Sanyo VMC-8621P User manual

FILE NO.
REFERENCE No.SM5310339
L8MZ5/XE,UK,AU
NOTE: 1. Parts order must contain model number, part number, and description.
2. Substitute parts may be supplied as the service parts.
3. N.S.P. : Not available as service parts.
Design and specifications are subject to change without notice.
SERVICE MANUAL
Colour Video Monitor
CONTENTS
SPECIFICATIONS .................................................................... 2
1. OPERATING INSTRUCTIONS ............................................. 3
2. SERVICE ADJUSTMENTS ................................................... 5
3. PARTS LIST ......................................................................... 8
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS...........C1
(Product Code : 114 951 30)
(Europe)
VMC-8621P
(Product Code : 114 951 31)
(U.K.)
(Product Code : 114 951 32)
(Australia)
The components designated by a symbol ( ) in this schematic diagram designates components whose value are of
special significance to product safety. Should any component designated by a symbol need to be replaced, use only the
part designated in the Parts List. Do not deviate from the resistance, wattage, and voltage ratings shown.
PRODUCT SAFETY NOTICE

– 2 –
PAL/NTSC, selected automatically
21 inch
More than 450 TV lines
Separate Y/C signal, mini-DIN connector (1)
Y signal: 1.0 Vp-p, 75 ohm negative sync
C signal: 0.286 Vp-p, 75 ohm negative sync, bridge connection possible
Composite sync signal: 1.0 Vp-p, 75 ohm BNC connector (2)
Audio signal: -6dBs (400 mVrms), RCA pin (3), bridge connection possible
Separate Y/C signal, mini-DIN connector (1)
Y signal: 1.0 Vp-p, 75 ohm negative sync
C signal: 0.286 Vp-p, 75 ohm negative sync, bridge connection possible
Composite sync signal: 1.0 Vp-p, 75 ohm BNC connector (2),
automatic temination setting
Audio signal: -6dBs (400 mVrms), RCA pin (3), bridge connection possible
YES
1 W
Oval speaker x 1
100 to 240 V AC, 50/60 Hz
95 Watts
-10 °C to 45 °C storage temperature
10 % to 90 %
492 x 474 x 482 mm
29kg
SPECIFICATIONS
Color system :
Picture tube :
Resolution :
Input terminals :
Outout terminals :
Overscan or underscan selection:
Audio output :
Speaker :
Power source :
Power consumption :
Ambient operating temperature :
Ambient operating humidity :
Dimension (W x H x D ) :
Weight :
Fig. 1
W
H
D

–3 –
Fig. 2
1. Speaker
When the monitor selector button (A, B or Y/C)
is pressed, the speaker lets you hear the sound
from the components which are connected to
the terminals at the rear of the monitor. (Use
components which produce audio output.)
2. On-screen display button (OSD)
When this button is pressed, the menu screen
appears on the monitor screen.
3. Cursor ( ) button ( )
When this button is pressed, the cursor moves
down. When it reaches the bottom, it reappears
at the top. In addition, this button is used to
make adjustment values smaller.
4. Cursor ( ) button ( )
When this button is pressed, the cursor moves
up. When it reaches the top, it reappears at the
bottom. In addition, this button is used to make
adjustment values larger.
5. Display selector button (ENTER)
If this button is pressed while a picture is on the
monitor screen, the screen changes to the
adjustment screen. If the button is pressed once
more, the picture returns to the previous screen.
1. OPERATING INSTRUCTIONS
1-1. FRONT PANEL CONTROLS
245 67G
3F
1
SCAN
9
8
1.COLOR
2.TINT
3.BRIGHTNESS
4.CONTRAST
5.SHARPNESS
6.VOLUME
7.DWELL TIME
8.LANGUAGE
9.TITLE
10.VERSION
EXIT : OSD
6. Underscan/overscan select button (SCAN)
The initial setting is for the normal screen
(overscan). If the SCAN button is pressed, the
screen will become smaller (underscan) than
the normal screen. Change this setting in cases
such as when screen display characters are
missing. If the SCAN button is pressed once
more, the normal screen is displayed again.
