Touch Down Speed 15 ms -
Physical Video Signal 15pin mini D-Sub
Serial 9pin D-Sub -
Input Power Supply DC Jack
operating : 5 deg to 35 degOperating
Temperature Storage : -20 deg to 60 deg
Environment Humidity 30% to 85% RH (No Condensation)
Model Name SEA60N3-13.8A
Input 100-240VAC 50-60Hz
Power Supply
(AC Adapter) Output DC 13.8V 3.5A
53W max. 49W max.
Power Supply Consumption 2W in Energy Saving mode 1.5W in Energy Saving mode
Dimensions 446(W) X 368(D) X 65(H) mm 446(W) X 368(D) X 58.5(H) mm
Weight 6.7kg 5.3kg
Accessories AC Adapter, Power Cord, RGB
cable, Serial cable, OSD control box,
Touch Ware CD-ROM, User's Guide
AC Adapter, Power Cord, RGB
cable, OSD control box, User's
Guide
- 3 -

2. TROUBLESHOOTING
Check the following for troubles of LCD monitor.
No. Check Points Treatments Class
1
1Is the Power "ON" to a LCD Monitor ? Check AC outlet, AC cord, DC Jack and
Power switch for a LCD monitor A
2Is the Power "ON" to a Computer ? Check the Power for a Computer A
3Is a signal cable connected securely ? Check the connection of a signal cable A
4Is a computer standing by ? Be out of standing by condition, by operating
to a computer A
5Disconnected a signal cable ? or Bent a
terminal pin ? Ensure the connection of a signal cable B
6Is an AC Adapter defective? Replace an AC Adapter with the new one C
7Is the wire harness between main PCB and
LCD module secured firmly ? Check the connection of wire harness C
8Is the wire harness between LCD module and
DC/DC Comnv. secured firmly ? Check the connection of wire harness C
9Is the wire harness between DC IN PCB and
DC/DC Conv. PCB secured firmly ? Check the connection of wire harness C
10 Is the wire harness between main PCB and DC
IN PCB secured firmly ? Check the connection of wire harness C
11 Is the LCD module defective ? Replace a LCD module with the new one C
12 Is the Inverter block on LCD module defective ? Replace a LCD module with the new one C
13 Is the DC/DC Conv. PCB defective ? Replace a DC/DC Conv. PCB with the new
one C
14 Is the display circuit on main PCB defective ? Replace the main PCB with the new one C
15 Is the Power Supply circuit on main PCB
defective ? Replace the main PCB with the new one C
2
1Is a screen saver programming running ? Press any key or touch the mouse, to end the
screen saver program A
2Is the computer's signal timing not agreeable to
the LCD's specification ? Adjust the computer's signal timing, if possible B
3Is the Image Processing circuit on main PCB
defective ? Replace the main PCB with the new one C
3
1Is the wire harness between main PCB and
LCD module secured firmly ? Ensure the connection of wire harness C
2Is the LCD module defective ? Replace a LCD module with the new one C
3Is the Image Processing block circuit on main
PCB defective ? Replace the main PCB with the new one C
A It is possible to treated by end-user
B It might be possible to treat by end-user in some case.
C It must be treated by Professional Technical Staff
Symptom
No Picture with Back light OFF
No Picture with Back light ON
White/Grey on whole screen(Nothing on screen)
- 4 -