7. Monitor A selector button (A)
When this button is pressed, the audio and
video input changes to the component which is
connected to the A terminals at the rear of the
monitor.
8. Monitor B serector button (B)
When this button is pressed, the audio and
video input changes to the component which is
connected to the B terminals at the rear of the
monitor.
9. Monitor Y/C selector button (Y/C)
When this button is pressed, the audio and
video input changes to the component which is
connected to the Y/C terminals at the rear of the
monitor.
10. Power indicator (POWER)
Lights when the power is on.
11. Power button (POWER)
Press this button to turn the power on and off.

–4 –
23 4
1
Fig. 4
1-2. REAR PANEL CONTROLS & CONNECTION
1. AC INPUT socket
Connect the AC power cord (supplied) securely
to this socket and to a wall outlet.
2. Rear A terminals (AUDIO/VIDEO A terminals)
When the monitor A selector button at the front
of the monitor is pressed, the audio and video
signals from the component which is connected
to these terminals can be monitored.
3. Rear B terminals (AUDIO/VIDEO B terminals)
When the monitor B selector button at the front
of the monitor is pressed, the audio and video
signals from the component which is connected
to these terminals can be monitored.
4. Rear Y/C terminals (AUDIO/VIDEO Y/C
terminals)
When the monitor Y/C selector button at the
front of the monitor is pressed, the audio and
video signals from the component which is
connected to these terminals can be monitored.
Fig. 3
Y/C (Mini DIN 4 pin) terminal specification
Pin No. Signal
1 GND (Y)
2 GND (C)
3Y
4C
OUT
IN
4
2
3
1
4
2
3
1

–5 –
ADJUSTMENT
ITEM
TIMING
PATTERN SETTING VR
LOCATION ADJUSTMENT PROCEDURE
CHECK B+
VOLTAGE
HOLD DOWN
VOLTAGE
SETTING
FOCUS
ADJUSTMENT
HORIZONTAL
PHASE
ADJUSTMENT
HORIZONTAL
SIZE
ADJUSTMENT
VERTICAL
LINEARY
ADJUSTMENT
VERTICAL
CENTER
ADJUSTMENT
VERTICAL
SIZE
ADJUSTMENT
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
PATTERN GENERATOR
MONOSCOPE PATTERN
TEST POINT : D910(-)
DIGITAL VOLT METER
VALUE 125.5 ±0.5 VDC.
TEST POINT : ZD501(-)
DIGITAL VOLT METER
VALUE 8.75 ±0.1 VDC.
Adjusting FBT Focus VR make focus
resolution of reach over 450TV lines, four
corners must be aiso clear.
Adjusting VR401 horizontal phase make
right and left of picture to <=1%.
Adjusting VR306 make signal side of
picture of scale at 1.5 ~ 2.2 position.
Adjusting vertical linear control VR302 for
equal spacing of lines between center
extreme of scan [(Max-Min)/Aver-
age]<=10%.
Adjusting vertical center control VR303 to
<=1%.
Adjusting vertical size control VR301
make signal side of scale is 1.0 ~ 1.5
position.
VR503
FTB FOCUS
VR
VR401
VR306
VR302
VR303
VR301
BRIGHT VR and
CONTRAST VR
TO MAX.
BRIGHT VR and
CONTRAST VR
TO 75%.
SHARPNESS
VR TO MAX.
BRIGHT VR ,
CONTRAST VR
and SHARP-
NESS VR TO
MAX.
BRIGHT VR ,
CONTRAST VR
and SHARP-
NESS VR TO
MAX.
BRIGHT VR ,
CONTRAST VR
and SHARP-
NESS VR TO
MAX.
BRIGHT VR ,
CONTRAST VR
and SHARP-
NESS VR TO
MAX.
BRIGHT VR ,
CONTRAST VR
and SHARP-
NESS VR TO
MAX.
2. SERVICE ADJUSTMENTS
1. Supply power to the set and measuring instruments and allow to warm up for at least 30 minutes.
NOTE
Be sure to use a non-metallic driver for adjusting there VRs. A metallic driver can cause damage by shorting.
Adjustment tool
1. Digital multi meter
2. Pattern generator
3. Color analyzer
Adjustment mode
Over scan mode

–6 –
ADJUSTMENT
ITEM
TIMING
PATTERN SETTING VR
LOCATION ADJUSTMENT PROCEDURE
WHITE BAL-
ANCE AD-
JUSTMENT
LUMINANCE
ADJUSTMENT
PATTERN GENERATOR
NO SIGNAL
PATTERN GENERATOR
FULL WHITE
PATTERN GENERATOR
NO SIGNAL
PATTERN GENERATOR
WINDOWS PATTERN
PATTERN GENERATOR
FULL WHITE
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
VR801,VR803,
VR805,
FBT FOCUS
VR
VR804,VR802,
VR501
FBT SCREEN
VR
VR501
VR502
Adjust VR805 G-Bias to center.
Adjust FBT screen VR make luminance
without video to 2.0 ~ 4.0 FL.
Adjust VR801 make X value is 0.313 ±
0.015.
Adjust VR803 make Y value is 0.329 ±
0.015.
Adjust VR501 make luminance with video
signal to 49 ~ 55 FL.
Adjust VR804 make X value is 0.313 ±
0.015.
Adjust VR802 make Y value is 0.329 ±
0.015.
Adjust FBT screen VR make luminance
without video signal is 2.0 ~ 4.0 FL.
Adjust VR501 make luminance is 49 ~ 55
FL.
Adjust VR502 make luminance is 110 ±
10 FL.
Then make sure Full White luminance
whether it is 49 ~ 55 FL.
ADJUSTMENT
ITEM
TIMING
PATTERN SETTING VR
LOCATION ADJUSTMENT PROCEDURE
WHITE BAL-
ANCE AD-
JUSTMENT
and
LUMINANCE
ADJUSTMENT
PATTERN GENERATOR
NO SIGNAL
PATTERN GENERATOR
FULL WHITE
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
BRIGHT VR ,
CONTRAST VR
and SHARPNESS
VR TO MAX.
VR801,VR802,
VR803,VR804,
VR805,
FBT SCREEN
VR
VR804,VR802,
VR501
VR801,VR802,VR803,VR804 and VR805
is center position.
Adjust the VR801, VR803 and FBT
SCREEN VR to dark gray with screen.
Adjust the VR802 and VR804 to white
gray with screen.
Adjust the VR501 it makes the screen of
the monitor proper brightness.
The way of adjusting it which a color analyzer is not used for.

–7 –
10 987
6
5
4
3
2
1
11
12
13
T502
VR401
VR501
VR503
VR303
IC202
1
IC301
1
VR301 VR302
T902
VR306
S108
S107 LED101
S106
S104
S101
S103 S102
S105
VR804
VR805
VR801
VR802
VR803
Q804
Q802
Q806
F901
V-LIN
V-SIZE
V-CENTER ABL
H-SIZE
X-RAY H-PHASE
R-GAIN
R-BAISB-BAIS
G-BAIS
B-GAIN
D910
ZD501
Fig. 4
Fig. 5 Fig. 6
MAIN BOARD
(Parts side)
FUNCTION BOARD
(Parts side)
VIDEO BOARD
(Parts side)

8
3. PARTS LIST
N.S.P.: Not available as service parts.