No. Check Points Treatments Class
6
1Is the wire harness between inverter and a LCD
module secured firmly ? Ensure the connection of a wire harness C
2Is the wire harness between one of inverters
and main PCB secured firmly ? Ensure the connection of a wire harness C
3Is the display circuit on main PCB defective ? Replace the main PCB with the new one C
7
1Is the adjustment for screen performed
correctly ? Adjust the screen correctly A
2Is the output level on image from a computer
not agreeable to LCD's specification ? Check the specification of a computer B
3Is the size of screen set correctly ? Set the size of screen again(refer to User's
Manual for computer) A
8
1Is the adjustment for screen performed
correctly ? Adjust the screen correctly A
2Is a signal cable connected securely ? Check the connection of a signal cable A
3Is a sigil cable extended ? Don't extend a signal cable A
4Is the output level on image from a computer
not agreeable to LCD's specification ? Check the specification of a computer B
5Is the Image Processing circuit on main PCB
defective ? Replace the main PCB with the new one C
9
1Is a signal cable connected securely ? Check the connection of a signal cable A
2Is the connection between main PCB and a
LCD module securely ? Ensure the connector of wire harness C
3Is the Image Processing circuit on main PCB
defective ? Replace the main PCB with the new one C
A It is possible to treated by end-user
B It might be possible to treat by end-user in some case.
C It must be treated by Professional Technical Staff
Screen's display range is incorrect
Screen is distorted
Part of colors (R/G/B) is not displayed. Black line appears in vertically
Dark screen
Symptom
- 5 -

3. MAINTENANCE
3-1 LMU-TK18AG2
Disassembling the major components
(1) Cabinet
1.Unscrew to secure the cabinet (10-position)
2.Pull the cabinet upward to remove it
(2) LCD Panel
1.Unscrew to secure the LCD Panel (4-position)
2.Pull the LCD Panel and pull two connectors out from inverter unit
3.Disconnect two cables from the Main PCB
4.Unscrew to secure the earth terminal (1-position)
(3) Main PCB
1.Pull a RGB signal cable out
2.Unscrew to secure the Main PCB (7-position)
3.Disconnect the cables on the Main PCB (7-position)
/ Two connectors from the LCD Panel
/ One connector from the Switch PCB
/ One connector from the VR PCB
/ One connector from the DC-IN PCB
/ Two connectors from the Inverter PCB on LCD
4.Unscrew to secure the bracket for RGB connector (2-position)
(4) Driver PCB
1.Unscrew to secure the Driver PCB (2-position)
2.Disconnect the cable from the Inverter PCB
3.Disconnect the cable from the DC-IN PCB
(5) Connector PCB
1.Unscrew to secure the Connector PCB (2-position)
2.Disconnect the cable from the Main PCB
(6) VR PCB
1.Unscrew to secure the VR PCB (2-position)
2.Disconnect the cable from the Main PCB
(7) DC-IN PCB
1.Unscrew to secure the DC-IN PCB (2-position)
2.Disconnect three cables, one from power switch, one from Driver PCB and
one from the Main PCB
(8) Power Switch
1.Remove the power switch, while pressing the hook of the power switch
- 6 -

3-2 LMU-TK18AG2TC
Disassembling the major components
(1) Cabinet
1.Unscrew to secure the cabinet (10-position)
2.Pull the cabinet upward to remove it
(2) LCD Panel and Touch Panel
1.Unscrew to secure the bracket for Touch Panel (8-position) and remove the brackets
2.Unscrew to secure the LCD Panel (4-position)
3.Pull the Touch Panel and LCD Panel up
and pull two connectors out from inverter unit
4.Disconnect two cables from the Main PCB
5.Unscrew to secure the earth terminal (1-position)
6.Disconnect the cable on the Touch Controller PCB
(3) Main PCB
1.Pull a RGB signal cable out
2.Unscrew to secure the Main PCB (7-position)
3.Disconnect the cables on the Main PCB (8-position)
/ Two connectors from LCD Panel
/ One connector from the Switch PCB
/ One connector from the VR PCB
/ One connector from the DC-IN PCB
/ Two connectors from the Inverter PCB on LCD
/ One connector from the Touch Controller PCB
4.Unscrew to secure the bracket for RGB connector (2-position)
(4) Driver PCB
1.Unscrew to secure the Driver PCB (2-position)
2.Disconnect the cable from the Inverter PCB
3.Disconnect the cable from the DC-IN PCB
(5) Touch Controller PCB
1.Unscrew to secure the Touch Controller PCB (2-position)
2.Disconnect a serial cable
(6) Serial Cable (Connector and Cable with bracket)
1.Unscrew to secure the bracket for serial cable (2-position)
(7) Connector PCB
1.Unscrew to secure the Connector PCB (2-position)
2.Disconnect the cable from the Main PCB
(8) VR PCB
1.Unscrew to secure the VR PCB (2-position)
2.Disconnect the cable from the Main PCB
(9) DC-IN PCB
1.Unscrew to secure the DC-IN PCB (2-position)
2.Disconnect three cables, one from power switch, one from Driver PCB and
one from the Main PCB
(10) Power Switch
1.Remove the power switch, while pressing the hook of the power switch
- 7 -

Vsync.
Hsync.
Blue
DDC
Green
Red
RS232C
OSD Buttons
EEPROM
Micro
Controller LED
Video
Controller
ASIC
PLL
ROM
Video
Amp
SXGA
TFT
LCD
Panel
ADC
EEPROM
for P&P Clock Gen.
Rotary
Volume
Inverter
Touch Control Board
Touch Senser
DC/DC Conv.
Inverter
Driver
Power Supply
AMP
TOUCH CONTROLLER
ROM
Micro
Controller
NVRAM
A/D Conv.
Touch Senser Interface
Micro Controller Interface
Panel
Cont.
Main Board
4. BLOCK DIAGRAM
- 8 -

J201
DC IN P.C.B Inverter Block
Power Switch
5. Connection Diagram
TFT 18.1-inch Liquid Crystal Display
MAIN P.C.B
AC Adapter
AC Plug
VR1
Touch Screen
Touch Screen
Connector P.C.B
External OSD
Switch
Brightness Volume P.C.B
Controller P.C.B.
Personal Computer
Capacitive
Driver P.C.B
GND
RE6
GE0
GE5
BE1
BE6
GE1
BE0
BE5
GE6
BE3
GND
GND
MENU
RED
GE2
GE4
+13.5V
SEL
GE7
UP
RE3
RE0
GND
RED
RE1
RE2
RE7
RE4
DOWN
GND
GE3
BE2
GND
GND
BE4
BE7
GND
RE5
GND
N.C.
N.C.
N.C.
N.C.
N.C.
BRTL
BRTH
BRTL
GND
Shasis GND
N.C
N.C
N.C
TXD CTS RTS
RTS
CTS
RXD
TXD
RXDN.C.
GND
GND GREEN
HSYNC
N.C.
GND
GND HSYNC
N.C.
GND
GND
N.C.
GND
N.C.
VSYNC
DDCLK
N.C.
GND
GND DDDA
DDCLK
GREEN
BLUE
VSYNC
DDDA
BLUE N.C. GND
GND
+5V
N.C
N.C
DCD DTR DSR
LR
UL
UR
BACK
LL
N.C.
N.C.
GND
GND
DAO-
DAO+
GND
DA1+
DA1-
GND
DA2+
DA2-
GND
CKA+
DA3-
GND
CKA-
DA3+
GND
N.C.
PWSEL
GNDB
BRTP
BRTL
BRTH
BRTC
N.C.
N.C.
GNDB
+13.5V GND
GNDB GNDB GNDB GNDB VDDB VDDB VDDB VDDB
N.C. N.C.
CN201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CN301
1
2
3
4
5
6
7
8
CN2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CN203
1
2
CN100
8
15
7
14
6
13
5
12
4
11
3
10
2
9
1
CN201
1
2
Mini D-SUB 15pin
VGA
8 15 7 14 6 13 5 12 4 11 3 10 2 9 1
CN400
1
2
CN7
1
2
3
4
5
6
7
CN502
1
2
3
4
5
CN501
1
2
3
4
5
CN401
1 2
5
9
4
8
3
7
2
6
1
5
9
4
8
3
7
2
6
1
D-SUB 9PIN SERIAL PORT
5 9 4 8 3 7 2 6 1
JP1
1
2
3
4
5
6
7
8
9
10
11
12
CN1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN200
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN202
1
2
3
4
5
6
7
8
9
CN450
1
2
3
4
5
6
7
8
9
CN1
1 2
CN202
1
2
CN451
1
2
3
4
5
CN2
1 2 3 4 5 6 7 8
CN201
1 2 3 4 5 6 7 8
CN101
1
2
3
- 9 -