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
ACCESSORIES & PACKING MATERIALS
645 052 5339 USER MANUAL VMC-8621P
645 034 3971 POWER CORD 10-1 VDE,
VMC-8621P(Erope) ONLY
645 040 9264 POWER CORD NS8-5181N,
VMC-8621P(U.K.) ONLY
645 040 9257 POWER CORD NS8-5180 NAUSTR,
VMC-8621P (Australia) ONLY
645 038 5605 NYLON CABLE TIE 2.5*120MM
645 046 5710 NYLON CABLE TIE 2.5*200MM
645 052 5315 CARTON VMC-8621P PAL
645 046 5833 PE BAG CM-21DXA 64*48*110CM
645 052 5377 POLYFORM CM-21DXA
CABINET & CHASSIS PARTS
1 645 052 5346 FRONT PANEL CM-21DXA
2 645 052 5322 DIGITAL STICKER VMC-8621P
3 645 052 5353 SPEAKER PANEL VMC-8621P
4 645 048 3493 SW KNOB 19"” AA-51
5 645 048 3516 CONTROL PANEL 14"” AA-51
6 645 046 6458 SW ASS’Y CH-19DXA
7 645 052 5520 FUNCTION BOARD VMC-8621P
8 645 034 3605 RH W/W SCR. 3*8MM
9 645 046 4829 PH SCREW 3*8MM
10 645 046 6441 SPKR S9711-22NQ4171C 8OHM/1W
11 645 046 4829 PH SCREW 3*8MM
12 645 046 4874 BH SCREW 3*12MM
13 645 052 5438 BRACKET RIGHT CM-21DXA
14 645 052 5445 BRACKET LEFT CM-21DXA
15 645 046 4836 PH SCREW 4*12MM
16 645 052 5384 CRT A51AEZ90X01 CPT
17 645 046 4928 RUBBER WASHERDIA20*DIA6*1T
18 645 046 4966 WASHER 6.5*19*1MM
19 645 046 4843 PH SCREW 6*12MM
20 645 052 5414 DEGAUSSING COIL CM-21DUA
21 645 055 0386 VIDEO BOARD CM-21DUA
22 645 052 5469 METAL TOP COVER CM-21DXA
23 645 034 3919 HANDLE COVER CM-14 PA-765A
24 645 034 3582 PH W/W SCR. 4*8MM
25 645 034 3841 ID LABEL 83*51MM (N.S.P.)
26 645 034 3612 SCREW+WASHER 3*6MM
27 645 052 5513 MAIN BOARD CM-21DUA
28 645 046 0722 PCB GUIDE RAIL MM-9M
29 645 034 4299 PCB GUIDE RAIL MM-12A
30 645 052 5452 BASE CM-21DUA
32 645 034 4657 FOOT PAD GL-24H
31 645 034 3582 PH W/W SCR. 4*8MM
33 645 034 3926 FOOT PAD RIVET MM-12A GL-24H
34 645 046 6236 REPAIR PLATE CH-19DXA
35 645 046 4850 PH W/W SCR. 3*6MM
36 645 048 3585 SPACER SUPPORTS FCT-14
37 645 046 6380 SHIELDING PLATE DXA SERIES
38 645 046 6731 SIGNAL BOARD CM-21DXA
39 645 046 6373 GND PLATE DX 20*13*0.5MM
40 645 046 6281 JACK PLATE BRACKET CM-21DXA
41 645 046 6526 AC SOCKET ASS’Y MM-20A
42 645 035 6216 BH SCREW 4*6MM
43 645 035 6223 WASHER OUT TEETH 4.5*8.5*0.5MM
44 645 052 5476 JACK PLATE CM-21DUA
45 645 046 4850 PH W/W SCR. 3*6MM
46 645 048 3448 SLOT COVER 150*9MM AA-51
47 645 040 9226 X RADIATION LABEL 110*50MM
15
13
1
3
2
456
78
9
46 14 12
1011
31
30
29
28
33
34
35
36 44
43
42
41
40
39
38
37
45
48
26
27
24
21 22
23
25
32
47
16 17
1819
20

9
ELECTRICAL PARTS
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
Note:
1. Materials of Capacitors and Resistors are abbreviated as follows ;
Resistors Capacitors
CF RES Carbon Film Resistor MEF CAP Metallized Polyester Film Capacitor
MF RES Metal Film Resistor (Non-inductive)
MOF RES Metallized Oxide Film Resistor MEMB CAP Mini Box Metallized Polyester Capacitor
(Non-inductive)
PEI CAP Polyester Film Capacitor (Inductive)
PPN CAP Polypropylene Film Capacitor (Non-inductive)
PPS CAP Polypropylene and Metallized Polypropylene
Film Capacitor (Non-inductive)
MPP CAP Metallized Polypropylene Capacitor
(Non-inductive)
X CAP(MKP) Metallized Polypropylene Film Capacitor
(Non-inductive)
CC CAP Ceramic Capacitor
EC CAP Electrolytic Capacitor
2. N.S.P. : Not available as service parts.
SW ASS’Y CH-19DXA
645 046 6458
(SWITCH)
645 046 5086 POWER SWITCH PS3-22SP-W4CW
(MISCELLANEOUS)
645 051 0779 L/W HOUSING 1015 18AWG L=460MM (N.S.P.)
AC SOCKET ASS’Y MM-20A
645 046 6526
(SOCKET)
645 034 3988 POWER SOCKET SS-120E
(MISCELLANEOUS)
645 046 5550 L/W HOUSING B/G&Y/B 1015 18AWG (N.S.P.)
645 046 5376 LEAD WIRE 1015 18AWG (N.S.P.)
VIDEO BOARD CM-21DUA
645 055 0386
(CAPACITORS)
C801 645 055 0119 EC CAP. 100UF 25V 105C
C803 645 046 3877 CC CAP. 391PF 50V Y5P
C804 645 046 3877 CC CAP. 391PF 50V Y5P
C805 645 046 3877 CC CAP. 391PF 50V Y5P
C806 645 043 3139 CC CAP. 103PF 1.5KV Z5U
(TRANSFORMER)
Q801 645 034 3216 TR 2SC1815GR
Q802 645 040 9110 TR 2SC2688L
Q803 645 034 3216 TR 2SC1815GR
Q804 645 040 9110 TR 2SC2688L
Q805 645 034 3216 TR 2SC1815GR
Q806 645 040 9110 TR 2SC2688L
(RESISTORS)
R801 645 034 2462 MOF RES. 12KOHM 3W +/-5%
R803 645 034 2141 CF RES. 3.3KOHM 1/4W +/-5%
R804 645 034 2028 CF RES. 220OHM 1/4W +/-5%
R805 645 034 2141 CF RES. 3.3KOHM 1/4W +/-5%
R808 645 034 2141 CF RES. 3.3KOHM 1/4W +/-5%
R809 645 034 2028 CF RES. 220OHM 1/4W +/-5%
R810 645 034 2141 CF RES. 3.3KOHM 1/4W +/-5%
R813 645 034 2141 CF RES. 3.3KOHM 1/4W +/-5%
R814 645 046 2665 CF RES. 360OHM 1/4W +/-5%
R815 645 034 2141 CF RES. 3.3KOHM 1/4W +/-5%
R816 645 046 3235 MOF RES. 220KOHM 1/2W +/-5%
R817 645 034 2462 MOF RES. 12KOHM 3W +/-5%
R819 645 034 2417 MF RES. 2.2KOHM 1/2W +/-1%
R824 645 034 2417 MF RES. 2.2KOHM 1/2W +/-1%
R825 645 034 2462 MOF RES. 12KOHM 3W +/-5%
R826 645 034 2417 MF RES. 2.2KOHM 1/2W +/-1%
(VARIABLE RESISTORS)
VR801 645 046 4805 POT VR 5KOHM 6DIA
VR802 645 046 4768 POT VR 300OHM 6DIA
VR803 645 046 4805 POT VR 5KOHM 6DIA
VR804 645 046 4768 POT VR 300OHM 6DIA
VR805 645 046 4805 POT VR 5KOHM 6DIA
(SPARK GAPS)
SGP801 645 038 5520 SPARK GAP 250V +/-20%
SGP802 645 038 5520 SPARK GAP 250V +/-20%
SGP803 645 038 5520 SPARK GAP 250V +/-20%
(MISCELLANEOUS)
W801 645 034 3773 CONNECTOR BASE M241855 (N.S.P.)
W802 645 034 3759 CONNECTOR BASE M241854-X (N.S.P.)