6. TABLE OF SIGNAL NAME
Symbol
Signal Name
Location
Notes
RED RED/Analog Video Signal CN100-1
GREEN
GREEN/Analog Video Signal
CN100-2
BLUE
BLUE/Analog Video Signal
CN100-3
DDDA(ID1)
DDC Data
CN100-12
HSYNC
Horizontal Synchronizing Signal
CN100-13
VSYNC
Vertical Synchronizing Signal
CN100-14
DDCK(ID3)
DDC Data Clock
CN100-15
DB0-
Pixel Data-Even
CN200-5
LVDS level
DB0+
Pixel Data-Even
CN200-6
LVDS level
DB1-
Pixel Data-Even
CN200-8
LVDS level
DB1+
Pixel Data-Even
CN200-9
LVDS level
DB2-
Pixel Data-Even
CN200-11
LVDS level
DB2+
Pixel Data-Even
CN200-12
LVDS level
CKB-
Pixel Clock-Even
CN200-14
LVDS level
CKB+
Pixel Clock-Even
CN200-15
LVDS level
DB3-
Pixel Data-Even
CN200-17
LVDS level
DB3+
Pixel Data-Even
CN200-18
LVDS level
DA0-
Pixel Data-Even
CN201-5
LVDS level
DA0+
Pixel Data-Even
CN201-6
LVDS level
DA1-
Pixel Data-Even
CN201-8
LVDS level
DA1+
Pixel Data-Even
CN201-9
LVDS level
DA2-
Pixel Data-Even
CN201-11
LVDS level
DA2+
Pixel Data-Even
CN201-12
LVDS level
CKA-
Pixel Clock-Even
CN201-14
LVDS level
CKA+
Pixel Clock-Even
CN201-15
LVDS level
DA3-
Pixel Data-Even
CN201-17
LVDS level
DA3+
Pixel Data-Even
CN201-18
LVDS level
BRTC
B/BL/on/off
CN450-4
H: Back Light On
L: Back Light Off
BRTH
CN450-5
BRTL
CN450-6
BRTP
CN450-7
PWSEL
PWM select signal
CN450-9
BRTH
CN450-5
BRTL
CN450-6
BRTP
CN450-7
MENU
Menu Key Input
CN301-1
SEL
Select Key Input
CN301-2
DOWN
Down Key Input
CN301-3
UP
Up Key Input
CN301-4
- 10 -

TouchScreen Controller
(for LMU-TK18AG2TC only)
RTS
Repuest To Send
JP1-1
RXD
Receive Data
JP1-2
TXD
Transmit Data
JP1-3
CTS
Clear To Send
JP1-4
DCD
Data Carrier Detect
NC
DTR
Data Terminal Ready
NC
GND
Signal ground
NC
DSR
Data Set Ready
NC
GND
Chassis (earth) ground
NC
UR
Upper right (UR) corner
JP2-9
LR
Lower right (LR) corner
JP2-10
UL
Upper left (UL) corner
JP2-11
LL
Lower left (LL) corner
JP2-12
- 11 -