G2 645 034 3667 CONNECTOR BASE P235142 (N.S.P.)
GND1 645 034 3698 CONNECTOR BASE M11352 (N.S.P.)
SK801 645 040 9240 CRT SOCKET ISHM35S
MAIN BOARD CM-21DUA
645 052 5513
(CAPACITORS)
C101 645 034 2806 EC CAP. 4.7UF 50 V
C102 645 034 2837 CC CAP. 104PF 50V Y5V
C103 645 034 2714 EC CAP. 220UF 16 V
C104 645 046 3853 CC CAP. 33PF 50V Y5P
C105 645 046 3853 CC CAP. 33PF 50V Y5P
C107 645 044 3695 EC CAP. 10UF 50 V
C108 645 044 3695 EC CAP. 10UF 50 V
C109 645 044 3695 EC CAP. 10UF 50 V
C110 645 051 0946 EC CAP. 330UF 16 V
C111 645 044 3695 EC CAP. 10UF 50 V
C112 645 044 3695 EC CAP. 10UF 50 V
C120 645 046 3853 CC CAP. 33PF 50V Y5P
C121 645 046 3853 CC CAP. 33PF 50V Y5P
C122 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C123 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C124 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C125 645 034 2837 CC CAP. 104PF 50V Y5V
C126 645 034 2738 EC CAP. 2.2UF 50 V
C127 645 034 2837 CC CAP. 104PF 50V Y5V
C128 645 034 2677 EC CAP. 1UF 50 V
C130 645 034 2738 EC CAP. 2.2UF 50 V
C218 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C219 645 046 4003 PEI CAP. .022UF 100V +/-5%
C221 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C222 645 044 3695 EC CAP. 10UF 50 V
C223 645 045 9962 EC CAP. 47UF 25 V
C224 645 034 3049 MEMB CAP. .47UF 63V +/-5%
C225 645 044 3695 EC CAP. 10UF 50 V
C226 645 055 0171 EC CAP. 2.2UF 50 V

10
LOCATION PARTS NO. DESCRIPTION LOCATION PARTS NO. DESCRIPTION
C926 645 034 3025 MEMB CAP. .22UF 63V +/-5%
C928 645 055 0102 EC CAP. 100UF 16 V
C929 645 034 2837 CC CAP. 104PF 50V Y5V
C930 645 046 3617 EC CAP. 1000UF 16 V
C931 645 046 3761 EC CAP. 470UF 25 V
C932 645 034 2837 CC CAP. 104PF 50V Y5V
C933 645 055 0164 EC CAP. 2200UF 10V 10DIA
C936 645 055 0232 EC CAP. 47UF 250V 13DIA
C937 645 055 0263 MEMB CAP. .0056UF 100V +/-5%
(DIODES)
D101 645 034 3308 DIODE 1N4148
D102 645 034 3308 DIODE 1N4148
D103 645 034 3308 DIODE 1N4148
D104 645 034 3308 DIODE 1N4148
D107 645 034 3308 DIODE 1N4148
D110 645 034 3308 DIODE 1N4148
D209 645 034 3308 DIODE 1N4148
D210 645 034 3308 DIODE 1N4148
D211 645 034 3308 DIODE 1N4148
D212 645 034 3308 DIODE 1N4148
D213 645 034 3308 DIODE 1N4148
D301 645 034 3377 RECTIFIER DIODE 1N4003
D403 645 046 6960 PARTS ASS’Y
D404 645 046 6960 PARTS ASS’Y
D502 645 034 3308 DIODE 1N4148
D503 645 034 3308 DIODE 1N4148
D504 645 040 9141 RECTIFIER DIODE PG102R
D505 645 046 2320 CF RES. 15KOHM 1/6W +/-5%
D511 645 046 0234 RECTIFIER DIODE PG106R
D901 645 046 4706 RECTIFIER DIODE PG5407
D902 645 046 4706 RECTIFIER DIODE PG5407
D903 645 046 4706 RECTIFIER DIODE PG5407
D904 645 046 4706 RECTIFIER DIODE PG5407
D905 645 034 3346 RECTIFIER DIODE BYT52M
D906 645 040 9141 RECTIFIER DIODE PG102R
D907 645 046 0234 RECTIFIER DIODE PG106R
D908 645 034 3308 DIODE 1N4148
D909 645 034 3308 DIODE 1N4148
D910 645 046 0272 RECTIFIER DIODE BYT56J
D911 645 040 9165 RECTIFIER DIODE 31DF4
D912 645 046 0272 RECTIFIER DIODE BYT56J
D913 645 040 9165 RECTIFIER DIODE 31DF4
D914 645 034 3346 RECTIFIER DIODE BYT52M
D915 645 055 0317 RECTIFIER DIODE 30DF2 52MM
D916 645 046 0272 RECTIFIER DIODE BYT56J
ZD201 645 046 4614 ZENER DIODE HZ5C1
ZD501 645 046 4621 ZENER DIODE HZ9C1
ZD901 645 034 3339 ZENER DIODE HZ22-2
(FUSES)
F901 645 038 5650 FUSE 3.15A/250V SLOWBLOW 5*20
(FUSE RES)
FR901 645 055 0072 FUSE RES. 1OHM 1/4W +/-5%
FR902 645 055 0089 FUSE RES. 1OHM 1/2W +/-5%
(IC)
IC101 645 046 4409 LINEAR IC NT68P61A
IC102 645 046 4416 LINEAR IC 24LC02B
IC103 645 046 4423 LINEAR IC STV9427
IC104 645 046 4355 TTL IC SN74LS74AN
IC202 645 046 4430 LINEAR IC TDA8361
IC203 645 046 4447 LINEAR IC TDA4665
IC301 645 046 4454 LINEAR IC TDA3654
IC701 645 034 3124 LINEAR IC TDA7056B
IC901 645 034 3094 LINEAR IC UC3842AN
IC902 645 034 3179 REGULATOR IC KA431Z
IC903 645 046 4379 LINEAR IC TLP721F
IC904 645 046 4492 REGULATOR IC LM317T
IC906 645 046 4478 REGULATOR IC MC7805
(COILS)
L402 645 034 4480 LINEARITY COIL 60 UH +/-20%
L405 645 055 0362 CHOKE COIL 0.5 MH +/-10%
L901 645 046 0876 CHOKE COIL 20 UH +/-20%
L902 645 046 0876 CHOKE COIL 20 UH +/-20%
L903 645 046 0876 CHOKE COIL 20 UH +/-20%
L904 645 046 0876 CHOKE COIL 20 UH +/-20%
L905 645 046 0876 CHOKE COIL 20 UH +/-20%
(TRANSFORMER)
Q101 645 034 3216 TR 2SC1815GR
C227 645 055 0249 EC CAP. 470UF 16V +/-20%
C228 645 034 2783 EC CAP. 470UF 16 V
C229 645 045 9962 EC CAP. 47UF 25 V
C230 645 034 2837 CC CAP. 104PF 50V Y5V
C231 645 046 3983 PEI CAP. .0018UF 50V +/-5%
C232 645 046 3983 PEI CAP. .0018UF 50V +/-5%
C233 645 046 3952 PEI CAP. .001UF 100V +/-5%
C234 645 046 3952 PEI CAP. .001UF 100V +/-5%
C235 645 034 2967 PEI CAP. .0047UF 50V +/-5%
C236 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C237 645 046 3921 CC CAP. 20PF 50V +/-5%
C238 645 046 3921 CC CAP. 20PF 50V +/-5%
C239 645 034 2950 PEI CAP. .022UF 50V +/-5%
C240 645 034 2738 EC CAP. 2.2UF 50 V
C241 645 055 0188 EC CAP. 33UF 50 V
C250 645 055 0096 EC CAP. 10UF 50 V
C260 645 055 0249 EC CAP. 470UF 16V +/-20%
C301 645 046 4027 PEI CAP. .0033UF 50V +/-5%