7. EXPLODED VIEW
AND PARTS LIST
7-1 Exploded view
- 12 -

7-2 Parts List
CAUTION
Parts marked as Are very important to secure safety.
In case of replacement, it is required to use designted parts for safety.
7-2-1 LMU-TK18AG2
REF No.
PART No.
DESCRIPTION
Q'ty
NOTES
OUTER
661 006 5927
OUTER CARTON
1
INDIVIDUAL
661 004 2409
PAD, TOP
1
632 892 5001
ACCESSORY CASE
1
632 892 5018
PAD, ACCESSORY
1
661 006 5934
PAD, CONER UPPER
4
661 006 5941
PAD, CONER LOWER
4
632 878 8637
POLYETHYLENE BAG, 550X700
1
FOR MONITOR
632 603 0998
POLYETHYLENE BAG, 130X500
1
FOR AC COAD
632 298 2376
POLYETHYLENE BAG
1
FOR CNT BOX
632 607 4824
POLYETHYLENE BAG, L 180X270
1
FOR USER'S GUIDE
632 567 2588
POLYETHYLENE BAG, 200X300
1
FOR RGB CABL
ACCESSORY
661 006 5903
INSTRUCTION MANUAL, ENGLISH
1
CABINET1
1
661 012 7915
CABINET ASSY
1
13
661 006 5958
RATING PLATE
1
CHASSIS
11
661 012 7922
CHASSIS ASSY, BOTTOM
1
CHASSIS ELC.
4
661 012 7939
LCD ASSY
1
16
661 012 7946
AC ADAPTER ASS'Y
1
2
661 012 7953
WIRE HANESS ASSY
1
17
632 872 9494
VGA CABLE, 1.5M
1
12
661 012 7960
SWITCH ASSY
1
14
661 001 3164
REMOCON ASSY
1
PC BOARD
6
661 012 7977
PCB-ML ASSY, MAIN
1
10
661 012 7984
PCB ASSY, VR1
1
9
661 012 7991
PCB-W ASSY, DC-IN
1
7
661 012 8004
PCB ASSY, DRIVER
1
8
661 012 8011
PW BOARD ASS'Y, JOINT
1
- 13 -

CAUTION
Parts marked as ! Are very important to secure safety.
In case of replacement, it is required to use designted parts for safety.
7-2-2 LMU-TK18AG2TC
REF No.
PART No.
DESCRIPTION
Q'ty
NOTES
OUTER
661 006 5927
OUTER CARTON
1
INDIVIDUAL
661 004 2409
PAD, TOP
1
632 892 5001
ACCESSORY CASE
1
632 892 5018
PAD, ACCESSORY
1
661 006 5934
PAD, CONER UPPER
4
661 006 5941
PAD, CONER LOWER
4
632 878 8637
POLYETHYLENE BAG, 550X700
1
FOR MONITOR
632 603 0998
POLYETHYLENE BAG, 130X500
1
FOR AC COAD
632 298 2376
POLYETHYLENE BAG
1
FOR CNT BOX
632 607 4824
POLYETHYLENE BAG, L 180X270
1
FOR USER'S GUIDE
632 567 2588
POLYETHYLENE BAG, 200X300
1
FOR RGB CABL
632 607 4824
POLYETHYLENE BAG, L 180X270
1
FOR SERIAL CABLE
ACCESSORY
661 006 5903
INSTRUCTION MANUAL, ENGLISH
1
632 867 2325
CD-ROM DISK, TOUCHWARE
1
CABINET1
1
661 012 9087
CABINET ASSY
1
13
661 006 5989
RATING PLATE
1
CHASSIS
11
661 012 9094
CHASSIS ASSY, BOTTOM
1
CHASSIS ELC.
4
661 012 9100
LCD ASSY
1
3
661 012 9131
TOUCH SENSOR ASSY
1
5
661 012 9148
SERIAL CONTROLLER ASSY
1
16
661 012 7946
AC ADAPTER ASSY
1
2
661 012 7953
WIRE HANESS ASSY
1
17
632 872 9494
VGA CABLE, 1.5M
1
15
661 012 9117
CABLE ASSY
1
12
661 012 7960
SWITCH ASSY
1
14
661 001 3164
REMOCON ASSY
1
PC BOARD
6
661 012 9124
PCB-ML ASSY, MAIN
1
10
661 012 7984
PCB ASSY, VR1
1
9
661 012 7991
PCB-W ASSY, DC-IN
1
7
661 012 8004
PCB ASSY, DRIVER
1
8
661 012 8011
PW BOARD ASS'Y, JOINT
1
- 14 -

APPENDIX
Version of Firmware
The Version of Firmware is displayed on screen.
Turn the Power Switch to ‘OFF’. While pressing of the [ENTER] button, turn the Power
Switch to ‘ON’.
- 15 -