C302 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C303 645 055 0157 EC CAP. 1UF 50 V
C304 645 040 8915 EC CAP. 3300UF 25V +/-20%
C307 645 046 3952 PEI CAP. .001UF 100V +/-5%
C308 645 034 2967 PEI CAP. .0047UF 50V +/-5%
C309 645 040 8984 PEI CAP. .001UF 50V +/-5%
C310 645 046 3990 PEI CAP. .0022UF 50V +/-5%
C311 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C312 645 052 1263 EC CAP. 100UF 35 V
C312A 645 051 0731 PEI CAP. .015UF 50V +/-5%
C313 645 055 0140 EC CAP. 1000UF 35 V
C316 645 055 0225 EC CAP. 47UF 50 V
C401 645 046 4041 PEI CAP. .056UF 50V +/-5%
C402 645 055 0218 EC CAP. 47UF 25 V
C403 645 052 5254 CC CAP. 681PF 1KV Y5P
C409 645 055 0195 EC CAP. 33UF 160 V
C410 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C411 645 046 4256 PL CAP. .0027UF 100V +/-2%
C412 645 034 2967 PEI CAP. .0047UF 50V +/-5%
C413 645 034 2677 EC CAP. 1UF 50 V
C422 645 052 5308 PPS CAP. .0047UF 1.6KV +/-5%
C423 645 046 0067 PPN CAP. .018UF 630V +/-5%
C424 645 052 5261 MEF CAP. .22UF250V +/-5%22.5MM
C425 645 046 4096 MEF CAP. 10UF100V+/-10% 27.5MM
C428 645 052 5278 MEF CAP. .33UF250V +/-5%22.5MM
C429 645 052 5292 PPS CAP. .0022UF 1.6KV +/-5%
C501 645 046 4126 MEF CAP. .22UF 100V +/-5%
C502 645 055 0096 EC CAP. 10UF 50 V
C504 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C505 645 055 0171 EC CAP. 2.2UF 50 V
C506 645 055 0171 EC CAP. 2.2UF 50 V
C507 645 046 4058 PEI CAP. .068UF 50V +/-5%
C508 645 055 0171 EC CAP. 2.2UF 50 V
C706 645 034 3049 MEMB CAP. .47UF 63V +/-5%
C708 645 055 0201 EC CAP. 3300UF 10 V
C901 645 034 3070 X CAP. .1UF 250V +/-10%
C902 645 034 3070 X CAP. .1UF 250V +/-10%
C903 645 034 3087 Y CAP. 472PF 400V +/-20%
C904 645 034 3087 Y CAP. 472PF 400V +/-20%
C905 645 046 3693 EC CAP. 220UF 400V 25*40MM
C906 645 034 2974 MEF CAP. .1UF 630V +/-5%
C907 645 052 1263 EC CAP. 100UF 35 V
C909 645 038 5407 CC CAP. 561PF 50V Y5P
C910 645 055 0256 PEI CAP. .0047UF 100V +/-5%
C911 645 055 0263 MEMB CAP. .0056UF 100V +/-5%
C912 645 046 4287 MEMB CAP. .1UF 63V +/-5%
C913 645 055 0102 EC CAP. 100UF 16 V
C914 645 046 4058 PEI CAP. .068UF 50V +/-5%
C915 645 034 3087 Y CAP. 472PF 400V +/-20%
C916 645 046 3860 CC CAP. 331PF 50V Y5P
C917 645 055 0126 EC CAP. 100UF 250 V
C918 645 055 0126 EC CAP. 100UF 250 V
C919 645 046 3846 EC CAP. 222PF 2KV Z5U 7.5MM
C920 645 055 0140 EC CAP. 1000UF 35 V
C921 645 055 0140 EC CAP. 1000UF 35 V
C922 645 046 3617 EC CAP. 1000UF 16 V
C923 645 046 3617 EC CAP. 1000UF 16 V
C924 645 055 0133 EC CAP. 1000UF 25V =<13DIA
C925 645 055 0133 EC CAP. 1000UF 25V =<13DIA